Add PIDs for new Matrix Orbital GTT series products.
Signed-off-by: Troy Clark <tclark@matrixorbital.ca>
Cc: stable <stable@vger.kernel.org>
[johan: shorten commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Disable the MUSB interrupts till MUSB is recovered fully from BABBLE
condition. There are chances that we could get multiple interrupts
till the time the babble recover work gets scheduled. Sometimes
this could even end up in an endless loop making MUSB itself unusable.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a poll loop for max 25us for HS devices. Now guess what, I
tested it in gadget mode and forgot about the little detail. Nobody seem
to have it noticed…
This patch adds the missing logic for hostmode so it is recognized in
host and device mode properly.
Fixes: 50aea6fca7 ("usb: musb: cppi41: fire hrtimer according to
programmed channel length")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb registers can be dumped using the file regdump
which is created in debugfs. Up to now hard coded
register addresses are used for that. Different glue
layers however have different register addresses. The
patch addresses this issue by substituting bare register
addresses with defines.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On am335x-evm with musb in host mode and using it as a wakeup source the
following happens once the CPU comes out of suspend to ram:
|PM: Wakeup source MPU_WAKE
|PM: noirq resume of devices complete after 15.453 msecs
|PM: early resume of devices complete after 2.222 msecs
|PM: resume of devices complete after 507.351 msecs
|Restarting tasks ...
|------------[ cut here ]------------
|WARNING: CPU: 0 PID: 322 at drivers/usb/core/urb.c:339 usb_submit_urb+0x494/0x4c8()
|URB cc0db380 submitted while active
|[<c0348e64>] (usb_submit_urb) from [<c0340f94>] (hub_activate+0x2b8/0x49c)
|[<c0340f94>] (hub_activate) from [<c03411dc>] (hub_resume+0x14/0x1c)
|[<c03411dc>] (hub_resume) from [<c034be10>] (usb_resume_interface.isra.4+0xdc/0x110)
|[<c034be10>] (usb_resume_interface.isra.4) from [<c034beb0>] (usb_resume_both+0x6c/0x13c)
|[<c034beb0>] (usb_resume_both) from [<c034cca4>] (usb_runtime_resume+0x10/0x14)
|[<c034cca4>] (usb_runtime_resume) from [<c02bbd80>] (__rpm_callback+0x2c/0x60)
|[<c02bbd80>] (__rpm_callback) from [<c02bbdd4>] (rpm_callback+0x20/0x74)
|[<c02bbdd4>] (rpm_callback) from [<c02bcc48>] (rpm_resume+0x380/0x548)
|[<c02bcc48>] (rpm_resume) from [<c02bcb00>] (rpm_resume+0x238/0x548)
|[<c02bcb00>] (rpm_resume) from [<c02bd08c>] (__pm_runtime_resume+0x64/0x94)
|[<c02bd08c>] (__pm_runtime_resume) from [<c034b5a4>] (usb_autopm_get_interface+0x18/0x5c)
|[<c034b5a4>] (usb_autopm_get_interface) from [<c03438b8>] (hub_thread+0x10c/0x115c)
|[<c03438b8>] (hub_thread) from [<c005a70c>] (kthread+0xbc/0xd8)
|---[ end trace 036aa5fe78203142 ]---
|hub 1-0:1.0: activate --> -16
|hub 2-0:1.0: activate --> -16
The reason for this backtrace is the attempt of the USB code to resume
the HUB twice and thus enqueue the status URB twice.
Alan Stern was a great help by explaining how the USB code supposed to
work and what is most likely the problem. The root problem is that after
resume the musb runtime-suspend state remains RPM_SUSPENDED.
According to git log it RPM was added for the omap2430 platform. If I
understand it correct the omap2430 invokes a get on musb once a cable is
connected and a put once the cable is gone. In between the device could
go auto-idle/off. Not sure what happens when the device goes into suspend
but then I guess it was gadget only.
On DSPS I see only a get in probe and put in remove function. This would
forbid RPM from working but then the devices enterns suspended state
anyway :)
To get rid of this warning, I set the device state to RPM_ACTIVE which
the expected state.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were a two issues here.
1) We returned PTR_ERR(NULL) which means success if class_create()
failed.
2) If alloc_chrdev_region() failed then we should clean up before
returning.
Also kernel style is to have "error handling" as opposed to "success
handling". In the original code checking for "if (!status) " is
confusing and this bad style is what lead to bug #2.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We free "opts" on the error path and then dereference it.
Fixes: 21a9476a7b ('usb: gadget: hid: add configfs support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a UDC driver for Broadcom's USB3.0 Peripheral core named BDC.
BDC supports control traffic on ep0 and bulk/Int/Isoch traffic on all other
endpoints.
[ balbi@ti.com : fix build error on randconfig due to lack of
<linux/dmapool.h> ]
Signed-off-by: Ashwini Pahuja <ashwini.linux@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update DWC2 kconfig and makefile to support dual-role mode. The platform
file will always get compiled for the case where the controller is directly
connected to the CPU. So for loadable modules, dwc2.ko is built for host,
peripheral, and dual-role mode. The PCI bus interface will be called
dwc2_pci.ko and the platform interface module will be called dwc2_platform.ko.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since platform.c will get built for both Host and Gadget, if we leave the
usb_disabled() call in platform.c, it results in the following build error
when (!USB && USB_GADGET) condition is met.
ERROR: "usb_disabled" [drivers/usb/dwc2/dwc2_platform.ko] undefined!
Since usb_disabled() is mostly used to disable USB host functionality, move
the call the host portion for the DWC2 driver.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the dwc2 hcd driver is currently not looking for a clock node during
init, we should not completely fail if there isn't a clock provided.
By assigning clk = NULL, this allows the driver, when configured for dual-role
mode, to be able to continue loading the host portion of the driver when
a clock node is not specified.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make dwc2_handle_common_intr call the gadget interrupt function when operating
in peripheral mode. Remove the spinlock functions in s3c_hsotg_irq as
dwc2_handle_common_intr() already has the spinlocks.
Move the registeration of the IRQ to common code for platform and PCI.
Remove duplicate interrupt conditions that was in gadget, as those are handled
by dwc2 common interrupt handler.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initialize the USB driver to peripheral mode when a B-Device connector
is attached.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update suspend/resume to use dev_pm_ops API.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch will aggregate the probing of gadget/hcd driver into platform.c.
The gadget probe funtion is converted into gadget_init that is now only
responsible for gadget only initialization. All the gadget resources are now
handled by platform.c
Since the host workqueue will not get initialized if the driver is configured
for peripheral mode only. Thus we need to check for wq_otg before calling
queue_work().
Also, we move spin_lock_init to common location for both host and gadget that
is either in platform.c or pci.c.
We also move suspend/resume code to common platform code.
Lastly, move the "samsung,s3c6400-hsotg" binding into dwc2_of_match_table.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds the gadget data structure and appropriate data structure pointers
to the common dwc2_hsotg data structure. To keep the driver data
dereference code looking clean, the gadget variable declares are only available
for peripheral and dual-role mode. This is needed so that the dwc2_hsotg data
structure can be used by the hcd and gadget drivers.
Updates gadget.c to use the dwc2_hsotg data structure and gadget pointers
that have been moved into the common dwc2_hsotg structure.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Hcd controller needs bus_suspend/resume, dwc2 controller make
root hub generate suspend/resume signal with hprt0 register
when work in host mode.
After the root hub enter suspend, we can make controller enter
low power state with PCGCTL register.
We also update the lx_state for hsotg state.
This patch has tested on rk3288 with suspend/resume.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch expands USB-DMAC channels for R-Car Gen2 SoCs. The SoCs
have 4 channels. If d{2,3}_{t,x}x_id are not set, this driver never
uses the expanded USB-DMAC channels.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To extend DnFIFOs in the future, this patch adds a new macro because
some SoCs don't the "port" address for DnFIFOs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To expand DnFIFOs in the future, this patch standardizes the d{0,1}fifo
control using new macros.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To extend DnFIFOs in the future, this patch changes d{0,1}fifo of
usbhs_fifo_info to dfifo array.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/function/f_midi.c:1072:21: sparse: symbol 'f_midi_alloc' was not declared. Should it be static?
drivers/usb/gadget/legacy/gmidi.c:118:30: sparse: symbol 'fi_midi' was not declared. Should it be static?
drivers/usb/gadget/legacy/gmidi.c:119:21: sparse: symbol 'f_midi' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/function/f_hid.c:852:21: sparse: symbol 'hidg_alloc' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit e47d925 (usb: move the OTG state from
the USB PHY to the OTG structure) moved the
OTG state from struct usb_phy to struct usb_otg.
Unfortunately, even though I fixed quite a few
build regressions with that patch already, this
one was still missing.
Note that this driver still has other randconfig
build problems which I'll leave for driver author
to fix, as that's less trivial.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Currently scsi piggy backs on the block layer to define the concept
of a tagged command. But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them. Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.
We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.
Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We should be using the standard dev_printk() variants for
sense code printing.
[hch: remove __scsi_print_sense call in xen-scsiback, Acked by Juergen]
[hch: folded bracing fix from Dan Carpenter]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Replace the calls to __skb_alloc_page that are passed NULL with calls to
__dev_alloc_page.
In addition remove __GFP_COLD flag from allocations as we only want it for
the Rx buffer which is taken care of by __dev_alloc_skb, not for any
secondary allocations such as the queue element transmit descriptors.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e47d925 (usb: move the OTG state
from the USB PHY to the OTG structure) moved
the OTG state field from struct usb_phy to
struct usb_otg but, even though I fixed many
other build breakages, I still missed one
on ohci-omap.c.
Fix the build breakage now.
drivers/usb/host/ohci-omap.c: In function ‘start_hnp’:
drivers/usb/host/ohci-omap.c:186:19: error: request for member ‘state’ in something not a structure or union
hcd->usb_phy->otg.state = OTG_STATE_A_SUSPEND;
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for the new udc-core reset notifier to the
net2272 driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for the new udc-core reset notifier to the
net2280 driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SET_FEATURE request with DEBUG_MODE only worked the first time after module
initialisation. Per the USB 2.0 debug device specification, said request
is to be treated as if it were a SET_CONFIGURATION request, i.e. endpoint
must be re-configured.
As configure_endpoints() may now get called multiple times, move it outside
__init and move serial_alloc_tty() call into __init.
Code has assumption that endpoint mapping remains unchanged with consecutive
calls of configure_endpoints().
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The recent change bringing device-tree support triggers a warning in a
non device-tree build :
drivers/usb/gadget/udc/pxa27x_udc.c:2405:28: warning: 'udc_pxa_dt_ids'
defined but not used [-Wunused-variable]
Fix the warning with a preprocessor condition.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 6856d30 (usb: dwc3: ep0: return early
on NULL requests) tried to fix a minor corner
case where we could dereference a NULL pointer
but it also ended up introducing some dead code.
Unfortunately, that dead code, if reached, could
end up starving the endpoint request list because
a request would never be given back when it should.
Fix this by moving the check for empty request list
before its first use.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The FUSBH200 debug port has a EHCI-compatible register layout so there
is no need to define a custom struct.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that ehci-dbgp has its own header, use it rather than duplicating
the declarations, etc.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fotg210_dbg_port struct is a copy of the ehci_dbg_port definition
in the <linux/usb/ehci_def.h> header. Embedded in this definition are
a number of macros which came along for the ride. These macros are not
used in the fotg210 driver and will conflict those in the new
<linux/usb/ehci-dbgp.h> header.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_XEN_DOM0 is enabled, the ehci-dbgp driver notifies Xen of
controller reset events via xen_dbgp_reset_prep() and
xen_dbgp_external_startup() (via calls to xen_dbgp_op().) Otherwise
<linux/usb/ehci_def.h> defines them as no-ops to disable this logic.
The fotg210 driver copies much of the dbgp code from ehci_def.h, but it
unconditionally defines the Xen hooks as no-ops, effectively disabling
these notifications when CONFIG_EARLY_PRINTK_DBGP is disabled. When
enabled, though, notifying Xen is dependent on CONFIG_XEN_DOM0 due to
fotg210 leveraging the ehci-dbgp driver.
The following table compares the implementations of xen_dbgp_reset_prep()
and xen_dbgp_external_startup() in the ehci-dbgp and fotg210 drivers
under the relevant configurations:
EARLY_PRINTK_DBGP? XEN_DOM0? ehci-dbgp fotg210
------------------ --------- ------------- -------------
n n no-op no-op
n y xen_dbgp_op() no-op
y n no-op no-op
y y xen_dbgp_op() xen_dbgp_op()
This suggests that fotg210 is, at best, indifferent to whether Xen is
notified of these events. Make fotg210 consistent with ehci-dbgp as a
step towards consolidating this code duplication.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FUSBH200 debug port has a EHCI-compatible register layout so there
is no need to define a custom struct.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that ehci-dbgp has its own header, use it rather than duplicating
the declarations, etc.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fusbh200_dbg_port struct is a copy of the ehci_dbg_port definition
in the <linux/usb/ehci_def.h> header. Embedded in this definition are
a number of macros which came along for the ride. These macros are not
used in the fusbh200 driver and will conflict those in the new
<linux/usb/ehci-dbgp.h> header.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_XEN_DOM0 is enabled, the ehci-dbgp driver notifies Xen of
controller reset events via xen_dbgp_reset_prep() and
xen_dbgp_external_startup() (via calls to xen_dbgp_op().) Otherwise
<linux/usb/ehci_def.h> defines them as no-ops to disable this logic.
The fusbh200 driver copies much of the dbgp code from ehci_def.h, but it
unconditionally defines the Xen hooks as no-ops, effectively disabling
these notifications when CONFIG_EARLY_PRINTK_DBGP is disabled. When
enabled, though, notifying Xen is dependent on CONFIG_XEN_DOM0 due to
fusbh200 leveraging the ehci-dbgp driver.
The following table compares the implementations of xen_dbgp_reset_prep()
and xen_dbgp_external_startup() in the ehci-dbgp and fusbh200 drivers
under the relevant configurations:
EARLY_PRINTK_DBGP? XEN_DOM0? ehci-dbgp fusbh200
------------------ --------- ------------- -------------
n n no-op no-op
n y xen_dbgp_op() no-op
y n no-op no-op
y y xen_dbgp_op() xen_dbgp_op()
This suggests that fusbh200 is, at best, indifferent to whether Xen is
notified of these events. Make fusbh200 consistent with ehci-dbgp as a
step towards consolidating this code duplication.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some mass storage devices return a bogus value in response to a Get Max LUN
request. The Iomega Jaz USB Adapter responds with 0x10, hence my recent
patch to use the US_FL_SINGLE_LUN quirk for it.
The USB MSC Bulk Only Transport document says "The device shall return one
byte of data that contains the maximum LUN supported by the device."
Since the LUN field in the command block wrapper is only 4 bits wide, it
might be helpful to report too-large LUN values in the kernel log, and
assume max LUN is actually 0. That could get some devices which currently
need the US_FL_SINGLE_LUN quirk to work.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make the hid function available for gadgets composed with configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before configfs is integrated the usb_gstrings_attach() interface
must be used.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old function interface users left, so remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new f_hid interface in order for the old to be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting hid to the new function interface requires converting
the USB hid's function code and its users.
This patch converts the f_hid.c to the new function interface.
The file can now be compiled into a separate usb_f_hid.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far platform driver has been unregistered first,
so just after that the usb composite is still available,
but there is no hid data any more.
Reverse the order so that first the usb composite becomes
unavailable and second the hid data goes away.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
device_create() might fail, so check its return value and react
appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
class_create() might fail, so check its return value and react
appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add new quirk for devices that cannot handle control-line state
requests.
Note that we currently send these requests to all devices, regardless of
whether they claim to support it, but that errors are only logged if
support is claimed.
Since commit 0943d8ead3 ("USB: cdc-acm: use tty-port dtr_rts"), which
only changed the timings for these requests slightly, this has been
reported to cause occasional firmware crashes on Simtec Electronics
Entropy Key devices after re-enumeration. Enable the quirk for this
device.
Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Cc: stable <stable@vger.kernel.org> # v3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=egWd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.18-rc4
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two fixes of non-atomic allocations in write paths.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QlS+
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc4
Two fixes of non-atomic allocations in write paths.
Signed-off-by: Johan Hovold <johan@kernel.org>
File names in the heading comments fell out of favor long ago, and these weren't
even changed when the drivers were moved from drivers/usb/otg/, so remove them
at last...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The timeout argument to usb_stor_control_msg() is specified in jiffies, not
milliseconds.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the midi function available for gadgets composed with configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add configfs support the usb_gstrings_attach must be used.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old f_midi interface users left, so remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new f_midi interface so that the old can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting midi to the new function interface requires converting
the USB midi's function code and its users.
This patch converts the f_midi.c to the new function interface.
The file can now be compiled into a separate usb_f_midi.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kstrdup() might fail, so check its return value and react appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The soundcard index to use for the ALSA device creation is passed as a
parameter to f_midi_bind_config(), but is assigned to midi->index only
after the call to f_midi_register_card(midi). So no matter what is passed
to f_midi_bind_config(), the actual index for snd_card_new() is always 0.
This probably works ok if at the moment of f_midi's bind there are no
other snd_cards, but if there are, it is not possible to bind f_midi.
This patch moves the assignment to a place before the call to
f_midi_register_card(midi).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
uac1 and uac2 functions are available through the configfs interface
and it should be possible to build them without building their legacy
gadgets.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Attaching a keyboard, using it as a wakeup via
|for f in $(find /sys/devices/ocp.3/47400000.usb -name wakeup)
|do
| echo enabled > $f
|done
going into standby
| echo standby > /sys/power/state
and now a wake up by a pressing a key.
What happens is that the system wakes up but the USB device is dead. The
USB stack tries to send a few control URBs but nothing comes back.
Eventually it gaves up and the device remains dead:
|[ 632.559678] PM: Wakeup source USB1_PHY
|[ 632.581074] PM: noirq resume of devices complete after 21.261 msecs
|[ 632.607521] PM: early resume of devices complete after 10.360 msecs
|[ 632.616854] net eth2: initializing cpsw version 1.12 (0)
|[ 632.704126] net eth2: phy found : id is : 0x4dd074
|[ 636.704048] libphy: 4a101000.mdio:00 - Link is Up - 1000/Full
|[ 638.444620] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 653.713435] usb 1-1: device descriptor read/64, error -110
|[ 669.093435] usb 1-1: device descriptor read/64, error -110
|[ 669.473424] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 684.743436] usb 1-1: device descriptor read/64, error -110
|[ 690.065097] PM: resume of devices complete after 57450.744 msecs
|[ 690.076601] PM: Finishing wakeup.
|[ 690.076627] Restarting tasks ...
It seems that since we got woken up via MUSB_INTR_RESUME the
musb_host_finish_resume() callback is executed before the
resume-callbacks of the PHY and glue layer are invoked. If I delay it
until the glue layer resumed then I don't see this problem.
I also move musb_host_resume_root_hub() into that callback since I don't
see any reason in doing anything resume-link if there are still pieces
not restored.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure to only raise DTR on transitions from B0 in set_termios.
Also allow set_termios to be called from open with a termios_old of
NULL. Note that DTR will not be raised prematurely in this case.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The am335x-evmsk support two kinds of suspend:
- standby
the USB device remains powered while the system goes into suspend
- mem
the USB device becomes powerless while the system goes into suspend.
In the "standby" case the device resumes quickly. In the "mem" case the
system hangs for a few seconds. It seems to me that the USB-device has
no address (it was disconnected) and the USB stack thinks that it is
fully operational and GetPortStatus returns the status from before the
suspend so it is not a big help here.
This adds a check in the resume path to see if the device mode (A or B)
and the speed is the same. If the device went missing between
suspend/resume (VBUS went down) then MUSB seems to go into B mode and
HS/FS bits are cleared. In that case we clear the port1_status bits and
assume a disconnect. Once the stack learns this it does a "logical
disconnect" and removes the USB-device quickly. Should the device remain
connected during the suspend then MUSB will receives a "CONNECT" interrupt.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DCPCTR doesn't have the ACLRM bit, the usbus_pipe_clear()
should not call the usbhsp_pipectrl_set() with ACLRM.
So, this patch fixes this issue to add the usbhs_fifo_clear_dcp()
in fifo.c because the controller needs the CFIFO to clear the
the DCP PIPE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, this driver should clear the INTSTS0.CTRT
bit before this controller detects the next stage transition. Otherwise,
the driver may not be able to clear the bit after the controller went to
the next stage transition. After that, the driver will not be able to
clear the INTSTS0.VALID, and a usb control transfer will not finish
finally.
If we use the testusb tool, it is easy to reproduce this issue:
# testusb -a -t 10
Since the previous code handled a data stage and a status stage in
the usbhsf_pio_try_push(), it may not clear the INTSTS0.CTRT at the
right timing.
So, this patch change the timing of usbhs_dcp_control_transfer_done()
to the usbhsg_irq_ctrl_stage().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that this driver always enable the D+ pullup
after it detected the VBUS connection even though this usb controller
can control the D+ pullup timing by software. So, this driver should
enable the D+ pullup after a gadget driver called usb_gadget_connect().
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the NULL pointer dereference happens
when we uses g_audio driver. Since the g_audio driver will call
usb_ep_disable() in afunc_set_alt() before it calls usb_ep_enable(),
the uep->pipe of renesas usbhs driver will be NULL. So, this patch
adds a condition to avoid the oops.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2f98382dc (usb: renesas_usbhs: Add Renesas USBHS Gadget)
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit bda9893c50 as it was
incorrect.
Reported-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Google devices that export simple serial
interfaces using the vendor specific SubClass/Protocol pair
0x50/0x01.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
[johan: move id entries and update Kconfig]
Signed-off-by: Johan Hovold <johan@kernel.org>
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci/ohci-platform just define .suspend/.resume functions for dev_pm_ops,
but in order to support both STR(suspend-to-ram) and hibernation, other
callbacks such as .freeze/.thaw are also required.
Registering all required callbacks for both STR and hibernation can
be done by SIMPLE_DEV_PM_OPS macro function.
Signed-off-by: Wonhong Kwon <wonhong.kwon@lge.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use %pad for dma_addr_t, because a dma_addr_t type can vary
based on build options. So, it prevents the following build
warnings in printks.
drivers/usb/host/imx21-hcd.c:1175:2: warning: format '%X' expects argument of type 'unsigned int', but argument 8 has type
'dma_addr_t' [-Wformat]
drivers/usb/host/imx21-hcd.c:1175:2: warning: format '%X' expects argument of type 'unsigned int', but argument 10 has type
'dma_addr_t' [-Wformat]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the integer variable 'feature' was not being used anywhere in the function.
so it is safe to remove the variable.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No caller or macro uses the return value so make it void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary mach/* headers to be able to converge to a multiplatform
kernel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This puts all of the platform_data checks in the same place, and removes
the need for a custom drv->reset() callback.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These quirks are currently set through platform_data; allow DT-based SoCs
to use them too.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm63xx and bcm3384 platforms need to set OHCI_QUIRK_FRAME_NO, but
they are non-PPC platforms and don't enable CONFIG_PPC_MPC52xx.
Therefore this patch changes the code that uses OHCI_QUIRK_FRAME_NO,
making it not depend on CONFIG_PPC_MPC52xx.
Also, rephrase the comments describing OHCI_QUIRK_FRAME_NO and the
related PSW endian swap.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an external portpower override callback, only single
port regulator control is supported now.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current EHCI implementation is prepared to toggle the
PORT_POWER bit to enable or disable a USB-Port. In some
cases this port power can not be just toggled by the PORT_POWER
bit, and the gpio-regulator is needed to be toggled too.
This patch defines a port power control interface ehci_port_power for
ehci core use, it toggles PORT_POWER bit as well as calls platform
defined .port_power if it is defined.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With uas over usb-3 the tags inside the uas iu-s must match the usb-3 stream
ids, and those go from 1 - qdepth.
Before blk-mq calling scsi_activate_tcq(sdev, qdepth) guaranteed that we would
only get cmnd->request->tag from 0 - (qdepth - 1), and we used those as
uas-tags / stream-ids.
With blk-mq however we are guaranteed to never get more then qdepth commands
queued at the same time, but the cmnd->request->tag values may be much larger,
which breaks uas.
This commit fixes this by generating uas tags in the 1 - qdepth range ourselves
instead of using cmnd->request->tag.
While touching all involved code anyways also rename the uas_cmd_info stream
field to uas_tag, because when using uas over usb-2 streams are not used.
Cc: Christoph Hellwig <hch@infradead.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
--
Changes in v2:
-Remove ".disable_blk_mq = true" from uas_host_template
Changes in v3:
-Rebased on top of Linus' current master branch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modifies the usb_authorize_device() function such as that it does
not reload the device descriptor for wired devices. The reasons for this
are as follows:
* Some devices dislike the master requesting the descriptor from them twice,
failing on the usb_get_device_descriptor() call with -ETIMEOUT. Observed this
on my Pretec 16GB flash drive (4146:ba65).
* Malicious device could send two different descriptors - one before
authorization, used by userspace to determine whether to authorize it and
second to be actually used by the kernel when determining which drivers to
bind.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
removed the Kconfig symbol PLAT_S5P. Remove two optional dependencies on
that symbol from this Kconfig file too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On enabling CONFIG_OF_SELFTEST which enables CONFIG_OF_DYNAMIC,
we found out that while getting PHYs for the controller we were
doing an extra of_node_put on the child node in our routines -
exynos_e/ohci_get_phy().
This child is however already put by of_get_next_available_child()
which does a of_node_put() on the "prev" node. So there's no point
in putting the same node again in our routine.
Reported-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's drop the warning for modems with unusual capabilities,
the associated quirk and blacklist. They made little sense.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device-id entry for GW Instek AFG-2225, which has a byte swapped
bInterfaceSubClass (0x20).
Reported-by: Karl Palsson <karlp@tweak.net.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allows the gadget portion of the DWC2 driver to get built when
(!USB && USB_GADGET) condition is encountered.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for AMD Nolan (NL) FPGA and SoC platform.
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is recommended to set USB3 and USB2 SUSPHY bits to '1' after the core
initialization is completed above the dwc3 revision 1.94a.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It enables hibernation if the function is set in coreConsultant.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support of the PHY framework for ChipIdea drivers.
Changes are done in both the ChipIdea common code and in the drivers
accessing the PHY. This is done by adding a new PHY member in
ChipIdea's structures and by taking care of it in the code.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/udc/r8a66597-udc.c:1849:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added failure check for usb_assign_descriptors call in bind function.
Acked-By: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Pavitrakumar Managutte <pavitra1729@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 0ec8fd70fb ("USB: musb: fix possible panic while resuming")
musb_resume() became musb_resume_early() in order to enable the clocks
early on resume. This piece of the resume code was removed later in
commit 034917612 ("usb: musb: move clock handling to glue layer").
In between the function was renamed from musb_resume_early() to
musb_resume_noirq() by commit commit 48fea9659e ("USB: Rework musb
suspend()/resume_early()").
Now I see that first musb_core is resumed followed by phy and glue
layer and I ask myself is this really what we intend to do? This kind
of revoked the purpose of the first commit (0ec8fd70fb).
Because of this and because it looks wrong to resume (core) before the
glue layer I push it to the ->resume callback.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves calls to phy enable/disable out of spinlock protected
blocks in device suspend/resume to fix incorrect caller context. Phy
related functions must not be called from atomic context. To protect
device internal state from a race during suspend, a call to
s3c_hsotg_core_disconnect() is added under a spinlock, what prevents any
further activity on the usb bus.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves udc initialization from pullup() method to
s3c_hsotg_udc_start(), so that method ends with hardware fully
initialized and left in soft-disconnected state. After this change, the
pullup() method simply clears soft-disconnect start() when called with
is_on=1. For completeness, a call to s3c_hsotg_core_disconnect() has
been added when pullup() method is called with is_on=0, what puts the
udc hardware back to soft-disconnected state.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves phy enable/disable calls from pullup() method to
udc_start/stop functions. This solves the issue related to limited caller
context for PHY functions, because they cannot be called from non-sleeping
context. This is also a preparation for using soft-disconnect feature of
udc controller in pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch changes s3c_hsotg_core_init function to leave hardware in
soft disconnect mode, so the moment of coupling the hardware to the usb
bus can be later controlled by the separate functions for enabling and
disabling soft disconnect mode. This patch is a preparation to rework
pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes duplicated code and sets last_rst variable in the
function which does the hardware reset.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
