This makes the value from which an object should be considered "near"
available to userspace. This hardware-dependent value should be set
in the device-tree.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Link: https://lore.kernel.org/r/20220420112540.91907-3-arnaud.ferraris@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
While at it, reuse temporary device pointer in the same function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220413181402.19582-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nothing in this driver depends on OF firmware so drop the dependency
to remove the false impression such a dependency exists.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220413184627.21125-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Among all the users of the kfifo buffers, no one uses the
INDIO_BUFFER_HARDWARE mode. So let's take this as a general rule and
simplify a little bit the internals - overall the documentation - by
eliminating unused specific cases. Use the INDIO_BUFFER_SOFTWARE mode by
default with kfifo buffers, which will basically mimic what all the "non
direct" modes do.
Cc: Benson Leung <bleung@chromium.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Jyoti Bhayana <jbhayana@google.com>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220207143840.707510-13-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-50-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM support is simpler and less error prone than the
use of #ifdef based config guards.
Use the new DEFINE_RUNTIME_DEV_PM_OPS to reduce boilerplate.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-47-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-29-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Vaishnav M A <vaishnav@beagleboard.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-28-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-27-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-26-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Luca Weiss <luca@z3ntu.xyz>
Cc: Martijn Braam <martijn@brixit.nl>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-25-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Maslov Dmitry <maslovdmitry@seeed.cc>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-24-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-23-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-22-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Brian Masney <masneyb@onstation.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-21-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards. Also switch to SIMPLE_DEV_PM_OPS rather
than opencoding the same.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-20-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-19-jic23@kernel.org
In order to avoid unnecessary pollution of the global symbol namespace
move the common/library functions into a specific namespace and import
that into the bus specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-16-jic23@kernel.org
sysfs_emit() is preferred over raw s*printf() for sysfs attributes since it
knows about the sysfs buffer specifics and has some built-in checks for
size and alignment.
Use sysfs_emit() to format the custom device attributes of the lm3533
driver. Note this driver was using scnprintf correctly so this change
is about ensuring examples of code that might get cut and paste into new
drivers are using current best practice.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211216185217.1054495-8-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The spacing in this driver was inconsistent so make sure we have a space
after { and before } for the two id tables.
Part of aim is to avoid providing examples of this inconsistency that
get copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Nikita Travkin <nikita@trvn.ru>
Cc: Maslov Dmitry <maslovdmitry@seeed.cc>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211230174911.78291-6-jic23@kernel.org
The spacing in this driver was inconsistent so make sure we have a space
after { and before } for the two id tables.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211230174911.78291-5-jic23@kernel.org
Having a space after the { and not one before the } is inconsistent and
I'd rather not have examples of this that get copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211230174911.78291-4-jic23@kernel.org
One case in here was inconsistent and was main focus of this patch.
In that case there was a space after the { and none before the }.
The second case was then inconsistent in having now spaces.
Change makes sure there are spaces.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211230174911.78291-3-jic23@kernel.org
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
-----BEGIN PGP SIGNATURE-----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=xXvq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 5.17
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
MAINTAINERS: Add maintainer for xilinx-ams
dt-bindings: iio: adc: Add Xilinx AMS binding documentation
iio: adc: Add Xilinx AMS driver
device property: Add fwnode_iomap()
iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
iio:dummy: Drop set but unused variable len.
iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
drivers:iio:dac: Add AD3552R driver support
dt-bindings: iio: dac: Add adi,ad3552r.yaml
...
This enables use of other firmware types with minimal driver changes.
Part of an ongoing effort to move all IIO drivers over to generic
accessors in order to reduce the chance of of_* versions being
copied into new drivers. Also updated the headers to reflect this change
including using mod_devicetable.h for struct of_device_id definition
rather than going via of.h
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Userspace tools like iio-sensor-proxy need to know the proximity level
that should be considered "near". This value is hardware-specific and
can be defined via the devicetree. Allow the driver to export the near
level.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20211125125646.54831-2-nikita@trvn.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Interrupt handlers must return one of the irqreturn_t values. Returning a
error code is not supported.
The stk3310 event interrupt handler returns an error code when reading the
flags register fails.
Fix the implementation to always return an irqreturn_t value.
Fixes: 3dd477acbd ("iio: light: Add threshold interrupt support for STK3310")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-3-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Fixes: 2690be9051 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously ltr501 driver supported a number of light and,
proximity sensors including ltr501, ltr559 and ltr301.
This adds support for another light sensor ltr303
used in Seeed Studio reTerminal, a carrier board
for Raspberry Pi 4 CM.
Signed-off-by: Maslov Dmitry <maslovdmitry@seeed.cc>
Link: https://lore.kernel.org/r/20211106174137.6783-1-maslovdmitry@seeed.cc
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO core handles a trigger ops with all NULL callbacks the
same as if the trigger ops itself was NULL.
Remove the empty trigger ops from the interrupt trigger driver to slightly
reduce the boilerplate code. Object size of the driver module is also
slightly reduced.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211031142130.20791-8-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092656.421-3-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211008092656.421-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add of_device_id table so the driver can be used on DT platforms without
relying on i2c_device_id fallback. (So DT schema validation is possible)
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20211006163058.145842-4-nikita@trvn.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On some platforms the supply regulators must be enabled before the
sensor can work. Add vdd and vddio regulators for the sensor and IO bus
power respectively.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20211006163058.145842-3-nikita@trvn.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
-----BEGIN PGP SIGNATURE-----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=htmG
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of IIO new device and feature support for the 5.16 cycle
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
* tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (148 commits)
iio: imx8qxp-adc: mark PM functions as __maybe_unused
iio: pressure: ms5611: Make ms5611_remove() return void
iio: potentiometer: max5487: Don't return an error in .remove()
iio: magn: hmc5843: Make hmc5843_common_remove() return void
iio: health: afe4403: Don't return an error in .remove()
iio: dac: ad5686: Make ad5686_remove() return void
iio: dac: ad5592r: Make ad5592r_remove() return void
iio: dac: ad5446: Make ad5446_remove() return void
iio: dac: ad5380: Make ad5380_remove() return void
iio: accel: mma7455: Make mma7455_core_remove() return void
iio: accel: kxsd9: Make kxsd9_common_remove() return void
iio: accel: bmi088: Make bmi088_accel_core_remove() return void
iio: accel: bmc150: Make bmc150_accel_core_remove() return void
iio: accel: bma400: Make bma400_remove() return void
drivers:iio:dac:ad5766.c: Add trigger buffer
iio: triggered-buffer: extend support to configure output buffers
iio: kfifo-buffer: Add output buffer support
iio: Add output buffer support
iio: documentation: Document scd4x calibration use
drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor
...
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210928014156.1491-4-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210928014156.1491-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a simple conversion. Both iio_device_register() and
iio_triggered_buffer_setup() functions have device-managed variants.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913120002.306280-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-6-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an of_device_id table to explicitly support the Capella cm3323
Ambient Light Sensor rather than relying on matching against the
i2c_device_id table.
Signed-off-by: Siddharth Manthan <siddharth.manthan@gmail.com>
Link: https://lore.kernel.org/r/20210728110048.14593-2-siddharth.manthan@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The continue statement at the end of a for-loop has no effect,
remove it.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210617081312.151746-1-colin.king@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the driver to use only device-managed init routines in
the probe function of the driver.
This way, we no longer need the tcs3414_remove() hook.
We still need to keep the i2c_set_clientdata() call, as that's being used
for the PM routines.
And lastly, a devm_add_action_or_reset() hook is added to call the
powerdown handler when the chip is uninitialized or the probe fails.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210624080534.9209-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that the driver's buffer is stored on the adjd_s311_data private
object, the driver is a simple conversion to use only device-managed
functions in the probe.
The iio_triggered_buffer_setup() and iio_device_register() functions are
the only ones needing conversion.
And i2c_set_clientdata() is no longer required.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210705071456.649659-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change moves the entire buffer on the private adjd_s311_data type.
Since the device has 4 channels, it's not a big waste to just allocate the
maximum possible buffer and use only what's needed.
This is in contrast with free-ing and re-allocating the buffer on the
update_scan_mode hook.
Since the driver pushes buffer data with
iio_push_to_buffers_with_timestamp(), the buffer must also include a
64-bit buffer for the timestamp, for each sample-set.
With this change, the adjd_s311_update_scan_mode() is no longer needed.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210705071456.649659-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some HID drivers use devm_kmemdup() already to clone the template IIO
channels information and update it.
However, there are still some drivers that kmemdup() and kfree() the
channels.
This change converts them to use devm_kmemdup() and bind the life-time of
this allocated object to the parent device object (in these drivers).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210630123029.759609-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allocating an IRQ is conditional to the IRQ existence, but freeing it
was not. If no IRQ was allocate, the driver would still try to free
IRQ 0. Add the missing checks.
This fixes the following trace when the driver is removed:
[ 100.667788] Trying to free already-free IRQ 0
[ 100.667793] WARNING: CPU: 0 PID: 2315 at kernel/irq/manage.c:1826 free_irq+0x1fd/0x370
...
[ 100.667914] Call Trace:
[ 100.667920] tcs3472_remove+0x3a/0x90 [tcs3472]
[ 100.667927] i2c_device_remove+0x2b/0xa0
Signed-off-by: frank zago <frank@zago.net>
Link: https://lore.kernel.org/r/20210427022017.19314-2-frank@zago.net
Fixes: 9d2f715d59 ("iio: light: tcs3472: support out-of-threshold events")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
General driver churn doesn't always include updates of header includes.
Manual review of the output of the include-what-you-use checker lead to the
following cleanup. Hopefuly this brings things back to a good state for the
hid-sensor drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210608205510.4033887-1-jic23@kernel.org
