In order to prevent "crushed blacks" on TVs, the range of the RGB output
may be limited to 16-235. This used to be available through Xorg under
the "Broadcast RGB" option, so reintroduce support for KMS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34543
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The code paths for modesetting are growing in complexity as we may need
to move the buffers around in order to fit the scanout in the aperture.
Therefore we face a choice as to whether to thread the interruptible status
through the entire pinning and unbinding code paths or to add a flag to
the device when we may not be interrupted by a signal. This does the
latter and so fixes a few instances of modesetting failures under stress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we just need a temporary array whilst performing the relocations for
the execbuffer, first attempt to allocate using kmalloc even if it is
not of order page-0. This avoids the overhead of remapping the
discontiguous array and so gives a moderate boost to execution
throughput.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Seems like we are forever to be cursed with buggy firmware, so allow the
user to explicitly set the panel connection status.
Of secondary utility for cases where I run laptops with the lid closed,
but still want to configure the LVDS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dave Airlie spotted that we had a potential bug should we ever rearrange
the drm_i915_gem_object so not the base drm_gem_object was not its first
member. He noticed that we often convert the return of
drm_gem_object_lookup() immediately into drm_i915_gem_object and then
check the result for nullity. This is only valid when the base object is
the first member and so the superobject has the same address. Play safe
instead and use the compiler to convert back to the original return
address for sanity testing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In a few places I replaced reads of per-pipe registers with the actual
register offsets themselves (converting I915_READ(reg) to _PIPE(reg)).
Alexey caught this on his 9xx machine because the cursor control write
was affected. A quick audit showed a few more places where I'd borked
a read, so here's a patch to fix things up.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: compilation fix]
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 633f2ea266 and the
attempted fix dcbe6f2b3d.
There is a single clock source used for both SSC (some LVDS and DP) and
non-SSC (VGA, DVI) outputs. So we need to be careful to only enable SSC
as necessary. However, fiddling with DREFCLK was causing DP links to be
dropped and we do not have a fix ready, so revert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Grab the latest stabilisation bits from -fixes and some suspend and
resume fixes from linus.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
Share the lid detection code for the all panels for consistent behaviour
and a single place to add the eventual quirks for crap hardware.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can enable some safely, but FDI and transcoder interrupts can occur
and block other interrupts from being detected (like port hotplug
events). So keep them disabled by default (they can be re-enabled for
debugging display bringup, but should generally be off).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: hopefully fix pll issues for real (v3)
drm/radeon/kms: add bounds checking to avivo pll algo
drm: fix wrong usages of drm_device in DRM Developer's Guide
drm/radeon/kms: fix a few more atombios endian issues
drm/radeon/kms: improve 6xx/7xx CS error output
drm/radeon/kms: check AA resolve registers on r300
drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
drm/radeon/kms: use linear aligned for evergreen/ni bo blits
drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
drm/radeon: fix race between GPU reset and TTM delayed delete thread.
drm/radeon/kms: evergreen/ni big endian fixes (v2)
drm/radeon/kms: 6xx/7xx big endian fixes
drm/radeon/kms: atombios big endian fixes
drm/radeon: 6xx/7xx non-kms endian fixes
drm/radeon/kms: optimize CS state checking for r100->r500
drm: do not leak kernel addresses via /proc/dri/*/vma
drm/radeon/kms: add connector table for mac g5 9600
radeon mkregtable: Add missing fclose() calls
drm/radeon/kms: fix interlaced modes on dce4+
drm/radeon: fix memory debugging since d961db75ce
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
pci: use security_capable() when checking capablities during config space read
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / Video: Probe for output switch method when searching video devices.
ACPI / Wakeup: Enable button GPEs unconditionally during initialization
ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
dmaengine: add slave-dma maintainer
dma: ipu_idmac: do not lose valid received data in the irq handler
dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
dmaengine i.MX dma: initialize dma capabilities outside channel loop
dmaengine i.MX DMA: do not initialize chan_id field
dmaengine i.MX dma: check sg entries for valid addresses and lengths
dmaengine i.MX dma: set maximum segment size for our device
dmaengine i.MX SDMA: reserve channel 0 by not registering it
dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
dmaengine i.MX SDMA: do not initialize chan_id field
dmaengine i.MX sdma: check sg entries for valid addresses and lengths
dmaengine i.MX sdma: set maximum segment size for our device
DMA: PL08x: fix channel pausing to timeout rather than lockup
DMA: PL08x: fix infinite wait when terminating transfers
dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, dmi, debug: Log board name (when present) in dmesg/oops output
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
x86: Fix mwait_usable section mismatch
x86: Readd missing irq_to_desc() in fixup_irq()
x86: Fix section mismatch in LAPIC initialization
This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea. The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space. The normal capable() interface returns
true on success, but the LSM interface returns 0 on success. This thinko
is now fixed in this patch, and has been confirmed to work properly.
So, once again...Eric Paris noted that commit de139a3 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.
( Please note that Type 2 is not listed in Table 3 in Sec 6.2
("Required Structures and Data") of the SMBIOS v2.7
Specification. )
Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.
Before the fix:
(i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6
After the fix:
(i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.
v2: testing options
v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852https://bugzilla.kernel.org/show_bug.cgi?id=24462https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: Fix minor compile warning
RTC: Convert rtc drivers to use the alarm_irq_enable method
RTC: Fix rtc driver ioctl specific shortcutting
Currently when two or more buffers are queued by the camera driver
and so the double buffering is enabled in the idmac, we lose one
frame comming from CSI since the reporting of arrival of the first
frame is deferred by the DMAIC_7_EOF interrupt handler and reporting
of the arrival of the last frame is not done at all. So when requesting
N frames from the image sensor we actually receive N - 1 frames in
user space.
The reason for this behaviour is that the DMAIC_7_EOF interrupt
handler misleadingly assumes that the CUR_BUF flag is pointing to the
buffer used by the IDMAC. Actually it is not the case since the
CUR_BUF flag will be flipped by the FSU when the FSU is sending the
<TASK>_NEW_FRM_RDY signal when new frame data is delivered by the CSI.
When sending this singal, FSU updates the DMA_CUR_BUF and the
DMA_BUFx_RDY flags: the DMA_CUR_BUF is flipped, the DMA_BUFx_RDY
is cleared, indicating that the frame data is beeing written by
the IDMAC to the pointed buffer. DMA_BUFx_RDY is supposed to be
set to the ready state again by the MCU, when it has handled the
received data. DMAIC_7_CUR_BUF flag won't be flipped here by the
IPU, so waiting for this event in the EOF interrupt handler is wrong.
Actually there is no spurious interrupt as described in the comments,
this is the valid DMAIC_7_EOF interrupt indicating reception of the
frame from CSI.
The patch removes code that waits for flipping of the DMAIC_7_CUR_BUF
flag in the DMAIC_7_EOF interrupt handler. As the comment in the
current code denotes, this waiting doesn't help anyway. As a result
of this removal the reporting of the first arrived frame is not
deferred to the time of arrival of the next frame and the drivers
software flag 'ichan->active_buffer' is in sync with DMAIC_7_CUR_BUF
flag, so the reception of all requested frames works.
This has been verified on the hardware which is triggering the
image sensor by the programmable state machine, allowing to
obtain exact number of frames. On this hardware we do not tolerate
losing frames.
This patch also removes resetting the DMA_BUFx_RDY flags of
all channels in ipu_disable_channel() since transfers on other
DMA channels might be triggered by other running tasks and the
buffers should always be ready for data sending or reception.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915: Fix resume regression from 5d1d0cc
drm/i915/tv: Use polling rather than interrupt-based hotplug
drm/i915: Trigger modesetting if force-audio changes
drm/i915/sdvo: If we have an EDID confirm it matches the mode of the connection
drm/i915: Disable RC6 on Ironlake
drm/i915/lvds: Restore dithering on native modes for gen2/3
drm/i915: Invalidate TLB caches on SNB BLT/BSD rings
Makes debugging CS rejections much easier.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is an important security fix because we allowed arbitrary values
to be passed to AARESOLVE_OFFSET. This also puts the right buffer address
in the register.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My evergreen has been in a remote PC for week and reset has never once
saved me from certain doom, I finally relocated to the box with a
serial cable and noticed an oops when the GPU resets, and the TTM
delayed delete thread tries to remove something from the GTT.
This stops the delayed delete thread from executing across the GPU
reset handler, and woot I can GPU reset now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on 6xx/7xx endian fixes from Cédric Cano.
v2: fix typo in shader
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The colorbuffer, zbuffer, and texture states are checked only once when
they get changed. This improves performance in the apps which emit
lots of draw packets and few state changes.
This drops performance in glxgears by a 1% or so, but glxgears is not
a benchmark we care about.
The time spent in the kernel when running Torcs dropped from 33% to 23%
and the frame rate is higher, which is a good thing.
r600 might need something like this as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the continuing effort to avoid kernel addresses leaking to unprivileged
users, this patch switches to %pK for /proc/dri/*/vma.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
PPC Mac cards do not provide connector tables in
their vbios. Their connector/encoder configurations
must be hardcoded in the driver.
verified by nyef on #radeon
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/mkregtable.c:parser_auth() almost always remembers
to fclose(file) before returning, but it misses two spots.
This is not really important since the process will exit shortly after and
thus close the file for us, but being explicit prevents static analysis
tools from complaining about leaked memory and missing fclose() calls and
it also seems to be the prefered style of the existing code to explicitly
close the file.
So, here's a patch to add the two missing fclose() calls.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- set scaler table clears the interleave bit, need to
reset it in encoder quirks, this was already done for
pre-dce4.
- remove the interleave settings from set_base() functions
this is now handled in the encoder quirks functions, and
isn't technically part of the display base setup.
- rename evergreen_do_set_base() to dce4_do_set_base() since
it's used on both evergreen and NI asics.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28182
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old code dereferenced a value, the new code just needs to pass
the ptr.
fixes an oops looking at files in debugfs.
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
devicetree-discuss is moderated for non-subscribers
MAINTAINERS: Add entry for GPIO subsystem
dt: add documentation of ARM dt boot interface
dt: Remove obsolete description of powerpc boot interface
dt: Move device tree documentation out of powerpc directory
spi/spi_sh_msiof: fix wrong address calculation, which leads to an Oops
This reverts commit 47970b1b2a.
It turns out it breaks several distributions. Looks like the stricter
selinux checks fail due to selinux policies not being set to allow the
access - breaking X, but also lspci.
So while the change was clearly the RightThing(tm) to do in theory, in
practice we have backwards compatibility issues making it not work.
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: David Airlie <airlied@linux.ie>
Acked-by: Alex Riesen <raa.lkml@gmail.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch reverts one hunk of 677bd810ee
"ACPI video: remove output switching control", namely the removal of
probing for _DOS/_DOD when searching for video devices.
This is needed on some Fujitsu Laptops (at least S7110, P8010) for the
ACPI backlight interface to work, as an these machines, neither ROM nor
posting methods are available, and after removal of output switching,
none of the caps triggers, which prevents the backlight search from
being entered.
Tested on a Fujitsu Lifebook S7110 and Fujitsu Lifebook P8010.
This probably fixes https://bugzilla.kernel.org/show_bug.cgi?id=27312
for the people who have no entry in /sys/class/backlight.
This is the complete list of public (starting with "_") methods implemented
on the S7110, BIOS rev 1.34:
\_SB_.PCI0.GFX0._ADR
\_SB_.PCI0.GFX0._DOS
\_SB_.PCI0.GFX0._DOD
\_SB_.PCI0.GFX0.CRT._ADR
\_SB_.PCI0.GFX0.CRT._DCS
\_SB_.PCI0.GFX0.CRT._DGS
\_SB_.PCI0.GFX0.CRT._DSS
\_SB_.PCI0.GFX0.LCD._ADR
\_SB_.PCI0.GFX0.LCD._BCL
\_SB_.PCI0.GFX0.LCD._BCM
\_SB_.PCI0.GFX0.LCD._BQC
\_SB_.PCI0.GFX0.LCD._DCS
\_SB_.PCI0.GFX0.LCD._DGS
\_SB_.PCI0.GFX0.LCD._DSS
\_SB_.PCI0.GFX0.LCD._PS0
\_SB_.PCI0.GFX0.LCD._PS3
\_SB_.PCI0.GFX0.TV._ADR
\_SB_.PCI0.GFX0.TV._DCS
\_SB_.PCI0.GFX0.TV._DGS
\_SB_.PCI0.GFX0.TV._DSS
\_SB_.PCI0.GFX0.DVI._ADR
\_SB_.PCI0.GFX0.DVI._DCS
\_SB_.PCI0.GFX0.DVI._DGS
\_SB_.PCI0.GFX0.DVI._DSS
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
