- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These values must be initialized to zero, otherwise the hardware could
reuse previous values, especially the rate index
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It bypasses the MCU, so it does not belong in mcu.c
Also make mt7615_mac_tx_rate_val static
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7615_mcu_send_ram_firmware routine since mt7615_load_ram runs the
same code to send ram firmware to cr4 and n9 mcus. Moreover rename
gen_dl_mode in mt7615_mcu_gen_dl_mode.
This patch does not introduce any behaviour change, it is just code
refactor.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Release patch semaphore even if request_firmware fails in
mt7615_load_patch
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we don't clean that tx queue from the tx tasklet, we need to do it
after the firmware upload is done. This patch also adds a cleanup step during
the upload, to help reclaim memory faster.
Fixes unprocessed queued frames eating up memory long after the firmware
upload has already completed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_rdd_send_pattern routine to trigger a radar pattern
detection. Moreover move debugfs related routines in a dedicated source
file.
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Channel Switch Announcement support to mt7615 driver updating beacon
template with CSA IE received from mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Delay channel calibration after Channel Availability Check. Add some
code cleanup to mt7615_mcu_set_channel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_regd_notifier callback. This is a preliminary patch to
add radar detection support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning in __mt7615_mcu_msg_send:
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
restricted __le16 degrades to integer
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
cast from restricted __le16
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Realtek Bluetooth controller provides a BT_DIS reset pin for hardware
reset of it. The cmd_timeout is helpful on Realtek bluetooth controller
where the firmware gets stuck.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the issue that when the FW size is 32K+, it will fail for the download
process because of the incorrect index.
When firmware patch length is over 32K, "dl_cmd->index" may >= 0x80. It
will be thought as "data end" that download process will not complete.
However, driver should recount the index from 1.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct mgmt_rp_get_connections {
...
struct mgmt_addr_info addr[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*rp) + (i * sizeof(struct mgmt_addr_info));
with:
struct_size(rp, addr, i)
Also, notice that, in this case, variable rp_len is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These printing macros already add a trailing newline, so drop these
unnecessary additional newlines.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
the rtl: or RTL: prefix in the string is pointless. The rtl_dev_* macros
already does that.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is used to print fw version for debug convenience
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Realtek Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When SoC receives pre shut down command, it share the same
with other COEX shared clients. So SoC needs a short time
after sending VS pre shutdown command before turning off
the regulators and sending the power off pulse. Along with
short delay, needs to wait for command complete event for
Pre shutdown VS command
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some supported devices need more time to come out of reset (eg.
BCM4345C5 in AP6256).
I don't have/found a datasheet, so the value was arrive at
experimentally with the Oprange Pi 3 board. Without increased delay,
I got intermittent failures during probe. This is a Bluetooth 5.0
device, so maybe that's why it takes longer to initialize than the
others.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is present in the AP6526 WiFi/Bluetooth 5.0 module.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA UART Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Static structure qca_proto, of type hci_uart_proto, is used four times:
as the last argument in function hci_uart_register_device(), and as the
only argument to functions hci_uart_register_proto() and
hci_uart_unregister_proto(). In all three of these functions, the
parameter corresponding to qca_proto is declared as constant. Therefore,
make qca_proto itself constant as well in order to protect it from
unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Static variable header_ops, of type header_ops, is used only once, when
it is assigned to field header_ops of a variable having type net_device.
This corresponding field is declared as const in the definition of
net_device. Hence make header_ops constant as well to protect it from
unnecessary modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
From the perspective of controller, global suspend means there is no
SET_FEATURE (DEVICE_REMOTE_WAKEUP) and controller would drop the
firmware. It would consume less power. So we should not send this kind
of SET_FEATURE when host goes to suspend state.
Otherwise, when making device enter selective suspend, host should send
SET_FEATURE to make sure the firmware remains.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If CONFIG_ACPI is not set, gcc warn this:
drivers/bluetooth/hci_bcm.c:831:39: warning:
acpi_bcm_int_last_gpios defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:838:39: warning:
acpi_bcm_int_first_gpios defined but not used [-Wunused-const-variable=]
move them to #ifdef CONFIG_ACPI block.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The qca_data structure is allocated with kzalloc() and hence
zero-initialized. Remove a bunch of unnecessary explicit
initializations of struct members to zero.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Changes made to add support for fast advertising interval
as per core 4.1 specification, section 9.3.11.2.
A peripheral device entering any of the following GAP modes and
sending either non-connectable advertising events or scannable
undirected advertising events should use adv_fast_interval2
(100ms - 150ms) for adv_fast_period(30s).
- Non-Discoverable Mode
- Non-Connectable Mode
- Limited Discoverable Mode
- General Discoverable Mode
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ice_parse_caps is printing capabilities in a different way when
compared to the variable names. This makes it difficult to search for
the right strings in the debug logs. So this patch updates the
print strings to be exactly the same as the fields' name in the
structure.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver should start out with a reasonable number of descriptors that
can prevent drops due to a CPU being in a power management state.
Change the default number of descriptors to 2048.
The user can always change the value at runtime. Transmit descriptor
counts are not modified because they don't need to change due to the
speed of the interface, or for power managed CPUs, but the code is
simplified to a fixed value for the transmit default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove q_left_tx and q_left_rx from the PF struct as these can be
obtained by calling ice_get_avail_txq_count and ice_get_avail_rxq_count
respectively.
The function ice_determine_q_usage is only setting num_lan_tx and
num_lan_rx in the PF structure, and these are later assigned to
vsi->alloc_txq and vsi->alloc_rxq respectively. This is an unnecessary
indirection, so remove ice_determine_q_usage and just assign values
for vsi->alloc_txq and vsi->alloc_rxq in ice_vsi_set_num_qs and use
these to set num_lan_tx and num_lan_rx respectively.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an additional boolean parameter to the ice_init_dcb
function. This boolean controls if the LLDP MIB change
events are registered for. Also, add a new function
defined ice_cfg_lldp_mib_change. The additional function
is necessary to be able to register for LLDP MIB change
events after calling ice_init_dcb. The net effect of these
two changes is to allow a delayed registration for MIB change
events so that the driver is not accepting events before it
is ready for them.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add internal usage flag, bit 91 as described in spec.
Update width of internal queue state to 122 also as described in spec.
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes how and when the driver report link status, instead of
waiting till the call to enable queues for VF, we should report link
status earlier with opcode to get VF resources - So as to avoid reporting
erroneous information, especially when queues have not been configured.
In addition, we can also make a call to get and report link status change
after when queue is enabled, at least to report netdev or PHY link status.
This is in accordance to how link speed is being reported for PF...
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check the ICE_FLAG_DCB_CAPABLE before calling ice_init_pf_dcb.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is port of a fix from i40e commit 2ad1274fa3 ("i40e: don't
report link up for a VF who hasn't enabled queues")
Older VF drivers do not respond well to receiving a link
up notification before queues are enabled. This can cause their state
machine to think that it is safe to send traffic. This results in a Tx
hang on the VF.
Record whether the PF has actually enabled queues for the VF. When
reporting link status, always report link down if the queues aren't
enabled. In this way, the VF driver will never receive a link up
notification until after its queues are enabled.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a PFR (or bigger reset) occurs, the device clears the VF_MBX_ARQLEN
register for all VFs. But if a VFR is triggered by a VF, the device does
NOT clear this register, and the VF driver will never see the reset.
When this happens, the VF driver will eventually timeout and attempt
recovery, and usually it will be successful. But this makes resets take
a long time and there are occasional failures.
We cannot just blithely clear this register on every reset; this has
been shown to cause synchronization problems when a PFR is triggered
with a large number of VFs.
Fix this by clearing VF_MBX_ARQLEN when the reset source is not PFR.
GlobR will trigger PFR, so this test catches that occurrence as well.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver has supported a transmit work limit
that was configurable from ethtool for a long time, but
there are no good use cases for having it be a variable
that can be changed at run time. In addition, this
variable was noted to be causing performance overhead
due to cache misses.
Just remove the variable and let the code use a constant
so that the functionality is maintained (a limit on the
number of transmits that will be cleaned in any one call
to the clean routines) without the cache miss.
Removes code, removes a variable, removes testing surface. Yay.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a small bit of efficiency to the code by adding a
prefetch of the port_info structure in order to help
avoid a cache miss a little later on in execution.
Also add an unlikely statement to a branch which
generally will never happen in normal operation.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a simple patch to move the assignment to a local variable
closer to the site where the local variable is used. This
can help readability and also maybe performance, although the
performance enhancement is really dependent upon the compiler.
No functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a couple of functions that don't need two arguments
passed in when the second argument already had access to
the pointer pointed to by the first.
Remove the unnecessary arguments.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_sched_get_tc_node uses pi->root without checking for NULL. Add a
check to prevent NULL pointer dereference.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are multiple places where we currently use ice_find_vsi_by_type
to get the PF (a.k.a. main) VSI. The PF VSI by definition is always
the first element in the pf->vsi array (i.e. pf->vsi[0]). So instead
add and use a new helper function ice_get_main_vsi, which just returns
pf->vsi[0].
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when vsi->req_txqs or vsi->req_rxqs are set we don't
correctly set the number of vsi->num_q_vectors. Fix this by
setting the number of queue vectors based on the max
between the vsi->alloc_txqs and vsi->alloc_rxqs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Björn Töpel says:
====================
This is a four patch series of various barrier, {READ, WRITE}_ONCE
cleanups in the AF_XDP socket code. More details can be found in the
corresponding commit message. Previous revisions: v1 [4] and v2 [5].
For an AF_XDP socket, most control plane operations are done under the
control mutex (struct xdp_sock, mutex), but there are some places
where members of the struct is read outside the control mutex. The
dev, queue_id members are set in bind() and cleared at cleanup. The
umem, fq, cq, tx, rx, and state member are all assigned in various
places, e.g. bind() and setsockopt(). When the members are assigned,
they are protected by the control mutex, but since they are read
outside the mutex, a WRITE_ONCE is required to avoid store-tearing on
the read-side.
Prior the state variable was introduced by Ilya, the dev member was
used to determine whether the socket was bound or not. However, when
dev was read, proper SMP barriers and READ_ONCE were missing. In order
to address the missing barriers and READ_ONCE, we start using the
state variable as a point of synchronization. The state member
read/write is paired with proper SMP barriers, and from this follows
that the members described above does not need READ_ONCE statements if
used in conjunction with state check.
To summarize: The members struct xdp_sock members dev, queue_id, umem,
fq, cq, tx, rx, and state were read lock-less, with incorrect barriers
and missing {READ, WRITE}_ONCE. After this series umem, fq, cq, tx,
rx, and state are read lock-less. When these members are updated,
WRITE_ONCE is used. When read, READ_ONCE are only used when read
outside the control mutex (e.g. mmap) or, not synchronized with the
state member (XSK_BOUND plus smp_rmb())
[1] https://lore.kernel.org/bpf/beef16bb-a09b-40f1-7dd0-c323b4b89b17@iogearbox.net/
[2] https://lwn.net/Articles/793253/
[3] https://github.com/google/ktsan/wiki/READ_ONCE-and-WRITE_ONCE
[4] https://lore.kernel.org/bpf/20190822091306.20581-1-bjorn.topel@gmail.com/
[5] https://lore.kernel.org/bpf/20190826061053.15996-1-bjorn.topel@gmail.com/
v2->v3:
Minor restructure of commits.
Improve cover and commit messages. (Daniel)
v1->v2:
Removed redundant dev check. (Jonathan)
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
