Patch removes printk and place em28xx_errdev macros to provide
information about driver name to dmesg.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Essentially if a snd_em28xx_capture_trigger() stop followed by a snd_em28xx_capture_trigger() start would not yield any
data because there was some logic put in with an adev->shutdown variable which did not seem warranted in my humble opinion.
It would cause snd_em28xx_capture_trigger start never to start up the audio stream until the device was closed and
reopened again. Upon re-opening the device adev->shutdown is reset and audio data would again flow.
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for em28xx memory leak and function rename
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed bad check. Thanks to Robert Krakora <rob.krakora@messagenetsystems.com>
to report that.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kaiomy entry.
Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one
of those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For i2c normal work, we need to slow down the bus speed. However, the
slow down breaks the eeprom firmware load. So, use normal speed for
eeprom booting and then restore the i2c speed after that.
It should also be noticed that no other I2C transfer should be in course
while booting from eeprom, otherwise, tda10046 goes into an instable
state. So, proper locking are needed at the i2c bus master.
Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom
with firmware version 29.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
KBL is not needed on saa7134, so, let's remove it.
However, we should take some care to avoid opening the module while
initializing it. This issue exists with newer udev's that opens a device
as soon as the driver is registered. So, a proper lock is needed on
open.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix two broken controls where a step weren't specified. Without a step,
userspace apps won't allow to adjust such controls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some saa7134 devices require to open an i2c gate before tuning. This
patch fix the initialization for those devices.
The nxt200x_gate_ctrl() logic were returned back to the old place, since
we don't know how to close the gate. A future pacth could revert that
change and provide the proper close gate control, to avoid keeping it
open forever.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On certain devices, before opening a tuner, we need to open the tuner
gate via i2c.
This patch just moves the tuner probing code to the same place where
such i2c commands are handled, to make easier to fix this trouble on
later patches.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, be sure that gate will be kept disabled if an error occurs.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gate control logic is broken: several routines just keep it open;
other rotines close it properly; there are even other routines that
assumes that it is open without really checking or opening it.
Instead of having to manually handle the gate control and having such
troubles, let a sub-routine take care of the gate, opening it before
i2c_transfer and closing it after that. This avoids leaving the gate
into a random state.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Doing the v4l2_device registration in the saa7146 core will make it
dependent on v4l2, even for DVB-only boards. This registration and
unregistration belongs in saa7146_vv instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified mxb to load the i2c modules through v4l2_subdev. So no more probing.
Modified tea6415c and tea6420 to use the standard routing ops to do the
routing, rather than using private commands. Dropped the private commands
from tda9840 (they were never used except during initialization of the
module).
Added saa7146 support for VIDIOC_DBG_G_CHIP_IDENT.
Converted saa5246a and saa5249 to v4l2_subdev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that implement this always have to set the ident and revision
to V4L2_IDENT_NONE and 0. Do this in the v4l2 core so drivers don't have
to do this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use consistent naming for pci_dev, v4l2_device and video_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The raw video device didn't report the image size correctly.
When setting a new image the image height has to be a multiple of 32 lines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Place usb_make_path in radio-si470x.c that used when reporting bus_info
information in vidioc_querycap.
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch corrects checking of returned value after usb_bulk_msg. Now we
also check if number of transferred bytes equals to BUFFER_LENGTH.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase driver version to 0.10, remove old and add new useful comments.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch introduces new amradio_set_stereo function.
Driver calls this func to make stereo radio reception.
Corrects checking of returned value after usb_bulk_msg.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixing frequency adjustment to provide better diapason(band?) fit.
Also, add AMRADIO_SET_FREQ to the list of commands.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch introduces new amradio_set_mute function. Amradio_start and
amradio_stop removed. This makes driver more flexible and it's useful
for next changes.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There should be dev_err message if video_register_device() fails.
Correct this situation.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add MC44S803 support to AF9015 driver.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sliced VBI, in the manner that ivtv implements it as a separate data stream,
now works for 525 line 60 Hz systems like NTSC-M. It may work for 625 line
50 Hz systems, but I have more engineering work to do, to verify it is operating
properly. Sliced data insertion into the MPEG PS should be working, but is
untested.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx23418 appears to send Raw VBI buffers with a PTS on a per frame
basis, not per field, so process Raw VBI on a whole frame basis and reduce
some complexity. Fix VBI buffer size computation to handle a whole
frame of Raw VBI for a 625 line system, which is the worst case and will
work for 525 lines systems as well.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed an endianess problem with the collection of the PTS from
the VBI buffer given to us by the encoder. Also extrapolated the
last 12 bytes of the last line of each field, to remove artifacts
created by removing the first 12 bytes of each field for raw VBI.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver was incorrectly setting 0 line counts in a firmware
API call to set the maximum amount of lines per field.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Encoder will only allow the Raw VBI parameters, along with a number of
other API parameters, to take effect when no analog captures are in
progress. These parameters must be set before the first analog capture starts,
be it MPEG, VBI, YUV, etc., and cannot be changed until the last one stops. It
is not obvious to me what capture channel API parameters are shared and which
ones must be set per capture channel, so set them all for every analog
capture channel start up. This fixes the driver so that VBI capture can be
started up after the MPEG capture is going.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
More sliced VBI fixes to bring the cx18 driver closer to full V4L2 spec
compliance for VBI and to get sliced VBI working better.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The old code from ivtv used a CX23415/6 PTS, which was simply left at 0 in the
cx18 driver. Since the CX23418 gives us what I think is a PTS (or some other
90 kHz clock count) with each VBI buffer, this change has the cx18 driver use
that as a PTS.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX18_AUDIO_ENABLE register usually never reads back what was just written
under normal circumstances. Perform better checking that a write went to the
register as expected with a specification of what bits to verify.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also enables the autogain for the mt9v111.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mi1310_soc sequences come from the ms-win driver C0130Dev.inf.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Data debug for i2c transactions was provided by the functions
called by dib0700_i2c_xfer_legacy, but not dib0700_i2c_xfer_new.
This patch adds the missing data debug dumps to dib0700_i2c_xfer_new.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some cards uses cx24116 LNB_DC pin for LNB power control,
some not uses, some uses it different way, like HVR-4000.
Tested-by : Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_DRIVERIDs are phased out. Remove those that are unused at the moment.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A hue of -128 was rejected due to an incorrect range check, which was
faithfully copy-and-pasted into four drivers...
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most boards nowadays supports saa7134-alsa. Even some of they doesn't have any
option to wire an audio cable. So, lets load saa7134-alsa by default, if the
board is not based on saa7130 and if saa7134-alsa is compiled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
saa7134: Fix tuner access on Kworld ATSC110
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is a patch which adds some documentation about meanings of the
the lnbp21 system register bits.
Signed-off-by: Hans Werner <hwerner4@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lack of the green color is fixed by sensor sequences closer to the
ms-win traces.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcams worked only one time after connection.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the wrong clock value, the image had two moving colored lines.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bugs were in the first init sequence of the sensor.
The rewrite is adapted from a ms-win trace.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for USB webcams based on the MR97310A chip. It was
tested with an Aiptek PenCam VGA+ webcam.
Signed-off-by: Kyle Guinn <elyk03@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The returned value of i2c read is a 16 bits word. It was stored in
a 8 bits variable, preventing a sensor to be detected.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Hercules webcam based on ov534 use different sensor than Playstation Eye,
disable them until full support is provided.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam is generic and some sensors are not treated by
the driver zc0301.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The err, warning and info redefinitions don't need the use of
do {} while.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce int ret and check it value after call to usb_register().
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The transfer endpoint address is now automatically chosen.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new Avermedia Volar-X is shipped with a new remote(RM-KS). The attached
patch add a new option to the remote parameter of dvb_usb_af9015 for this
remote.
Signed-off-by: Felipe Morales Moreno <felipe.morales.moreno@gmail.com>
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove dual_mode module param. Possible 2nd FE seems not to be buggy
any more and therefore can be enabled as default.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just call em28xx_isoc_audio_deinit() if em28xx sent a usb_submit().
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added entry for GADMEI TVR200.
Thanks to Yohanes Nugroho <yohanes@gmail.com> for testing and data collection.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it clear that a failure in dib0700_i2c_enumeration is a fatal condition
and we cannot continue. If the failure occurs, do not attempt to attach to
the tuner.
Problem Noticed the issue when debugging an i2c issue a YUAN High-Tech
STK7700PH for user Roshan Karki <roshan@olenepal.org>.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it clear that the address is in hex format.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds the IR data structure to the configuration datastructure of the
Hauppauge WinTV Nova-TD USB stick (52009)
Provided remote control is the same as theone provided with the Nova-T500
Card.
Signed-off-by: Arne Luehrs <arne.luehrs@googlemail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Place usb_make_path in dsbr100.c, radio-mr800.c, radio-si470x.c that
used when reporting bus_info information in vidioc_querycap.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous conversion to video_ioctl2 broke VIDIOC_ENUMSTD. This
is now fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a free-without-alloc bug for V4L2_MEMORY_USERPTR
video buffers.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's a quad Bt878 PCI-e x1 capture board that's basically the same as the
IVC-200 (quad Bt878 PCI) capture board that's currently supported in
the V4L2 bttv driver.
Manufacturer's web page for IVCE-8784 with photo and info:
http://www.iei.com.tw/en/product_IPC.asp?model=IVCE-8784
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch removes err() macros from few usb devices.
It places pr_err in pvrusb2-v4l2.c, dev_err in dabusb and in usbvision
drivers. Beside placing dev_err, patch defines new s2255_dev_err macro
with S2255_DRIVER_NAME in s2255 module.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Thierry Merle <thierry.merle@free.fr>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dynamically allocated input_dev->phys buffer isn't freed when
unregistering the device. As the input layer doesn't provide any release
callback, use a fixed-size buffer inside the uvc_device structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
URB buffers for video transfers are sized to UVC_MAX_PACKETS bulk/isochronous
packets by default. If the system is too low on memory try successively
smaller numbers of packets until allocation succeeds.
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Alcor Micro AU3820 chipset (found in the Future Boy PC USB webcam)
requires the MINMAX quirk. Add a corresponding entry in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
strncpy is unsafe as it doesn't append a terminating NUL character when the
source string doesn't fit in the destination buffer. Replace it with strlcpy.
strncat is misused as its size argument refers to the source string, not the
destination buffer. Replace it with strlcat.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID 1b80:e39b for KWorld DVB-T 395U. This device revision does
have Quantek QT1010 silicon tuner.
Thanks-to: Ray Chen <swyear@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
request_module() needs to be called with a string literal for a
format string or with 1 or more variable arguments to avoid
compiler warnings and possible exploits, if someone could cause
us to get a format string with a '%' code in the format string
when we make the call.
Reported-by: Brandon Jenkins <bcjenkins@tvwhere.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
First step in conversion to the new V4L2 framework. Added per cx18 device
instance of the v4l2_device and its registration.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
