Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.
In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.
With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.
Changes in v2:
- From Mark Brown review:
- Replaced some if branches with switch statements
- Moved irq get and request in probe function
- Changed short conditionals to full ones
- Removed useless check for ocp_irq_requested
- Fixed issues with YAML documentation
AngeloGioacchino Del Regno (7):
regulator: qcom-labibb: Implement voltage selector ops
regulator: qcom-labibb: Implement current limiting
regulator: qcom-labibb: Implement pull-down, softstart, active
discharge
dt-bindings: regulator: qcom-labibb: Document soft start properties
regulator: qcom-labibb: Implement short-circuit and over-current IRQs
dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP
.../regulator/qcom-labibb-regulator.yaml | 30 +-
arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 +-
drivers/regulator/qcom-labibb-regulator.c | 661 +++++++++++++++++-
3 files changed, 686 insertions(+), 13 deletions(-)
--
2.29.2
Implement {get,set}_voltage_sel, list_voltage, map_voltage with
the useful regulator regmap helpers in order to be able to manage
the voltage of LAB (positive) and IBB (negative) regulators.
In particular, the supported ranges are the following:
- LAB (pos): 4600mV to 6100mV with 100mV stepping,
- IBB (neg): -7700mV to -1400mV with 100mV stepping.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210113194214.522238-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the ternary condition which is a bad coding style
in the kernel
I also remove the defering configuration of the nxp,phase-shift.
The configuration is now done at parsing time. It save some memory
and it's better for comprehension.
I also use the OTP default configuration when the parameter is wrong
or not specified.
I think that it's better to use the default configuration from the chip
than an arbitrary value.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-7-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.
As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-5-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform data header was only used to pass platform
data from board files. We now populate the regulators
exclusively from device tree, so the header contents can
be moved into the regulator drivers.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct ab8500_regulator_platform_data was a leftover
since the days before we probed all regulators from the
device tree. The ab8500-ext regulator was the only used,
defining platform data and register intialization that
was never used for anything, a copy of a boardfile no
longer in use.
Delete the ab8500_regulator_platform_data and make the
ab8500-ext regulator reference the regulator init data
in the local file directly. We are 100% device tree
these days.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
This patch makes the LPM pin as optional as this may be controlled
in the last phase of suspend procedure to decrease the power consumption
while suspended. Along w/ this update the MAINTAINERS entry for this
driver.
Thank you,
Claudiu Beznea
Claudiu Beznea (3):
dt-bindings: regulator: mcp16502: document lpm as optional
regulator: mcp16502: lpm pin can be optional on some platforms
MAINTAINERS: add myself as maintainer for mcp16502
Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt | 3 ++-
MAINTAINERS | 4 ++--
drivers/regulator/mcp16502.c | 2 +-
3 files changed, 5 insertions(+), 4 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The ROHM PMIC regulator drivers only need the regmap pointer from
the parent device. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210107122355.GA35080@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platform (e.g. SAMA7G5) LPM pin should be optional as it can
be controlled explicitly (via shutdown controller registers) in the
platform specific power saving code to decrease the power consumption
while suspended as this SoC pin may be connected to other devices that
could take power saving actions based on its value.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1610028927-9842-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series is based on v5.10-rc1.
The patchsets add support for MediaTek hardware module named DVFSRC
(dynamic voltage and frequency scaling resource collector). The DVFSRC is
a HW module which is used to collect all the requests from both software
and hardware and turn into the decision of minimum operating voltage and
minimum DRAM frequency to fulfill those requests.
So, This series is to implement the dvfsrc driver to collect all the
requests of operating voltage or DRAM bandwidth from other device drivers
likes GPU/Camera through 3 frameworks basically:
1. interconnect framework: to aggregate the bandwidth
requirements from different clients
[1] https://patchwork.kernel.org/cover/10766329/
There has a hw module "DRAM scheduler", which used to control the throughput.
The DVFSRC will collect forecast data of dram bandwidth from
SW consumers(camera/gpu...), and according the forecast to change the DRAM
frequency
2. Regualtor framework: to handle the operating voltage requirement from user or
cosumer which not belong any power domain
Changes in V6:
* Remove the performace state support, because the request from consumer can be
replaced by using interconnect and regulator framework.
* Update the DT patches and convert them to DT schema. (Georgi)
* Modify the comment format and coding style. (Mark)
Changes in V5:
* Support more platform mt6873/mt8192
* Drop the compatible and interconnect provider node and make the parent node an
interconnect provider. (Rob/Georgi)
* Make modification of interconnect driver from coding suggestion. (Georgi)
* Move interconnect diagram into the commit text of patch. (Georgi)
* Register the interconnect provider as a platform sub-device. (Georgi)
Changes in V4:
* Add acked TAG on dt-bindings patches. (Rob)
* Declaration of emi_icc_aggregate since the prototype of aggregate function
has changed meanwhile. (Georgi)
* Used emi_icc_remove instead of icc_provider_del on probe. (Georgi)
* Add dvfsrc regulator driver into series.
* Bug fixed of mt8183_get_current_level.
* Add mutex protection for pstate operation on dvfsrc_set_performance.
Changes in V3:
* Remove RFC from the subject prefix of the series
* Combine dt-binding patch and move interconnect dt-binding document into
dvfsrc. (Rob)
* Remove unused header, add unit descirption to the bandwidth, rename compatible
name on interconnect driver. (Georgi)
* Fixed some coding style: check flow, naming, used readx_poll_timeout
on dvfsrc driver. (Ryan)
* Rename interconnect driver mt8183.c to mtk-emi.c
* Rename interconnect header mtk,mt8183.h to mtk,emi.h
* mtk-scpsys.c: Add opp table check first to avoid OF runtime parse failed
Changes in RFC V2:
* Remove the DT property dram_type. (Rob)
* Used generic dts property 'opp-level' to get the performace state. (Stephen)
* Remove unecessary dependency config on Kconfig. (Stephen)
* Remove unused header file, fixed some coding style issue, typo,
error handling on dvfsrc driver. (Nicolas/Stephen)
* Remove irq handler on dvfsrc driver. (Stephen)
* Remove init table on dvfsrc driver, combine hw init on trustzone.
* Add interconnect support of mt8183 to aggregate the emi bandwidth.
(Georgi)
V5: https://patchwork.kernel.org/project/linux-mediatek/list/?series=348065
V4: https://lore.kernel.org/patchwork/cover/1209284/
V3: https://patchwork.kernel.org/cover/11118867/
RFC V2: https://lore.kernel.org/patchwork/patch/1068113/
RFC V1: https://lore.kernel.org/patchwork/cover/1028535/
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The ROHM PMIC regulator drivers only need the regmap pointer from
the parent device. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210105130221.GA3438042@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver for regulators exposed by the DVFSRC (dynamic voltage and
frequency scaling resource collector) found in devices based on
mt8183 and newer platforms.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Link: https://lore.kernel.org/r/1608790134-27425-12-git-send-email-henryc.chen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PM8009 has special revision (P=1), which is to be used for sm8250
platform. The major difference is the S2 regulator which supplies 0.95 V
instead of 2.848V. Declare regulators data to be used for this chip
revision. The datasheet calls the chip just pm8009-1, so use the same
name.
base-commit: 5c8fe583cc
The function regulator_set_device_supply() is referenced a few times in
comments in regulator/core.c; however this function was removed a long
time ago by commit a5766f11cf ("regulator: core - Rework machine API to
remove string based functions."). Update those references to point to
set_consumer_device_supply(), which replaced the old function.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20210103165541.784360-1-djrscally@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A built-in regulator driver cannot link against a modular cmd_db driver:
qcom-rpmh-regulator.c:(.text+0x174): undefined reference to `cmd_db_read_addr'
There is already a dependency for RPMh, so add another one of this
type for cmd_db.
Fixes: 34c5aa2666 ("regulator: Kconfig: Fix REGULATOR_QCOM_RPMH dependencies to avoid build error")
Fixes: 46fc033eba ("regulator: add QCOM RPMh regulator driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201230145712.3133110-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
PM8009 has special revision (P=1), which is to be used for sm8250
platform. The major difference is the S2 regulator which supplies 0.95 V
instead of 2.848V. Declare regulators data to be used for this chip
revision. The datasheet calls the chip just pm8009-1, so use the same
name.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 06369bcc15 ("regulator: qcom-rpmh: Add support for SM8150")
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201231122348.637917-4-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet pm8009's HFS515 regulators have 16mV
resolution rather than declared 1.6 mV. Correct the resolution.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 06369bcc15 ("regulator: qcom-rpmh: Add support for SM8150")
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201231122348.637917-3-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the DC-DC converters and LDO regulators found in
the ATC2603C and ATC2609A chip variants of the Actions Semi ATC260x
family of PMICs.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Link: https://lore.kernel.org/r/1117b1a01b3948446cb3cc407e52de3a5d4212b0.1609258905.git.cristian.ciocaltea@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Restrict REGULATOR_QCOM_RPMH to QCOM_COMMAND_DB it the latter is enabled.
Fixes this build error:
microblaze-linux-ld: drivers/regulator/qcom-rpmh-regulator.o: in function `rpmh_regulator_probe':
(.text+0x354): undefined reference to `cmd_db_read_addr'
Fixes: 778279f4f5 ("soc: qcom: cmd-db: allow loading as a module")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Link: https://lore.kernel.org/r/20201225185004.20747-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the typical startup times from the data sheet so boards get a
reasonable default. Not setting any enable time can lead to board hangs
when e.g. clocks are enabled too soon afterwards.
This fixes gpu power domain resume on the Librem 5.
[Moved #defines into driver, seems to be general agreement and avoids any
cross tree issues -- broonie]
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/41fb2ed19f584f138336344e2297ae7301f72b75.1608316658.git.agx@sigxcpu.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The pf8x00 driver supports three devices, the DT compatible strings
and I2C IDs should enumerate these specifically rather than using a
wildcard so that we don't collide with anything incompatible in the
same ID range in the future and so that we can handle any software
visible differences between the variants we find.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201215132024.13356-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201210212748.5849-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add proper modalias structures to let this driver load automatically if
compiled as module, because max14577 MFD driver creates MFD cells with
such compatible strings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210112139.5370-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes a couple of bugs in the DA9121 driver.
One in an uninialised string I forgot to remove when changing to of_parse_cb()
The other is an index for an optional DT property which overflows
Adam Ward (2):
regulator: da9121: Remove uninitialised string variable
regulator: da9121: Fix index used for DT property
drivers/regulator/da9121-regulator.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
--
1.9.1
There is a missing "return ret;" on this error path so we call
"da9121_check_device_type(i2c, chip);" which will end up dereferencing
"chip->regmap" and lead to an Oops.
Fixes: c860476b9e ("regulator: da9121: Add device variant regmaps")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/X85soGKnWAjPUA7a@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
When I use the axp20x chip to power my SDIO device on the 5.4 kernel,
the output voltage of DLDO2 is wrong. After comparing the register
manual and source code of the chip, I found that the mask bit of the
driver register of the port was wrong. I fixed this error by modifying
the mask register of the source code. This error seems to be a copy
error of the macro when writing the code. Now the voltage output of
the DLDO2 port of axp20x is correct. My development environment is
Allwinner A40I of arm architecture, and the kernel version is 5.4.
Signed-off-by: DingHua Ma <dinghua.ma.sz@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org>
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Link: https://lore.kernel.org/r/20201201001000.22302-1-dinghua.ma.sz@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support from RPMH regulators found in PM8350 and PM8350c PMICs
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201203071244.2652297-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_GPIOLIB is disabled, the declarations from linux/gpio/consumer.h
are not visible:
drivers/regulator/da9121-regulator.c:371:14: error: implicit declaration of function 'fwnode_gpiod_get_index' [-Werror,-Wimplicit-function-declaration]
ena_gpiod = fwnode_gpiod_get_index(of_fwnode_handle(np), "enable", 0,
^
drivers/regulator/da9121-regulator.c:372:7: error: use of undeclared identifier 'GPIOD_OUT_HIGH'
GPIOD_OUT_HIGH |
^
drivers/regulator/da9121-regulator.c:373:7: error: use of undeclared identifier 'GPIOD_FLAGS_BIT_NONEXCLUSIVE'
GPIOD_FLAGS_BIT_NONEXCLUSIVE,
Include this explicitly to help compile testing.
Fixes: 46c413d5bb ("regulator: da9121: Add support for device variants via devicetree")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201204165229.3754763-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following sparse warnings:
drivers/regulator/da9121-regulator.c:55:21: warning: symbol 'da9121_10A_2phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:63:21: warning: symbol 'da9121_6A_2phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:71:21: warning: symbol 'da9121_5A_1phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:79:21: warning: symbol 'da9121_3A_1phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:151:32: warning: symbol 'status_event_handling' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/1606994795-36182-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds interrupt handler for variants, and notifications for events; over
temperature/voltage/current. Because the IRQs are triggered by persisting
status, they must be masked and the status polled until clear, before the
IRQ can be enabled again.
Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/fe21796bbcbadff84a472a4cc581ae8fafc7f8f5.1606755367.git.Adam.Ward.opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
