Commit Graph

4699 Commits

Author SHA1 Message Date
Masahiro Yamada
e73a3896ea mmc: sdhci-cadence: enable v4_mode to fix ADMA 64-bit addressing
The IP datasheet says this controller is compatible with SD Host
Specification Version v4.00.

As it turned out, the ADMA of this IP does not work with 64-bit mode
when it is in the Version 3.00 compatible mode; it understands the
old 64-bit descriptor table (as defined in SDHCI v2), but the ADMA
System Address Register (SDHCI_ADMA_ADDRESS) cannot point to the
64-bit address.

I noticed this issue only after commit bd2e75633c ("dma-contiguous:
use fallback alloc_pages for single pages"). Prior to that commit,
dma_set_mask_and_coherent() returned the dma address that fits in
32-bit range, at least for the default arm64 configuration
(arch/arm64/configs/defconfig). Now the host->adma_addr exceeds the
32-bit limit, causing the real problem for the Socionext SoCs.
(As a side-note, I was also able to reproduce the issue for older
kernels by turning off CONFIG_DMA_CMA.)

Call sdhci_enable_v4_mode() to fix this.

Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-30 09:17:53 +02:00
Chunyan Zhang
2f765c175e mmc: sdhci-sprd: clear the UHS-I modes read from registers
sprd's sd host controller supports SDR50/SDR104/DDR50 though, the UHS-I
mode used by the specific card can be selected via devicetree only.

Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-30 09:17:53 +02:00
Chunyan Zhang
4324e54bbe mms: sdhci-sprd: add SDHCI_QUIRK_BROKEN_CARD_DETECTION
sprd's sd host controller doesn't support detection to
card insert or remove.

Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-30 09:17:53 +02:00
Chunyan Zhang
6a526f66ab mmc: sdhci-sprd: add SDHCI_QUIRK2_PRESET_VALUE_BROKEN
The bit of PRESET_VAL_ENABLE in HOST_CONTROL2 register is reserved on
sprd's sd host controller, set quirk2 to disable configuring this.

Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-30 09:17:53 +02:00
Chunyan Zhang
4eae8cbdff mmc: sdhci-sprd: add get_ro hook function
sprd's sd host controller doesn't support write protect to sd card.

Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-30 09:17:53 +02:00
Chunyan Zhang
efdaf27517 mmc: sdhci-sprd: fixed incorrect clock divider
The register SDHCI_CLOCK_CONTROL should be cleared before config clock
divider, otherwise the frequency configured maybe lower than we
expected.

Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-30 09:17:53 +02:00
Eugen Hristev
7871aa60ae mmc: sdhci-of-at91: add quirk for broken HS200
HS200 is not implemented in the driver, but the controller claims it
through caps. Remove it via a quirk, to make sure the mmc core do not try
to enable HS200, as it causes the eMMC initialization to fail.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-22 13:49:40 +02:00
Dmitry Osipenko
0f686ca933 Revert "mmc: sdhci-tegra: drop ->get_ro() implementation"
The WRITE_PROTECT bit is always in a "protected mode" on Tegra and
WP-GPIO state need to be used instead. In a case of the GPIO absence,
write-enable should be assumed. External SD is writable once again as
a result of this patch because the offending commit changed behaviour for
the case of a missing WP-GPIO to fall back to WRITE_PROTECT bit-checking,
which is incorrect for Tegra.

Cc: stable@vger.kernel.org # v5.1+
Fixes: e8391453e2 ("mmc: sdhci-tegra: drop ->get_ro() implementation")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-21 14:48:30 +02:00
Kevin Hao
b803974a86 mmc: cavium: Add the missing dma unmap when the dma has finished.
This fixes the below calltrace when the CONFIG_DMA_API_DEBUG is enabled.
  DMA-API: thunderx_mmc 0000:01:01.4: cpu touching an active dma mapped cacheline [cln=0x000000002fdf9800]
  WARNING: CPU: 21 PID: 1 at kernel/dma/debug.c:596 debug_dma_assert_idle+0x1f8/0x270
  Modules linked in:
  CPU: 21 PID: 1 Comm: init Not tainted 5.3.0-rc1-next-20190725-yocto-standard+ #64
  Hardware name: Marvell OcteonTX CN96XX board (DT)
  pstate: 80400009 (Nzcv daif +PAN -UAO)
  pc : debug_dma_assert_idle+0x1f8/0x270
  lr : debug_dma_assert_idle+0x1f8/0x270
  sp : ffff0000113cfc10
  x29: ffff0000113cfc10 x28: 0000ffff8c880000
  x27: ffff800bc72a0000 x26: ffff000010ff8000
  x25: ffff000010ff8940 x24: ffff000010ff8968
  x23: 0000000000000000 x22: ffff000010e83700
  x21: ffff000010ea2000 x20: ffff000010e835c8
  x19: ffff800bc2c73300 x18: ffffffffffffffff
  x17: 0000000000000000 x16: 0000000000000000
  x15: ffff000010e835c8 x14: 6d20616d64206576
  x13: 69746361206e6120 x12: 676e696863756f74
  x11: 20757063203a342e x10: 31303a31303a3030
  x9 : 303020636d6d5f78 x8 : 3230303030303030
  x7 : 00000000000002fd x6 : ffff000010fd57d0
  x5 : 0000000000000000 x4 : ffff0000106c5210
  x3 : 00000000ffffffff x2 : 0000800bee9c0000
  x1 : 57d5843f4aa62800 x0 : 0000000000000000
  Call trace:
   debug_dma_assert_idle+0x1f8/0x270
   wp_page_copy+0xb0/0x688
   do_wp_page+0xa8/0x5b8
   __handle_mm_fault+0x600/0xd00
   handle_mm_fault+0x118/0x1e8
   do_page_fault+0x200/0x500
   do_mem_abort+0x50/0xb0
   el0_da+0x20/0x24
  ---[ end trace a005534bd23e109f ]---
  DMA-API: Mapped at:
   debug_dma_map_sg+0x94/0x350
   cvm_mmc_request+0x3c4/0x988
   __mmc_start_request+0x9c/0x1f8
   mmc_start_request+0x7c/0xb0
   mmc_blk_mq_issue_rq+0x5c4/0x7b8

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Fixes: ba3869ff32 ("mmc: cavium: Add core MMC driver for Cavium SOCs")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-06 18:59:14 +02:00
Kevin Hao
fa25eba699 mmc: cavium: Set the correct dma max segment size for mmc_host
We have set the mmc_host.max_seg_size to 8M, but the dma max segment
size of PCI device is set to 64K by default in function pci_device_add().
The mmc_host.max_seg_size is used to set the max segment size of
the blk queue. Then this mismatch will trigger a calltrace like below
when a bigger than 64K segment request arrives at mmc dev. So we should
consider the limitation of the cvm_mmc_host when setting the
mmc_host.max_seg_size.
  DMA-API: thunderx_mmc 0000:01:01.4: mapping sg segment longer than device claims to support [len=131072] [max=65536]
  WARNING: CPU: 6 PID: 238 at kernel/dma/debug.c:1221 debug_dma_map_sg+0x2b8/0x350
  Modules linked in:
  CPU: 6 PID: 238 Comm: kworker/6:1H Not tainted 5.3.0-rc1-next-20190724-yocto-standard+ #62
  Hardware name: Marvell OcteonTX CN96XX board (DT)
  Workqueue: kblockd blk_mq_run_work_fn
  pstate: 80c00009 (Nzcv daif +PAN +UAO)
  pc : debug_dma_map_sg+0x2b8/0x350
  lr : debug_dma_map_sg+0x2b8/0x350
  sp : ffff00001770f9e0
  x29: ffff00001770f9e0 x28: ffffffff00000000
  x27: 00000000ffffffff x26: ffff800bc2c73180
  x25: ffff000010e83700 x24: 0000000000000002
  x23: 0000000000000001 x22: 0000000000000001
  x21: 0000000000000000 x20: ffff800bc48ba0b0
  x19: ffff800bc97e8c00 x18: ffffffffffffffff
  x17: 0000000000000000 x16: 0000000000000000
  x15: ffff000010e835c8 x14: 6874207265676e6f
  x13: 6c20746e656d6765 x12: 7320677320676e69
  x11: 7070616d203a342e x10: 31303a31303a3030
  x9 : 303020636d6d5f78 x8 : 35363d78616d5b20
  x7 : 00000000000002fd x6 : ffff000010fd57dc
  x5 : 0000000000000000 x4 : ffff0000106c61f0
  x3 : 00000000ffffffff x2 : 0000800bee060000
  x1 : 7010678df3041a00 x0 : 0000000000000000
  Call trace:
   debug_dma_map_sg+0x2b8/0x350
   cvm_mmc_request+0x3c4/0x988
   __mmc_start_request+0x9c/0x1f8
   mmc_start_request+0x7c/0xb0
   mmc_blk_mq_issue_rq+0x5c4/0x7b8
   mmc_mq_queue_rq+0x11c/0x278
   blk_mq_dispatch_rq_list+0xb0/0x568
   blk_mq_do_dispatch_sched+0x6c/0x108
   blk_mq_sched_dispatch_requests+0x110/0x1b8
   __blk_mq_run_hw_queue+0xb0/0x118
   blk_mq_run_work_fn+0x28/0x38
   process_one_work+0x210/0x490
   worker_thread+0x48/0x458
   kthread+0x130/0x138
   ret_from_fork+0x10/0x1c

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Fixes: ba3869ff32 ("mmc: cavium: Add core MMC driver for Cavium SOCs")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-06 18:59:14 +02:00
Baolin Wang
c6303c5d52 mmc: sdhci-sprd: Fix the incorrect soft reset operation when runtime resuming
The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.

In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".

However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-08-06 18:59:14 +02:00
Joe Perches
665e985c2f mmc: meson-mx-sdio: Fix misuse of GENMASK macro
Arguments are supposed to be ordered high then low.

Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic
Meson8 and Meson8b SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-22 15:09:23 +02:00
Douglas Anderson
ba2d139b02 mmc: dw_mmc: Fix occasional hang after tuning on eMMC
In commit 46d179525a ("mmc: dw_mmc: Wait for data transfer after
response errors.") we fixed a tuning-induced hang that I saw when
stress testing tuning on certain SD cards.  I won't re-hash that whole
commit, but the summary is that as a normal part of tuning you need to
deal with transfer errors and there were cases where these transfer
errors was putting my system into a bad state causing all future
transfers to fail.  That commit fixed handling of the transfer errors
for me.

In downstream Chrome OS my fix landed and had the same behavior for
all SD/MMC commands.  However, it looks like when the commit landed
upstream we limited it to only SD tuning commands.  Presumably this
was to try to get around problems that Alim Akhtar reported on exynos
[1].

Unfortunately while stress testing reboots (and suspend/resume) on
some rk3288-based Chromebooks I found the same problem on the eMMC on
some of my Chromebooks (the ones with Hynix eMMC).  Since the eMMC
tuning command is different (MMC_SEND_TUNING_BLOCK_HS200
vs. MMC_SEND_TUNING_BLOCK) we were basically getting back into the
same situation.

I'm hoping that whatever problems exynos was having in the past are
somehow magically fixed now and we can make the behavior the same for
all commands.

[1] https://lkml.kernel.org/r/CAGOxZ53WfNbaMe0_AM0qBqU47kAfgmPBVZC8K8Y-_J3mDMqW4A@mail.gmail.com

Fixes: 46d179525a ("mmc: dw_mmc: Wait for data transfer after response errors.")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-22 14:30:23 +02:00
Baolin Wang
fc62113b32 mmc: host: sdhci-sprd: Fix the missing pm_runtime_put_noidle()
When the SD host controller tries to probe again due to the derferred
probe mechanism, it will always keep the SD host device as runtime
resume state due to missing the runtime put operation in error path
last time.

Thus add the pm_runtime_put_noidle() in error path to make the PM runtime
counter balance, which can make the SD host device's PM runtime work well.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-22 14:22:44 +02:00
Linus Torvalds
8931084c0d MMC core:
- Let the dma map ops deal with bouncing and drop dma_max_pfn() from the
    dma-mapping interface for ARM
  - Convert the generic MMC DT doc to YAML schemas
  - Drop questionable support for powered-on re-init of SDIO cards at
    runtime resume and for SDIO HW reset
  - Prevent questionable re-init of powered-on removable SDIO cards at
    system resume
  - Cleanup and clarify some SDIO core code
 
 MMC host:
  - tmio: Make runtime PM enablement more flexible for variants
  - tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt to clarify
  - sdhci-pci: Add support for Intel EHL
  - sdhci-pci-o2micro: Enable support for 8-bit bus
  - sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
  - sdhci-of-esdhc: Improve clock management and tuning
  - sdhci_am654: Enable support for 4 and 8-bit bus on J721E
  - sdhci-sprd: Use pinctrl for a proper signal voltage switch
  - sdhci-sprd: Add support for HS400 enhanced strobe mode
  - sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the clock
  - sdhci-sprd: Add support for optional gate clock
  - sunxi-mmc: Convert DT doc to YAML schemas
  - meson-gx: Add support for broken DRAM access for DMA
 
 MEMSTICK core:
  - Fixup error path of memstick_init()
 -----BEGIN PGP SIGNATURE-----
 
 iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAl0l7iYXHHVsZi5oYW5z
 c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCnZnRAA0nBPUsFMl559lySNwO+WjBVo
 z58dw+J3jDTZ5gFGAUOrnYkZfGEweRwzWnfED6Dyh+e+SJiRnSZH8XRTJEAUeTgi
 9KWVr+VGpjZyctNJaMKTeJbPiu/50UVRLJeOGcdJWdMMC9ZlJjKKC2xgyVsInq7P
 wKE8T3k5afNxABgrKtOTKKONCPRNMVyHdMXzUNFLhlj/du9rR5K7f429RhpPU6GU
 7jQ7z9147mwRYm5frn1nx3IvrJUaGyiiSs1ln1PnOV9LsUfVP5NluvbYA6nS4e3V
 jU64Rvf+9RIHTt2z+ZWTjqrNb/2Ug4faPHc7D4Yl4PEsesR51+tWbpLWUX7Mmm6d
 2gbWFv3kzYvSU2G4ztMTrLcsQmd64W1GocXFPvh/UdfQf1200abenj17Gdl0h3Ze
 +NouYXwMw+n1wHNciotpaR8OMHGV6zo0dvDczpc3r73wzxoeNGdiuVlppFcIGvdA
 950oPiqNrFtz2S1DZ9HLeISMajRts7B1nvsr9a/XXa8Us1M6whQDJbMDTynR4Fky
 j8Sw+9nCk0gupuNcfOrHN9TfOf6Tc5BtIvGqhVF6wmDRtRubfc9HReRheioU67EO
 PsWe+xpS/8pg/lJNzBm6i0isCmce+rNbZTtpil33yS4Tv85KhGw1XOZ6HLoPrOmN
 HYPJtDUvOMKlH6M1rJM=
 =vkWp
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Let the dma map ops deal with bouncing and drop dma_max_pfn() from
     the dma-mapping interface for ARM
   - Convert the generic MMC DT doc to YAML schemas
   - Drop questionable support for powered-on re-init of SDIO cards at
     runtime resume and for SDIO HW reset
   - Prevent questionable re-init of powered-on removable SDIO cards at
     system resume
   - Cleanup and clarify some SDIO core code

  MMC host:
   - tmio: Make runtime PM enablement more flexible for variants
   - tmio/renesas_sdhi: Rename DT doc tmio_mmc.txt to renesas,sdhi.txt
     to clarify
   - sdhci-pci: Add support for Intel EHL
   - sdhci-pci-o2micro: Enable support for 8-bit bus
   - sdhci-msm: Prevent acquiring a mutex while holding a spin_lock
   - sdhci-of-esdhc: Improve clock management and tuning
   - sdhci_am654: Enable support for 4 and 8-bit bus on J721E
   - sdhci-sprd: Use pinctrl for a proper signal voltage switch
   - sdhci-sprd: Add support for HS400 enhanced strobe mode
   - sdhci-sprd: Enable PHY DLL and allow delay config to stabilize the
     clock
   - sdhci-sprd: Add support for optional gate clock
   - sunxi-mmc: Convert DT doc to YAML schemas
   - meson-gx: Add support for broken DRAM access for DMA

  MEMSTICK core:
   - Fixup error path of memstick_init()"

* tag 'mmc-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
  mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
  mmc: alcor: remove a redundant greater or equal to zero comparison
  mmc: sdhci-msm: fix mutex while in spinlock
  mmc: sdhci_am654: Make some symbols static
  dma-mapping: remove dma_max_pfn
  mmc: core: let the dma map ops handle bouncing
  dt-binding: mmc: rename tmio_mmc.txt to renesas,sdhi.txt
  mmc: sdhci-sprd: Add pin control support for voltage switch
  dt-bindings: mmc: sprd: Add pinctrl support
  mmc: sdhci-sprd: Add start_signal_voltage_switch ops
  mmc: sdhci-pci: Add support for Intel EHL
  mmc: tmio: Use dma_max_mapping_size() instead of a workaround
  mmc: sdio: Drop unused in-parameter from mmc_sdio_init_card()
  mmc: sdio: Drop unused in-parameter to mmc_sdio_reinit_card()
  mmc: sdio: Don't re-initialize powered-on removable SDIO cards at resume
  mmc: sdio: Drop powered-on re-init at runtime resume and HW reset
  mmc: sdio: Move comment about re-initialization to mmc_sdio_reinit_card()
  mmc: sdio: Drop mmc_claim|release_host() in mmc_sdio_power_restore()
  mmc: sdio: Turn sdio_run_irqs() into static
  mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
  ...
2019-07-11 18:11:21 -07:00
YueHaibing
59592cc1f5 mmc: sdhci_am654: Add dependency on MMC_SDHCI_AM654
Fix build error:

drivers/mmc/host/sdhci_am654.o: In function `sdhci_am654_probe':
drivers/mmc/host/sdhci_am654.c:464: undefined reference to `__devm_regmap_init_mmio_clk'
drivers/mmc/host/sdhci_am654.o:(.debug_addr+0x3f8): undefined reference to `__devm_regmap_init_mmio_clk'

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: aff88ff23512 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
Colin Ian King
42248a918d mmc: alcor: remove a redundant greater or equal to zero comparison
A greater or equal comparison on the unsigned int variable tmp_diff
is always true as unsigned ints are never negative.  Hence the
comparison is redundant and can be removed.

Addresses-Coverity: ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
Jorge Ramirez-Ortiz
5e6b6651d2 mmc: sdhci-msm: fix mutex while in spinlock
mutexes can sleep and therefore should not be taken while holding a
spinlock. move clk_get_rate (can sleep) outside the spinlock protected
region.

Fixes: 83736352e0 ("mmc: sdhci-msm: Update DLL reset sequence")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
YueHaibing
8751c8bd8b mmc: sdhci_am654: Make some symbols static
Fix sparse warnings:

drivers/mmc/host/sdhci_am654.c:192:6: warning: symbol 'sdhci_j721e_4bit_set_clock' was not declared. Should it be static?
drivers/mmc/host/sdhci_am654.c:261:18: warning: symbol 'sdhci_j721e_8bit_ops' was not declared. Should it be static?
drivers/mmc/host/sdhci_am654.c:284:18: warning: symbol 'sdhci_j721e_4bit_ops' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
Baolin Wang
29ca763fc2 mmc: sdhci-sprd: Add pin control support for voltage switch
For Spreadtrum SD card voltage switching, besides regulator setting,
it also need switch related pin's state to output corresponding voltage.

This patch adds pin control operation to support voltage switch.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
Baolin Wang
eef9e0a60e mmc: sdhci-sprd: Add start_signal_voltage_switch ops
For Spreadtrum SD host controller, we can not use standard SD registers
to change and detect the I/O voltage signals, since our voltage regulator
for I/O is fixed in hardware, and no signals were connected to the SD
controller. Thus add Spreadtrum specific voltage switch ops to change
voltage instead of using standard SD host registers.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
Adrian Hunter
cb3a7d4a0a mmc: sdhci-pci: Add support for Intel EHL
Add PCI Ids for Intel EHL.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
Yoshihiro Shimoda
63624d13b2 mmc: tmio: Use dma_max_mapping_size() instead of a workaround
Since the commit 133d624b1c ("dma: Introduce dma_max_mapping_size()")
provides a helper function to get the max mapping size, we can use
the function instead of the workaround code for swiotlb.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-07-10 13:17:30 +02:00
Linus Torvalds
c884d8ac7f SPDX update for 5.2-rc6
Another round of SPDX updates for 5.2-rc6
 
 Here is what I am guessing is going to be the last "big" SPDX update for
 5.2.  It contains all of the remaining GPLv2 and GPLv2+ updates that
 were "easy" to determine by pattern matching.  The ones after this are
 going to be a bit more difficult and the people on the spdx list will be
 discussing them on a case-by-case basis now.
 
 Another 5000+ files are fixed up, so our overall totals are:
 	Files checked:            64545
 	Files with SPDX:          45529
 
 Compared to the 5.1 kernel which was:
 	Files checked:            63848
 	Files with SPDX:          22576
 This is a huge improvement.
 
 Also, we deleted another 20000 lines of boilerplate license crud, always
 nice to see in a diffstat.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
 kbsjBGEJpLbMRB2krnaU
 =RMcT
 -----END PGP SIGNATURE-----

Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx

Pull still more SPDX updates from Greg KH:
 "Another round of SPDX updates for 5.2-rc6

  Here is what I am guessing is going to be the last "big" SPDX update
  for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
  that were "easy" to determine by pattern matching. The ones after this
  are going to be a bit more difficult and the people on the spdx list
  will be discussing them on a case-by-case basis now.

  Another 5000+ files are fixed up, so our overall totals are:
	Files checked:            64545
	Files with SPDX:          45529

  Compared to the 5.1 kernel which was:
	Files checked:            63848
	Files with SPDX:          22576

  This is a huge improvement.

  Also, we deleted another 20000 lines of boilerplate license crud,
  always nice to see in a diffstat"

* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
  ...
2019-06-21 09:58:42 -07:00
Thomas Gleixner
d2912cb15b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:55 +02:00
Thomas Gleixner
38cf0d46f4 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 463
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of version 2 of the gnu general public license as
  published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses the full gnu general public license is included in this
  distribution in the file called copying

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.258730266@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:10 +02:00
Thomas Gleixner
caab277b1d treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 234
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 503 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:07 +02:00
Raul E Rangel
6e8e1acda6 mmc: sdhci: Fix indenting on SDHCI_CTRL_8BITBUS
Remove whitespace in front of SDHCI_CTRL_8BITBUS. The value is not part
of SDHCI_CTRL_DMA_MASK.

Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-18 13:39:03 +02:00
Raul E Rangel
de23f0b757 mmc: sdhci: sdhci-pci-o2micro: Check if controller supports 8-bit width
The O2 controller supports 8-bit EMMC access.

JESD84-B51 section A.6.3.a defines the bus testing procedure that
`mmc_select_bus_width()` implements. This is used to determine the actual
bus width of the eMMC.

Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-18 13:39:03 +02:00
Ulf Hansson
99a934443d Merge branch 'fixes' into next 2019-06-18 13:38:49 +02:00
Raul E Rangel
0f7b79a44e mmc: sdhci: sdhci-pci-o2micro: Correctly set bus width when tuning
The O2Micro controller only supports tuning at 4-bits. So the host driver
needs to change the bus width while tuning and then set it back when done.

There was a bug in the original implementation in that mmc->ios.bus_width
also wasn't updated. Thus setting the incorrect blocksize in
sdhci_send_tuning which results in a tuning failure.

Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Fixes: 0086fc217d ("mmc: sdhci: Add support for O2 hardware tuning")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-18 13:38:06 +02:00
Yangbo Lu
791463ba1a mmc: sdhci-of-esdhc: use 1/2 periperhal clock for ls1028a
LS1028A used 1/2 periperhal clock as one reference clock.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 13:33:54 +02:00
Yangbo Lu
04509d7709 mmc: sdhci-of-esdhc: set the sd clock divisor value above 3
This patch is to set the sd clock divisor value above 3 in tuning mode

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 13:33:44 +02:00
Greg Kroah-Hartman
5928d8929d mmc: host: s3cmci: no need to check return value of debugfs_create functions
When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Also, because there is no need to save the file dentries, remove them
from the host-specific structure and just recursively delete the
directory that the driver created, when shutting down.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 13:31:29 +02:00
Greg Kroah-Hartman
fcac152782 mmc: host: dw_mmc: no need to check return value of debugfs_create functions
When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 13:31:21 +02:00
Greg Kroah-Hartman
091eb12f62 mmc: host: atmel-mci: no need to check return value of debugfs_create functions
When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 13:30:54 +02:00
Ulf Hansson
163367c952 Merge branch 'fixes' into next 2019-06-17 13:28:12 +02:00
jjian zhou
20314ce30a mmc: mediatek: fix SDIO IRQ detection issue
If cmd19 timeout or response crcerr occurs during execute_tuning(),
it need invoke msdc_reset_hw(). Otherwise SDIO IRQ can't be detected.

Signed-off-by: jjian zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Fixes: 5215b2e952 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 13:26:50 +02:00
jjian zhou
8a5df8ac62 mmc: mediatek: fix SDIO IRQ interrupt handle flow
SDIO IRQ is triggered by low level. It need disable SDIO IRQ
detected function. Otherwise the interrupt register can't be cleared.
It will process the interrupt more.

Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Fixes: 5215b2e952 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 13:25:44 +02:00
Faiz Abbas
1accbced1c mmc: sdhci_am654: Add Support for 4 bit IP on J721E
Add support for 4 bit instances on TI's J721E devices. Because these
instances have no DLL, introduce a DLL_PRESENT flag and make sure DLL
related registers are only accessed when it is present. Also add a
separate set_clock callback for this compatible.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 12:02:58 +02:00
Faiz Abbas
99909b55f2 mmc: sdhci_am654: Add Support for 8 bit IP on J721E
The 8 bit IP on the TI's J721E device departs from the AM654x IP in some
ways which require special handling. Create a driver_data structure
which holds the pltfm_data and a flags field which is used to indicate
these differences. These are the following:

1. The pins are not muxed with anything else inside the SoC and hence the
   IOMUX_ENABLE field does not exist. Add a flag which is used to
   indicate the presence of the field.

2. The register field used to select DLL frequency is 3 bit wide as
   compared to 2 bits in AM65x. Add another flag which differentiates
   between 3 bit and 2 bit fields.

3. The strobe select field is 8 bit wide as compared to 4 bits for
   AM65x. Add yet another flag to indicate this difference. Strobe select
   is used only for HS400 speed mode, support for which has not yet been
   added in AM65x.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-17 12:02:58 +02:00
Wolfram Sang
ef4a8d90b7 mmc: sdhi: remove unneeded initialization
Bools are initialized to 'false' by default.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:13:25 +02:00
Wolfram Sang
6a6869869a mmc: sdhi: improve quirk descriptions
Quirks show up in new SoCs as well, so the naming should be generic.
Describe them by what they do.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:12:34 +02:00
Ulf Hansson
07649d9550 Merge branch 'fixes' into next 2019-06-10 17:12:20 +02:00
Thierry Reding
00a9584ead sdhci: tegra: Do not log error message on deferred probe
Recent changes have made it much more likely that clocks are not available,
when the SDHCI driver is first probed. However, that is a situation that
the driver can cope with just fine.

To avoid confusion, don't output an error when this happens.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:11:09 +02:00
Baolin Wang
5f2f4e0da2 mmc: sdhci-sprd: Add PHY DLL delay configuration
Set the PHY DLL delay for each timing mode, which is used to sample the clock
accurately and make the clock more stable.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:11:09 +02:00
Baolin Wang
87a395c27b mmc: sdhci-sprd: Enable PHY DLL to make clock stable
For the Spreadtrum SD host controller, when we changed the clock to be
more than 52M, we should enable the PHY DLL which is used to track the
clock frequency to make the clock work more stable. Otherwise deviation
may occur of the higher clock.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:11:09 +02:00
Baolin Wang
494c11e1a5 mmc: sdhci-sprd: Add HS400 enhanced strobe mode
Add HS400 enhanced strobe mode support for Spreadtrum SD host controller.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:11:09 +02:00
Baolin Wang
7486831d7d mmc: sdhci-sprd: Implement the get_max_timeout_count() interface
Implement the get_max_timeout_count() interface to set the Spredtrum SD
host controller actual maximum timeout count.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:11:09 +02:00
Baolin Wang
ebd88a38db mmc: sdhci-sprd: Add optional gate clock support
For the Spreadtrum SC9860 platform, we should enable another gate clock
'2x_enable' to make the SD host controller work well.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-06-10 17:11:09 +02:00