For the memory size ( > 512MB, < 1GB), the MSA setting is:
- SSEG0: PHY_START , PHY_START + 512MB
- SSEG1: PHY_START + 512MB, PHY_START + 1GB
But the real memory is no more than 1GB, there is a gap between the
end size of memory and border of 1GB. CPU could speculatively
execute to that gap and if the gap of the bus couldn't respond to
the CPU request, then the crash will happen.
Now make the setting with:
- SSEG0: PHY_START , PHY_START + 512MB (no change)
- SSEG1: Disabled (We use highmem to use the memory of 512MB~1GB)
We also deprecated zhole_szie[] settings, it's only used by arm
style CPUs. All memory gap should use Reserved setting of dts in
csky system.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Some CPUs don't support icache.va instruction to maintain the whole
smp cores' icache. Using icache.all + IPI casue a lot on performace
and using defer mechanism could reduce the number of calling icache
_flush_all functions.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
The abiv2 CPUs are all PIPT cache, so there is no need to implement
flush_icache_page function.
The function flush_icache_user_range hasn't been used, so just
remove it.
The function flush_cache_range is not necessary for PIPT cache when
tlb mapping changed.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
In the past, we didn't care about kernel sp when saving pt_reg. But in some
cases, we still need pt_reg->usp to represent the kernel stack before enter
exception.
For cmpxhg in atomic.S, we need save and restore usp for above.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
610 has vipt aliasing issue, so we need to finish the cache flush
apis mentioned in cachetlb.rst to avoid data corruption.
Here is the list of modified apis in the patch:
- flush_kernel_dcache_page (new add)
- flush_dcache_mmap_lock (new add)
- flush_dcache_mmap_unlock (new add)
- flush_kernel_vmap_range (new add)
- invalidate_kernel_vmap_range (new add)
- flush_anon_page (new add)
- flush_cache_range (new add)
- flush_cache_vmap (flush all)
- flush_cache_vunmap (flush all)
- flush_cache_mm (only dcache flush)
- flush_icache_page (just nop)
- copy_from_user_page (remove no need flush)
- copy_to_user_page (remove no need flush)
Change to V2:
- Fixup compile error with xa_lock*(&mapping->i_pages)
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@infradead.org>
We prohibit non-aligned access in kernel mode, but some special NIC
driver needs to support kernel-state unaligned access. For example,
when the bus does not support unaligned access, IP header parsing
will cause non-aligned access and driver does not recopy the skb
buffer to dma for performance reasons.
Added kernel_enable & user_enable to control unaligned access and
added kernel_count & user_count for statistical unaligned access.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
We use defer cache flush mechanism to improve the performance of
610, but the implementation is wrong. We fix it up now and update
the mechanism:
- Zero page needn't be flushed.
- If page is file mapping & non-touched in user space, defer flush.
- If page is anon mapping or dirty file mapping, flush immediately.
- In update_mmu_cache finish the defer flush by flush_dcache_page().
For 610 we need take care the dcache aliasing issue:
- VIPT cache with 8K-bytes size per way in 4K page granularity.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Current arch_get_unmapped_area() of abiv1 doesn't use standard kernel
api. After referring to the implementation of arch/arm, we implement
it with vm_unmapped_area() from linux/mm.h.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
This round of csky subsystem gives two features (ASID algorithm update,
Perf pmu record support) and some fixups.
Feature:
- csky: Revert mmu ASID mechanism
- csky: Add new asid lib code from arm
- csky: Use generic asid algorithm to implement switch_mm
- csky: Improve tlb operation with help of asid
- csky: Init pmu as a device
- csky: Add count-width property for csky pmu
- csky: Add pmu interrupt support
- csky: Fix perf record in kernel/user space
- dt-bindings: csky: Add csky PMU bindings
Fixup:
- csky: Fixup no panic in kernel for some traps
- csky: Fixup some error count in 810 & 860.
- csky: Fixup abiv1 memset error
CI-Tested: https://gitlab.com/c-sky/buildroot/pipelines/68656845
-----BEGIN PGP SIGNATURE-----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=PbF1
-----END PGP SIGNATURE-----
Merge tag 'csky-for-linus-5.3-rc1' of git://github.com/c-sky/csky-linux
Pull arch/csky pupdates from Guo Ren:
"This round of csky subsystem gives two features (ASID algorithm
update, Perf pmu record support) and some fixups.
ASID updates:
- Revert mmu ASID mechanism
- Add new asid lib code from arm
- Use generic asid algorithm to implement switch_mm
- Improve tlb operation with help of asid
Perf pmu record support:
- Init pmu as a device
- Add count-width property for csky pmu
- Add pmu interrupt support
- Fix perf record in kernel/user space
- dt-bindings: Add csky PMU bindings
Fixes:
- Fixup no panic in kernel for some traps
- Fixup some error count in 810 & 860.
- Fixup abiv1 memset error"
* tag 'csky-for-linus-5.3-rc1' of git://github.com/c-sky/csky-linux:
csky: Fixup abiv1 memset error
csky: Improve tlb operation with help of asid
csky: Use generic asid algorithm to implement switch_mm
csky: Add new asid lib code from arm
csky: Revert mmu ASID mechanism
dt-bindings: csky: Add csky PMU bindings
dt-bindings: interrupt-controller: Update csky mpintc
csky: Fixup some error count in 810 & 860.
csky: Fix perf record in kernel/user space
csky: Add pmu interrupt support
csky: Add count-width property for csky pmu
csky: Init pmu as a device
csky: Fixup no panic in kernel for some traps
csky: Select intc & timer drivers
Current memset implementation in abiv1 is wrong and it'll cause unalign
access. Just remove it and use the generic one. This patch will cause
performance degradation and we will improve it with a new design in next
patchset.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Use linux generic asid/vmid algorithm to implement csky
switch_mm function. The algorithm is from arm and it could
work with SMP system. It'll help reduce tlb flush for
switch_mm in task/vm switch.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
As synchronous exceptions really only make sense against the current
task (otherwise how are you synchronous) remove the task parameter
from from force_sig_fault to make it explicit that is what is going
on.
The two known exceptions that deliver a synchronous exception to a
stopped ptraced task have already been changed to
force_sig_fault_to_task.
The callers have been changed with the following emacs regular expression
(with obvious variations on the architectures that take more arguments)
to avoid typos:
force_sig_fault[(]\([^,]+\)[,]\([^,]+\)[,]\([^,]+\)[,]\W+current[)]
->
force_sig_fault(\1,\2,\3)
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of phys_offset is so common for global export and it may
conflict with some local name. So change phys_offset to va_pa_offset
which also used by riscv.
Also use __pa() and __va() instead of using phys_offset directly.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Modify SETUP_MMU macro to fit on both MMU-on or MMU-off enviornment
and vmlinux could bootup from MMU off enviornment for some cases.
Unify the style of _start and _start_smp_secondary in head.S to make
head.S looks more concise and easy to understand.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
In trace events as tracepoints context are not able to
be retrieve with task_pt_regs. Without arch caller regs
support the pt_regs context will be all zero, perf can
not parsing the callchain and resolving the symbols
correctly, some time will even get into deadlock
while handling the page fault, eg:
perf kmem —page record ls
Changelog
- Add test case cmd in comment
- Use regs_fp(regs) which is defined in abi/regdef.h
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Before this patch csky-linux need CONFIG_RAM_BASE to determine start
physical address. Now we use phys_offset variable to replace the macro
of PHYS_OFFSET and we setup phys_offset with real physical address which
is determined during startup in head.S.
With this patch we needn't re-compile kernel for different start
physical address. ie: 0x0 / 0xc0000000 start physical address could use
the same vmlinux, be care different start address must be 512MB aligned.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Linux kernel has provided some apis for arch signal's implementation.
For example:
restore_saved_sigmask()
set_current_blocked()
restore_altstack()
But in last version of csky signal.c didn't use them and some codes are
confusing, so reconstruct signal.c with reference to riscv's code.
Now csky signal.c implementation are very close to riscv and we can
get the following benefits:
- Clear code structure
- The signal code of riscv and csky can be reviewed together
- Promoting the unification of arch's signal implementation
Also modified the related code in entry.S
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
We could use regs->sr 16-24 bits to detect syscall: VEC_TRAP0 and
r11_sig is no necessary for current implementation.
In this patch, we implement the in_syscall and forget_syscall which are
inspired from arm & nds32, but csky pt_regs has no syscall_num element
and we just set zero to regs->sr's vector-bits-field instead.
For ret_from_fork, current task was forked from parent which is in syscall
progress and its regs->sr has been already setted with VEC_TRAP0. See:
arch/csky/kernel/process.c: copy_thread()
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Previous syscall_trace implementation couldn't support AUDITSYSCALL and
SYSCALL_TRACEPOINTS. Now we redesign it to support audit_syscall
and syscall_tracepoints just like other archs'.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Dmitry V. Levin <ldv@altlinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HI, LO, DSPCR registers are 807/810 related regs and no need for 610/860.
All of the regs must be saved in pt_regs and switch_stack. This patch
fixup saving dspcr reg in switch_stack and pt_regs.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Glibc function mmap(... O_SYNC) will make page to _PAGE_UNCACHE +
_PAGE_SO and strong-order page couldn't support unalignment access.
So remove _PAGE_SO from _PAGE_UNCACHE, also sync abiv1 with the macro
of _PAGE_SO.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Liu Renwei <Renwei.Liu@verisilicon.com>
Tested-by: Yuan Qiyun <qiyun_yuan@c-sky.com>
This patch adds files related to VDSO and our VDSO only support
rt_sigreturn.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This patch adds files related to memory management and here is our
memory-layout:
Fixmap : 0xffc02000 – 0xfffff000 (4 MB - 12KB)
Pkmap : 0xff800000 – 0xffc00000 (4 MB)
Vmalloc : 0xf0200000 – 0xff000000 (238 MB)
Lowmem : 0x80000000 – 0xc0000000 (1GB)
abiv1 CPU (CK610) is VIPT cache and it doesn't support highmem.
abiv2 CPUs are all PIPT cache and they could support highmem.
Lowmem is directly mapped by msa0 & msa1 reg, and we needn't setup
memory page table for it.
Link:https://lore.kernel.org/lkml/20180518215548.GH17671@n2100.armlinux.org.uk/
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
