As pointed by smatch:
drivers/media/dvb-frontends/stv090x.c:2787 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2789 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2791 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2793 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2795 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
The situation of a buffer overflow won't happen, in practice,
with the current values of car_loop table. Yet, the entire logic
that checks for those registration values is too complex. So,
better to add an explicit check, just in case someone changes
the car_loop tables causing a buffer overflow by mistake.
This also helps to remove several smatch warnings, with is good.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
if STV090x_RANGEOK is not returned, then STV090x_OUTOFRANGE
is returned. However, that part of the code is never reached,
as pointed by smatch:
drivers/media/dvb-frontends/stv090x.c:2673 stv090x_get_sig_params() info: ignoring unreachable code.
So, remove the two uneeded elses, with makes the code a little bit
cleaner.
No functional changes, and one less smatch warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While writing changeset fdf1bc9fa2, I noticed some checkpatch
complains about the CodingStyle for function parameters. So,
clean them.
While here, also removes uneeded "extern" from function prototype.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for new type of firmware versions of Si2168 chip.
Old type: n x 8 bytes (all data, first byte seems to be 04 or 05)
New type: n x 17 bytes (1 byte indicates len and max 16 bytes data)
New version of TechnoTrend CT2-4400 drivers
(http://www.tt-downloads.de/bda-treiber_4.3.0.0.zip) contains newer
firmware for Si2168-B40 that is in the new format. It can be extracted
with the following command:
dd if=ttTVStick4400_64.sys ibs=1 skip=323872 count=6919 of=dvb-demod-si2168-b40-01.fw
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A debug printout for firmware version.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Drivers that use dvb_attach can have just one exported symbol,
or they will cause compilation breakages depending on the
selected frontends.
As Jim reported:
drivers/built-in.o: In function `technisat_usb2_set_voltage':
technisat-usb2.c:(.text+0x3b4919): undefined reference to `stv090x_set_gpio'
make: *** [vmlinux] Error 1
That happens because, on his configuration, the configuration
is:
CONFIG_DVB_USB=y
CONFIG_DVB_STV090x=m
Luis proposed ar way to fix, but that would just force the
STV090x to be selected, even if one wants to use a device
with a different frontend.
Instead, let's do the right thing: move set_gpio to the
configuration structure and fill it during dvb_attach().
This way, the driver can still call it, and dvb_attach()
will load stv090x module only if the device really needs it.
Reported by: Jim Davis <jim.epost@gmail.com>
Cc: Luis Rodriguez <mcgrof@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Recent rtl28xxu patch I made moved demod ADC enable from power control
to frontend control (due to slave demod support). Because of that we
need call USB interface frontend control too in order to enable ADC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1416472767
The release_firmware() function was called in some cases by the
si2168_init() function during error handling even if the passed variable
contained still a null pointer. This implementation detail could be improved
by the introduction of another jump label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1416472158
The release_firmware() function was called in some cases by the
m88ds3103_init() function during error handling even if the passed variable
contained still a null pointer. This implementation detail could be improved
by the introduction of another jump label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1416472432
The release_firmware() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement partial PIP mode to carry TS from slave demodulator,
through that master demodulator. RTL2832 demod has TS input
interface to connected another demodulator TS output.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is not ready enough to be released on mainline.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert driver to I2C RegMap API. That offers unified register
access routines, register value caching and more.
We need 3 register maps, one for each register page, as chips has
3 I2C address.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Driver was using DVB proprietary binding model. As it is I2C
device, we could change it to normal kernel I2C driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Separate IF and BW based registers.
Add support for DVB-T and DVB-T2 6MHz channel bandwidth.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is not ready enough to be released on mainline.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement initial support for DVB-T and DVB-T2 modes. Now driver has
basic support for all the modes, DVB-C/T/T2.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It uses I2C bus so better to implement it as a standard I2C driver
model. It was using proprietary DVB binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Original plan was to implement driver as one file per used demod
standard (mn88472_c.c, mn88472_t.c and mn88472_t2.c). However, that
plan was a mistake as driver code differences are so small between
different standards. Due to that rename this file and implement all
the needed functionality to that file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
400ms delay seems to be enough in order to gain DVB-C lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wrong symbol name causes demod attach failure.
Reported-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only DVB-C mode is supported, DVB-T and DVB-T2 are not supported.
Very much feature reduced version, no signal statistics nor normal
chip configuration options.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1> When m88ds3103 works in serial ts mode, its serial ts clock is equal to ts master clock and the clock divider is bypassed.
2> The serial ts clock is configed by the bridge driver just like parallel ts clock.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
move the return to happen before the logic. This way, we can
avoid one extra identation.
This also fixes an identation issue on this function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is hard to read what's there, because it doesn't follow the
CodingStyle.
Add missing whitespaces to split function arguments.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is actually a false positive:
drivers/media/dvb-frontends/cx24110.c:210 cx24110_set_fec() error: buffer overflow 'rate' 7 <= 8
But fixing it is easy: just ensure that the table size will be
limited to FEC_AUTO.
While here, fix spacing on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by spatch:
drivers/media/dvb-frontends/stb0899_drv.c:720 stb0899_send_diseqc_msg() error: buffer overflow 'cmd->msg' 6 <= 7
The buffer size is 6 and not 8. Anyway, the best is to use sizeof(),
to avoid such mistakes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As sparse complains:
drivers/media/dvb-frontends/stv090x.c:3471:30: warning: mixing different enum types
drivers/media/dvb-frontends/stv090x.c:3471:30: int enum fe_delivery_system versus
drivers/media/dvb-frontends/stv090x.c:3471:30: int enum stv090x_delsys
There's actually an error when setting the delivery system on
stv090x_search(): it is using the DVBv5 macros as if they were
the stv090x ones.
Instead, we should convert between the two namespaces, returning
an error if an unsupported delivery system is requested.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That case is not IO error, so better to jump out now, but still
continue polling.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch changed both AF9030 and IT9130 SNR reporting from
dB to relative. Restore AF9030 to old behavior as it has been always
returning 0.1 dB value. Leave IT9130 relative as old IT9130 was
returning relative values.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Snr returns value not correct. Fix it.
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Check return status after each register access routine and avoid
masking return status values.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch changes used signal strength firmware register from
0x800048 to 0x80004a in case of AF9033/AF9035 chip. In practice
reported values were running upside-down, when RR strength increases
reported value decreases and vice versa. That is because of 0x80004a
returns values that are dBm scale, but negative RF strength dBm
returned as positive number.
0x800048 returns 0-100, like percentage
0x80004a returns 0-255 dBm, without a negative sign
So restore old measurement now.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Register 0x800048 is not dB measure but relative scale. Fix it and conform to NorDig specifications.
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It repeated "found a 'Silicon Labs Si2168' in warm state" everytime
when device was opened. Message is aimed to point out firmware is
downloaded, up and running. So print it only in case firmware download
is performed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
M88RS6000 is the integrated chip, which includes tuner and demod. Its
internal demod is similar with M88DS3103 except some registers
definition.
The main different part of this internal demod from others is its
clock/pll generation IP block sitting inside the tuner die. So clock/pll
functions should be configed through its tuner i2c bus, NOT its demod
i2c bus.
The demod of M88RS6000 need the firmware: dvb-demod-m88rs6000.fw
firmware download link:
http://www.dvbsky.net/download/linux/dvbsky-firmware.tar.gz
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
