Since commit 110dd8f19d "[SCSI] libsas: fix scr_read/write users and
update the libata documentation" we have been passing pmp=1 and is_cmd=0
to ata_tf_to_fis(). Praveen reports that eSATA attached drives do not
discover correctly. His investigation found that the BIOS was passing
pmp=0 while Linux was passing pmp=1 and failing to discover the drives.
Update libsas to follow the libata example of pulling the pmp setting
from the ata_link and correct is_cmd to be 1 since all tf's submitted
through ->qc_issue are commands. Presumably libsas lldds do not care
about is_cmd as they have sideband mechanisms to perform link
management.
http://marc.info/?l=linux-scsi&m=138179681726990
[jejb: checkpatch fix]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove the arbitrary expectation in libsas that all SCSI commands are 16 bytes
or less. Instead do all copies via cmd->cmd_len (and use a pointer to this in
the libsas task instead of a copy). Note that this still doesn't enable > 16
byte CDB support in the underlying drivers because their internal format has
to be fixed and the wire format of > 16 byte CDBs according to the SAS spec is
different. the libsas drivers (isci, aic94xx, mvsas and pm8xxx are all
updated for this change.
Cc: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jack Wang <xjtuwjp@gmail.com>
Cc: Lindar Liu <lindar_liu@usish.com>
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
If a result of the SMP discover function is PHY VACANT,
the content of discover response structure (dr) is not valid.
It sometimes happens that dr->attached_sas_addr can contain
even SAS address of other phy. In such case an invalid phy
is created, what causes NULL pointer dereference during
destruction of expander's phys.
So if a result of SMP function is PHY VACANT, the content of discover
response structure (dr) must not be copied to phy structure.
This patch fixes the following bug:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: [<ffffffff811c9002>] sysfs_find_dirent+0x12/0x90
Call Trace:
[<ffffffff811c95f5>] sysfs_get_dirent+0x35/0x80
[<ffffffff811cb55e>] sysfs_unmerge_group+0x1e/0xb0
[<ffffffff813329f4>] dpm_sysfs_remove+0x24/0x90
[<ffffffff8132b0f4>] device_del+0x44/0x1d0
[<ffffffffa016fc59>] sas_rphy_delete+0x9/0x20 [scsi_transport_sas]
[<ffffffffa01a16f6>] sas_destruct_devices+0xe6/0x110 [libsas]
[<ffffffff8107ac7c>] process_one_work+0x16c/0x350
[<ffffffff8107d84a>] worker_thread+0x17a/0x410
[<ffffffff81081b76>] kthread+0x96/0xa0
[<ffffffff81464944>] kernel_thread_helper+0x4/0x10
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In fact the disc_resp buffer will be overwrite by smp response, so we never
found this typo, correct it by using the right one.
Signed-off-by: John Gong <john_gong@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
More prep work for immutable bvecs/effecient bio splitting - usage of
bi_vcnt has to be auditing, so getting rid of all the unnecessary usage
makes that easier.
Plus, bio_segments() is really what this code wanted, as it respects the
current value of bi_idx.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Eric Moore <Eric.Moore@lsi.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: linux-scsi@vger.kernel.org
libsas and ipr pass flags to ata_host_init that are meant for the port.
ata_host flags:
ATA_HOST_SIMPLEX = (1 << 0), /* Host is simplex, one DMA channel per host only */
ATA_HOST_STARTED = (1 << 1), /* Host started */
ATA_HOST_PARALLEL_SCAN = (1 << 2), /* Ports on this host can be scanned in parallel */
ATA_HOST_IGNORE_ATA = (1 << 3), /* Ignore ATA devices on this host. */
flags passed by libsas:
ATA_FLAG_SATA = (1 << 1),
ATA_FLAG_PIO_DMA = (1 << 7), /* PIO cmds via DMA */
ATA_FLAG_NCQ = (1 << 10), /* host supports NCQ */
The only one that aliases is ATA_HOST_STARTED which is a 'don't care' in
the libsas and ipr cases since ata_hosts from these sources are not
registered with libata.
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Brian King <brking@us.ibm.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas power management routines to suspend and recover the sas domain
based on a model where the lldd is allowed and expected to be
"forgetful".
sas_suspend_ha - disable event processing allowing the lldd to take down
links without concern for causing hotplug events.
Regardless of whether the lldd actually posts link down
messages libsas notifies the lldd that all
domain_devices are gone.
sas_prep_resume_ha - on the way back up before the lldd starts link
training clean out any spurious events that were
generated on the way down, and re-enable event
processing
sas_resume_ha - after the lldd has started and decided that all phys
have posted link-up events this routine is called to let
libsas start it's own timeout of any phys that did not
resume. After the timeout an lldd can cancel the
phy teardown by posting a link-up event.
Storage for ex_change_count (u16) and phy_change_count (u8) are changed
to int so they can be set to -1 to indicate 'invalidated'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is in preparation for teaching async_synchronize_full() to sync all
pending async work, and not just on the async_running domain. This
conversion is functionally equivalent, just embedding the existing list
in a new async_domain type.
The .registered attribute is used in a later patch to distinguish
between domains that want to be flushed by async_synchronize_full()
versus those that only expect async_synchronize_{full|cookie}_domain to
be used for flushing.
[jejb: add async.h to scsi_priv.h for struct async_domain]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The timer and the completion are only used for slow path tasks (smp, and
lldd tmfs), yet we incur the allocation space and cpu setup time for
every fast path task.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On the way to add a new sata_device field, noticed that libsas is
carrying port multiplier infrastructure that is explicitly disabled by
sas_discover_sata(). The aic94xx touches the unused port_no, so leave
that field in case there was some use for it.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 198439e4 [SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
commit 19252de6 [SCSI] libsas: fix wide port hotplug issues
The above commits seem to have confused the return value of
sas_ex_discover_dev which is non-zero on failure and
sas_ex_join_wide_port which just indicates short circuiting discovery on
already established ports. The result is random discovery failures
depending on configuration.
Calls to sas_ex_join_wide_port are the source of the trouble as its
return value is errantly assigned to 'res'. Convert it to bool and stop
returning its result up the stack.
Cc: <stable@vger.kernel.org>
Tested-by: Dan Melnic <dan.melnic@amd.com>
Reported-by: Dan Melnic <dan.melnic@amd.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Continue running revalidation until no more broadcast devices are
discovered. Fixes cases where re-discovery completes too early in a
domain with multiple expanders with pending re-discovery events.
Servicing BCNs can get backed up behind error recovery.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The discovery function "sas_rediscover_dev" had two bugs: 1) it did
not pay attention to the return status from the SMP task execution;
2) the stack variable used for the returned SAS address was compared
against 0 without being initialized.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sas_eh_bus_reset_handler() amounts to sas_phy_reset() without
notification of the reset to the lldd. If this is triggered from
eh-cmnd recovery there may be sas_tasks for the lldd to terminate, so
->lldd_I_T_nexus_reset is warranted.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Luben Tuikov <ltuikov@yahoo.com>
Cc: Jack Wang <jack_wang@usish.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
[jacek: modify pm8001_I_T_nexus_reset to return -ENODEV]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When recovering failed eh-cmnds let the lldd attempt an abort via
scsi_abort_eh_cmnd before escalating.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The strategy handlers may be called in places that are problematic for
libsas (i.e. sata resets outside of domain revalidation filtering /
libata link recovery), or problematic for userspace (non-blocking ioctl
to sleeping reset functions). However, these routines are also called
for eh escalations and recovery of scsi_eh_prep_cmnd(), so permit them
as long as we are running in the host's error handler, otherwise arrange
for them to be triggered in eh_context.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
eh is woken up automatically by the presence of failed commands,
scsi_schedule_eh is reserved for cases where there are no failed
commands. This guarantees that host_eh_sceduled is only incremented
when an explicit eh request is made.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
[fixed spurious delete of sas_ata_task_abort]
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When managing shost->host_eh_scheduled libata assumes that there is a
1:1 shost-to-ata_port relationship. libsas creates a 1:N relationship
so it needs to manage host_eh_scheduled cumulatively at the host level.
The sched_eh and end_eh port port ops allow libsas to track when domain
devices enter/leave the "eh-pending" state under ha->lock (previously
named ha->state_lock, but it is no longer just a lock for ha->state
changes).
Since host_eh_scheduled indicates eh without backing commands pinning
the device it can be deallocated at any time. Move the taking of the
domain_device reference under the port_lock to guarantee that the
ata_port stays around for the duration of eh.
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
fill_result_tf() grabs the taskfile flags from the originating qc which
sas_ata_qc_fill_rtf() promptly overwrites. The presence of an
ata_taskfile in the sata_device makes it tempting to just copy the full
contents in sas_ata_qc_fill_rtf(). However, libata really only wants
the fis contents and expects the other portions of the taskfile to not
be touched by ->qc_fill_rtf. To that end store a fis buffer in the
sata_device and use ata_tf_from_fis() like every other ->qc_fill_rtf()
implementation.
Cc: <stable@vger.kernel.org>
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit a692b0eec5.
Tom reports:
[ 8.741033] ------------[ cut here ]------------
[ 8.741038] WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0xc1/0xf0()
[ 8.741040] Hardware name: To Be Filled By O.E.M.
[ 8.741041] sysfs: cannot create duplicate filename
...and missing 2 out of 4 drives connected to mvsas. Commit a692b0ee
made the assumption that all the phy ids an lldd registers to libsas are
unique. However, in the "multi-chip" case mvsas does a rather annoying
duplication of phy ids in the array passed to libsas. So, for example,
chip0 has phy0-3 at ha phy index 0-3 and chip1 has its phy0-3 at ha phy
index 4-7. The more natural model would be to create a scsi_host (and
sas_ha) per chip (controller), but for now revert the naming fix which
unfortunately means dealing with unpredictable end-device names for a
bit longer.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Patrick Thomson <patrick.s.thomson@intel.com>
Reported-by: Tom Rini <trini@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:
sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This changes the ordering of initialization and probing events from:
1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
3/ schedule port probe in DISCE_PROBE
This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:
BUG: unable to handle kernel paging request at 0000000000003b10
IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
...
[<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
[<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
[<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
[<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
[<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]
...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The check_ready implementation in the expander-attached ata device case
polls on sas_ex_phy_discover(). The effect is that the ex_phy fields
(critically ->attached_sas_addr) can change. When ata_eh ends and
libsas comes along to revalidate the domain
sas_unregister_devs_sas_addr() can fail to lookup devices to remove, or
fail to re-add an ata device that ata_eh marked as disabled. So change
the code to skip the sas_address and change count updates when ata_eh is
active.
Cc: Jack Wang <jack_wang@usish.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 899fcf4 "[SCSI] libsas: set attached device type and target
protocols for local phys" setup 'phy' to be dereferenced after
list_for_each_entry(phy, &port->phy_list, port_phy_el) (i.e. phy ==
&port->phy_list) resulting in reports like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000002b0
IP: [<ffffffffa00ce948>] sas_discover_domain+0x29e/0x4fb [libsas]
...fix by deferring sas_phy_set_target() to the end of
sas_get_port_device().
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery. Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry. Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.
Fixes reports like:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
If userspace has decided to disable a phy the kernel should honor that
and not inadvertantly re-enable the phy via error recovery. This is
more straightforward in the sata case where link recovery (via
libata-eh) is separate from sas_task cancelling in libsas-eh. Teach
libsas to accept -ENODEV as a successful response from I_T_nexus_reset
('successful' in terms of not escalating further).
This is a more comprehensive fix then "libsas: don't recover 'gone'
devices in sas_ata_hard_reset()", as it is no longer sata-specific.
aic94xx does check the return value from sas_phy_reset() so if the phy
is disabled we proceed with clearing the I_T_nexus.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If discovery returns 0 for target_port_protocols but shows an attached
sata device, just report SAS_PROTOCOL_SATA in the identify data so
userspace can reliably search for sata devices in the domain.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Before:
$ cat /sys/class/sas_phy/phy-6\:3/device_type
none
$ cat /sys/class/sas_phy/phy-6\:3/target_port_protocols
none
After:
$ cat /sys/class/sas_phy/phy-6\:3/device_type
end device
$ cat /sys/class/sas_phy/phy-6\:3/target_port_protocols
sata
Also downgrade the phy_list_lock to _irq instead of _irqsave since
libsas will never call sas_get_port_device with interrupts disbled.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libata issues follow up srsts when the controller has a hard time
recording the signature-fis after a reset, or if the link supports port
multipliers. libsas does not support port multipliers and no current
libsas lldds appear to need help retrieving the signature fis. Revert
it for now to remove confusion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Until all sas_tasks are known to no longer be in-flight this flag gates late
completions from colliding with error handling. However, it must be cleared
prior to the submission of scsi_send_eh_cmnd() requests, otherwise those
commands will never be completed correctly.
This was spotted by slub debug:
=============================================================================
BUG sas_task: Objects remaining on kmem_cache_close()
-----------------------------------------------------------------------------
INFO: Slab 0xffffea001f0eba00 objects=34 used=1 fp=0xffff8807c3aecb00 flags=0x8000000000004080
Pid: 22919, comm: modprobe Not tainted 3.2.0-isci+ #2
Call Trace:
[<ffffffff810fcdcd>] slab_err+0xb0/0xd2
[<ffffffff810e1c50>] ? free_percpu+0x31/0x117
[<ffffffff81100122>] ? kzalloc+0x14/0x16
[<ffffffff81100122>] ? kzalloc+0x14/0x16
[<ffffffff81100486>] kmem_cache_destroy+0x11d/0x270
[<ffffffffa0112bdc>] sas_class_exit+0x10/0x12 [libsas]
[<ffffffff81078fba>] sys_delete_module+0x1c4/0x23c
[<ffffffff814797ba>] ? sysret_check+0x2e/0x69
[<ffffffff8126479e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff81479782>] system_call_fastpath+0x16/0x1b
INFO: Object 0xffff8807c3aed280 @offset=21120
INFO: Allocated in sas_alloc_task+0x22/0x90 [libsas] age=4615311 cpu=2 pid=12966
__slab_alloc.clone.3+0x1d1/0x234
kmem_cache_alloc+0x52/0x10d
sas_alloc_task+0x22/0x90 [libsas]
sas_queuecommand+0x20e/0x230 [libsas]
scsi_send_eh_cmnd+0xd1/0x30c
scsi_eh_try_stu+0x4f/0x6b
scsi_eh_ready_devs+0xba/0x6ef
sas_scsi_recover_host+0xa35/0xab1 [libsas]
scsi_error_handler+0x14b/0x5fa
kthread+0x9d/0xa5
kernel_thread_helper+0x4/0x10
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ata devices are always scanned after ssp. Prior to the ata error
handling reworks libsas would tend to scan devices in ascending expander
phy order. Restore this ordering by deferring ssp discovery to a
DISCE_PROBE event, and keep the probe order consistent with the
discovery order, not the placement of sata devices.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the phy is attached to a new sas address unregister the first address
before processing the new attachment.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas fails to discover all sata devices in the domain. If a device fails
negotiation and does not transmit a signature fis the link needs recovery.
libata already understands how to manage slow to come up links, so treat these
conditions as ata device attach events for the purposes of creating an
ata_port. This allows libata to manage retrying link bring up.
Rediscovery is modified to be careful about checking changes in dev_type. It
looks like libsas leaks old devices if the sas address changes, but that's a
fix for another patch.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make sas-port naming consistent with the expander-attached case whereby
the phy-id is the last digit in the port name. Otherwise we get the
random behavior of the allocation order.
Reported-by: Patrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It's difficult to determine which domain_device is triggering error recovery,
so convert messages like:
sas: ex 5001b4da000e703f phy08:T attached: 5001b4da000e7028
sas: ex 5001b4da000e703f phy09:T attached: 5001b4da000e7029
...
ata7: sas eh calling libata port error handler
ata8: sas eh calling libata port error handler
...into:
sas: ex 5001517e85cfefff phy05:T:9 attached: 5001517e85cfefe5 (stp)
sas: ex 5001517e3b0af0bf phy11:T:8 attached: 5001517e3b0af0ab (stp)
...
sas: ata7: end_device-21:1: dev error handler
sas: ata8: end_device-20:0:5: dev error handler
which shows attached link rate, device type, and associates a
domain_device with its ata_port id to correlate messages emitted from
libata-eh.
As Doug notes, we can also take the opportunity to clarify expander phy
routing capabilities.
[dgilbert@interlog.com: clarify table2table with 'U']
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Holdover from a patch rework, prior to the addition of SAS_DEV_DESTROY
we were holding a reference while the destruct was pending in case the
domain was torn down before the desctruct event ran. That case is
covered by SAS_DEV_DESTROY, and the sas_put_device() just corrupts freed
memory, or worse frees the memory while another agent holds a reference.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Similar to the conversion of the transport-class reset we want bsg
initiated resets to be managed by libata.
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we have a domain with sas and sata devices there may still be sas
recovery actions to take after peeling off the commands to send to
libata.
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the top level expander is hot removed, mark all child devices as gone
before unregistration to short circuit futile recovery.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
