Diagnosing problems related to Window Probes has been hard because
we lack a counter.
TCPWinProbe counts the number of ACK packets a sender has to send
at regular intervals to make sure a reverse ACK packet opening back
a window had not been lost.
TCPKeepAlive counts the number of ACK packets sent to keep TCP
flows alive (SO_KEEPALIVE)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the advent of small rto timers in datacenter TCP,
(ip route ... rto_min x), the following can happen :
1) Qdisc is full, transmit fails.
TCP sets a timer based on icsk_rto to retry the transmit, without
exponential backoff.
With low icsk_rto, and lot of sockets, all cpus are servicing timer
interrupts like crazy.
Intent of the code was to retry with a timer between 200 (TCP_RTO_MIN)
and 500ms (TCP_RESOURCE_PROBE_INTERVAL)
2) Receivers can send zero windows if they don't drain their receive queue.
TCP sends zero window probes, based on icsk_rto current value, with
exponential backoff.
With /proc/sys/net/ipv4/tcp_retries2 being 15 (or even smaller in
some cases), sender can abort in less than one or two minutes !
If receiver stops the sender, it obviously doesn't care of very tight
rto. Probability of dropping the ACK reopening the window is not
worth the risk.
Lets change the base timer to be at least 200ms (TCP_RTO_MIN) for these
events (but not normal RTO based retransmits)
A followup patch adds a new SNMP counter, as it would have helped a lot
diagnosing this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy netlink API treated EPERM (permission denied) as
"operation not supported".
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to get or set the broadcast link window through the
new netlink API. The functionality was unintentionally missing from
the new netlink API. Adding this means that we also fix the breakage
in the old API when coming through the compat layer.
Fixes: 37e2d4843f (tipc: convert legacy nl link prop set to nl compat)
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default link properties can be set for media or bearer. This
functionality was missed when introducing the NL compatibility layer.
This patch implements this functionality in the compat netlink
layer. It works the same way as it did in the old API. We search for
media and bearers matching the "link name". If we find a matching
media or bearer the link tolerance, priority or window is used as
default for new links on that media or bearer.
Fixes: 37e2d4843f (tipc: convert legacy nl link prop set to nl compat)
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA stacks an Ethernet device on top of an Ethernet device. This can
cause false positive lockdep splats for the transmit queue:
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
=============================================
[ INFO: possible recursive locking detected ]
4.0.0-rc7-01838-g70621a215fc7 #386 Not tainted
---------------------------------------------
kworker/0:0/4 is trying to acquire lock:
(_xmit_ETHER#2){+.-...}, at: [<c040e95c>] sch_direct_xmit+0xa8/0x1fc
but task is already holding lock:
(_xmit_ETHER#2){+.-...}, at: [<c03f4208>] __dev_queue_xmit+0x4d4/0x56c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(_xmit_ETHER#2);
lock(_xmit_ETHER#2);
To avoid this, walk the tq queues of the dsa slaves and set a lockdep
class.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change does two things. First it fixes a sparse error for the fact
that the __be16 degrades to an integer. Since that is actually what I am
kind of doing I am simply working around that by forcing both sides of the
comparison to u16.
Also I realized on some compilers I was generating another instruction for
big endian systems such as PowerPC since it was masking the value before
doing the comparison. So to resolve that I have simply pulled the mask out
and wrapped it in an #ifndef __BIG_ENDIAN.
Lastly I pulled this all out into its own function. I notices there are
similar checks in a number of other places so this function can be reused
there to help reduce overhead in these paths as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BR_GROUPFWD_RESTRICTED bitmask restricts users from setting values to
/sys/class/net/brX/bridge/group_fwd_mask that allow forwarding of
some IEEE 802.1D Table 7-10 Reserved addresses:
(MAC Control) 802.3 01-80-C2-00-00-01
(Link Aggregation) 802.3 01-80-C2-00-00-02
802.1AB LLDP 01-80-C2-00-00-0E
Change BR_GROUPFWD_RESTRICTED to allow to forward LLDP frames and document
group_fwd_mask.
e.g.
echo 16384 > /sys/class/net/brX/bridge/group_fwd_mask
allows to forward LLDP frames.
This may be needed for bridge setups used for network troubleshooting or
any other scenario where forwarding of LLDP frames is desired (e.g. bridge
connecting a virtual machine to real switch transmitting LLDP frames that
virtual machine needs to receive).
Tested on a simple bridge setup with two interfaces and host transmitting
LLDP frames on one side of this bridge (used lldpd). Setting group_fwd_mask
as described above lets LLDP frames traverse bridge.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a server application to get the TCP SYN headers for
its passive connections. This is useful if the server is doing
fingerprinting of clients based on SYN packet contents.
Two socket options are added: TCP_SAVE_SYN and TCP_SAVED_SYN.
The first is used on a socket to enable saving the SYN headers
for child connections. This can be set before or after the listen()
call.
The latter is used to retrieve the SYN headers for passive connections,
if the parent listener has enabled TCP_SAVE_SYN.
TCP_SAVED_SYN is read once, it frees the saved SYN headers.
The data returned in TCP_SAVED_SYN are network (IPv4/IPv6) and TCP
headers.
Original patch was written by Tom Herbert, I changed it to not hold
a full skb (and associated dst and conntracking reference).
We have used such patch for about 3 years at Google.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
> net/core/skbuff.c:4108:13: sparse: incorrect type in assignment (different base types)
> net/ipv6/mcast_snoop.c:63 ipv6_mc_check_exthdrs() warn: unsigned 'offset' is never less than zero.
Introduced by 9afd85c9e4
("net: Export IGMP/MLD message validation code")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once tipc_conn_new() returns NULL, the connection should be shut
down immediately, otherwise, oops may happen due to the NULL pointer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently subscriber's lock protects not only subscriber's subscription
list but also all subscriptions linked into the list. However, as all
members of subscription are never changed after they are initialized,
it's unnecessary for subscription to be protected under subscriber's
lock. If the lock is used to only protect subscriber's subscription
list, the adjustment not only makes the locking policy simpler, but
also helps to avoid a deadlock which may happen once creating a
subscription is failed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present subscriber's lock is used to protect the subscription list
of subscriber as well as subscriptions linked into the list. While one
or all subscriptions are deleted through iterating the list, the
subscriber's lock must be held. Meanwhile, as deletion of subscription
may happen in subscription timer's handler, the lock must be grabbed
in the function as well. When subscription's timer is terminated with
del_timer_sync() during above iteration, subscriber's lock has to be
temporarily released, otherwise, deadlock may occur. However, the
temporary release may cause the double free of a subscription as the
subscription is not disconnected from the subscription list.
Now if a reference counter is introduced to subscriber, subscription's
timer can be asynchronously stopped with del_timer(). As a result, the
issue is not only able to be fixed, but also relevant code is pretty
readable and understandable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing a new function makes the purpose of tipc_subscrb_connect_cb
callback routine more clear.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a topology server accepts a connection request from its client,
it allocates a connection instance and a tipc_subscriber structure
object. The former is used to communicate with client, and the latter
is often treated as a subscriber which manages all subscription events
requested from a same client. When a topology server receives a request
of subscribing name services from a client through the connection, it
creates a tipc_subscription structure instance which is seen as a
subscription recording what name services are subscribed. In order to
manage all subscriptions from a same client, topology server links
them into the subscrp_list of the subscriber. So subscriber and
subscription completely represents different meanings respectively,
but function names associated with them make us so confused that we
are unable to easily tell which function is against subscriber and
which is to subscription. So we want to eliminate the confusion by
renaming them.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's use these new, neat helpers.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call make_flow_keys_digest to get a digest from flow keys and
use that to pass skbuff cb and for comparing flows.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users of flow keys (well just sch_choke now) need to pass
flow_keys in skbuff cb, and use them for exact comparisons of flows
so that skb->hash is not sufficient. In order to increase size of
the flow_keys structure, we introduce another structure for
the purpose of passing flow keys in skbuff cb. We limit this structure
to sixteen bytes, and we will technically treat this as a digest of
flow_keys struct hence its name flow_keys_digest. In the first
incaranation we just copy the flow_keys structure up to 16 bytes--
this is the same information previously passed in the cb. In the
future, we'll adapt this for larger flow_keys and could use something
like SHA-1 over the whole flow_keys to improve the quality of the
digest.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_get_hash_perturb instead of doing skb_flow_dissect and then
jhash by hand.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_get_hash_perturb instead of doing skb_flow_dissect and then
jhash by hand.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_get_hash_perturb instead of doing skb_flow_dissect and then
jhash by hand.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_get_hash_perturb instead of doing skb_flow_dissect and then
jhash by hand.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This calls flow_disect and __skb_get_hash to procure a hash for a
packet. Input includes a key to initialize jhash. This function
does not set skb->hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In setups with a global scope address on an interface, and a lesser
scope address on an interface sending IGMP reports, the reports can be
sent using the other interfaces global scope address rather than the
local interface address. RFC 2236 suggests:
Ignore the Report if you cannot identify the source address of
the packet as belonging to a subnet assigned to the interface on
which the packet was received.
since such reports could be forged.
Look at the protocol when deciding if a RT_SCOPE_LINK address should
be used for the packet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC classifiers/actions were converted to RCU by John in the series:
http://thread.gmane.org/gmane.linux.network/329739/focus=329739
and many follow on patches.
This is the last patch from that series that finally drops
ingress spin_lock.
Single cpu ingress+u32 performance goes from 22.9 Mpps to 24.5 Mpps.
In two cpu case when both cores are receiving traffic on the same
device and go into the same ingress+u32 the performance jumps
from 4.5 + 4.5 Mpps to 23.5 + 23.5 Mpps
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoking pkts_acked is currently conditioned on FLAG_ACKED:
receiving a cumulative ACK of new data, or ACK with SYN flag set.
Remove this condition so that CC may get RTT measurements from all SACKs.
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_sacktag_one() always picks the earliest sequence SACKed for RTT.
This might not make sense for congestion control in cases where:
1. ACKs are lost, i.e. a SACK following a lost SACK covers both
new and old segments at the receiver.
2. The receiver disregards the RFC 5681 recommendation to immediately
ACK out-of-order segments.
Give congestion control a RTT for the latest segment SACKed, which is the
most accurate RTT estimate, but preserve the conservative RTT for RTO.
Removes the call to skb_mstamp_get() in tcp_sacktag_one().
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patch passes two values set in tcp_sacktag_one() to
tcp_clean_rtx_queue(). Prepare passing them via struct tcp_sacktag_state.
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid recomputing the Ethernet header location and instead just use the
pointer provided by skb->data. The problem with using eth_hdr is that the
compiler wasn't smart enough to realize that skb->head + skb->mac_header
was the same thing as skb->data before it added ETH_HLEN. By just caching
it off before calling skb_pull_inline we can avoid a few unnecessary
instructions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we process the address in
is_multicast_ether_addr at the same size as the other calls. This allows
us to avoid duplicate reads when used with other calls such as
is_zero_ether_addr or eth_addr_copy. In addition I have added a 64 bit
version of the function so in eth_type_trans we can process the destination
address as a 64 bit value throughout.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change takes advantage of the fact that ETH_P_802_3_MIN is aligned to
512 so as a result we can actually ignore the lower 8b when comparing the
Ethertype to ETH_P_802_3_MIN. This allows us to avoid a byte swap by simply
masking the value and comparing it to the byte swapped value for
ETH_P_802_3_MIN.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch divides the IPv6 flow label space into two ranges:
0-7ffff is reserved for flow label manager, 80000-fffff will be
used for creating auto flow labels (per RFC6438). This only affects how
labels are set on transmit, it does not affect receive. This range split
can be disbaled by systcl.
Background:
IPv6 flow labels have been an unmitigated disappointment thus far
in the lifetime of IPv6. Support in HW devices to use them for ECMP
is lacking, and OSes don't turn them on by default. If we had these
we could get much better hashing in IPv6 networks without resorting
to DPI, possibly eliminating some of the motivations to to define new
encaps in UDP just for getting ECMP.
Unfortunately, the initial specfications of IPv6 did not clarify
how they are to be used. There has always been a vague concept that
these can be used for ECMP, flow hashing, etc. and we do now have a
good standard how to this in RFC6438. The problem is that flow labels
can be either stateful or stateless (as in RFC6438), and we are
presented with the possibility that a stateless label may collide
with a stateful one. Attempts to split the flow label space were
rejected in IETF. When we added support in Linux for RFC6438, we
could not turn on flow labels by default due to this conflict.
This patch splits the flow label space and should give us
a path to enabling auto flow labels by default for all IPv6 packets.
This is an API change so we need to consider compatibility with
existing deployment. The stateful range is chosen to be the lower
values in hopes that most uses would have chosen small numbers.
Once we resolve the stateless/stateful issue, we can proceed to
look at enabling RFC6438 flow labels by default (starting with
scaled testing).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my earlier commit:
653437d02f ("ipv6: Stop /128 route from disappearing after pmtu update"),
there was a horrible typo. Instead of checking RTF_LOCAL on
rt->rt6i_flags, it was checked on rt->dst.flags. This patch fixes
it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hajime Tazaki <tazaki@sfc.wide.ad.jp>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not used.
pedit sets TC_MUNGED when packet content was altered, but all the core
does is unset MUNGED again and then set OK2MUNGE.
And the latter isn't tested anywhere. So lets remove both
TC_MUNGED and TC_OK2MUNGE.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole hlist will be moved, so not need to call hlist_del before
add the hlist_node to other hlist_head.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
_rt6i_peer is no longer needed after the last patch,
'ipv6: Stop rt6_info from using inet_peer's metrics'.
DST_METRICS_FORCE_OVERWRITE is added by
commit e5fd387ad5 ("ipv6: do not overwrite inetpeer metrics prematurely").
Since inetpeer is no longer used for metrics, this bit is also not needed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Michal Kubeček <mkubecek@suse.cz>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_peer is indexed by the dst address alone. However, the fib6 tree
could have multiple routing entries (rt6_info) for the same dst. For
example,
1. A /128 dst via multiple gateways.
2. A RTF_CACHE route cloned from a /128 route.
In the above cases, all of them will share the same metrics and
step on each other.
This patch will steer away from inet_peer's metrics and use
dst_cow_metrics_generic() for everything.
Change Highlights:
1. Remove rt6_cow_metrics() which currently acquires metrics from
inet_peer for DST_HOST route (i.e. /128 route).
2. Add rt6i_pmtu to take care of the pmtu update to avoid creating a
full size metrics just to override the RTAX_MTU.
3. After (2), the RTF_CACHE route can also share the metrics with its
dst.from route, by:
dst_init_metrics(&cache_rt->dst, dst_metrics_ptr(cache_rt->dst.from), true);
4. Stop creating RTF_CACHE route by cloning another RTF_CACHE route. Instead,
directly clone from rt->dst.
[ Currently, cloning from another RTF_CACHE is only possible during
rt6_do_redirect(). Also, the old clone is removed from the tree
immediately after the new clone is added. ]
In case of cloning from an older redirect RTF_CACHE, it should work as
before.
In case of cloning from an older pmtu RTF_CACHE, this patch will forget
the pmtu and re-learn it (if there is any) from the redirected route.
The _rt6i_peer and DST_METRICS_FORCE_OVERWRITE will be removed
in the next cleanup patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is mostly from Steffen Klassert <steffen.klassert@secunet.com>.
I only removed the (rt6->rt6i_dst.plen == 128) check from
ip6_rt_update_pmtu() because the (rt6->rt6i_flags & RTF_CACHE) test
has already implied it.
This patch:
1. Create RTF_CACHE route for /128 non local route
2. After (1), all routes that allow pmtu update should have a RTF_CACHE
clone. Hence, stop updating MTU for any non RTF_CACHE route.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We search only for routes with highest priority metric in
find_rr_leaf(). However if one of these routes is marked
as invalid, we may fail to find a route even if there is
a appropriate route with lower priority. Then we loose
connectivity until the garbage collector deletes the
invalid route. This typically happens if a host route
expires afer a pmtu event. Fix this by searching also
for routes with a lower priority metric.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work for the later bug-fix patch which will stop /128 route
from disappearing after pmtu update.
The later bug-fix patch will allow a /128 route and its RTF_CACHE clone
both exist at the same fib6_node. To do this, we need to prepare the
existing fib6 tree search to expect RTF_CACHE for /128 route.
Note that the fn->leaf is sorted by rt6i_metric. Hence,
RTF_CACHE (if there is any) is always at the front. This property
leads to the following:
1. When doing ip6_route_del(), it should honor the RTF_CACHE flag which
the caller is used to ask for deleting clone or non-clone.
The rtm_to_fib6_config() should also check the RTM_F_CLONED and
then set RTF_CACHE accordingly so that:
- 'ip -6 r del...' will make ip6_route_del() to delete a route
and all its clones. Note that its clones is flushed by fib6_del()
- 'ip -6 r flush table cache' will make ip6_route_del() to
only delete clone(s).
2. Exclude RTF_CACHE from addrconf_get_prefix_route() which
should not configure on a cloned route.
3. No change is need for rt6_device_match() since it currently could
return a RTF_CACHE clone route, so the later bug-fix patch will not
affect it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under stress, ip_idents_reserve() is accessing a contended
cache line twice, with non optimal MESI transactions.
If we place timestamps in separate location, we reduce this
pressure by ~50% and allow atomic_add_return() to issue
a Request for Ownership.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I forgot to update tcp_westwood when changing get_info() behavior,
this patch should fix this.
Fixes: 64f40ff5bb ("tcp: prepare CC get_info() access from getsockopt()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_mark_lost_retrans is not used when FACK is disabled. Since
tcp_update_reordering may disable FACK, it should be called first
before tcp_mark_lost_retrans.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
