After moving tpa6130a2 power management to DAPM, if chip can be physically
powered off (either reset_gpio is defined, or regulator indeed removes
power), then volume change no longer works unless chip is on due to
a running stream.
Fix that by entering regcache cache_only mode while chip is off.
Move regcache calls to tpa6130a2_power() to get them at driver init time
as well.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the FLL parameter calculation, the FVCO should choose the maximum one.
The patch is to fix the bug about the wrong FVCO chosen.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Da7219 does not trigger interrupt to report jack status
when system boots from warm reset because its power
remains on during warm reset.
Doing software reset at probe to handle this.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The volume have a step of 0.375dB, but TLV uses the units 0.01dB. It should
be changed to a step of 0.75dB to match the units of TLV.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Theta/lambda is used to give the fractional portion of the FLL
frequency multiplication. When the synchroniser is active the
reference path lambda value is hard coded in the hardware to
65536. This patch corrects the handling of theta such that it
is scaled to match this denominator, when the synchroniser is
active.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When enabling an FLL use pm_runtime_get_sync() instead of
pm_runtime_get() to ensure that all the register settings
have been written out and the codec is powered-up before
we write the enable bit.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When reclocking an active FLL, to ensure a clean transition, do
not change the gain setting until we have entered free run.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Anything that sets ret in wm2000_anc_transition will have immediately
returned anyway as such we will always return an uninitialised ret at the
bottom of the function. Simply replace the return with a return 0;
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously code defaulted to 32 BCLKS per WCLK which meant 24 and
32 bit DAI formats would not work properly. This patch fixes the
issue by defaulting to 64 BCLKs per WCLK.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch is to fix the static check error as the following.
The patch commit b50455fab4 ("ASoC: nau8825: cross talk suppression
measurement function") from Jun 7, 2016, leads to the following
static checker warning:
sound/soc/codecs/nau8825.c:265 nau8825_sema_acquire()
warn: 'sem:&nau8825->xtalk_sem' is sometimes locked here and
sometimes unlocked.
The semaphone acquire function has return value, and some callers
can do error handling when lock fails.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In chromium, the following steps will make codec function fail.
\1. plug in headphones, Play music
\2. run "powerd_dbus_suspend"
\3. resume from S3
After resume, the jack detection will restart and make configuration
for the headset. Meanwhile, the playback prepares and starts to work.
The two sequences will conflict and make wrong register configuration.
Originally, the driver adds protection for the case when it finds
the playback is active. But the "powerd_dbus_suspend" command will
close the pcm stream before suspend. Therefore, the driver can't
detect the playback after resume, and the protection not works.
For the issue, the driver raises protection every time after resume.
The protection will release after jack detection and configuration
completes, and then the playback just will goes on.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
The TDM mode using PCM format now has two-bit right shift due to the
format configuration in the driver. According to Figure 4-13 in the
CS53L30 datasheet, using ASP_SCLK_INV = 0 and SHIFT_LEFT = 1 should
be the correct combination to create one-bit right shift for the DSP
type A format.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum slot number of CS53L30 is 4 while it should support
the situation that's less than 4 channels based on the rx_mask.
So when the driver validates the last slot location, it should
check the last active slot instead of always the 4th one.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thanks Mark and Anatol for the discussion. According to the result,
the standard C will translate any non-zero value into true, or
false otherwise.
QUOTE:
"6.3.1.2 Boolean type
When any scalar value is converted to _Bool, the result is 0 if the
value compares equal to 0; otherwise, the result is 1
"
Thus, the "!!" idiom is removed.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original design only covers the jack insertion logic is active low.
Add more condition to cover no matter the logic is active low and high.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_* API to simplify the code.
This patch also fixes the return value in probe error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ux500 platform hasn't used board files for a long time, and
nothing defines a ab8500_codec_platform_data, so we can just
remove the probing based on that and always use device tree
properties directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This controls the volume for the line out pins of SGTL5000.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like in Skylake, Kabylake also uses combo jack so add Kabylake to
DMI match for combo jack configuration.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake platform is similar to Skylake. So, add the device id.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some CHT platforms use RT5645 codec which has entry 10EC5640 so add it.
Also add DMI quirk for jack detection.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
[Jack detection]
Suggested-by: Stephen Just <stephenjust@gmail.com>
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add an alsa control for DAC1 digital volume control function
selection. The options are:
0: Gain update immediately
1: Gain update when a zero crossing
2: Gain update when a zero crossing with a soft ramp
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645_PRIV_INDEX(0x6a) indicate the address of PR- registers. So,
it should be volatile.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add supports for 16k (wideband BT) and add a general compatible
string "linux,bt-sco"
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
reg-8a assign the tracking source for each ASRC tracker. The default
value is 0x0000 which means all ASRC trackers will track LRCK1. But
in most cases, we wish each ASRC tracker track the corresponding LRCK.
i.e. ASRC1 tracks LRCK1, ASRC2 tracks LRCK2 and so on. So, we rewrite
reg-8a as 0x0120.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
