While having tda18271 module set with debug=17 (cal & info prints) and
cal=0 (delay calibration process until first use) - I discovered that
during the calibration process, if the frequency test for 69750000
returned a bcal of 0 (see tda18721-fe.c in tda18271_powerscan func) that
the tuner wouldn't be able to pickup any of the frequencies in the range
(all the other frequencies bands returned bcal=1). I spent some time
going over the code and the NXP's tda18271 spec (ver.4 of it i think) and
adding a lot of debug prints and walking/stepping through the calibration
process. I found that when the powerscan fails to find a frequency, the
rf calibration is not run and the default value is supposed to be used in
its place (pulled from the RF_CAL_map table) - but something was getting
goofed up there.
Now, my c coding skills are very rusty, but i think root of the problem is
a signedness issue with the math operation for calculating the rf_a1 and
rf_a2 values in tda18271_rf_tracking_filters_init func, which results in
values like 20648 for rf_a1 (when it should probably have a value like 0,
or so slightly negative that it should be zero - this bad value for rf_a1
would in turn makes the approx calc within
tda18271c2_rf_tracking_filters_correction go out of whack). The simplest
solution i found was to explicitly convert the signedness of the
denominator to avoid the implicit conversion. The values placed into the
u32 rf_freq array should never exceed about 900mhz, so i think the s32 max
value shouldn't be an issue in this case.
I've tested it out a little, and even when i get a bcal=0 with the
modified code, the default calibration value gets used, rf_a1 is zero, and
the tuner seems to lock on the stream and mythtv seems to play it fine.
Signed-off-by: Seth Barry <seth@cyberseth.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multiplication by 62500 causes an overflow in the 32 bit freq variable,
which is later divided by 1000 when using FM radio.
This patch prevents the overflow by scaling the frequency value correctly
upfront. Thanks to Henk Vergonet for spotting the problem and providing
a preliminary patch, which this changeset was based upon.
Cc: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixing kernel oops when driver attemps to load xc2028 firmware.
Note by djh: the patch contribute by Martin is a port of a fix I made during
the PCTV 340e development. It's a temporary workaround that fixes a regression
(an OOPS condition) and the real fix should be in the code that manages the
i2c master on the dib7000p. But this fix does address the immmediate
regression and should be merged upstream until we do a cleaner fix.
Signed-off-by: Martin Samek <martin@marsark.sytes.net>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git commit db48138f6b changed by accident the
assignment of certain USB IDs to their device-specific-handlers.
Thanks to Edward Sheldrake for finding this regression
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (13039): dib0700: not building CONFIG_DVB_TUNER_DIB0070 breaks compilation
V4L/DVB (13038): dvbdev: Remove an anoying/uneeded warning
V4L/DVB (13037): go7007: Revert compatibility code added at the wrong place
media: video: Fix build in saa7164
* remove asm/atomic.h inclusion from linux/utsname.h --
not needed after kref conversion
* remove linux/utsname.h inclusion from files which do not need it
NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by Ingo Molnar:
Here's another new build breakage that triggers in -tip testing:
drivers/built-in.o:(.data+0xb1f40): undefined reference to `dib0070_ctrl_agc_filter'
drivers/built-in.o:(.data+0xb1f80): undefined reference to `dib0070_ctrl_agc_filter'
triggers due to:
CONFIG_DVB_USB_DIB0700=y
CONFIG_DVB_TUNER_DIB0070 is not set
While working on a better approach, for now, let's just select tuner
dib0070 anytime we compile dib0700.
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by Marcin Slusarz <marcin.slusarz@gmail.com>, the warns happens
because CONFIG_DVB_MAX_ADAPTERS depends on CONFIG_DVB_CORE, and there are
valid configs where DVB_CORE is not selected.
This causes such warnings, for every V4L and common drivers that may or
may not be compiled with DVB support:
drivers/media/dvb/dvb-core/dvbdev.h:36:2: warning: #warning invalid CONFIG_DVB_MAX_ADAPTERS value
We can safely remove the warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-tip testing found that the x86 build (64-bit allyesconfig) fails due to:
LD vmlinux.o
drivers/built-in.o:(.bss+0x4b648): multiple definition of `debug'
arch/x86/built-in.o:(.kprobes.text+0x88): first defined here
ld: Warning: size of symbol `debug' changed from 90 in
arch/x86/built-in.o to 4 in drivers/built-in.o
make: *** [vmlinux.o] Error 1
This is because recent saa7164 changes introduced a global symbol
named 'debug'. The x86 platform code already defines a 'debug'
symbol. (which is named in a too generic way as well - but it
can be used nicely to weed out too generic symbols in drivers ;-)
Rename it to saa_debug.
[mchehab@redhat.com: use module_param_named to preserve old name]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
alpha:
drivers/media/dvb/pt1/pt1.c: In function 'pt1_cleanup_tables':
drivers/media/dvb/pt1/pt1.c:422: error: implicit declaration of function 'vfree'
drivers/media/dvb/pt1/pt1.c: In function 'pt1_init_tables':
drivers/media/dvb/pt1/pt1.c:431: error: implicit declaration of function 'vmalloc'
drivers/media/dvb/pt1/pt1.c:431: warning: assignment makes pointer from integer without a cast
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The build of the dabusb driver broke:
drivers/media/video/dabusb.c:758: error: unknown field 'nodename' specified in initializer
drivers/media/video/dabusb.c:758: warning: initialization from incompatible pointer type
make[3]: *** wait: No child processes. Stop.
Due to this commit:
e454cea: Driver-Core: extend devnode callbacks to provide permissions
Missing the dabusb driver's dabusb_nodename() callback.
Similar issues with the iio/industrialio driver in staging, pointed out
and patched by Jean Delvare.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Industrialio-parts-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to several files in drivers/media/video/cx88/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/media/dvb/pt1/pt1.c: In function ‘pt1_probe’:
drivers/media/dvb/pt1/pt1.c:915: warning: ‘DMA_nnBIT_MASK’ is deprecated
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an initial driver for Analog Devices ADV7180 Video Decoder.
So far it only supports query standard.
[akpm@linux-foundation.org: remove unneeded cast]
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the kzalloc and associated test after the stream/query test, to avoid
the need to free the allocated if the stream/query test fails.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to rounding and clipping, exposure and gain settings do not map to
unique register values. Rather than read the registers and report gain
and exposure that may be different than the values that were set, just
cache the latest values that were set and report them. Reduce exposure
range from 0-65535 to 0-255 so libv4l's autogain doesn't take forever.
Remove vestiges of driver signal processing that is now handled by
libv4l.
Signed-off-by: James Blanford <jhblanford@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize image size before it's used to initialize exposure.
Work around lack of exposure set hardware latch with a sequence of
register writes in a single I2C command packet.
Signed-off-by: James Blanford <jhblanford@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
http://linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner
test status analog (PAL-B):
- Sometimes picture is noisy, but it becomes crystal clear after
switching between channels. (happens for example at 687.25 Mhz)
- On a lower frequency (511.25 Mhz) the picture is always sharp, but
lacks colour.
- No sound problems.
- radio untested.
Digital:
- DVB-T/H stream reception works.
- Would expect to see some more channels in the higher frequency region.
Overall is the impression that sensitivity still needs improvement
both in analog and digital modes.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When fast push-pull button of remote control we can received incorrect
key code 0x00. Key information from IR decoder has ID of remote control 2 bytes,
byte of key code and byte of mirror key code.
Correct data
0x86 0x6B 0x00 0xFF
Wrong data
0x86 0x6B 0x00 0x00
This patch added additional test of mirror byte for filtering.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds driver for 774 Friio White, ISDB-T USB receiver
Friio White is an USB 2.0 ISDB-T receiver. (http://www.friio.com/)
The device has a GL861 chip and a Comtech JDVBT90502 canned tuner module.
This driver ignores all the frontend_parameters except frequency,
as ISDB-T shares the same parameter configuration across the country
and thus the device can work like an intelligent one.
As this device does not include a CAM nor hardware descrambling feature,
the driver passes through scrambled TS streams.
There is Friio Black, a variant for ISDB-S, which shares the same USB
Vendor/Product ID with White, but it is not supported in this driver.
They should be identified in the initialization sequence,
but this feature is not tested.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for Earthsoft PT1
Eearthsoft PT1 is a PCI card for Japanese broadcasting with two ISDB-S
and ISDB-T demodulators.
This card has neither MPEG decoder nor conditional access module
onboard. It transmits only compressed and possibly encrypted MPEG data
over the PCI bus, so you need an external software decoder and a
decrypter to watch TV on your computer.
This driver is originally developed by Tomoaki Ishikawa
<tomy@users.sourceforge.jp> by reverse engineering.
[mchehab@redhat.com: renamed isdb_ts to isdbs_ts to use the current standard]
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In ISDB-S, time-devision duplex is used to multiplexing several waves
in the same frequency. Each wave is identified by its own transport
stream ID, or TS ID. We need to provide some way to specify this ID
from user applications to handle ISDB-S frontends.
This code has been tested with the Earthsoft PT1 driver.
[mchehab@infradead.org: Fix merge conflicts with isdbt and rename the new parameter to DTV_ISDBS_TS_ID]
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/gspca/gl860/gl860.c: In function ‘gl860_build_control_table’:
drivers/media/video/gspca/gl860/gl860.c:119: warning: ‘sd_ctrls’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/saa7164/saa7164-buffer.c: In function ‘saa7164_buffer_alloc’:
drivers/media/video/saa7164/saa7164-buffer.c:110: warning: cast to pointer from integer of different size
drivers/media/video/saa7164/saa7164-buffer.c:112: warning: cast to pointer from integer of different size
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Following changes done for vpif driver to support vpif capture:-
1) Current version of display driver defined vpif register
space as part for vpif display platform driver resource
This is not correct since vpif is common across capture
and display drivers. So the resource iomap function is
moved to this module
2) Since there are common registers, a spinlock is added for
mutual exclusion.
This has incorporated comments against version v0 of the patch series
Resending to merge to V4L linux-next
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the vpif capture bridge driver for DM6467. This video
supports two video channels each having a tvp5147 device at
the input. This allows simultaneous capture of NTSC/PAL video
in each of this channel. Both MMAP and USERPTR io mechanism
are supported. Currently buffer allocation happens at REQBUF
ioctl request. Since USERPTR IO is supported, this is not an
issue since user applications can allocate buffers and pass
the user space address to the driver. Following are TODOs :-
1) Adding support for allocation of buffers at init
2) VBI/HBI data service
This has incorporated comments received against version v0
of the patch series.
Resending to merge V4l linux-next
create mode 100644 drivers/media/video/davinci/vpif_capture.c
create mode 100644 drivers/media/video/davinci/vpif_capture.h
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The structure name for vpif display driver changed since it was not unique. So this
update is done to reflect the same. Also removed the code related to register
address space iomap. Uses v4l2_i2c_new_subdev_board() instead of
v4l2_i2c_new_probed_subdev() so that platform data can be added for subdevice
configuration for polarities.
This has incorporated comments against version v0 of the patch series.
Resending the original patch for merge to V4L linux-next
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warn when the desired device node number is already in use, except when
the new video_register_device_no_warn function is called since in some
use-cases that warning is not relevant.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some subtle differences in the way the devnode numbers are
handled depending on whether the FIXED_MINOR_RANGES config option is
set. Add some simple wrapper functions to handle that correctly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The term 'kernel number' is very vague, so replace it with the somewhat more
descriptive term 'device node number'.
In one place the local variable 'nr' was used to create the device node number
of the new device name. This has been replaced with the vdev->num field to
more clearly mark this as being the device node number and not the minor
number.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_register_device_index is never actually called, instead the
stream index number is always calculated automatically.
This patch removes this function and simplifies the internal get_index
function since that can now always just return the first free index.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we are not using v4l2_device_call_* calls any more, we don't need to
initialise subdevice .grp_id any more. This also fixes compiler warnings on
64-bit platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the soc-camera interface for V4L2 subdevices thinner yet. Handle
gain and exposure internally in each driver just like all other controls.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unneeded soc-camera operations, this also makes the soc-camera API to
v4l2 subdevices thinner.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial soc-camera scaling and cropping implementation turned out to be
incompliant with the V4L2 API, e.g., it expected the user to specify cropping
in output window pixels, instead of input window pixels. This patch converts
the soc-camera core and all drivers to comply with the standard.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_subdev_call() instead of v4l2_device_call_until_err() in all host
drivers and in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove set_crop soc-camera device method and switch to s_crop from v4l2-subdev
video operations. Also extend non-i2c drivers to also hold a pointer to their
v4l2-subdev instance in control device driver-data, i.e., in
dev_get_drvdata((struct device *)to_soc_camera_control(icd))
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use host-side image scaling when the client fails to set the requested format.
We also have to take scaling into account when performing host-side cropping.
Similar to cropping we try to use client-side scaling as much as possible to
preserve bus bandwidth and optimise the frame-rate.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current tw9910 driver does not implement cropping correctly. Therefore, and
also because various rectangles in struct soc_camera_device are in user scale,
we cannot and shall not use rect_current as window location.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OV772x sensors cannot crop, they only support two fixed formats: VGA and QVGA.
We should not change the format when requested to crop, only S_FMT can do this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prohibit S_FMT and S_CROP with a different window width or height after video
buffer initialisation. This simplifies the work to be done in specific host and
client drivers, and it doesn't seem to make much sense to allow these changes.
We do however allow S_CROP with equal width and height to just move the window,
this doesn't affect video buffer management and is usually easy enough to
implement.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API mandates, that drivers do not update the argument of the S_CROP
ioctl() with the actual geometry. Comply.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all video capture devices can configure arbitrary cropping, whereas the
CEU module on SuperH CPUs can crop with pixel precision. However, we want to
use camera cropping if possible to save bandwidth and increase the frame-rate.
This patch verifies whether the camera managed to crop exactly the requested
rectangle, and if not, uses host-side cropping. To be able to crop on CEU we
have to preserve camera rectangle too, for which the host_priv member in
struct soc_camera_device is used. We now allocate memory dynamically, thus we
have to use the .put_formats() method from struct soc_camera_host_ops to free
it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch
[PATCH] video: use videobuf_waiton() in sh_mobile_ceu free_buffer()
was not quite correct. It closed a race, but introduced a potential
lock-up, if for some reason an interrupt does not come. This has been
observed in tests with tw9910. This patch safely dequeues buffers without
waiting for their completion. It also moves a buffer state assignment
under a spinlock to make it atomic with queuing of the buffer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The move of format translation initialisation into soc_camera_open() was
temporary for the soc-camera as platform driver intermediate step, put it back
into soc_camera_probe(). Also add a .put_formats() method to
soc_camera_host_ops to free any resources host driver might have allocated in
.get_formats().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 drivers are allowed to configure a geometry different than what has been
requested by the user with S_CROP, but then they have to adjust the input
rectangle accordingly. Fix ov772x to comply with this requirement.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. soc-camera always requests a valid rectangle, when calling .s_fmt(), no need
to check and adjust
2. in .s_crop(), if the rectangle exceeds sensor limits, push it to the
respective border instead of centering
3. take into account left and top borders when checking
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to using struct v4l2_rect in struct soc_camera_device for uniformity and
simplicity.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the V4L2_CID_SHARPNESS control to switch SH-mobile camera low-pass filter.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now soc-camera only supported client (sensor) controls. This patch
enables camera-host drivers to implement their own controls too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_BAND_STOP_FILTER control is used to switch the "Banding Filter" on
OV772x cameras on and off and to set the minimum AEC value in BDBASE register.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the soc-camera framework to use the v4l2-(sub)dev API. Start using
v4l2-subdev operations. Only a part of the interface between the
soc_camera core, soc_camera host drivers on one side and soc_camera device
drivers on the other side is replaced so far. The rest of the interface
will be replaced in incremental steps, and will require extensions and,
possibly, modifications to the v4l2-subdev code.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all drivers to platform device API. We already
converted platforms to register a platform device for each soc-camera client,
now we remove the compatibility code and switch completely to the new scheme.
This is a preparatory step for the v4l2-subdev conversion.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_platform.c is only used by y SuperH ap325rxa board. This patch
converts soc_camera_platform.c and its users for the soc-camera platform-
device conversion and also extends soc-camera core to handle non-I2C cameras.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the platform header file, the subdev_info structure name has been changed
to vpif_subdev_info. Update this change in the driver too.
Applies to v4l-dvb repository.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new module added for vpss library functions that are
used for configuring vpss system module. All video drivers will
include vpss.h header file and call functions defined in this
module to configure vpss system module.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the hw module for DM644x CCDC. This registers with the
vpfe capture driver and provides a set of hw_ops to configure
CCDC for a specific decoder device connected to the VPFE.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds ccdc hw module for DM355 CCDC. This registers with the bridge
driver a set of hw_ops for configuring the CCDC for a specific
decoder device connected to vpfe.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This the vpfe capture bridge driver for doing video
capture on DM355 and DM6446 evms. The ccdc hw modules register with the
driver and are used for configuring the CCD Controller for a specific
decoder interface. The driver also registers the sub devices required
for a specific evm. More than one sub devices can be registered.
This allows driver to switch dynamically to capture video from
any sub device that is registered. Currently only one sub device
(tvp5146) is supported. But in future this driver is expected
to do capture from sensor devices such as Micron's MT9T001, MT9T031
and MT9P031 etc. The driver currently supports MMAP based IO.
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mutex_lock_interruptible return value has to be handled properly to indicate
the status to the higher layers of the kernel.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Makefile and Kconfig changes for DM646x Video Display device, using
davinci/vpif, adv7343 and ths7303 drivers.
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code be used by the display and capture drivers.
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Red and blue gain isn't handled in conformance with the v4l2 specification. Disable them for now.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't set blue and red gain during init as we manuall set it later
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We manually set the gain later, no need to do it during init
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the default exposure value is set at startup
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SAA7164: Remove the SAA7164 bus id, no longer required.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following build warning:
CC [M] saa7164-core.o
saa7164-core.c: In function 'saa7164_buffer_deliver':
saa7164-core.c:113: warning: passing argument 2 of 'dvb_dmx_swfilter_packets'
from incompatible pointer type
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for NXP TDA18271 as a standalone tuner, allowing the use of
analog demodulators other than the Philips/NXP TDA829x.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
increase BULK transfer size from 512 to 8192 to increase wakeups
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card uses the same cx23885 gpio lines for two adapters.
In case of there is several cards in system we must implement
gpio mutex per cx23885 chip.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for Reddo DVB-C USB TV Box device. Remote is not working yet.
Thanks to Benjamin Larsson <banan@ludd.ltu.se>
Cc: Benjamin Larsson <banan@ludd.ltu.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_G_STD ioctl may not be present in the case of radio receivers.
In that case G_STD will return an error. The v4l1-compat layer should not
attempt to propagate that error to the caller, instead it should be
ignored.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SAA7164: Add support for a new HVR-2250 hardware revision
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SAA7164: Ensure the HVR-2200 second tuner is configured in slave mode.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that by default all tuners are set correctly to master/slave mode.
For all HVR2250's, ensure slave based tuners are caliberated during attach
to avoid locking problems on tuner# above channel 91.
HVR2200 tuner attach time to be reviewed in a future patch.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases we're seeing large timeouts on commands. I'm changing the
implementation so that the deferred worker checks the PCI bus for
any messages and signals the waiting caller accordingly. The previous
mechanism was too unreliable.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firmware typically responds in < 50ms and, via the interrupts and
deferred work queue the caller (blocked in the driver) is signalled very
efficiently. In a highly stressed system this can take many multiples
of seconds. So, we need a larger maximum timeout for busy systems.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup a printk and output two helpful driver params in debug mode.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's timing out and aborting firmware load too quickly on some
platforms, this increases the upper limit.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for all of the known shipping Hauppauge HVR-2200
and HVR-2250 boards. Digital TV ATSC/QAM and DVB-T is enabled at this
time. Both tuners are supported.
Volatiles and typedefs need rework, the rest is coding style compliant.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is fixing the initialization of the channel search parameters.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patchs adds support for the DiB8000 based devices STK807xP and
STK807xPVR to the dib0700-device-tree.
[mchehab@redhat.com: Fix merge conflicts]
Signed-off-by: Olivier Grenie <Olivier.Grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds support for the DiB8000 ISDB-T demodulator made by DiBcom.
Signed-off-by: Olivier Grenie <Olivier.Grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to follow a little bit the kernel coding style from now on
after the generation of that driver file and indent -linux call is
emitted.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
General update of the dib0070-driver based on DiBcom's latest release.
New driver features can enable better performance in some reception situations.
Signed-off-by: Patrick Boettcher <Patrick.Boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was forgotten to map the LAYER_ENABLED ioctl to the frontend-cache and back.
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch increments the DVB-API to version 5.1 in order to reflect the addition of ISDB-T and ISDB-Tsb on Linux' DVB-API.
Changes in detail:
- added a small document to describe how to use the API to tune to an ISDB-T or ISDB-Tsb channel
- added necessary fields to dtv_frontend_cache
- added a smarter clear-cache function which resets all fields of the dtv_frontend_cache
- added a TRANSMISSION_MODE_4K to fe_transmit_mode_t
Signed-off-by: Olivier Grenie <olgrenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since there is now correct support for the DiB7770 the support for the
'Terratec Cinergy T USB XXS (HD)' can be added.
One USB-ID has been moved, another one has been added.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for the dib7770P and the STK7770P
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the SNR monitoring for the dib7000p. The result is in dB.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c-kbd-i2c allows a bridge driver to pass information about IR configuration,
but uses a "void *" to pass along what is essentially constant data. This
change casts a const * to a void * to remove the warning.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some emacs tags from em28xx-vbi.c, which were copied from cx88-vbi.c,
per Mauro Carvalho Chehab's request.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some codingstyle issues introduced during the addition of em28xx VBI
support. The patch makes no functional changes other than converting a few
debug printk() statements to em28xx_isocdbg.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a few codingstyle issues introduced when I was adding the VBI support to
the em28xx driver.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MSI GX700 is a tricky machine to support. Some revisions do need the sensor flipped, but not all.
Add another quirk, distinguished by its BIOS date.
Signed-off-by: Brian Kloppenborg <bkloppenborg@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add vflip quirk for the Fujitsu Siemens Amilo Pa 2548
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed one value and removed a duplicate in tda18271_cid_target[],
based on table 54 "CID_Target_map" in Rev.04 of the TDA18271HD datasheet.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the tda18271c2_rf_tracking_filters_correction function to include
the modified temperature compensation calculatation formula as described
in Rev.04 of the TDA18271HD datasheet.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't display "no agc configuration provided" unless DBG_ADV is set.
Fix comments in function, tda18271_agc. This config variable is not
for LNA configuration -- it is for external AGC configuration.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Display function parameters, idx and len, in error log.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the case of multiple tuner instances, ensure that non-default
configuration options are saved into the driver's state.
This resolves an issue where a configuration option may not be
carried into the driver if the analog side of a hybrid driver
initializes before the digital side.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
minor cleanup: move small_i2c assignment to the state config block
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For better readability, treat the low power standby mode configuration
as an output option feature configuration, and change it to a bitmask.
If left unconfigured, all features will remain enabled, just as the
default configuration was before these changes were introduced.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By default, the driver enters standby mode with slave tuner output
loop thru enabled and xtal oscillator on.
Not all designs require that slave tuner output loop thru and
xtal oscillator remain active while in standby mode, so two
additional standby modes have been added:
- standby mode with xtal oscillator on (loop thru off)
- total power off
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And mask should be 0xff00 instead of 0xae00.
Thanks to Jochen Friedrich <jochen@scram.de> for pointing this.
Cc: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* define names for few values
* decrease buffer len by one byte which was not used
* add check for buffer overflow for sure
* indentation fixes
* remove useless 0 len check from memcpy
It should not happen and if it happens memcpy should not do anything.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix wrongly configured USB1.1 TS EP.
Patch serie also increases USB URB size to reduce wakeups.
USB1.1 URB size from 64 to 940 bytes
USB2.0 URB size from 512 to 16356 bytes
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unused variable from when I introduced the g_std() function.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove redundant call to set the vinctrl register. This eliminates any
ambiguity as to how the register is configured (since it is now always set in
em28xx_set_outfmt).
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to implement the g_std call, or else the default norm always gets
returned, which breaks VBI capturing if you had changed the standard to NTSC
using s_std.
I had temporarily changed the default norm to NTSC so that zvbi-ntsc-cc
wouldn't choke, so now that we are returning the correct value, switch it back
to PAL as the default.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the code so we only claim to support VBI if the underlying chipset
actually has the support.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not create the VBI device in cases where VBI is not supported on the target
em28xx chip.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current locking infrastructure didn't support having multiple fds accessing
the device (such as video and vbi). Rework the locking infrastructure,
borrowing the design from cx88.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding support for both video and VBI, I missed the mmap ioctl. Add
the missing call.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for raw VBI capture for the em28xx bridge, currently only for
NTSC. Support for PAL capture to follow shortly (including the removal of
numerous hard-coded NTSC-specific sizes for capture buffers, etc).
Note that the code currently changes the default current norm from PAL to
NTSC (so that zvbi-ntsc-cc works properly). The default norm really should
be moved into a board-level parameter.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code enabling the VBI registers for variants of the em28xx chip that
support VBI, and make sure the isoc streaming code continues to work for
the video component of the stream (note the video and vbi data arrive
intermixed on the same isoc pipe).
Note that this version just drops the actual VBI data onto the floor as
opposed to processing it. The "#ifdef 0" tags are for the videobuf code that
appears in the next patch in this series.
We created a separate version of the isoc_copy version for parsing the version
of the stream that includes VBI data. In theory, they might be able to be
merged at some point in the future, but the initial goal is to ensure that we
do not cause any regressions with devices that do not have VBI support.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly document the video input control register, in preparation for the
addition of VBI support. Note this patch makes no functional changes.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added Kworld DVD Maker 2
Thanks to C Western <l@c-m-w.me.uk> for reporting this board.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
There are some extra parenthesis at the clauses, and some switch() tests
for boards that don't have i2c ir. Remove those extra code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the logic to load ir i2c ancillary module is broken. It is
associated to Hauppauge devices with IR flag on their eeprom, no matter
if the device uses i2c or em28xx direct IR support. That's wrong.
Instead, add a flag to the boards that use i2c IR chips and load the
module only for those devices and if ir is not disabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.
Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.
Before this patch, if ir-kbd-i2c were probed after SAA7134, trash data
were used.
Compile tested only, but the patch is identical to em28xx one. So, it
should work properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at ir-kbd-i2c
module load), than the lifetime of a struct IR_i2c_init_data allocated off of
the stack in cx18_i2c_new_ir() at registration time. Make sure we pass
a pointer to a persistent IR_i2c_init_data object at i2c registration time.
Thanks to Brian Rogers for pointing out a solution, and Dustin Mitchell for
testing against a 2.6.30 kernel.
Reported-by: Dustin Mitchell <soxslayer@gmail.com>
Reported-by: Brian Rogers <brian@xyzw.org>
Tested-by: Dustin Mitchell <soxslayer@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.
Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.
Before this patch, if ir-kbd-i2c were probed after em28xx, trash data
were used. After the patch, no matter what order, it is properly
reported as tested by me:
input: i2c IR (i2c IR (EM2840 Hauppaug as /class/input/input10
ir-kbd-i2c: i2c IR (i2c IR (EM2840 Hauppaug detected at i2c-4/4-0030/ir0 [em28xx #0]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using the MT9M111's IFP to handle exposure/gain gives better results.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use s16 instead of int where possible.
Use struct instead of arrays
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes broken exposure on SOI968 webcams that was causing
the camera to display a black screen
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let 0c45:60fc in sn9c102 and 0c45:613e in gspca-sonixj (sensor not supported).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new exchanges are taken from the information file of the ms-win driver
(usbvm326.inf - webcam 15b8:6002).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check the modulation in dvb_frontend_check_parameters against
frontend's capabilties for FE_QAM devices.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various frontend driver have parameter checks in their set_frontend
functions and return an error if the parameters are not supported,
tda10021 and cx24116 to name two.
The tuning ioctls FE_SET_FRONTEND/FE_SET_PROPERTY only change values
in the property cache and return before set_frontend is called. If a
set_frontend call in software zigzag algorithm fails and the card was
previously locked it will report a lock and the new parameters but is
still tuned to the old transport. This is not detectable from
userspace.
This change checks the return values of fe->ops.set_frontend and
changes the state to the added FESTATE_ERROR for software zigzag.
No lock will be reported to userspace if the State is FESTATE_ERROR.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for more than 8 DVB devices is requested regularly so make it
a kconfig variable instead of a header define. Values in the range 4-32
are tested.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Add one more vivitar mini cam to the list of CIF cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Allow overriding of detected sensor type
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Use correct register for CIF type 1 sensor gain settings
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Add controls for CIF type 0 sensor cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: make the probing a bit less chatty
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Move detection of CIF sensor type to probe() function,
so that the right controls are set to disabled from the start, rather then
having them disappear all of a sudden when the stream is started.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: cleanup/fixup control handling
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca: mr97310a fix detection of sensortype for vivicam with id byte of 0x53
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds supports for mr97310a camera's with CIF sensors (2 different
types) and for VGA mr97310a camera with a different sensor then supported
until now.
This patch also add support for controls for one of the 2 CIF sensors, this
was written by Thomas Kaiser <thomas@kaiser-linux.li>
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Thomas Kaiser <thomas@kaiser-linux.li>
Signed-off-by: Hans de Goede <hdgoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we've figured out the higher compression settings (supported in
libv4l-0.6.0 and later, so after this patch the driver should be used with
libv4l-0.6.0 or higher only!), we can enable higher framerates. Which
means lower exposure times, which is important for the use of the pac207
in full daylight.
This patch also tweakes the brightness default and the per color gain
balances to use the values which are adviced by Pixart in the pac207
application note.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_pac207: remove a number of unneeded (repeated) register writes
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the model there are three different firmwares to choose from.
Unfortunately if a cx23885 is loaded first, then the global firmware name
is overwritten with that firmware and if ivtv is loaded next, then it
tries to load the wrong firmware. In addition, the original approach would
also overwrite any firmware that the user specified explicitly.
Cc: Jarod Wilson <jarod@wilsonet.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The compiler warned about an uninitialized stereo variable. By simplifying
the code it 1) improved readability and 2) fixed the compiler warning.
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The input subsystem checks if get_keycode works for a scan code. Due to that,
we need to return a valid value when there's some space at the table that
can be used by a scancode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implements handler for EVIOCGKEYCODE/EVIOCSKEYCODE via adding two new callbacks
to the input device.
Since on dvb-usb a scan code has 16 bits, to fulfill rc5 standard codes, the default
getkeycode/setkeycode input methods would require the driver to spend up to 64 Kb of
a sparse table. Instead, add two new callbacks to the event device.
With this, it is now possible to replace the keycode tables. There are, however, a few
implementation details at the current patch:
1) It will replace the existing device keytable, instead of creating an instance
of the data. This works. However, if two devices pointing to the same table
were connected, changing the IR table of one will also change the IR table for
the other (the solution for this one is simple: just kmalloc some memory);
2) In order to change the scan code, you need first to change the key to
KEY_RESERVED or KEY_UNKNOWN to free some space at the table (solution: allocate
some additional space for newer scan codes or allow dynamic table grow);
3) The table size cannot be extended. It would be easy to allow the table to
grow dynamically: just calling kmalloc(size+1); kfree(old). Yet, maybe we can
just create a bigger table with a fixed size, like for example a table with 128
entries. This should be enough even for a very big IR.
The current issues should be addressed on a later patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to be closer to V4L IR implementation, it is needed to replace
u8 custom, data
to:
u16 scan
This allows using non-rc5 mappings, like the 8 bit keycodes used on older
protocols. It will also allow future implementations of rc6 keystrokes
when needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- bad sensor power
- bad edge gain/threshold
- set back the auto gain
- light frequency filter inverted
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support for RoverMedia TV Link Pro FM (LR138 REV:I) card
based on saa7134.
Signed-off-by: Eugene Yudin <Eugene.Yudin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support our new TV card based on xc5000 and saa7134.
Analog TV works well.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch introduces new snd_saa7134_capsrc_set (code taken from
snd_saa7134_capsrc_put) that updates also the ALSA capture controls during
snd_card_saa7134_capture_prepare and snd_saa7134_capsrc_put.
There can be much more work done in order to unify the control of the card
(now the card's capture source is tuned/switched in saa7134-video.c too), but
I don't have enough time. This work could be a starting point, but it can be
applied as-is too (it doesn't need any further work to make it working).
Signed-off-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hello kernel developers.
I found a bug report from an user in launchpad. I just copy it here. It
includes patch.
I don't own the necessary hardware to test it but the patch looks
trivial.
I'm not subscribed to this list, so please CC me. Thanks!
Here is the text:
"""
remote control for my tv card doesnt work
I have Askey CPH03x TV Capturer.
When I load bttv module with "card=59" option which is proper for this
tv card,
I can watch tv with sound but my remote control doesnt work. There is no
ir
event in /proc/bus/input/device .
When bttv module is loaded with "card=137" option remote control works
very
well.
$ cat /proc/bus/input/devices
.......
........
: Bus=0001 Vendor=109e Product=0350 Version=0001
N: Name="bttv IR (card=137)"
P: Phys=pci-0000:00:0d.0/ir0
S: Sysfs=/devices/pci0000:00/0000:00:0d.0/input/input144
U: Uniq=
H: Handlers=kbd event6
B: EV=100003
B: KEY=2c0814 100004 0 0 0 4 2008000 2090 2001 1e0000 4400 0 ffc
Unfortunately there is no sound.
"""
https://bugs.launchpad.net/ubuntu/+bug/239733http://bugzilla.kernel.org/show_bug.cgi?id=11995
--
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card is reported as YUAN High-Tech Development Co., Ltd STK7700D
[mchehab@redhat.com: fix merge conflicts and properly name USB PID]
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: James A Webb <jamesawebb@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
applications tend to check the signal strength very often. This patch
enables users to select which AVC messages to log using a bitmask. In
addition, it also enables the possibility to debug application PMTs sent
to the driver. This will be usable since the CA support is still poorly
tested for lots of CAMs and CA systems.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On certain master / slave dual tuner configurations, tuning performance
improves when the RF tracking filter calibration is performed sequentially.
This patch allows for the bridge driver to specify this behavior in the
configuration structure at attach-time.
The "cal" module option will continue to override this attach-time
configuration: set cal=0 to prevent RF tracking filter calibration
on startup, and set cal=1 to force it.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove excess spacing from the tda_foo printk macros & line things up better
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename dprintk to tda_dprintk to be consistent with the other tda_foo macros.
Move KERN_DEBUG facility level to tda_dprintk.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the bandwidth to be less than 8 MHZ and greater than 6 MHZ is logically
impossible.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support to AverMedia Studio 505
[dougsland@redhat.com: fixed rejects and removed the change to add dk as default secam variant]
[mchehab@redhat.com: fix a few CodingStyle issues]
Signed-off-by: Vasiliy Temnikov <vaka@newmail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
KEY_CAMERA is already used for a long time with webcam drivers to take a picture.
On other media drivers, due to the lack of a snapshot button, random KEY codes
were sent, being KEY_SHUFFLE the most used one, probably due to cut-and-paste
from other remotes, since one of them uses the same key for snapshot and shuffle.
The better is to use KEY_CAMERA on all drivers solving this issue. This
follows the IR standard map as defined at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use standard definitions for channel controls, as defined at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
While here, fix a few broken up/down/left/right mappings
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Each remote were using a different keycode for timeshift. Use the same
keycode for all of them, using the map as defined at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several IR's that were using IR to type a letter that it is
known by some random application. Instead, the better is to use
the standard definitions found at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
And, if needed, submit a patch for the application to understand the
media keys.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While we're still discussing it, let's point to the wiki page. In
the future, this should be added at V4L2 API spec DocBooks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make Checkpatch tool happy:
-:2349: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
On all cases, it were just a blank line at the wrong place. Yet, fixing it is trivial
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir-keymaps.c has frequent additions. As people tend to copy an old
keyboard entry, a bad CodingStyle at an ancient entry may result on a
freshly bad CodingStyle patch.
So, better to fix the CodingStyle for the entire file.
This patch is the first of a series of patches fixing it, generated by
some perl magic plus manual handling.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds files to control si4713 devices.
Internal functions to control device properties
and initialization procedures are into these files.
Also, a v4l2 subdev interface is also exported.
This way other drivers can use this as v4l2 i2c subdevice.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds files which creates the radio interface
for si4713 FM transmitter (modulator) devices.
In order to do the real access to device registers, this
driver uses the v4l2 subdev interface exported by si4713 i2c driver.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds basic configurations for FM TX extended controls.
That includes controls names, menu strings, pointer identification,
type classification and flags configuration.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The upcoming RDS encoder needs support for string controls. This patch
implements the core implementation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the recent improvements we don't need to probe anymore, if we know
the i2c address of the receiver.
The address of the receiver for the remote with the gray buttons is not
confirmed anywhere, but it is very unlikely to see it on something else.
We want to have that information anyway.
BTW, those remaining still probing, please join.
Signed-off-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes an unneeded power management primitive.
Power management is automatically enabled as probe ends.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several reasons:
- SAA7133/35 uses DDEP (DemDec Easy Programming mode), which works in 32kHz
only
- SAA7134 for TV mode uses DemDec mode (32kHz)
- Radio works in 32kHz only
- When recording 48kHz from Line1/Line2, switching of capture source to TV
means switching to 32kHz without any frequency translation
Signed-off-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Acked-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I just happen to peek inside the PWC driver and did not like what I saw
there. Please consider applying the patch below.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It does matter to set explicitly gpio0 value in
cx88_board structure for TBS 8920 card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Makes zl10353 a bit more DVB API compliant:
FE_READ_UNCORRECTED_BLOCKS - keep a counter of UNC blocks
FE_GET_FRONTEND - return last set frequency instead of zero
Signed-off-by: Aleksandr V. Piskunov <alexandr.v.piskunov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AVC protocol uses the same command for tuning and PID filtering and
since dvb-core uses a software zigzagging to do automatic retuning this
could cause all PID filters to be cleared. PID filter information is
now included in all DSD commands to the card.
Background:
There is a problem in the firedtv driver that causes recordings to stop
if the SW zigzag algorithm in dvb-core kicks in with a retune after the
application has set up the PID filters. Since tuning and setting PID
filters uses the same AVC command (DSD) and only the replace subfunction
is supported by the card, it is not possible to do a retune without
setting the PID filters. This means that the PID filtering has to be
sent in each tune.
This problem applies to C and T cards since S and S2 cards tune using a
vendor specific command. The patch corrects the problem by sending the
PID list in each tune. I have tested it on my T card with a good
result.
How to trigger problem: Zap to a channel and output AV to a file, e.g.
"tzap -c channels.conf SVT1 -r -o SVT1.ts". After a short while, pull
the antenna cable from the card. The lock on the channel will disappear
and the TS file will stop increasing in size. Wait a couple of seconds.
Replug the cable again. You will get a lock on the channel again, but
the TS file will never increase in size agains sinze no PIDS are
filtered.
Tested with kaffeine with DVB-T and DVB-C: Fixes retuning after antenna
was plugged out and back in with DVB-T. Does not fix this with DVB-C,
but also doesn't regress on DVB-C.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which fixes tuning to low frequency channels with
stb0899+tda8261 cards like the KNC TV-Station DVB-S2.
The cause of the issue was a broken if construct, which should have been
an if/else if, so that the setting for the lowest matching frequency is
applied.
Without this patch for example tuning to "arte" on Astra 19.2, 10744MHz
SR22000 failed most times and when it failed the communication between
driver and tda8261 was completely broken.
This problem disappears with the attached patch.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID (1b80:e400) for KWorld PlusTV Dual DVB-T Stick (DVB-T 399U).
The model number on the devices sticker label is "KW-DVB-T 399UR".
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems from other code that it is the dst_type field rather than the
type_flags field that contains values of the form DST_TYPE_IS...
The type_flags field contains values of the form DST_TYPE_HAS...
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ struct dst_state E; @@
(
*E.type_flags ==
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
|
*E.type_flags !=
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
)
// </smpl>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Humax/Coex DVB-T USB Stick 2.0 High Speed
which is a very popular tuner sold in Vietnam.
Tested with at least 3 tuners.
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The changeset 0b17d0ed that aded ASUSTeK P7131 Analog were using
7 spaces instead of tab, probably due to some bad cut-and-paste.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On VIDEO_M52790 and USB_GSPCA_SN9C20X, instead of tab, it were
using 7 whitespaces at the beginning, probably due to some
cut-and-paste trouble.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch solves problem of missed keystrokes on some remote controls,
as reported on http://bugzilla.kernel.org/show_bug.cgi?id=9637 .
Signed-off-by: Andrzej Hajda <andrzej.hajda@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card includes Intel ce5039(Zarlink zl10039) tuner
and Intel ce6313 (Zarlink zl10313) demod.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code from Jan D. Louw with some minor changes.
http://article.gmane.org/gmane.linux.drivers.dvb/38163
Tested with TeVii S630 DVB-S USB card by me (Igor)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Robert P.J. Day for finding this.
Thanks-to: Robert P.J. Day <rpjday@crashcourse.ca>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I updated and simplyfied patch from Zbynek Hrabovsky for recent kernel.
It enables autodetection of card, sound in analog TV , sound in FM radio
and switching between antenna and cable RF input. Radio tuner still
doesn't work, I don't even know how it works. Some guys wrote me that FM
radio works with TV tuner used instead of radio part (symlink video0 ->
radio0).
Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Vlastimil Labsky <vlasta.labsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
do_div requires an u64 as the first argument, not a s64.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use unified lgs8gxx frontend instead of reverse engineered lgs8gl5 frontend.
After this patch, lgs8gl5 frontend could be mark as deprecated.
Future development should base on unified lgs8gxx frontend.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error handling code following a kmalloc should free the allocated data.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have support for radio on saa7133/35/31e cards with tda8290/8275(a)
and 5.5MHz ceramic filter on the bridge chips since a while.
It was previously not tested, if this card supports it too, but the old
"ghost" radio with wrong filters doesn't work anymore.
Thanks go to Pham Thanh Nam and Laszlo Kustan for reporting it working
on that input.
Signed-off-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Define correct tuner in config. Radio now works fine
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The structure and comments of the I2C part have been adopted to fit to the
USB part.
Some additional cleanups and precisements have been made to the version
detection and checking functionality to clearly separate HW/SW/FW version.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch supports i2c interface of si470x. The i2c specific part
exists in radio-si470x-i2c.c file and the common part uses
radio-si470x-common.c file. The '#if defined' is inserted inevitably
because of parts used only si470x usb in the common file.
The current driver version doesn't support the RDS.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The si470x_disconnect_check is function to check disconnect state of
radio in common file. The function is implemented in each interface
file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is for using dev_* macro instead of printk.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is a preceding work to add the i2c interface of si470x.
The si470x directory includes a common file and usb specific file and
header file.
The part unrelated with usb interface and i2c interface exists in
radio-si470x-common.c file, and The usb specific part exists in
radio-si470x-usb.c file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[tobias.lorenz@gmx.net: Small changes, due to new include "linux/smp_lock.h"]
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the STK7700D USB-DVB-Device.
lsusb identifies it as:
idVendor 0x1164 YUAN High-Tech Development Co., Ltd
idProduct 0x1efc
iProduct 2 STK7700D
The device is build into a Samsung R55-T5500 notebook.
Signed-off-by: Pete Hildebrandt <send2ph@googlemail.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restructure the UVC descriptors parsing code to handle multiple streaming
interfaces. The driver now creates a uvc_video_chain instance for each chain
detected in the UVC control interface descriptors, and tries to register one
video device per streaming endpoint.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards multiple streaming interfaces support, reorganize the
driver's data structures to cleanly separate video control and video streaming
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API (chapter 1.5) states that:
Drivers must implement all input ioctls when the device has one
or more inputs, all output ioctls when the device has one or more outputs.
When the device has any audio inputs or outputs the driver must set the
V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
VIDIOC_QUERYCAP ioctl.
So, devices without audio input should return -EINVAL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are many lock imbalances in this driver. Fix all found.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There seems to be one superfluos unlock in a poll function. Remove it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The irq handler will touch memory. Even in the error case some URBs may
complete. Thus no memory must be kfreed before all URBs are killed.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Zilog Z8F0811 IR transceiver chips on
CX2341[68] based boards to ir-kbd-i2c for both the old i2c binding model
and the new i2c binding model.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support to the cx18 driver for setting up the
Z8F0811/Hauppauge IR Tx/Rx chip with the i2c binding model in newer
kernels.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Functions which are referenced by their address can't be inlined by
definition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au0828-dvb driver uses bulk usb transfers for digital transport,
but the debug reports, "iso xfer already running!\n".
Fix this to report bulk instead of isoc.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents a loop if a permanent error occurs in usb_set_interface().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patches
gspca - vc032x: Add resolution 1280x1024 for sensor mi1310_soc.
gspca - vc032x: Webcam 041e:405b added and mi1310_soc updated.
will make the preview function not work, so I disable the 1280x1024 resolution
and revert back to the origin mi1310_soc settings.
And, using USB snoop tool on Windows to get the correct i2c commands to
turn on/off the LED flash.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* use i2c_w instead of reg_w
* return error on failure
* read the correct number of bytes
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After the i2c subdev changes the ordering of initialization changed,
causing a total loss of previous GPIO settings and a loss of DTV.
The generic firmware loading routine has now changed to preserve
GPIO values if the device is cx23885 based (safety) and I've
moved the GPIO configuration from probe() into the cx23885 init
func which is a little clearer and fixes the bug.
Tested-by: Sohail Syyed <linuxtv@hubstar.net>
Reviewed-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even devices without ac97 needs to call analog audio setup function, to
properly set xclk and mute/unmute.
Thanks to Angelo Cano <acano@fastmail.fm> for reporting and testing it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace printing to magically sized temporary buffer with use
of KERN_CONT for continual printing of eeprom registers dump.
Since deb_info is defined as dprintk, which is conditionally defined
to printk without additional parameters, meaning that deb_info is equivalent
to direct printk (without adding KERN_ facility), we can use KERN_DEBUG and
KERN_CONT in there, eliminating the need for sprintf into temporary buffer
with not easily readable/magical size.
Though it's strange, that deb_info definition uses printk without KERN_
facility and callers don't use it either.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the subdev_s_std() method from the GPIO subdev. It appears it was
used in the past to effect the switch back from radio mode to tuner mode,
but it had a side effect that is improper and against the V4L2 spec, when
you were not in radio mode. Whenever the video stanadrd was changed, the
GPIO audio mux was set back to the tuner audio input, even if you were set
to a Line In input.
Thanks to Ravi A. for doing the troubleshooting to point me right to the
problem.
Reported-by: Ravi A <asvravi@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
