To optimise data storage redundant vars are removed.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of users have complained that their syslog often shows this
messages but it doesn't impact performance. I'm changing this to a debug
message, so developers will still see the message during testing and
users will no longer be bothered by this.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This add initial configuration for radio support on the
hvr-3000/4000. FM radio doesn't work as yet without
further patches (to come), but this prepares for
that.
Experimental radio support shows that it works
when combined with additional audio routing
work for cards with an FMD1216ME analogue
frontend, but not the MEX variant (more later).
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds audio routing on the hvr-3000/4000
This is a preliminary patch for later routing
requirements.
This adds line-in support on the 2 cards mentioned.
It is also apparent that there is an initial open
fault for line-in when opening composite/s-video.
This will be fixed later.
It was also noticed that the bit-field for audio
routing which was 2 bits needs an increase as
the WM8775 for example, allows a value 4 bits
wide for it's audio mux.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This add frontend R/W mutual exclusion.
Prior to this point in time it was possible to open both
frontends simultaneously which an MFE card cannot support.
In order to stop this, a delayed open is performed which
has the following function:
- Return EBUSY after a configurable amount of time
if a frontend is unavailable due to the other being
in use.
- Only allow opening of a frontend if the kernel thread
of the other has stopped.
This solution was chosen to allow switching between
frontends to work as seamlessly as possible. When both
frontends are actually opened simultaneously then one
will only open, but if quick switching is performed
between one of many then the new open will succeed in
a clean fashion rather than interrupting a kernel
thread.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx22702 is now always reset on module load. Prior to
this the cx22702 was not found on i2c scan without a
full reset.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a configurable (one per card) gate control option
for multi-frontend. Prior to this point gate control was
assumed to be on the primary frontend, this is a fault
when the gate to the analogue section is on the secondary
which is the default for both the HVR-3000 and HVR-4000
in MFE.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of reference to videobuf_dvb_get_frontend used an invalid
index. This has been fixed.
The section for the HVR3000 in advise_acquire was redundant as
the same logic is used on the HVR4000. This has been removed
and both cards now use the same function.
A number of small errors and whitespace errors are also fixed.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A detailed description from the original patches 2 years ago:
"The WinTV-HVR3000 has a single transport bus which is shared between
a DVB-T and DVB-S modulator. These patches build on the bus acquisition
cx88 work from a few weeks ago to add support for this.
So to applications the HVR3000 looks like this:
/dev/dvb/adapter0/fe0 (cx24123 DVB-S demod)
/dev/dvb/adapter0/fe1 (cx22702 DVB-T demod)
Additional boards continue as before, eg:
/dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod)
The basic change is removing the single instance of the videobuf_dvb in
cx8802_dev and saa7134_dev(?) and replacing it with a list and some
supporting functions.
*NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so
two or three current cx88 patches appear to be reversed by this tree,
this will be cleaned up in the near future. The patches missing change
the mutex handing to core->lock, fix an enumeration problem."
It should be recognised that a number of people have been maintaining
this patchset. Significant levels of Kudos to everyone one involved,
including but not limited to:
Darron Broad
Fabio M. Di Nitto
Carlo Scarfoglio
Hans Werner
Without the work of these people, and countless others, my two year old
patches would of died on the Mercurial linuxtv.org vine a long time
ago.
TODO: Revise these patches a little further so that the need for
demux1 and dvr0 is optional, not mandatory on the HVR3000.
HISTORY (darron):
This is the last update to MFE prepared by Hans which is based
upon the `scratchpad' diff created by Carlo.
All MFE work prior to that point must be attributed to Fabio
who ported and maintained Steve's original patch up to that
time.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for Prof 7300 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
[mchehab@redhat.com: fixed CARDLIST.cx88 entry]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Well, one thing you encouraged me to do was re-test some of my cards
which contained the xc3028-zarlink combo.
Which led me to test a Dvico FusionHDTV Pro.
Almost a year ago, Chris Pascoe did a patch for this which can be found
at his ~pascoe/xc-test at Linuxtv.
This worked very well, however that was using his version of firmware.
Alas, someone attempted to use this and patch v4l-dvb, and messed it up.
So I've fixed it.
I enclose the patch against today's tree (containing your latest
tuner-xc2028.c patch).
The card now works very well, well with DVB-T anyway.
Signed-off-by: Tim Farrington <timf@iinet.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From the author:
"This fixes the problem where previously all client disconnects
put the analogue frontend into standby.
In the following example, the first command is succesfully
watching TV but the second command which returns EBUSY
detunes the receiver by entering it into the standby state.
tvtime -d /dev/video0 &
cat /dev/video0
"
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch against latest mercurial makes DVB-T working on Pinnacle
Hybrid PCTV Pro (pctv310c).
In cx88-dvb.c, a specific zl10353_config is created with the if2
inferred from the old comment in the currently used config. It is then
used for attach, and i2c_gate_ctrl is set to NULL.
The entry in cx88-cards.c is modified with GPIO gathered from windows
with regspy, and DVB enabled. The frontend is set to
XC3028_FE_ZARLINK456 to match the zl10353_config.
It is working great with the freeview channels I can receive.
Signed-off-by: Stéphane Voltz <stef.dev@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sidney Matias <sidney.matias@gmail.com> for getting GPIO
values and testing on this device.
Cc: Sidney Matias <sidney.matias@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for ST STV0288 demodulator and cards with it,
such as TeVii S420.
Patch is co-authored with Georg Acher <acher@baycom.de>
Signed-off-by: Georg Acher <acher@baycom.de>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for TBS 8920 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for Omicom SS4 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From the author:
This patch-set fixes remote control issues I have experienced
with hauppauge drivers in Linux since the PVR-350 and now
with both a NOVA-S+ and HVR-4000. It has also been confirmed
to work with an HVR-1300 user who had exactly the same issue.
Hauppage remote controls use RC5. RC5 has a bit-field which
represents the target device. The hauppauge windows drivers
have a registry key which can enable filtering, but the linux
drivers will accept any target device in this bit field for
internal processing.
This causes problems with setups such as mythtv where remote
control key presses destined for the TV (target = 0) are
interpreted by the kernel and subsequenctly LIRC then mythtv.
Of the remote controls I have to hand (wintv black, pvr/hvr
silver) the hauppauge remotes send one of two device targets
ids, these are interpreted by the patch which then filters
out any non hauppauge addresses.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the debugging sysctls.
Rolloff was broken, not it works as expected and has been tested in kaffeine.
Power related changes for the isl6421 are not implemented on the HVR4000/4000LITE.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for TeVii S460 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding support for Hauppauge's cx88 S2 based products, based on the
cx24116 DVB-S2 demodulator.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dont pass devptr in xc5000_attach, dont store it in xc5000_priv.
This pointer is passed into the tuner_callback function, which always
expects a pointer to fe->dvb->priv or i2c_adapter->algo_data.
This prevents future possible bugs in new drivers, such as using a "devptr"
other that the standard fe->dvb->priv in a DVB driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL is now moved from the video_open function in v4l2-dev.c to the
various drivers. It seems about a third of the drivers already has a
lock of some sort protecting the open(), another third uses
video_exclusive_open (yuck!) and the last third required adding the
BKL in their open function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 135aedc38e, as
requested by Hans Verkuil.
It was a patch for 2.6.28 where the BKL was pushed down from v4l core to
the drivers, not for 2.6.27!
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit d9b19199e4
(always enable FW_LOADER unless EMBEDDED=y) we can remove
the FW_LOADER select's and corresponding dependencies
on HOTPLUG.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The type and type2 fields were unused and so could be removed.
Instead add a vfl_type field that contains the type of the video
device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All ioctl callbacks are now stored in a new v4l2_ioctl_ops struct. Drivers fill in
a const struct v4l2_ioctl_ops and video_device just contains a const pointer to it.
This ensures a clean separation between the const ops struct and the non-const
video_device struct.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Converted the last users of audiochip.h to the v4l2-chip-ident.h header
and remove the now unused audiochip.h header.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The functions in a header should not belong to another module. The prio functions
belong to v4l2-common.c, so move them to v4l2-common.h.
The ioctl functions belong to v4l2-ioctl.c, so create a new v4l2-ioctl.h header
and move those functions to it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The field 'dev' is not the video device, but the parent of the video device.
Rename accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also remove some blank lines that were used to split compat code at -devel
tree.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx18 can support transport streams with newer firmwares. Add a TS
capability to the generic cx2341x module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The naming for the callbacks that handle the VIDIOC_ENUM_FMT and
VIDIOC_S/G/TRY_FMT ioctls was very confusing. Renamed it to match
the v4l2_buf_type name.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current code passes a context pointer in the xc5000_config struct.
This context pointer is used in the tuner_callback function, used to
reset the device after firmware download.
The xc5000_config struct is a static structure, whose .priv member was
being assigned before calling xc5000_attach(). If there are more than
one of the same device type installed on a single system, the last one
to assign xc5000_config.priv will "win", and all others will cease to
function properly.
This patch passes the context pointer in xc5000_attach() rather that
storing it within the static struct xc5000_config.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88 doesn't need support for FW_LOADER. Instead, this is required only for
cx88-blackbird.
Also, cx88-blackbird depends on HOTPLUG, due to FW_LOADER dependency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_TUNER is responsible for compilation of tuners.ko module. This were the
previous behaviour before the creation of MEDIA_TUNER.
Before this patch, tuner.ko were created even for drivers that don't need a
tuner (like webcam drivers).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
