When allocating memory for the kernel image, try the AllocatePages()
boot service to obtain memory at the preferred offset of
'dram_base + TEXT_OFFSET', and only revert to efi_low_alloc() if that
fails. This is the only way to allocate at the base of DRAM if DRAM
starts at 0x0, since efi_low_alloc() refuses to allocate at 0x0.
Tested-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since both CONFIG_ACPI and CONFIG_OF are enabled when booting using ACPI
tables on ARM64 platforms, we get few device tree warnings which are not
valid for ACPI boot. We can use of_have_populated_dt to check if the
device tree is populated or not before throwing out those errors.
This patch uses of_have_populated_dt to remove non legitimate device
tree warning when booting using ACPI tables.
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are cases where we want to compile out both versions of an
alternative code block, so add an enable parameter to the new conditional
alternative assembly macros in the same way as alternative_insn.
Signed-off-by: Will Deacon <will.deacon@arm.com>
'Privileged Access Never' is a new arm8.1 feature which prevents
privileged code from accessing any virtual address where read or write
access is also permitted at EL0.
This patch enables the PAN feature on all CPUs, and modifies {get,put}_user
helpers temporarily to permit access.
This will catch kernel bugs where user memory is accessed directly.
'Unprivileged loads and stores' using ldtrb et al are unaffected by PAN.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
[will: use ALTERNATIVE in asm and tidy up pan_enable check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The system register encoding generated by sys_reg() works only
for MRS/MSR(Register) operations, as we hardcode Bit20 to 1 in
mrs_s/msr_s mask. This makes it unusable for generating instructions
accessing registers with Op0 < 2(e.g, PSTATE.x with Op0=0).
As per ARMv8 ARM, (Ref: ARMv8 ARM, Section: "System instruction class
encoding overview", C5.2, version:ARM DDI 0487A.f), the instruction
encoding reserves bits [20-19] for Op0.
This patch generalises the sys_reg, mrs_s and msr_s macros, so that
we could use them to access any of the supported system register.
Cc: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some uses of ALTERNATIVE() may depend on a feature that is disabled at
compile time by a Kconfig option. In this case the unused alternative
instructions waste space, and if the original instruction is a nop, it
wastes time and space.
This patch adds an optional 'config' option to ALTERNATIVE() and
alternative_insn that allows the compiler to remove both the original
and alternative instructions if the config option is not defined.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When a new cpu feature is available, the cpu feature bits will have some
initial value, which is incremented when the feature is updated.
This patch changes 'register_value' to be 'min_field_value', and checks
the feature bits value (interpreted as a signed int) is greater than this
minimum.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds an 'enable()' callback to cpu capability/feature
detection, allowing features that require some setup or configuration
to get this opportunity once the feature has been detected.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Later patches need config_sctlr_el1 to set/clear bits in the sctlr_el1
register.
This patch moves this function into header a file.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the dynamic patching for ARM64_HAS_SYSREG_GIC_CPUIF over to
the newly added alternative assembler macros.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the dynamic patching for ARM64_WORKAROUND_845719 over to
the newly added alternative assembler macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the dynamic patching for ARM64_WORKAROUND_CLEAN_CACHE over to
the newly added alternative assembler macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The existing alternative_insn macro has some limitations that make it
hard to work with. In particular the fact it takes instructions from it
own macro arguments means it doesn't play very nicely with C pre-processor
macros because the macro arguments look like a string to the C
pre-processor. Workarounds are (probably) possible but things start to
look ugly.
Introduce an alternative set of macros that allows instructions to be
presented to the assembler as normal and switch everything over to the
new macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Based on arch/arm/include/asm/cputype.h, this function does the
shifting and sign extension necessary when accessing cpu feature fields.
Signed-off-by: James Morse <james.morse@arm.com>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Most of the cache events an architecture might support do not map well
to those provided by the ARM architecture, and as such most entries in
the event number maps are *_UNSUPPORTED. Unfortuantely as 0 is a valid
physical event identifier, the *_UNSUPPORTED macros expand to a non-zero
value and thus each unsupported event must be explicitly initialised as
such. This leads to large diffs when adding support for a new CPU, and
makes it difficult to spot the important information.
This patch follows arch/arm/ in making use of PERF_*_ALL_UNSUPPORTED
macros to initialise all entries to *_UNSUPPORTED before overriding this
for the specific events we actually support, resulting in a significant
source code reduction.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Remove paragraph about writing to the Free Software Foundation's
mailing address from GPL notice.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The default dma_common_get_sgtable() implementation relies on the CPU
address of the buffer being a regular lowmem address. This is not always
the case on arm64, since allocations from the various DMA pools may have
remapped vmalloc addresses, rendering the use of virt_to_page() invalid.
Fix this by providing our own implementation based on the fact that we
can safely derive a physical address from the DMA address in both cases.
CC: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: made static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Nobody seems to be producing !SMP systems anymore, so this is just
becoming a source of kernel bugs, particularly if people want to use
coherent DMA with non-shared pages.
This patch forces CONFIG_SMP=y for arm64, removing a modest amount of
code in the process.
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently bundle the callchain handling code with the PMU code,
despite the fact the two are distinct, and the former can be useful even
in the absence of the latter.
Follow the example of arch/arm and factor the callchain handling into
its own file dependent on CONFIG_PERF_EVENTS rather than
CONFIG_HW_PERF_EVENTS.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The AArch64 instruction set contains load/store pair memory accessors,
so use these in our copy_*_user routines to transfer 16 bytes per
iteration.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The compat ptrace interface allows access to the TLS register, hardware
breakpoints and watchpoints, syscall number. However, a native task
using the native ptrace interface to debug compat tasks (e.g. multi-arch
gdb) only has access to the general and VFP register sets. The compat
ptrace interface cannot be accessed from a native task.
This patch adds a new user_aarch32_ptrace_view which contains the TLS,
hardware breakpoint/watchpoint and syscall number regsets in addition to
the existing GPR and VFP regsets. This view is backwards compatible with
the previous kernels. Core dumping of 32-bit tasks and compat ptrace are
not affected since the original user_aarch32_view is preserved.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Yao Qi <yao.qi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Plumb up Makefile arguments for the already supported formats in the kbuild
system: lz4, bzip2, lzma, and lzo.
Note that just as with Image.gz, these images are not self-decompressing and
the booting firmware still needs to handle decompression before launching the
kernel image.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARMv8.1 architecture extensions introduce support for hardware
updates of the access and dirty information in page table entries. With
TCR_EL1.HA enabled, when the CPU accesses an address with the PTE_AF bit
cleared in the page table, instead of raising an access flag fault the
CPU sets the actual page table entry bit. To ensure that kernel
modifications to the page tables do not inadvertently revert a change
introduced by hardware updates, the exclusive monitor (ldxr/stxr) is
adopted in the pte accessors.
When TCR_EL1.HD is enabled, a write access to a memory location with the
DBM (Dirty Bit Management) bit set in the corresponding pte
automatically clears the read-only bit (AP[2]). Such DBM bit maps onto
the Linux PTE_WRITE bit and to check whether a writable (DBM set) page
is dirty, the kernel tests the PTE_RDONLY bit. In order to allow
read-only and dirty pages, the kernel needs to preserve the software
dirty bit. The hardware dirty status is transferred to the software
dirty bit in ptep_set_wrprotect() (using load/store exclusive loop) and
pte_modify().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 68234df4ea ("arm64: kill flush_cache_all()") removed
soft_reset() from the kernel. This was the only caller of
setup_mm_for_reboot(), so remove that also.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Brown reported an allnoconfig build failure in -next:
Today's linux-next fails to build an arm64 allnoconfig due to "mm:
make GUP handle pfn mapping unless FOLL_GET is requested" which
causes:
> arm64-allnoconfig
> ../mm/gup.c:51:4: error: implicit declaration of function
'update_mmu_cache' [-Werror=implicit-function-declaration]
Fix the error by moving the function to asm/pgtable.h, as is the case
for most other architectures.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit 9d3bfbb4df ("arm64: Combine coherent and non-coherent
swiotlb dma_ops"), __dma_common_mmap is no longer shared between two
callers, so roll it into the remaining one.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 68234df4ea ("arm64: kill flush_cache_all()") removed the
only users of these macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
arch_find_n_match_cpu_physical_id parses the device tree to get the
device node for a given logical cpu index. However, since ARM PMUs get
probed after the CPU device nodes are stashed while registering the
cpus, we can use of_cpu_device_node_get to avoid another DT parse.
This patch replaces arch_find_n_match_cpu_physical_id with
of_cpu_device_node_get to reuse the stashed value directly instead.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 pmu prints an error message in event_init() when
no hardware PMU is available. This is pretty annoying as
it keeps printing the message for every single trial, flooding
the kernel logs, unnecessarily. The return code is sufficient for
the user to figure out the reason.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull perf fix from Thomas Gleixner:
"A single fix for the intel cqm perf facility to prevent IPIs from
interrupt context"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/cqm: Return cached counter value from IRQ context
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- the manual revert of the SYSCALL32 changes which caused a
regression
- a fix for the MPX vma handling
- three fixes for the ioremap 'is ram' checks.
- PAT warning fixes
- a trivial fix for the size calculation of TLB tracepoints
- handle old EFI structures gracefully
This also contains a PAT fix from Jan plus a revert thereof. Toshi
explained why the code is correct"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Revert 'Adjust default caching mode translation tables'
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
x86/mm: Fix newly introduced printk format warnings
mm: Fix bugs in region_is_ram()
x86/mm: Remove region_is_ram() call from ioremap
x86/mm: Move warning from __ioremap_check_ram() to the call site
x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
x86/mm/pat: Adjust default caching mode translation tables
x86/fpu: Disable dependent CPU features on "noxsave"
x86/mpx: Do not set ->vm_ops on MPX VMAs
x86/mm: Add parenthesis for TLB tracepoint size calculation
efi: Handle memory error structures produced based on old versions of standard
Toshi explains:
"No, the default values need to be set to the fallback types,
i.e. minimal supported mode. For WC and WT, UC is the fallback type.
When PAT is disabled, pat_init() does update the tables below to
enable WT per the default BIOS setup. However, when PAT is enabled,
but CPU has PAT -errata, WT falls back to UC per the default values."
Revert: ca1fec58bc 'x86/mm/pat: Adjust default caching mode translation tables'
Requested-by: Toshi Kani <toshi.kani@hp.com>
Cc: Jan Beulich <jbeulich@suse.de>
Link: http://lkml.kernel.org/r/1437577776.3214.252.camel@hp.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here are a number of small serial and tty fixes for reported issues.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlW0QW4ACgkQMUfUDdst+ym7UwCglnDVjGrWiw29PU42rXROq/Vf
6boAniJehd4f/U9r5+aw/Hx6jqrhwC6c
=dfFk
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small serial and tty fixes for reported issues.
All have been in linux-next successfully"
* tag 'tty-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: Fix !TASK_RUNNING diagnostic warning from paste_selection()
serial: core: Fix crashes while echoing when closing
m32r: Add ioreadXX/iowriteXX big-endian mmio accessors
Revert "serial: imx: initialized DMA w/o HW flow enabled"
sc16is7xx: fix FIFO address of secondary UART
sc16is7xx: fix Kconfig dependencies
serial: etraxfs-uart: Fix release etraxfs_uart_ports
tty/vt: Fix the memory leak in visual_init
serial: amba-pl011: Fix devm_ioremap_resource return value check
n_tty: signal and flush atomically
- Fix a reference inbalance issue for power_ro_lock_show() sysfs handler
MMC host:
- omap_hsmmc: Fix IRQ errorhandling for CD, DTO, and CRC
- sdhci: Prevent a kernel panic while using DMA
- mtk-sd: Let it depend on HAS_DMA to prevent build errors
- sdhci-esdhc: Make 8BIT bus work
- sdhci-esdhc-imx: Fix some regressions for DT based platforms
- sdhci-pxav3: Fix a regression for DT based platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Bk8L
-----END PGP SIGNATURE-----
Merge tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.2 rc4.
Note, most of the changes are for the sdhci-esdhc-imx controller,
which also required us to modify some related DTS files. Those
changes have been acked by the SoC maintainer.
MMC core:
- Fix a reference inbalance issue for power_ro_lock_show() sysfs handler
MMC host:
- omap_hsmmc: Fix IRQ errorhandling for CD, DTO, and CRC
- sdhci: Prevent a kernel panic while using DMA
- mtk-sd: Let it depend on HAS_DMA to prevent build errors
- sdhci-esdhc: Make 8BIT bus work
- sdhci-esdhc-imx: Fix some regressions for DT based platforms
- sdhci-pxav3: Fix a regression for DT based platforms"
* tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pxav3: fix platform_data is not initialized
dts: mmc: fsl-imx-esdhc: remove fsl,cd-controller support
mmc: sdhci-esdhc-imx: clear f_max in boarddata
mmc: sdhci-esdhc-imx: remove duplicated dts parsing
mmc: sdhci: make max-frequency property in device tree work
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
dts: imx7: fix sd card gpio polarity specified in device tree
dts: imx25: fix sd card gpio polarity specified in device tree
dts: imx6: fix sd card gpio polarity specified in device tree
dts: imx53: fix sd card gpio polarity specified in device tree
dts: imx51: fix sd card gpio polarity specified in device tree
mmc: sdhci-esdhc: Make 8BIT bus work
mmc: block: Add missing mmc_blk_put() in power_ro_lock_show()
mmc: MMC_MTK should depend on HAS_DMA
mmc: sdhci check parameters before call dma_free_coherent
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
mmc: omap_hsmmc: Fix DTO and DCRC handling
Pull arch/tile bugfix from Chris Metcalf:
"This fixes a bug in freeing the initramfs memory"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use free_bootmem_late() for initrd
This change reverts most of commit 53e9accf0f 'Do not use R9 in
SYSCALL32'. I don't yet understand how, but code in that commit
sometimes fails to preserve EBP.
See https://bugzilla.kernel.org/show_bug.cgi?id=101061
"Problems while executing 32-bit code on AMD64"
Reported-and-tested-by: Krzysztof A. Sobiecki <sobkas@gmail.com>
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Will Drewry <wad@chromium.org>
Cc: Kees Cook <keescook@chromium.org>
CC: x86@kernel.org
Link: http://lkml.kernel.org/r/1437740203-11552-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit c627f2ceb6 ("serial: 8250: Add support for big-endian MMIO accesses")
added support for 32-bit big-endian mmio to the 8250 driver. Support for
ioreadXXbe/iowriteXXbe io accessors was missing from m32r arch, which caused
build errors.
Add trivial macro mmio accessors.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were previously using free_bootmem() and just getting lucky
that nothing too bad happened.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: stable@vger.kernel.org
Make them clearly architecture-dependent; the capability is valid for
all architectures, but the argument is not.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF depends on WB to boot fast, because it only clears caches after
it has set up MTRRs---which is too late.
Let's do writeback if CR0.CD is set to make it happy, similar to what
SVM is already doing.
Signed-off-by: Xiao Guangrong <guangrong.xiao@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic of the disabled_quirks field usually results in a double
negation. Wrap it in a simple function that checks the bit and
negates it.
Based on a patch from Xiao Guangrong.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_mtrr_get_guest_memory_type never returns -1 which is implied
in the current code since if @type = -1 (means no MTRR contains the
range), iter.partial_map must be true
Simplify the code to indicate this fact
Signed-off-by: Xiao Guangrong <guangrong.xiao@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
