On IVB hardware we are given an interrupt whenever a L3 parity error
occurs in the L3 cache. The L3 cache is used by internal GPU clients
only. This is a very rare occurrence (in fact to test this I need to
use specially instrumented silicon).
When a row in the L3 cache detects a parity error the HW generates an
interrupt. The interrupt is masked in GTIMR until we get a chance to
read some registers and alert userspace via a uevent. With this
information userspace can use a sysfs interface (follow-up patch) to
remap those rows.
Way above my level of understanding, but if a given row fails, it is
statistically more likely to fail again than a row which has not failed.
Therefore it is desirable for an operating system to maintain a lifelong
list of failing rows and always remap any bad rows on driver load.
Hardware limits the number of rows that are remappable per bank/subbank,
and should more than that many rows detect parity errors, software
should maintain a list of the most frequent errors, and remap those
rows.
V2: Drop WARN_ON(IS_GEN6) (Jesse)
DRM_DEBUG row/bank/subbank on errror (Jesse)
Comment updates (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that gen3 is the only platform where we've got the bit
definitions right, hence the workaround of disabling sdvo hotplug
support on i945g/gm is not due to misdiagnosis of broken hotplug irq
handling ...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: add some blurb about sdvo hotplug fail on i945g/gm I've
wondered about while reviewing.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also as we set the HOTPLUG_EN to 0 during pre-install, we can simply set
it during post-install, and nor do we wish to enable unwanted hotplug
events.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.
Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.
Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.
v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell interrupts are mostly similar with Ivy Bridge, so we share same
routines with it.
This patch also simplifies the vblank counter handling for all the Gen5+
architectures.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can take advantage that the PCH_IIR is a subordinate register to
reduce one of the required IIR reads, and that we only need to clear
interrupts handled to reduce the writes. And by simply tidying the code
we can reduce the line count and hopefully make it more readable.
v2: Split out the bugfix from the refactoring.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only half of them even cared, and it's always the same one.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- reduce the irq disabled section, even for a debugfs file this was
way too long.
- always disable irqs when taking the lock.
v2: Thou shalt not mistake locking for reference counting, so:
- reference count the error_state to protect from concurent freeeing.
This will be only really used in the next patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and hide it in i915_dma.c.
This way all the legacy stuff dealing with READ_BREADCRUMB and
LP_RING and friends is in i915_dma.c.
v2: Rebase on top of Chris Wilson's rework irq handling code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just get this out of the way.
v2: Rebase against ENODEV changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never supported dri1 on gen5+.
VLV never had that code, so no need to remove it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_dma.c contains most of the old dri1 horror-show, so move
the remaining bits there, too. The code has been removed and
the only thing left are some stubs to ensure that userspace
doesn't try to use this stuff. vblank_pipe_set only returns 0
without any side-effects, so we can even stub it out with
the canonical drm_noop.
v2: Rebase against ENODEV changes.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vblank_pipe was intended to be used for tracking DRI1 state. However,
the vblank_pipe reported to DRI1 is fixed to umask both pipes, and the
dev_priv->vblank_pipe unused and superfluous.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The waiting_seqno is not terribly useful, and as such we can remove it
so that we'll be able to extract lockless code.
v2: Keep the information for error_state (Chris)
Check if ring is initialized in hangcheck (Chris)
Capture the waiting ring (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: add some bikeshed to clarify a comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This extra bit of interrupt enabling code doesn't belong in the wait
seqno function. If anything we should pull it out to a helper so the
throttle code can also use it. The history is a bit vague, but I am
going to attempt to just dump it, unless someone can argue otherwise.
Removing this allows for a shared lock free wait seqno function. To keep
tabs on this issue though, the IER value is stored on error capture
(recommended by Chris Wilson)
v2: fixed typo EIR->IER (Ben)
Fix some white space (Ben)
Move IER capture to globally instead of per ring (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: ier is a 16 bit reg on gen2!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since there is only one remaining user of I915_INTERRUPT_ENABLE_FIX,
expand it at the callsite. Quoting Jesse Barnes:
"I'd really like to get rid of these defines at the top of i915_irq.c.
Some are unused and the others just make you check for the right bits
everytime your read the code."
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add bikeshed suggested by Jesse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We appear to allow too many pending pageflips as evidenced by an
apparent pin-leak. So borrow the pageflip completion logic from i8xx for
handling PendingFlip in a robust manner.
v2: Address Jesse's reminders about the nuances of gen3 IRQ handling.
References: https://bugzilla.kernel.org/show_bug.cgi?id=41882
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bring the for-each-pipe loops together so that the code is easier on the
eyes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple of miscellaneous cleanups as well to move per-loop condition
variables within the scope of the loop and the update of the DRI1
breadcrumb to the tail of the function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And a couple of miscellaneous cleanups to the main body of the IRQ loop;
move per-loop condition variables within the scope of the loop and move
the old DRI1 breadcrumb to the tail of the function and so only execute
it once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On later gen3, you are able to select the meaning of the FlipPending
status bit in IIR and change it to FlipDone. This was sometimes done by
the BIOS leading to confusion on just how pageflipping worked on gen3.
Simplify the implementation by using the legacy meaning for all gen3
machines.
Note: this makes all gen3 machines equally broken...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for rewriting the gen3 irq handler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And remove the cargo-culted copy from the valleyview irq handler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The waitqueues are already initialised during ring initialisation so
kill the redundant and duplicated code to do so in each generations IRQ
installer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than duplicate similar code across the IRQ installers, perform
the initialisation of the workers upfront. This will lead to simpler
teardown and quiescent code as we can assume that the workers have
been initialised.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calling these when gem assumes full control of the hw won't end
in anything else than tears. So be a bit more paranoid here.
Just serves as documentation.
v2: Bail out with ENODEV as suggested by Chris Wilson.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplify object tracking by removing the inactive but pinned list. The
only place where this was used is for counting the available memory,
which is just as easy performed by checking all objects on the rare
occasions it is required (application startup). For ease of debugging,
we keep the reporting of pinned objects through the error-state and
debugfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and put them to so good use.
Note that there's functional change in vlv clock gating code, we now
no longer spuriously read back the current value of the bit. According
to Bspec the high bits should always read zero, so ORing this in
should have no effect.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gen2 hardware has some significant differences from the other interrupt
routines that were glossed over and then forgotten about in the
transition to KMS. Such as
- 16bit IIR
- PendingFlip status bit
This patch reintroduces a handler specifically for gen2 for the purpose
of handling pageflips correctly, simplifying code in the process.
v2: Also fixup ring get/put irq to only access 16bit registers (Daniel)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24202
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41793
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: use posting_read16 in intel_ringbuffer.c and kill _driver
from the function names.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The purpose of this patch is to avoid zeroing the lower 12 reserved bits
of surface base address registers (framebuffer & sprite). There are bits
in that range that may occasionally be set by BIOS or by other components.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function, along with the registers and deferred work hander, are
all shared with SandyBridge, IvyBridge and their variants. So remove the
duplicate code into a single function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the first instance we just wish to kick the waiters and see if that
terminates the wait conditions. If it does not, then we do not want to
keep retrying without ever making any forward progress and becoming
stuck in a hangcheck loop.
Reported-and-tested-by: Lukas Hejtmanek <xhejtman@fi.muni.cz>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48209
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It exists way back to gen2, bug got moved around on gen4 a bit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv, ivb and snb all share the gen6+ gt irq handling. 3 copies of the
same stuff is a bit much, so extract it into a little helper.
Now ilk has a different gt irq handling than snb, but shares the same
irq handler (due to the similar display block). So also extract the
ilk gt irq handling to clearly separate these two things.
Nice side effect of this is that we can complete Ben Widawsky's gen6+
irq bit #define cleanup and call the render irq also with the GEN6
alias. Beforehand that code was shared with ilk, and neither option
really made much sense.
As a bonus this enables the error interrupt handling lifted from the
vlv code on snb and ivb, too.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Antagonized-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This got copy-pasted from an older version. The newer kinds of
workarounds don't need this anymore.
Shame on me for not noticing when picking up the vlv irq patch.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- gen6 put/get only need one argument
rflags and gflags are always the same (see above explanation)
- remove a couple redundantly defined IRQs
- reordered some lines to make things go in descending order
Every ring has its own interrupts, enables, masks, and status bits that
are fed into the main interrupt enable/mask/status registers. At one
point in time it seemed like a good idea to make our functions support
the notion that each interrupt may have a different bit position in the
corresponding register (blitter parser error may be bit n in IMR, but
bit m in blitter IMR). It turned out though that the HW designers did us
a solid on Gen6+ and this unfortunate situation has been avoided. This
allows our interrupt code to be cleaned up a bit.
I jammed this into one commit because there should be no functional
change with this commit, and staging it into multiple commits was
unnecessarily artificial IMO.
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet:
- fixed up merged conflict with vlv changes.
- added GEN6 to GT blitter bit, we only use it on gen6+.
- added a comment to both ring irq bits and GT irq bits that on gen6+
these alias.
- added comment that GT_BSD_USER_INTERRUPT is ilk-only.
- I've got confused a bit that we still use GT_USER_INTERRUPT on ivb
for the render ring - but this goes back to ilk where we have only
gt interrupt bits and so we be equally confusing if changed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ValleyView has a new interrupt architecture; best to put it in a new set
of functions. Also make sure the ring mask functions handle ValleyView.
FIXME: fix flipping; need to enable interrupts and call prepare/finish
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And track the existence of such a binding similar to the aliasing
ppgtt case. Speeds up binding/unbinding in the common case where we
only need a ppgtt binding (which is accessed in a cpu coherent fashion
by the gpu) and no gloabl gtt binding (which needs uc writes for the
ptes).
This patch just puts the required tracking in place.
v2: Check that global gtt mappings exist in the error_state capture
code (with Chris Wilson's llc reloc patches batchbuffers are no longer
relocated as mappable in all situations, so this matters). Suggested
by Chris Wilson.
v3: Adapted to Chris' latest llc-reloc patches.
v4: Fix a bug in the i915 error state capture code noticed by Chris
Wilson.
Reviewed-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use a more current logging style. Ensure that appropriate
logging messages are prefixed with "i915: ".
Convert printks to pr_<level>. Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that we can tally the request against the command sequence in the
ringbuffer, or merely jump to the interesting locations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Being able to tally the list of outstanding requests with the sequence
of commands in the ringbuffer is often useful evidence with respect to
driver corruption.
Note that since this is the umpteenth per-ring data structure to be added
to the error state, I've coallesced the nearby loops (the ringbuffer and
batchbuffer) into a single structure along with the list of requests. A
later task would be to refactor the ring register state into the same
structure.
v2: Fix pretty printing of requests so that they are parsed correctly by
intel_error_decode and use the 0x%08x format for seqno for consistency
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We still have reports of missed irqs even on Sandybridge with the
HWSTAM workaround in place. Testing by the bug reporter gets rid of
them with the forcewake voodoo and no HWSTAM writes.
Because I've slightly botched the rebasing I've left out the ACTHD
readback which is also required to get IVB working. Seems to still
work on the tester's machine, so I think we should go with the more
minmal approach on SNB. Especially since I've only found weak evidence
for holding forcewake while waiting for an interrupt to arrive, but
none for the ACTHD readback.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45181
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45332
Tested-by: Nicolas Kalkhof nkalkhof()at()web.de
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Back-merge from drm-fixes into drm-intel-next to sort out two things:
- interlaced support: -fixes contains a bugfix to correctly clear
interlaced configuration bits in case the bios sets up an interlaced
mode and we want to set up the progressive mode (current kernels
don't support interlaced). The actual feature work to support
interlaced depends upon (and conflicts with) this bugfix.
- forcewake voodoo to workaround missed IRQ issues: -fixes only enabled
this for ivybridge, but some recent bug reports indicate that we
need this on Sandybridge, too. But in a slightly different flavour
and with other fixes and reworks on top. Additionally there are some
forcewake cleanup patches heading to -next that would conflict with
currrent -fixes.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson and me have again stared at funny error states and it's
been pretty clear from the start that something was seriously amiss.
The seqnos last seen by the cpu were a few hundred behind those that
the gpu could have possibly emitted last before it died ...
Chris now tracked it down (hopefully, definit verdict's still out),
but in hindsight we'd have found the bug by simply dumping the cpu
side tracking of the ring head and tail registers.
Fix this and prevent an identical time-waster in the future.
Because the hangs always involved semaphores in one way or another,
we've tried to dump the mbox registers, but couldn't find any
inconsistencies. Still, dump them too.
Reviewed-and-wanted-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the buffer is not necessarily accessible through the GTT at the time
of a GPU hang, and capturing some of its contents is far more valuable
than skipping it, provide a clflushed fallback read path. We still
prefer to read through the GTT as that is more consistent with the GPU
access of the same buffer. So example it will demonstrate any errorneous
tiling or swizzling of the command buffer as seen by the GPU.
This becomes necessary with use of CPU relocations and lazy GTT binding,
but could potentially happen anyway as a result of a pathological error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
