This moves /proc/saa7164 to /sys/kernel/debug/saa7164.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Current clock scaling calculations are same for vpu4 and
previous versions. For vpu4, Clock scaling calculations
are updated with cycles/mb and bitrate. This helps in
getting precise clock required.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add vpp cycles for different types of codec.
It indicates the cycles required by video hardware
to process each macroblock. Add vsp cycles, cycles
required by stream processor. Initialize the codec
data with core resources.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Failure to suspend (venus_suspend_3xx) happens when the system
is fresh booted and loading venus driver. This happens once and
after reload the venus driver modules the problem disrepair.
Fix the failure by skipping the check for WFI and IDLE bits if
PC_READY is on in control status register.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This aims to add a requests for bandwidth scaling depending
on the resolution and framerate (macroblocks per second). The
exact value of the requested bandwidth is get from a
pre-calculated tables for encoder and decoder.
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In downstream driver, there are two frequency tables defined,
one for the encoder and one for the decoder:
/* Encoders /
<972000 490000000 0x55555555>, / 4k UHD @ 30 /
<489600 320000000 0x55555555>, / 1080p @ 60 /
<244800 150000000 0x55555555>, / 1080p @ 30 /
<108000 75000000 0x55555555>, / 720p @ 30 */
/* Decoders /
<1944000 490000000 0xffffffff>, / 4k UHD @ 60 /
< 972000 320000000 0xffffffff>, / 4k UHD @ 30 /
< 489600 150000000 0xffffffff>, / 1080p @ 60 /
< 244800 75000000 0xffffffff>; / 1080p @ 30 */
It shows that encoder always needs a higher clock than decoder.
In current venus driver, the unified frequency table is aligned
with the downstream decoder table which causes performance issues
in encoding scenarios. Fix that by aligning frequency table on
worst case (encoding).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The initial registers sequence is only loaded at probe
time. Afterward only the resolution and format specific
register are modified. Care must be taken to make sure
registers modified by one resolution setting are reverted
back when another resolution is programmed.
This was not done properly for the 720p case.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On some board it is possible that the sensor 'powerdown' and or 'reset'
pin might be controlled by gpio instead of being tied.
To implement we add pm_runtime support which will handle the power
up/down sequence when it is available otherwise the sensor will be
powered on at module insertion/probe and powered off at module removal.
Now originally the driver assumed that the sensor would always stay
powered and keep its register setting. We cannot assume this anymore, so
every time we "power up" we need to re-program the initial registers
configuration first. This was previously done only at probe time.
[Sakari Ailus: Resolve a conflict in Kconfig]
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add powerdown-gpios and reset-gpios to the list of optional properties
for the OV2659 camera sensor.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In ov2659_s_stream() return value for invoked function should be checked
and propagated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several of include files listed are not explicitly needed.
If they are need then they are implicitly included.
Reduce the list of includes to an easier to manage list.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure that if the expected sensor device id register
is not recognized properly the failure is propagated
up so devices are not left partially initialized.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on recently found sensor configuration examples, it was
discovered that when scaling and binning are used for the lower
resolutions (i.e. 640x480, 320x240) the read offset has to be
increased otherwise the image appears to be wrapped around.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for registering a sensor sub-device to the async
sub-device framework and parse set up common sensor related devices such as
actuator/VCM.
[Sakari Ailus: Rewrap commit message]
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Assign vep->link_frequencies to NULL after releasing its memory. Without
this change, multiple calls to v4l2_fwnode_endpoint_free() would result in
double kfree calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of individually depending on MEDIA_CAMERA_SUPPORT (or forgetting
it), put all camera sensor, lens and flash drivers under
MEDIA_CAMERA_SUPPORT as a whole. The lens VCM devices didn't use to do
this, but make them depend on MEDIA_CAMERA_SUPPORT as well since there's
no use for these devices without that in practice.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver stores crop rectangle settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, crop rectangle width and height settings are not updated
correctly when rectangle offset settings are applied on hardware. If
an error occurs while the device is updated, the stored settings my no
longer reflect hardware state and consecutive calls to .get_selection()
as well as .get/set_fmt() may return incorrect information. That in
turn may affect ability of a bridge device to use correct DMA transfer
settings if such incorrect informamtion on active frame format returned
by .get/set_fmt() is used.
Assuming a failed update of the device means its actual settings haven't
changed, update crop rectangle width and height settings stored in the
device private structure correctly while the rectangle offset is
successfully applied on hardware so the stored values always reflect
actual hardware state to the extent possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver stores frame format settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, those settings are updated before they are actually applied
on hardware. If an error occurs on device update, the stored settings
my not reflect hardware state anymore and consecutive calls to
.get_fmt() may return incorrect information. That in turn may affect
ability of a bridge device to use correct DMA transfer settings if such
incorrect informmation on active frame format returned by .get_fmt() is
used.
Assuming a failed device update means its state hasn't changed, update
frame format related settings stored in the device private structure
only after they are successfully applied so the stored values always
reflect hardware state as closely as possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not clear what pixel format is actually configured in hardware on
reset. MEDIA_BUS_FMT_YUYV8_2X8, assumed on device probe since the
driver was intiially submitted, is for sure not the one.
Fix it by explicitly applying a known, driver default frame format just
after initial device reset.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit da298c6d98 ("[media] v4l2: replace video op g_mbus_fmt by pad
op get_fmt") converted a former ov6650_g_fmt() video operation callback
to an ov6650_get_fmt() pad operation callback. However, the converted
function disregards a format->which flag that pad operations should
obey and always returns active frame format settings.
That can be fixed by always responding to V4L2_SUBDEV_FORMAT_TRY with
-EINVAL, or providing the response from a pad config argument, likely
updated by a former user call to V4L2_SUBDEV_FORMAT_TRY .set_fmt().
Since implementation of the latter is trivial, go for it.
Fixes: da298c6d98 ("[media] v4l2: replace video op g_mbus_fmt by pad op get_fmt")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
User arguments passed to .get/set_fmt() pad operation callbacks may
contain unsupported values. The driver takes control over frame size
and pixel code as well as colorspace and field attributes but has never
cared for remainig format attributes, i.e., ycbcr_enc, quantization
and xfer_func, introduced by commit 11ff030c73 ("[media]
v4l2-mediabus: improve colorspace support"). Fix it.
Set up a static v4l2_mbus_framefmt structure with attributes
initialized to reasonable defaults and use it for updating content of
user provided arguments. In case of V4L2_SUBDEV_FORMAT_ACTIVE,
postpone frame size update, now performed from inside ov6650_s_fmt()
helper, util the user argument is first updated in ov6650_set_fmt() with
default frame format content. For V4L2_SUBDEV_FORMAT_TRY, don't copy
all attributes to pad config, only those handled by the driver, then
fill the response with the default frame format updated with resulting
pad config format code and frame size.
Fixes: 11ff030c73 ("[media] v4l2-mediabus: improve colorspace support")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since its initial submission, the driver selects V4L2_COLORSPACE_JPEG
for supported formats other than V4L2_MBUS_FMT_SBGGR8_1X8. According
to v4l2-compliance test program, V4L2_COLORSPACE_JPEG applies
exclusively to V4L2_PIX_FMT_JPEG. Since the sensor does not support
JPEG format, fix it to always select V4L2_COLORSPACE_SRGB.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 4f996594ce ("[media] v4l2: make vidioc_s_crop const")
introduced a writable copy of constified user requested crop rectangle
in order to be able to perform hardware alignments on it. Later
on, commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video
ops") replaced s_crop() video operation using that const argument with
set_selection() pad operation which had a corresponding argument not
constified, however the original behavior of the driver was not
restored. Since that time, any hardware alignment applied on a user
requested crop rectangle is not passed back to the user calling
.set_selection() as it should be.
Fix the issue by dropping the copy and replacing all references to it
with references to the crop rectangle embedded in the user argument.
Fixes: 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit afd9690c72 ("[media] ov6650: convert to the control
framework"), if an error occurs during initialization of a control
handler, resources possibly allocated to the handler are not freed
before device initialiaton is aborted. Fix it.
Fixes: afd9690c72 ("[media] ov6650: convert to the control framework")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 23a52386fa ("media: ov6650: convert to standalone v4l2
subdevice") converted the driver from a soc_camera sensor to a
standalone V4L subdevice driver. Unfortunately, module description was
not updated to reflect the change. Fix it.
While being at it, update email address of the module author.
Fixes: 23a52386fa ("media: ov6650: convert to standalone v4l2 subdevice")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If CONFIG_REGMAP_I2C is not set, building fails:
drivers/media/i2c/max2175.o: In function `max2175_probe':
max2175.c:(.text+0x1404): undefined reference to `__devm_regmap_init_i2c'
Select REGMAP_I2C to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b47b79d8a2 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch converts the cx231xx driver to the vb2 framework.
Since you can't do a partial conversion this is a big-bang patch,
i.e. large and hard to review. I never found a way around this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Co-developed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for cec-notifier to the cec-gpio driver.
This makes it possible to associate the CEC gpio pin with an HDMI
connector. This feature was always documented in the cec-gpio bindings:
Documentation/devicetree/bindings/media/cec-gpio.txt
But support for the hdmi-phandle property was never actually implemented in
this driver.
This patch adds support for this property.
It also fixes a few incorrect error returns in the probe() function, which
skipped the call to cec_delete_adapter().
Tested on a Raspberry Pi 3B with a modified vc4 driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document the new CEC_ADAP_G_CONNECTOR_INFO ioctl and the new
CEC_CAP_CONNECTOR_INFO capability.
Co-developed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: added CEC_CAP_CONNECTOR_INFO]
[hverkuil-cisco@xs4all.nl: added DQEVENT have_conn_info]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Until now the connector info API was a kernel-internal API only.
This moves it to the public API and adds the new ioctl to retrieve
this information.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CEC_OP_REC_FLAG_NOT_USED is 0 and CEC_OP_REC_FLAG_USED is 1, not the
other way around.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Jiunn Chang <c0d1n61at3@gmail.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of hardcoding the UI Command key values, use the new
defines.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These defines were never added to this CEC header, likely due
to laziness on the part of the original author, i.e. me.
But it is useful to have them, so add them.
Also update the cec.h.rst.exceptions file to avoid errors when
building the documentation.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that proper V4L2 pixel formats exist for all 32-bit RGB
permutations, drop support for the poorly defined legacy format
V4L2_PIX_FMT_BGR32.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the uapi does not contain the num_ref_idx_active_override_flag,
drivers for decoders that do not parse slices themselves don't know
how to choose between the num_ref_idx_l[01]_default_active and the
num_ref_idx_l[01]_active override fields.
Instead, userspace must set the override fields to the default values
if the slice does not have the num_ref_idx_active_override flag set.
The drivers will then always enable the override internally and ignore
the default fields completely.
Clarify this requirement in the API documentation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document that the slice headers must be included for the benefit of
decoders that parse them (partially) in hardware, and that the start
code is optional. Add a link to the ITU-T Rec. H.264 specification
section that describes the slice format.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Step '8.2.4.1 Decoding process for picture numbers' was missing in the
reflist creation logic, leading to invalid P reflists when a
->frame_num wraparound happens.
Fixes: a9471e2562 ("media: hantro: Add core bits to support H264 decoding")
Reported-by: Francois Buergisser <fbuergisser@google.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Francois Buergisser <fbuergisser@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
And use it for all native type comparisons, even if it's not strictly
required. By doing that we make the code more consistent and prevent
from potential incorrect results in case of overflow or when the the
values being compared are both negative.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Francois Buergisser <fbuergisser@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
So it matches the code and the spec.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Francois Buergisser <fbuergisser@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The hardware is capable to passing V4L2_FIELD_ALTERNATE to user-space.
Allow users to request this field format but still default to using the
hardware interlacer if alternating is not explicitly requested.
Before this change a sensor providing data using alternate would be
always combined to an interlaced frame. After this change the user can
request to receive frames as alternate if the sensor provides it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The crop and compose rectangles are reset when s_fmt is called
resulting in potentially valid rectangles being lost when updating the
format. Fix this by mapping the rectangles inside the new format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable to hold the video source information dimensions was poorly
named 'source'. This is confusing as a lot of other members of structs
share the same name with different purposes, rename it src_rect in
preparation of refactoring code.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_FIELD_IS_INTERLACED() can be used to make the code more
readable, use it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While refactoring code the return statement became corrupted, fix it by
returning the correct return code.
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 897e371389 ("media: rcar-vin: simplify how formats are set and reset"
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Modify hantro_get_ref() and hantro_h264_get_ref_buf() helpers
to return the buffer DMA address, this makes the code simpler
and at the same time will allow easier enablement of the
post-processing feature.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It seems all codecs are using a 16x16 size macroblock,
and so it's possible to have just one set of macroblock macros.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, if start streaming -> stop streaming -> start streaming
sequence is executed, driver will end job prematurely, if ctx->translen
is higher than 1, because "aborting" flag is still set from previous
stop streaming command.
Fix that by clearing "aborting" flag in start streaming handler.
Fixes: 96d8eab5d0 ("V4L/DVB: [v5,2/2] v4l: Add a mem-to-mem videobuf framework test device")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vbi stream is started, followed by video streaming,
the vid_cap_streaming and vid_out_streaming were not being set to true,
which would cause the video stream to stop when vbi stream is stopped.
This patch allows to set vid_cap_streaming and vid_out_streaming to true.
According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)'
checks are a left-over from the original vivid development and should never
have been there.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
