Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic
rates have been properly set. To avoid problems with the firmware not
expecting to receive frames at rates that are not set during
CMD_START_ROLE, we now start with all basic rates by default.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When the data rates change, we get BSS_CHANGED_BASIC_RATES. At this
point, we should update all the templates to match the new rates. We
were changing some of the templates, but the beacon and the probe
response templates were missing.
[Remove redundant min_rate variable - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
There are some problems with MCS_13 in PG 1.0 hardware. So we disable
it when PG 1.0 is detected.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We can do get the HW information and identify the chip already at
probe time. This makes it easier to mangle with the parameters during
identify chip before registering the hardware with mac80211.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Like HDK, COM8 uses 0x06 for the low_band_component_type as well.
Hardcode the value for COM8 until this configuration can be done in
the external configuration binary (to be implemented).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
When allocating the fw_status structure, the space for the
lower-driver private area was missing. This was causing an illegal
write outside the allocated area, which was causing random oopses
around the kernel.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Since the most common board we're using now is an HDK board, change
the default board_type to hdk.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We were changing the low_band_component_type in the private
configuration structure before copying the default values to it, so
the change was overwritten and only took effect after HW recovery.
Reported-by: Dror Erez <drorer@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In some cases we may want to dump all the SDIO data in order to get
detailed information for debugging the communication with the
firmware.
Add printks to dump the data and a module parameter to enable/disable
it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
In wl18xx we don't have an NVS yet, so we need to control whether 11a
is supported with a module parameter for now. 11a support is enabled
by default and can be changed by setting enable_11a to false when
loading the module.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the get_mac operation in order to fetch the BD_ADDR from fuse ROM,
so that we can derive the WLAN MAC addresses from it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The number of RX packet descriptors may vary from chip to chip and
in different firmware versions. Unfortunately, the array that
contains the actual descriptors is in the middle of the fw_status
structure. To manage this, we split the struct into two so we can
calculate the offset of what comes after the array and access the last
elements more easily.
[Changed the STATUS_LEN macro to be placement agnostic - Arik]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We need to specify the number of 2.4GHz and 5GHz antennas and whether
the board has an internal or external DC2DC. Add some module
parameters that allow changing that.
In the future this will come from the "NVS" file.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Currently, all HDK boards use low_band_component_type 0x06. In the
future this may change, but for now, we hardcode this value when the
board_type is set to HDK.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the correct FW name for PLT (which is the same as the normal
firmware) and implement the plt_init operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
PLT mode needs to be initialized differently for each chip. This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add more board types and remove a now unneeded write to SCR_PAD2 setting
the board type.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In this chip family the NVS file should not be uploaded to FW. In fact,
we encounter strange bugs (sdio errors) when trying to upload it with
certain parameters.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This ensures the index is 0 on FW recovery and prevents spurious error
prints - "WARNING illegal id in tx completion".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only wl127x chips use the rx_mem_pool_addr values, which need to be
given to the firmware as part of the RX path. Move this from core to
the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Read the HW PG version of the 18xx chip from FUSE.
Based on an earlier patch by Luciano Coelho <coelho@ti.com>.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only wl12xx needs to get the ref_clock anc tcxo_clock values from the
platform data. Move these elements from the wl1271 structure to
wl12xx's private data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The wl12xx.h file now contains mostly definitions that are internal to
wlcore. Still, some things need to me moved to the public header, so
for now we keep including it in wlcore.h.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Instead of using hardcoded values for a single frequency, we need to
read the frequency and use the appropriate values for it in the top
initialization.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Define the FW pc in the 18xx register translation table. This specific
register is only valid in the boot partition, so change the momentarily
change partitions. This doesn't damage 12xx cards, where the FW pc is
accessible via boot partition as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware uses the SCR_PAD2 register to read the board type passed
from the driver. The values don't match the ones used in the mac and
phy configuration, so we need to map them before writing. This commit
adds a translation table that is used when writing the board type to
SCR_PAD2.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Different board types (ie. FPGA, HDK and DVP/EVB) require slightly
different init configuration options. Since we cannot probe the type
of board from the actual hardware, we need to pass it as an option
during module load.
This patch adds a module parameters that accepts the 3 different board
types, with DVP/EVB as the default, and uses this value where needed.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Set an alternate HT cap allowing MIMO rates (but only 20mhz) channels,
when the module is loaded with ht_mode=mimo.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Define the default HT capabilities of the 18xx chip family - these include
support for wide-channel.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add a HW op to add extra enabled rates for AP-mode data-rates. Since
the rates might depend on channel properties, reconfigure AP-mode rates
when these change.
Implement the HW op for the 18xx family, where MIMO or wide-chan rates
can be added.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Parse the peer ht_cap element containing MCS8-MCS15 rates and pass it
to the FW. Rates unsupported by the HW will be sanitized by mac80211
before reaching us.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Translate the NL80211 channel type to a FW-specific channel type and send
it to the FW as part of the role-start command. For wl12xx this has no
effect - this element is treated as padding.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Track the current 802.11 channel type, defaulting to a NO_HT channel.
Update the channel type element when changed by mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Now wlcore requires the lower drivers to set the correct
configuration. Move the existing private configuration to the proper
place and add all generic configuration parameters.
The important changes are in Tx interrupt pacing and Rx BA window size.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Some chip families can checksum certain classes of Rx packets in FW.
Implement the Rx-checksum feature as a HW-op. For the 18xx chip-family,
set Rx-checsum according to indication from FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some chip families are capable of checksumming certain classes of Tx
packets in HW. Indicate this fact in the netdev features and perform the
HW checksum by protocol type for the 18xx family.
Fix the location of the skb network header when we move it so we can
rely on it when setting the checksum.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement immediate Tx completion for the 18xx family. Move 18xx
specific Tx code to new tx.c/h files and create helper header files
for definitions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the 18xx-specific way for getting the length of a Rx packet.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the HW op for getting alignment state in wl18xx. The FW aligns
the Rx Ethernet payload data.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl18xx chip passes extra information in the firmware status to the
driver. Add a private data section to handle that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Define HW-rate conversion tables for the 18xx chip. Initialize
the appropriate wlcore elements with these tables and values to allow
conversion of HW-rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the frame length during Tx in a way compatible with the 18xx FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the 18xx variant to the HW Tx descriptor union and set the 18xx
specific values during Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the Tx spare block counts for all operating modes in the 18xx
card.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the number of Tx-descriptors for the 18xx family.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make use of the wlcore provided private storage in the 18xx low-level
driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the operations that allow wlcore to trigger commands to the
firmware and acknowledge when an event has been fully received.
Allocate a private buffer to hold the maximum sized cmd. Send the
entire length of the buffer each time a command is sent to signal
EOT. Remove the previous EOT mechanism.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the boot operation. Add a wl18xx-specific configuration
structure (namely to configure the mac and phy parameters).
The default hw configuration matches the DVP board.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add identify_chip operation to detect the chip ID for wl185x and set
the correct firmware name.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the register table with the appropriate values for wl18xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We don't have any chip-specific operations yet, but now wlcore has
defined an operations structure and requires the pointer to be set.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
At least in PG1, the wl18xx chips use the same SDIO vendor/device ID,
so it's not possible to figure out which driver is to be used. As a
workaround, we can check the SDIO revision number, because wl18xx uses
3.00 and wl12xx does not.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the wl18xx module and the probe functions. Use wlcore for the
main parts (not functional at this point due to differences in the
wl18xx initialization).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we terminate the eeprom access through clearing the CS by:
RTL_W8 (Cfg9346, ~EE_CS); or writeb (~EE_CS, ee_addr);
This would left the eeprom into "Config. Register Write Enable:"
state which is not expcted as the highest two bits were set to
0x11 ( expected is the "Normal" mode (0x00)). Solving this by write
0x0 instead of ~EE_CS when terminating the eeprom access.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we enable the receiver before setting the ring address which could
lead the card DMA into unexpected areas. Solving this by set the ring address
before enabling the receiver.
btw. I find and test this in qemu as I didn't have a 8139cp card in hand. please
review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "!mlx4_is_slave" is totally confusing. Fix with
constant MLX4_CMD_NATIVE, which is the intended behavior.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range check was performed after using the port number.
Reverse this to prevent a potential array overflow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- pass the following parameters:
- firmware version (added QUERY_FW paravirtualization for that)
- disable Blueflame on slaves. KVM disables write combining on guests,
and we get better performance without BF in this case. (This requires
QUERY_DEV_CAP paravirtualization, also in this commit)
- max qp rdma as destination
- get rid of a chunk of "if (0)" dead code
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port is used as an array index before we know if that is proper.
For example, in the catas event case, port is zero; however,
the port index should lie in the range (1..2).
Fix this by using 'port' only in the events where it is of interest.
Test for port out of range in the default (unhandled event) case,
and do not output a message if it is not an ethernet port.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV mode, the number of EQs used when computing the total ICM size
was incorrect.
To fix this, we do the following:
1. We add a new structure to mlx4_dev, mlx4_phys_caps, to contain physical HCA
capabilities. The PPF uses the phys capabilities when it computes things
like ICM size.
The dev_caps structure will then contain the paravirtualized values, making
bookkeeping much easier in SRIOV mode. We add a structure rather than a
single parameter because there will be other fields in the phys_caps.
The first field we add to the mlx4_phys_caps structure is num_phys_eqs.
2. In INIT_HCA, when running in SRIOV mode, the "log_num_eqs" parameter
passed to the FW is the number of EQs per VF/PF; each function (PF or VF)
has this number of EQs available.
However, the total number of EQs which must be allowed for in the ICM is
(1 << log_num_eqs) * (#VFs + #PFs). Rather than compute this quantity,
we allocate ICM space for 1024 EQs (which is the device maximum
number of EQs, and which is the value we place in the mlx4_phys_caps structure).
For INIT_HCA, however, we use the per-function number of EQs as described
above.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ths fixes the comparison in the FLR (Function Level Reset) event case.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David S. Miller:
1) Fix IPSEC header length calculation for transport mode in ESP. The
issue is whether to do the calculation before or after alignment.
Fix from Benjamin Poirier.
2) Fix regression in IPV6 IPSEC fragment length calculations, from Gao
Feng. This is another transport vs tunnel mode issue.
3) Handle AF_UNSPEC connect()s properly in L2TP to avoid OOPSes. Fix
from James Chapman.
4) Fix USB ASIX driver's reception of full sized VLAN packets, from
Eric Dumazet.
5) Allow drop monitor (and, more generically, all generic netlink
protocols) to be automatically loaded as a module. From Neil
Horman.
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
due to new entries added next to each other at the end. As usual.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net/smsc911x: Repair broken failure paths
virtio-net: remove useless disable on freeze
netdevice: Update netif_dbg for CONFIG_DYNAMIC_DEBUG
drop_monitor: Add module alias to enable automatic module loading
genetlink: Build a generic netlink family module alias
net: add MODULE_ALIAS_NET_PF_PROTO_NAME
r6040: Do a Proper deinit at errorpath and also when driver unloads (calling r6040_remove_one)
r6040: disable pci device if the subsequent calls (after pci_enable_device) fails
skb: avoid unnecessary reallocations in __skb_cow
net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens
asix: allow full size 8021Q frames to be received
rds_rdma: don't assume infiniband device is PCI
l2tp: fix oops in L2TP IP sockets for connect() AF_UNSPEC case
mac80211: fix ADDBA declined after suspend with wowlan
wlcore: fix undefined symbols when CONFIG_PM is not defined
mac80211: fix flag check for QoS NOACK frames
ath9k_hw: apply internal regulator settings on AR933x
ath9k_hw: update AR933x initvals to fix issues with high power devices
ath9k: fix a use-after-free-bug when ath_tx_setup_buffer() fails
ath9k: stop rx dma before stopping tx
...
Current failure paths attempt to free resources which we failed to request
and disable resources which we failed to enable ones. This leads to kernel
oops/panic. This patch does some simple re-ordering to prevent this from
happening.
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable_cb is just an optimization: it
can not guarantee that there are no callbacks.
In particular it doesn't have any effect when
event index is on.
Instead, detach, napi disable and reset on freeze ensure we don't run
concurrently with a callback.
Remove the useless calls so we get same behaviour
with and without event index.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so if mdiobus_alloc fails, the errorpath doesnt do a netif_napi_del and also
doesn't set the priv data of the driver to NULL.
at the driver unload stage the driver doesn't remove the NAPI context, and
doesnt' set the priv data to NULL, and also doesn't call the pci_iounmap.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the calls after the pci_enable_device may fail, and will error out with out
disabling it. disable the device at error paths.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Receive Descriptor Empty happens, rxdesc pointer of the driver
and actual next descriptor of the controller may be mismatch.
This patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
asix driver drops 8021Q full size frames because it doesn't take into
account VLAN header size.
Tested on AX88772 adapter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Allan Chou <allan@asix.com.tw>
CC: Trond Wuellner <trond@chromium.org>
CC: Grant Grundler <grundler@chromium.org>
CC: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c21eebb503
"wl12xx: add RX filters ACX commands" breaks the build
when CONFIG_PM isn't defined:
ERROR: "wl1271_rx_filter_get_fields_size"
[drivers/net/wireless/ti/wlcore/wlcore.ko] undefined!
ERROR: "wl1271_rx_filter_flatten_fields"
[drivers/net/wireless/ti/wlcore/wlcore.ko] undefined!
code in drivers/net/wireless/ti/wlcore/acx.c is using these
functions unconditionally while they are #ifdefed CONFIG_PM.
Fix it by ifdefing all relevant RX filters code with CONFIG_PM.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR933x, the internal regulator settings need to be applied before the
PLL init to avoid stability issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"> Can you provide more information about the issues with high power devices?
Tx being flakey and Rx not working at all."
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_setup_buffer() can fail if there is no ath_buf left, or if mapping DMA
failed. In this case it frees the skb passed to it.
If ath_tx_setup_buffer is called from ath_tx_form_aggr, the skb is still
linked into the tid buffer list and must be dequeued before being released.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been found that active Rx can interfere with stopping tx DMA, which
could result in at least parts of those "Failed to stop Tx DMA!" messages.
Stopping rx before tx should prevent that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
More cleanups, continuing an earlier set with omap and samsung specific
cleanups. These could not go into the first set because they have
dependencies on various other series that in turn depend on the first
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7UKB
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
iEYEABECAAYFAk+/R7EACgkQ31LbvUHyf1dp9QCfX9xPFDERRWwvyDAAl9zLONxj
K+kAnRNydbw7UglqIYUnreCfNemfMdmg
=w9Td
-----END PGP SIGNATURE-----
Merge tag 'cris-for-linus' of git://jni.nu/cris
Pull CRIS changes from Jesper Nilsson:
"No major changes here, but fixes some compile errors for CRIS, some
small style issues, some documentation and as a bonus nukes a couple
of obsolete rtc-files and related code."
* tag 'cris-for-linus' of git://jni.nu/cris:
cris: Remove old legacy "-traditional" flag from arch-v10/lib/Makefile
CRIS: Remove legacy RTC drivers
cris/mm/fault.c: Port OOM changes to do_page_fault
cris:fix the wrong function declear
CRIS: Add _sdata to vmlinux.lds.S
cris: posix_types.h, include asm-generic/posix_types.h
CRIS: Update documentation
cris/arch-v32: cryptocop: Use kzalloc
net:removed the unused variable
cris:removed the unused variable
CRISv32: Correct name of read_mostly section.
The firmware is more than 300KB big and you should not use kmalloc for
such big allocations. This allocation with kmalloc failed on my mips
based device (BCM47186).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If drv->op_mode is NULL after trying to init the
opmode, we go to the wrong label. Fix this, and
clean up the code a bit.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a station fails in
iwl_restore_stations, the driver treats it
like a successful station add and sends a
link quality command, when it it shouldn't.
This patch fixes one of the potential
sources for kernel warnings like this one:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-sta.c:905 iwl_send_lq_cmd+0x130/0x217 [iwlwifi]()
Hardware name: 3323A2G
Modules linked in: ...
Pid: 17359, comm: kworker/u:2 Tainted: G O 3.3.0-wl+ #1
Call Trace:
[<ffffffff81039620>] warn_slowpath_common+0x7e/0x96
[<ffffffff8103964d>] warn_slowpath_null+0x15/0x17
[<ffffffffa02a9f0b>] iwl_send_lq_cmd+0x130/0x217 [iwlwifi]
[<ffffffffa02aa1fb>] iwl_restore_stations+0x209/0x289 [iwlwifi]
[<ffffffffa02b07c2>] iwlagn_commit_rxon+0x602/0x7bd [iwlwifi]
[<ffffffffa02b111f>] iwlagn_bss_info_changed+0x247/0x31a [iwlwifi]
[<ffffffffa0861437>] ieee80211_bss_info_change_notify+0x1a5/0x1ba [mac80211]
[<ffffffffa088afad>] ieee80211_destroy_auth_data+0x4b/0x70 [mac80211]
[<ffffffffa088df26>] ieee80211_sta_work+0xb5/0x954 [mac80211]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode16 option is still very much work in
progress, so there's no need to ask any users
about it. Remove the option and code for now,
we'll put it back when it's actually working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shadow registers in the device are meant to
allow the driver to update certain device
registers without needing to wake up all
components of the device. However, using
this feature in the device causes
communication between the driver and the
device to become unreliable, resulting in
host command timeouts.
Disable this feature by default till a fix is
available for the bug.
Cc: stable@vger.kernel.org #2.6.38+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic that allows to have a short TFD queue was completely wrong.
We do maintain 256 Transmit Frame Descriptors, but they point to
recycled buffers. We used to attach and de-attach different TFDs for
the same buffer and it worked since they pointed to the same buffer.
Also zero the number of BDs after unmapping a TFD. This seems not
necessary since we don't reclaim the same TFD twice, but I like
housekeeping.
This patch solves this warning:
[ 6427.079855] WARNING: at lib/dma-debug.c:866 check_unmap+0x727/0x7a0()
[ 6427.079859] Hardware name: Latitude E6410
[ 6427.079865] iwlwifi 0000:02:00.0: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x00000000296d393c] [size=8 bytes]
[ 6427.079870] Modules linked in: ...
[ 6427.079950] Pid: 6613, comm: ifconfig Tainted: G O 3.3.3 #5
[ 6427.079954] Call Trace:
[ 6427.079963] [<c10337a2>] warn_slowpath_common+0x72/0xa0
[ 6427.079982] [<c1033873>] warn_slowpath_fmt+0x33/0x40
[ 6427.079988] [<c12dcb77>] check_unmap+0x727/0x7a0
[ 6427.079995] [<c12dcdaa>] debug_dma_unmap_page+0x5a/0x80
[ 6427.080024] [<fe2312ac>] iwlagn_unmap_tfd+0x12c/0x180 [iwlwifi]
[ 6427.080048] [<fe231349>] iwlagn_txq_free_tfd+0x49/0xb0 [iwlwifi]
[ 6427.080071] [<fe228e37>] iwl_tx_queue_unmap+0x67/0x90 [iwlwifi]
[ 6427.080095] [<fe22d221>] iwl_trans_pcie_stop_device+0x341/0x7b0 [iwlwifi]
[ 6427.080113] [<fe204b0e>] iwl_down+0x17e/0x260 [iwlwifi]
[ 6427.080132] [<fe20efec>] iwlagn_mac_stop+0x6c/0xf0 [iwlwifi]
[ 6427.080168] [<fd8480ce>] ieee80211_stop_device+0x5e/0x190 [mac80211]
[ 6427.080198] [<fd833208>] ieee80211_do_stop+0x288/0x620 [mac80211]
[ 6427.080243] [<fd8335b7>] ieee80211_stop+0x17/0x20 [mac80211]
[ 6427.080250] [<c148dac1>] __dev_close_many+0x81/0xd0
[ 6427.080270] [<c148db3d>] __dev_close+0x2d/0x50
[ 6427.080276] [<c148d152>] __dev_change_flags+0x82/0x150
[ 6427.080282] [<c148e3e3>] dev_change_flags+0x23/0x60
[ 6427.080289] [<c14f6320>] devinet_ioctl+0x6a0/0x770
[ 6427.080296] [<c14f8705>] inet_ioctl+0x95/0xb0
[ 6427.080304] [<c147a0f0>] sock_ioctl+0x70/0x270
Cc: stable@vger.kernel.org
Reported-by: Antonio Quartulli <ordex@autistici.org>
Tested-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.
Cc: stable@vger.kernel.org #2.6.38+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calculating the number of slots required for a packet header, the code
was reserving too many slots if the header crossed a page boundary. Since
netbk_gop_skb copies the header to the start of the page, the count of
slots required for the header should be based solely on the header size.
This problem is easy to reproduce if a VIF is bridged to a USB 3G modem
device as the skb->data value always starts near the end of the first page.
Signed-off-by: Simon Graham <simon.graham@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some additional Gobi3K IDs found in the BSD/GPL licensed
out-of-tree GobiNet driver from Sierra Wireless.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
Here is the big staging tree pull request for the 3.5-rc1 merge window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out of
the staging tree, to their respective "real" portions of the kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q8MACgkQMUfUDdst+ymjogCguo8fANFVlPWeZGeoBTL+aQfQ
yTkAoLE0codmh+2SvhulYgyU1Wh6ZDK2
=nJ2F
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree changes from Greg Kroah-Hartman:
"Here is the big staging tree pull request for the 3.5-rc1 merge
window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out
of the staging tree, to their respective "real" portions of the
kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up various trivial conflicts, along with a non-trivial one found
in -next and pointed out by Olof Johanssen: a clean - but incorrect -
merge of the arch/arm/boot/dts/at91sam9g20.dtsi file. Fix up manually
as per Stephen Rothwell.
* tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (536 commits)
Staging: bcm: Remove two unused variables from Adapter.h
Staging: bcm: Removes the volatile type definition from Adapter.h
Staging: bcm: Rename all "INT" to "int" in Adapter.h
Staging: bcm: Fix warning: __packed vs. __attribute__((packed)) in Adapter.h
Staging: bcm: Correctly format all comments in Adapter.h
Staging: bcm: Fix all whitespace issues in Adapter.h
Staging: bcm: Properly format braces in Adapter.h
Staging: ipack/bridges/tpci200: remove unneeded casts
Staging: ipack/bridges/tpci200: remove TPCI200_SHORTNAME constant
Staging: ipack: remove board_name and bus_name fields from struct ipack_device
Staging: ipack: improve the register of a bus and a device in the bus.
staging: comedi: cleanup all the comedi_driver 'detach' functions
staging: comedi: remove all 'default N' in Kconfig
staging: line6/config.h: Delete unused header
staging: gdm72xx depends on NET
staging: gdm72xx: Set up parent link in sysfs for gdm72xx devices
staging: drm/omap: initial dmabuf/prime import support
staging: drm/omap: dmabuf/prime mmap support
pstore/ram: Add ECC support
pstore/ram: Switch to persistent_ram routines
...
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as well.
We deleted a staging driver, which was nice, and finally dropped the
obsolete usbfs code, which will make Al happy to never have to touch
that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were due
to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7qs0ACgkQMUfUDdst+ymjOgCfeoWqWk1bsKKt6SZULvQois5i
3csAn1Uapcm8Uswwpnj2v1/2Zh4rBHLA
=4jM1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
Netfront driver can be also useful in dom0, eg when all NICs are assigned to
some domU (aka driver domain). Then using netback in domU and netfront in dom0
is the only way to get network access in dom0.
Signed-off-by: Marek Marczykowski <marmarek@invisiblethingslab.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John says:
--------------------
I apologize for not having sent this sooner. FWIW, I was in a car
somewhere between Illinois and North Carolina for most of the day
Sunday and Monday... :-)
This is (obviously) the last non-fix pull request for wireless bits
intended for 3.5. It includes AP support for mwifiex, a variety of HCI
and other updates for NFC, some brcmfmac and brcmsmac refactoring,
a large batch of ssb and bcma updates, a batch of ath6kl updates,
some cfg80211 and mac80211 updates/refactoring from Johannes Berg,
a rather large collection of Bluetooth updates by way of Gustavo,
and a variety of other bits here and there.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
FCB(Frame Control Block) isn't the part of netdev hard header.
Add FCB to hard_header_len will make GRO fail at MAC comparision stage.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yWfr
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.
* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
IB/mlx4: Fix mlx4_ib_add() error flow
IB/core: Fix IB_SA_COMP_MASK macro
IB/iser: Fix error flow in iser ep connection establishment
IB/mlx4: Increase the number of vectors (EQs) available for ULPs
RDMA/cxgb4: Add query_qp support
RDMA/cxgb4: Remove kfifo usage
RDMA/cxgb4: Use vmalloc() for debugfs QP dump
RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
RDMA/cxgb4: Add DB Overflow Avoidance
RDMA/cxgb4: Add debugfs RDMA memory stats
cxgb4: DB Drop Recovery for RDMA and LLD queues
cxgb4: Common platform specific changes for DB Drop Recovery
cxgb4: Detect DB FULL events and notify RDMA ULD
RDMA/cxgb4: Drop peer_abort when no endpoint found
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
mlx4_core: Change bitmap allocator to work in round-robin fashion
RDMA/nes: Don't call event handler if pointer is NULL
RDMA/nes: Fix for the ORD value of the connecting peer
...
Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Setup CROSS_COMPILE at the top
m68k: Correct the Atari ALLOWINT definition
m68k/video: Create <asm/vga.h>
m68k: Make sure {read,write}s[bwl]() are always defined
m68k/mm: Port OOM changes to do_page_fault()
scsi/atari: Make more functions static
scsi/atari: Revive "atascsi=" setup option
net/ariadne: Improve debug prints
m68k/atari: Change VME irq numbers from unsigned long to unsigned int
m68k/amiga: Use arch_initcall() for registering platform devices
m68k/amiga: Add error checks when registering platform devices
m68k/amiga: Mark z_dev_present() __init
m68k: Remove unused MAX_NOINT_IPL definition
Use single_release() instead of seq_release() to free memory allocated
by single_open().
Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ZTE (Vodafone) K3765-Z to the whitelist. This requires the
previous patch to make the whitelist with forced interface 4 generic
or the device fails to initialise. After applying this patch and
loading the Option driver without usb-modeswitch's bind all
interfaces trick, a wwan0 net interface and /dev/cdc-wdm0 device
file were created. Using Bjorn Mork's perl connection script a
connection was made to a mobile network using QMI and the network
interface's IPv4 address was configured OK.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the forced interface 4 whitelist to use the generic shared
binder instead of the Gobi specific one. Certain ZTE devices
(K3520-Z & K3765-Z) don't work with the Gobi version, but function
quite happily with the generic. This has been tested with the following
devices:
K3520-Z
K3565-Z
K3765-Z
K4505-Z
It hasn't been tested with the ZTE MF820D, which is the only other
device that uses this whitelist at present. Although Bjorn doesn't
expect any problems, any testing with that device would be appreciated.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ZTE WWAN devices have generic CDC Ether descriptors. Add those
into the whitelist so that we get FLAG_WWAN on the interface
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update our reference driver to use netdev_alloc_frag() API instead of
the temporary custom allocator I introduced in commit 8d4057a938
(tg3: provide frags as skb head)
This removes the memory leak we had, since we could leak one page at
device dismantle.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call consume_skb() in place of kfree_skb() were appropriate.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move blocks of code around to avoid function prototypes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce and use a debug macro to test and print.
Convert printks to pr_<level>.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just some stylings.
Use #include <linux... not #include <asm...
Convert a test and print to a printk_once.
Combine an "if (foo) { if (bar) {" to single "if (foo && bar) {"
to save an indent level.
Convert single line "if (foo) bar;" to multiple lines.
Move some braces.
Align some long lines a bit better.
Long lines and printks with KERN_ checkpatch complaints
still exist.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neaten the comments and reflow the code without
changing anything other than whitespace.
git diff -w shows just comment neatening and a few
line removals.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
recover LLD EQs for DB drop interrupts. This includes adding a new
db_lock, a spin lock disabling BH too, used by the recovery thread and
the ring_tx_db() paths to allow db drop recovery.
Clean up initial DB avoidance code.
Add read_eq_indices() - this allows the LLD to use the PCIe mw to
efficiently read hw eq contexts.
Add cxgb4_sync_txq_pidx() - called by iw_cxgb4 to sync up the sw/hw
pidx value.
Add flush_eq_cache() and cxgb4_flush_eq_cache(). This allows iw_cxgb4
to flush the sge eq context cache before beginning db drop recovery.
Add module parameter, dbfoifo_int_thresh, to allow tuning the db
interrupt threshold value.
Add dbfifo_int_thresh to cxgb4_lld_info so iw_cxgb4 knows the threshold.
Add module parameter, dbfoifo_drain_delay, to allow tuning the amount
of time delay between DB FULL and EMPTY upcalls to iw_cxgb4.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add platform-specific callback functions for interrupts. This is
needed to do a single read-clear of the CAUSE register and then call
out to platform specific functions for DB threshold interrupts and DB
drop interrupts.
Add t4_mem_win_read_len() - mem-window reads for arbitrary lengths.
This is used to read the CIDX/PIDX values from EC contexts during DB
drop recovery.
Add t4_fwaddrspace_write() - sends addrspace write cmds to the fw.
Needed to flush the sge eq context cache.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Patch re-spin.
Incorporated review comments by Ben Hutchings.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As iwlwifi use fat skbs, it should not pull too much data in skb->head,
and particularly no tcp data payload, or splice() is slower, and TCP
coalescing is disabled. Copying payload to userland also involves at
least two copies (part from header, part from fragment)
Each layer will pull its header from the fragment as needed.
(on 64bit arches, skb_tailroom(skb) at this point is 192 bytes)
With this patch applied, I have a major reduction of collapsed/pruned
TCP packets, a nice increase of TCPRcvCoalesce counter, and overall
better Internet User experience.
Small packets are still using a fragless skb, so that page can be reused
by the driver.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of the inw/outw functions by the cs89x0 platform driver
results in NULL pointer references on ARM platforms and
platforms that do not provide ISA-style programmed I/O accessors.
Using inw/outw also accesses the wrong address space on platforms
that have a PCI I/O space that is not identity-mapped into the
physical address space.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Killing reset task while adapter is resetting causes deadlock.
Only kill reset task if adapter is not resetting.
Ref bug #43132 on bugzilla.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.
This commit removes any MCA specific net drivers, and removes
any MCA specific probe/support code from drivers that were
doing a dual ISA/MCA role.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change the TX ring scheme such that the number of rings for untagged packets
and for tagged packets (per each of the vlan priorities) is the same, unlike
the current situation where for tagged traffic there's one ring per priority
and for untagged rings as the number of core.
Queue selection is done as follows:
If the mqprio qdisc is operates on the interface, such that the core networking
code invoked the device setup_tc ndo callback, a mapping of skb->priority =>
queue set is forced - for both, tagged and untagged traffic.
Else, the egress map skb->priority => User priority is used for tagged traffic, and
all untagged traffic is sent through tx rings of UP 0.
The patch follows the convergence of discussing that issue with John Fastabend
over this thread http://comments.gmane.org/gmane.linux.network/229877
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Liran Liss <liranl@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch removes unused return value from __delete_item() and
delete_item() methods in drivers/net/ppp/pppoe.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That old mail address doesnt exist any more.
This changes all occurences to my new address.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Under certain scenarios, it's possible that bursty manageability traffic
over the BMC-to-OS path may overrun the internal manageability receive
buffer causing dropped manageability packets. Clearing this bit prevents
this situation by interrupting coalescing to allow manageability traffic
through.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code seems to want to look at the last byte where the HW puts some
information. Since the skb->data area is never seen by the HW I guess it
does not work as expected. We pass the page address to the HW so I
*think* in order to get to the last byte where the information might be
one should use the page buffer and take a look.
This is of course not more than just compile tested.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the comment, errata 23 says that the memory we allocate
can't cross a 64KiB boundary. In case of jumbo frames we allocate
complete pages which can never cross the 64KiB boundary because
PAGE_SIZE should be a multiple of 64KiB so we stop either before the
boundary or start after it but never cross it. Furthermore the check
seems bogus because it looks at skb->data which is not seen by the HW
at all because we only pass the DMA address of the page we allocated. So
I *think* the workaround is not required here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This define is needed by i217.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
__napi_schedule might raise softirq but nothing
causes do_softirq to trigger, so it does not in fact
run. As a result,
the error message "NOHZ: local_softirq_pending 08"
sometimes occurs during boot of a KVM guest when the network service is
started and we are oom:
...
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0...NOHZ: local_softirq_pending 08
done.
[ OK ]
...
Further, receive queue processing might get delayed
indefinitely until some interrupt triggers:
virtio_net expected napi to be run immediately.
One way to cause do_softirq to be executed is by
invoking local_bh_enable(). As __napi_schedule is
normally called from bh or irq context, this
seems to make sense: disable bh before __napi_schedule
and enable afterwards.
In fact it's a very complicated way of calling do_softirq(),
and works since this function is only used when we are not
in interrupt context. It's not hot at all, in any ideal scenario.
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Tested-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
