* This patch fixes a bug in calculating the scaled
power for three chain chipsets.
* Also, a delay is needed after setting DAC low-power mode in
TOP1 RF register (Top Level Register Bits).
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Do an AHB reset before doing RTC reset"
fixed RTC reset issue for AR9280 2.0 chipsets and above.
The fix is valid for all AR9280 chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to account for the number of chains in use,
not just the number of chains present.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 requires a full reset during channel change and HW reset.
Currently, a fast channel change is done. This patch fixes
this bug.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NF value may be incorrect when we read it just after the chip
has gone through a full sleep mode. Reading incorrect NF values
affects RX throughput.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting bit 20 and 25 of 0x8344 can cause occasional rx data
corruption, clear them to fix this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Waking up the chip after powering it down fails sometimes.
In this case the CPU is locked for 200ms. Reduce this
interval to 10ms to avoid excessive busy looping.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For chips requiring RTC reset, TSF has to be restored
after power on reset.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Disable L1 state ONLY when device is in D3 mode.
* Clear bit 22 of register 0x4004.
* Handle power on/off properly
Not setting the workarounds properly resulted in the
disappearance of the card in certain cases.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default noise floor was never initialized for
AR9287.This patch helps in reporting the correct
RSSI for this version of chipset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LP (and probably N) PHY has the same radio disabled bit as
the higher-revision A and G PHYs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO works (more or less), so remove the BROKEN dependency and
let people test it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following build error when CONFIG_B43_LEDS is not selected:
drivers/net/wireless/b43/main.c: In function 'b43_remove':
drivers/net/wireless/b43/main.c:4990: error: 'struct b43_leds' has no member named 'stop'
drivers/net/wireless/b43/main.c:4991: error: 'struct b43_leds' has no member named 'work'
make[4]: *** [drivers/net/wireless/b43/main.o] Error 1
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't abuse wl->current_dev in the LED work for checking whether we're
going down. Add an explicit variable.
This fixes a crash on rmmod dereferencing the wl->current_dev NULL pointer
in various other places of the driver.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current verison of b43 uses "b43_phyop_switch_analog_generic" for A,
G and LP phys.
According to the spec, this is the wrong behaviour for the LP PHY
(see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore )
While no problems on the x86 plattform where seen, this leads to a crash
on the BCM5354 SoC (MIPS 32 LE plattform).
This patch implements the analog switch for LP PHYs according to the
specs. It fixes the crash
signed-off-by: Thomas Ilnseher <illth@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduces IRQ pressure by about one third on a saturated link
by disabling the PMQ mechanism. We currently don't use that mechanism.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for verbose runtime statistics.
It defaults to off and must be enabled in debugfs, if desired.
The first measurement may be incorrect, because statistics are not cleared
after they got enabled through debugfs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
synchronize_irq is meaningless for SDIO. sdio_release_irq will
sync the IRQ thread for us.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to release the SDIO host before locking the driver mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for Soft-MAC SDIO devices to b43.
The driver still lacks some fixes for SDIO devices, so it's currently
marked as BROKEN.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes most of the b43 suspend/resume code (it's handled by mac80211)
and moves the registration of devices to the attachment phase. This is
required, because we must not register/unregister devices on suspend/resume.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix printk format warnings:
drivers/ssb/sdio.c:336: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
drivers/ssb/sdio.c:443: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new usbid for Zcomax XG-705A to the device table.
Cc: stable@kernel.org
Reported-by: Jari Jaakola <jari.jaakola@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an SPROM revision is not recognized, the code falls back to a V1
SPROM; however, that revision is not forced in the appropriate structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.
Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can not assume antenna "A" is the first valid anttena for
all the NIC. Need to make sure choice the correct antenna based on
h/w configuration for transmit to avoid sending frame on invalid
antenna
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX handling maintains a few lists that keep track of the RX buffers.
Buffers move from one list to the other as they are used, replenished, and
again made available for usage. In one such instance, when a buffer is used
it enters the "rx_used" list. When buffers are replenished an skb is
attached to the buffer and it is moved to the "rx_free" list. The problem
here is that the buffer is first removed from the "rx_used" list _before_ the
skb is allocated. Thus, if the skb allocation fails this buffer remains
removed from the "rx_used" list and is thus lost for future usage.
Fix this by first allocating the skb before trying to attach it to a list.
We add an additional check to not do this unnecessarily.
Reported-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we cleaned up the driver to properly tell mac80211 about HT rates
("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke
internal rate indexing in 2.4 GHz band.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Tested-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a resume failure where a signal is pending on resume
so the firmware upload fails.
This removes the interruptible sleep, because we don't really need it.
In the worst case (with broken firmware) the sleep loop will take 1 second.
In the common case (working firmware), it will only take a few milliseconds.
So we don't really need to be interruptible.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this was added no defaults were set and it seems
this implies n. Default this to y.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force wake the mac80211 queues on init.
Under rare circumstances they may be stopped, if a DMA error or
something else causes a device reset while a queue was stopped.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbcd2).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.
Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: Martin Decky <martin@decky.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes `s3c_fb_remove' referenced in section `.data' of
drivers/built-in.o: defined in discarded section `.devexit.text' of
drivers/built-in.o
With CONFIG_HOTPLUG=n, functions marked with __devexit gets removed,
so make sure we use __devexit_p when referencing pointers to them.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/tmiofb.c: In function 'tmiofb_resume':
drivers/video/tmiofb.c:977: warning: 'retval' may be used uninitialized in this function
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fbcon makes the (reasonable) assumption that it only needs to program the
hardware once, when fbcon_init() is called for the foreground console.
This doesn't always play well with vgacon because vgacon_deinit() is only
doing its job when the last console it owns is closed (when switching from
vgacon to fbcon, that's usually *after* fbcon_init() has set the new
mode).
Depending on the hardware this can cause the wrong framebuffer location to
be scanned out (e.g. reproduced on nv05 with the nouveau framebuffer
driver).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Attempting to unload a framebuffer module calls unregister_framebuffer()
which in turn gets fbcon to release it. If fbcon has no framebuffers
linked to a console, it will also unbind itself from the console driver.
However, if fbcon never registered itself as a console driver, the unbind
will fail causing the framebuffer device entry to persist. In most cases
this failure will result in an oops when attempting to access the now
non-existent device.
This patch ensures that the fbcon unbind request will succeed even if a
bind was never done. It tracks if a successful bind ever occurred & will
only attempt to unbind if needed. If there never was a bind, it simply
returns with no error.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_FB_MATROX_32MB is always enabled, so there is no point in having
ifdefs all around. And it is bad practice to use CONFIG_* as a name for
something which is not a Kconfig option.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With multihead support always enabled, macros MINFO_FROM and
MINFO_FROM_INFO are no longer needed and make the code harder to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With multihead support always enabled, these macros are no longer needed
and make the code harder to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With multihead support always enabled, these macros are no longer needed
and make the code harder to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I would like to get rid of option CONFIG_FB_MATROX_MULTIHEAD and just
always enable it. There are many reasons for doing this:
* CONFIG_FB_MATROX_MULTIHEAD=y is what all x86 distributions do, so it
definitely works or we would know by now.
* Building the matroxfb driver with CONFIG_FB_MATROX_MULTIHEAD not set
results in the following build warning:
drivers/video/matrox/matroxfb_crtc2.c: In function 'matroxfb_dh_open':
drivers/video/matrox/matroxfb_crtc2.c:265: warning: the address of 'matroxfb_global_mxinfo' will always evaluate as 'true'
drivers/video/matrox/matroxfb_crtc2.c: In function 'matroxfb_dh_release':
drivers/video/matrox/matroxfb_crtc2.c:285: warning: the address of 'matroxfb_global_mxinfo' will always evaluate as 'true'
This is nothing to be worried about, the driver will work fine, but build
warnings are still annoying.
* The trick to get multihead support without CONFIG_FB_MATROX_MULTIHEAD,
which is described in the config help text, no longer works: you can't
load the same kernel module more than once.
* I fail to see how CONFIG_FB_MATROX_MULTIHEAD=y would make the code
significantly slower, contrary to what the help text says. A few extra
parameters on the stack here and there can't really slow things down in
comaprison to the rest of the code, and register access.
* The driver built without CONFIG_FB_MATROX_MULTIHEAD is larger than the
driver build with CONFIG_FB_MATROX_MULTIHEAD=y by 8%.
* One less configuration option makes things simpler. We add options
all the time, being able to remove one for once is nice. It improves
testing coverage. And I don't think the Matrox adapters are still
popular enough to warrant overdetailed configuration settings.
* We should be able to unobfuscate the driver code quite a bit after
this change (patches follow.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the moment about half of the framebuffer drivers can return an error
code in fb_set_par. Until now it would be silently ignored by fbmem.c
and fbcon.c. This patch fixes fbmem.c to return the error code and
restore var on error.
But it is not clear in which video mode the device is when fb_set_par
fails. It would be good and reasonable if it were in the old state but
there is no guarantee that this is true for all existing drivers.
Additionally print a message if a failing fb_set_par is detected in
fbmem.c or fbcon.c.
Although most errors should be caught by the previous fb_check_var some
errors can't as they are dynamic (memory allocations, ...) and can only be
detected while performing the operations which is forbidden in
fb_check_var.
This patch shouldn't have a negative impact on normal operation as all
drivers return 0 on success. The impact in case of error depends heavily
on the driver and caller but it's expected to be better than before.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the final part of the calculation for the tft display clockrate we
divide the output pf s3c2410fb_calc_pixclk() by 2 which leaves us with a
rounding error if the result is odd.
Change to using DIV_ROUND_UP() to ensure that we always choose a higher
divisor and thus a lower frequency.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use DIV_ROUND_UP explicitly instead of manual shifts and adds. It makes
the code more readable and consistent (sometimes there were shifts,
sometimes divs).
There is no change on the assembly level (compilers should do the right
job).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the range check for panning. The current code fails to detect some
invalid values (very high ones that can occur if an app tries to move
further up/left than 0,0) as the check uses the unknown values for
calculation so that an overflow can occur.
To fix this it is sufficient to move the calculation to the right side to
use only trusted values.
Kai Jiang detected this problem and proposed an initial patch.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Kai Jiang <b18973@freescale.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check that the result of kmalloc is not NULL before passing it to other
functions.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
[akpm@linux-foundation.org: convert to kstrdup() as well]
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It reads linetable[] before checking bounds of index, and ARRAY_SIZE is
required because linetable[] are unsigned shorts.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable 2D hardware acceleration on VX855 for copyarea, imageblit and
fillrect by selecting the correct engine which is the same as in VX800.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for a new VIA integrated graphics chipset, the VX855.
Signed-off-by: HaraldWelte <HaraldWelte@viatech.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
viafb: use read-only mode parsing
The previous method of mode parsing wrote to the strings resulting in
truncated mode strings in the sysfs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove a structure member 'on_slot' in the chip_info structure which is
completely unused.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main motivation of this patch was to merge the three initialization
functions in one and clean it up. However as some changes in other code
areas where needed to do it right some small other changes were made.
Changes to viafb_par:
io_virt renamed as engine_mmio and moved to shared
VQ_start renamed as vq_vram_addr and moved to shared
VQ_end removed as it is easily recalculatable
vq_vram_addr is not strictly needed but keep it to track where we
allocated video memory. The memory allocated for the virtual queue was
shrunk to VQ_SIZE as VQ_SIZE+CURSOR_SIZE looked like a bug to me. But to
be honest I don't have the faintest idea what virtual queues are for in
the graphic hardware and whether the driver needs them in any way. I only
know that they aren't directly accessed by the driver and so the only
potential current use would be as hardware internal buffers. For now keep
them to avoid regressions and only remove the double cursor allocation.
The most changes were caused by renames and the mentioned structure
changes so the chance of regressions is pretty low. The meaning of
viafb_accel changed slightly as previously it was changed back and forth
in the code and allowed to enable the hardware acceleration by software if
previously disabled. The new behaviour is that viafb_accel=0 always
prevents hardware acceleration. With viafb_accel!=0 the acceleration can
be freely choosen by set_var. This means viafb_accel is a diagnostic tool
and if someone has to use viafb_accel=0 the driver needs to be fixed.
As this is mostly a code cleanup no regressions beside the slightly change
of viafb_accel is expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the pitch handling up and replaces the calculation from virtual xres
and bpp with fix.line_length which already contains the pitch and does not
add any constrains for the virtual resolution.
Also add a bit to the second pitch which the documentation mentions but
which was ignored by the driver.
Although it is a bit unclear what the right pitch for some LCD modes is
this patch should have no negative runtime impact.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean the hardware cursor handling up.
The most notable change is that it no longer buffers the values in
viacursor but uses the ones in cursor instead as they are guaranteed to be
always valid.
Furthermore it uses local instead global variables where possible, moves
the cursor variable in shared as only one hardware cursor is supported and
returns an error if memory allocation fails. Last but not least it fixes
a too small buffer (as u32 has only 4 and not 32 bytes) but this did not
produce any known problems.
This is mostly a code cleanup, no negative runtime changes are expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is a completly rewritten 2D engine. The engine is no longer in
a default state but reinitialized every time to allow usage for both
framebuffers regardless of their settings.
The whole engine handling is concentrated in a big function which takes 16
parameters. Although the number of parameters is worryingly it is good to
have a single funtion to deal with this stuff as it allows to easily
support different engines and avoids some code duplication.
On the way support for the new 2D engine in VX800 was added. As the with
less code duplication but it is probably better to duplicate the code as
this way is easier to walk if VIA ever decides to release a new engine
which changes anything the driver touches.
The engine support for VX800 gives a notable boost in speed. There are no
known regressions but as this patch changes paths I do neither have the
hardware nor documentation to check and has the possibility to put the
system in a critical state heavy testing is appreciated.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces viafb_shared and is the beginning of a smooth
transition to use it.
viafb_shared should contain all general, non-surface specific data that
should be shared along all viafb framebuffers while viafb_par should only
contain things that are specific to each surface or in other words extend
fb_info. This change is intended to clean the dual/multi framebuffer
handling up.
This removes the annoyance that viafbinfo1->par points to a different
structure than viaparinfo1.
As the last change is fundamental it is difficult to ensure that all parts
of the driver do not depend on the previous brokenness but the chance of
regressions is very low.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes the completly useless io variable as well as the temporary
used variables mmio_base and mmio_len in favor to use directly the fb_info
variables.
This is a code cleanup only, no runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At least for VX800 this initialization is not very good as some parts of
the register are written with reserved values. This makes the display go
white in some configurations and not usable until the framebuffer is
removed. It's better to not initialize it as it allows to use a
previously (by BIOS) correctly configured display.
This patch makes some displays work but might cause problems on others.
This is bad but can not be easily avoided. If this causes some
regressions it's probably the best to fix it in the 'active' display setup
code.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove everything related to video devices from the driver as it did not
influence the driver operation. This patch does change the userspace
behaviour as it removes two IOCTLs and one module parameter. But this is
good as it removes useless stuff and helps the user to figure out the
options that do affect the driver behaviour (which are still too many).
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean the handling of ioremapped video memory up. The following changes
were made:
info->screen_base - viafb_FB_MM
(VRAM offset calculation) was replaced by
info->fix.smem_start - viafbinfo->fix.smem_start
which is essentially the same calculation but done with physical instead
virtual addresses.
*->fbmem_virt
was replaced by
viafbinfo->screen_base
This is true for viafbinfo and viafbinfo1 as the par pointers are equal.
An early initialization of viafbinfo1->fix.smem* was removed as done later
in viafb_setup_fixinfo.
This patch highlights that the only usage of the ioremapped video memory
in the driver is for hardware cursor handling. Even if it has to hold the
used virtual screen mapped for old-fashioned read/write calls (vs.
mmap'ed) a lot virtual memory could be saved by only ioremapping on
demand.
Code cleanup, no runtime changes expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean the duoview handling up by replacing the varible with the funtion in
the only place where it is used. This is a code cleanup only, no runtime
change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the mode information from viafbdev.c and uses the one of viamode.c
instead. This is possible because horizontal and vertical address are the
same as horizontal and vertical resolution. The reduced blanking modes in
the table are no problem because they have a higher index than the normal
modes and therefore always the normal modes are selected just as the old
behaviour.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unneeeded declarations from the header and makes it more
maintainable by evaluating the array size in the file the array exist in
and exporting it via variables. This removes the need to keep the array
size in the header in sync with the real array size.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the returned error code for remapping the video framebuffer.
Introduce error handling for remapping MMIO register address space to
avoid a NULL pointer dereference. Disable hardware acceleration if
remapping MMIO register address space failed as those registers are only
used for hardware acceleration.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move individual start address setting to viafb_set_primary_address and
viafb_set_secondary_address and make it more flexible to reuse it for
panning. Using central functions makes it easier to follow HW
manipulations.
Remove crt locking as it should be only needed for timing manipulation.
Move iga_path manipulation to via_pci_probe.
Remove memset for screen cleaning as it is currently done only for the
second screen. This is not needed for normal operation but has a little
chance of causing unwanted display artifacts. This can be fixed later
more consistent and more efficient (using viafb_fillrect) if needed.
This is a code clenup, no notable runtime changes expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shrink and merge viafb_update_viafb_par. This removes a lot of duplicated
data in viafb_par. Use the relevant data of fb_info instead. On the way
it removes an inconsistency in handling a second framebuffer which only
worked because viafbinfo1->par is modified to point to the same viafb_par
as viafbinfo->par.
Code cleanup only, no runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the start address is set to an initial value every time
viafb_setmode is called.
This is not done consistently along graphic cores and not even the whole
address but often only parts of it. On top of that it seems useless as
the real/final address will be set by viafb_set_start_addr a few lines
later.
Remove this superfluous initalization to shrink register initalization and
as a start to decouple primary and secondary display. Code cleanup, no
notable runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code initializes the register for CX700 chips 2 times due to a
missing break as discovered by Harald Welte.
As CX700 and VX800 have exactly the same register initialization we can
use one for both to avoid duplicated code.
As this is a pure code cleanup no measurable runtime effects are expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EP93xx video driver plus documentation.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Daniele Venzano <linux@brownhat.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If called with mode_idx = 1, rate = 68, a read occurs from
sisfb_vrate[-1].refresh.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the previous version, return values in ioctl() function have been
modified.
[akpm@linux-foundation.org: simplify lcd_disable_raster()]
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add LCD controller (LCDC) driver for TI's DA8xx/OMAP-L1xx architecture.
LCDC specifications can be found at http://www.ti.com/litv/pdf/sprufm0a.
LCDC on DA8xx consists of two independent controllers, the Raster
Controller and the LCD Interface Display Driver (LIDD) controller. LIDD
further supports character and graphic displays.
This patch adds support for the graphic display (Sharp LQ035Q3DG01) found
on the DA830 based EVM. The EVM details can be found at:
http://support.spectrumdigital.com/boards/dskda830/revc/.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
DESC
davinci-fb-frame-buffer-driver-for-ti-da8xx-omap-l1xx-fix
EDESC
From: Andrew Morton <akpm@linux-foundation.org>
fix kconfig indenting
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since `+' has a higher precedence than the trinary operator `?', this
added `hres * (1 << color_mode)' to the boolean testing videomode and
depth.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a framebuffer driver for Qualcomm MSM/QSD SoCs, tested on HTC Dream
smartphone (aka T-Mobile G1, aka ADP1).
Brian said:
I did the original quick and dirty version for bringup. Rebecca took
over and (re)wrote the bulk of the driver, getting things stable for
production ship of Dream and Sapphire, and Dima is currently adding
support for later Qualcomm chipsets (QSD8x50, etc).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Rebecca Schultz Zavin <rebecca@android.com>
Cc: Dima Zavin <dima@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bunch of coding style problems in atyfb_base.c.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "H Hartley Sweeten" <hartleys@visionengravers.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes the following:
warning: assignment discards qualifiers from pointer target type
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also move the controller specific options up in the menu, to a more
logical spot.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- use __iomem type attribute where appropriate
- expand (a ? : b) to (a ? a : b)
As suggested by Russel King <linux@arm.linux.org.uk>
- remove a dead line from omapfb_main.c
Signed-off-by: Arun C <arunedarath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check wether fbdev is NULL in suspend / resume functions. Fbdev is
NULL, if there is no lcd or it is not enabled in configuration.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, the only external (to dispc.c) IRQ handler was RFBI's frame
done handler. dispc's IRQ framework was very dumb: you could only have
one handler, and the semantics of {request,free}_irq were odd, to say the
least.
The new framework allows multiple consumers to register arbitrary IRQ
masks.
Signed-off-by: Daniel Stone <daniel.stone@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without wakeup enable omap doesn't wake up on dispc interrupts. This
causes problems in a case where mpu is in sleep state and dispc interrupt
fires.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leaving interface clocks enabled causes dss pwrdm to stay in active state
when mpu is in active state. This fix puts dss to sleep state when it is
not needed.
Earlier version broke framebuffer on 24xx. This is fixed by enabling
clocks before trying to access DISPC_IRQSTATUS register.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- value and register offset was swapped in a dispc write
- DISPC_CONTROL register was used instead of DISPC_SYSCONFIG
- FIFO size bit field had incorrect length for OMAP3
Fixed-by: arun <arunedarath@mistralsolutions.com>
Fixed-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Fixed-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD controller (EPSON S1D13744) supports rotation (0, 90, 180 and 270
degrees) on hardware just setting the bits 0 and 1 of 0x28 register (LCD
Panel Configuration Register). Now it is possible to use this caps only
setting the angle degree on var rotate of fb_var_screeninfo using the
FBIOPUT_VSCREENINFO ioctl.
Fixed-by: Siarhei Siamashka <siarhei.siamashka@nokia.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@openbossa.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add glue to control the OMAP_LDP LCD as a frame buffer device using the
existing dispc.c driver under omapfb.
Patch updated for mainline kernel. Note that the drivers/video/omap
should be updated to pass omap_lcd_config in platform_data. The patch
should also be updated to compile if twl4030 is not selected, and
eventually to use the regulator framework.
Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com>
Fixed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default resolution is 1024x768@24bit
This version addresses the comments from Felipe Balbi adn Arun Edarath
Fixed-by: Felipe Contreras <felipe.contreras@gmail.com>
Fixed-by: Steve Sakoman <steve@sakoman.com>
Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com>
Fixed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Koen Kooi <koen@openembedded.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add LCD support for OMAP3 EVM
Backlight support by Arun C <arunedarath@mistralsolutions.com>
Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com>
Fixed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 3430SDP uses the same panel as the 2430SDP. The main difference are
in the GPIO lines used for panel enable and backlight, and the VAUX
register/commands sent to the TWL4030 power subsystem.
Also, some misc. whitespace cleanups.
Fixed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@mvsita.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
omap2evm LCD supports VGA and QVGA resolution, by default its in VGA mode.
Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com>
Fixed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Arun C <arunedarath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add glue to control the 2430SDP LCD as a frame buffer device using the
existing dispc.c driver under omapfb.
Fixed-by: Kevin Hilman <khilman@mvista.com>
Fixed-by: Sergio Aguirre <saaguirre@ti.com>
Fixed-by: Francisco Alecrim <francisco.alecrim@indt.org.br>
Fixed-by: Tony Lindgren <tony@atomide.com>
Fixed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Hunyue Yau <hyau@mvista.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an updated version of the LCD driver for the Amstrad Delta to take
into account the recent changes to the omapfb infrastructure. The Delta
features a 480x320 12 bit DSTN panel.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed-by: Mike Wege <ext-mike.wege@nokia.com>
Fixed-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Fixed-by: Timo Savola <tsavola@movial.fi>
Fixed-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Fixed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many gpio chips allow to generate interrupts when the value of a pin
changes. This patch gives usermode application the opportunity to make
use of this feature by calling poll(2) on the /sys/class/gpio/gpioN/value
sysfs file. The edge to trigger can be set in the edge file in the same
directory. Possible values are "none", "rising", "falling", and "both".
Using level triggers is not possible with current sysfs since nothing
changes the GPIO value (and the IRQ keeps triggering). Edge triggering
will "just work". Note that if there was an event between read() and
poll(), the poll() returns immediately.
Also note that this version only supports true GPIO interrupts. Some
later patch might be able to synthesize this behavior by timer-driven
polling; some systems seem to need that.
[dbrownell@users.sourceforge.net: align ids to 16 bit ids; whitespace]
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers should be including <linux/gpio.h> not <asm/gpio.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MAX7315 is pin and software compatible with PCA9534, so add it to the I2C
device ID table of pca953x driver.
http://www.datasheetcatalog.org/datasheet/maxim/MAX7315.pdf
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Langwell chip is the IO hub for Intel Moorestown platform which has a
64-pin gpio block device inside. It is exposed as a dedicated PCI device.
We use it to control outside peripheral as well as to do IRQ demuxing.
The gpio block uses MSI to send level type interrupt to IOAPIC.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Freescale MC33880 High/Low side switch
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 926b663ce8 (gpiolib: allow GPIOs to
be named) already provides naming on the chip level. This patch provides
more flexibility by allowing multiple names where ever in sysfs on a per
GPIO basis.
Adapted from David Brownell's comments on a similar concept:
http://lkml.org/lkml/2009/4/20/203.
[randy.dunlap@oracle.com: fix build for CONFIG_GENERIC_GPIO=n]
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_RTC_HCTOSYS allows the kernel to read the system time from the RTC
at boot and resume, avoiding the need for userspace to do so.
Unfortunately userspace currently has no way to know whether this
configuration option is enabled and thus cannot sensibly choose whether to
run hwclock itself or not. Add a hctosys sysfs attribute which indicates
whether a given RTC set the system clock.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two new-ish runtime warnings in the at91rm9200 (etc) RTC:
Platform driver 'at91_rtc' needs updating - please use dev_pm_ops
... by just switching
IRQ 1/at91_rtc: IRQF_DISABLED is not guaranteed on shared IRQs
... no longer needed now that rtc_update_irq() changed
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code is not executed before ds1307->rtc has been successfully
initialized to the result of calling rtc_device_register. Thus the test
that ds1307->rtc is not NULL is always true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@match exists@
expression x, E;
statement S1, S2;
@@
x = rtc_device_register(...)
... when != x = E
(
* if (x == NULL || ...) S1 else S2
|
* if (x == NULL && ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ospite@studenti.unina.it: get pcap data from the parent device]
Signed-off-by: guiming zhuo <gmzhuo@gmail.com>
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for RTC on the Freescale STMP37xx/378x platform.
Signed-off-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin RTC IRQ is an internal interrupt, so it makes no sense to
have it be shared.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the RTC COH 901 331 found in the ST-Ericsson U300
series mobile platforms to the RTC subsystem. It integrates to the ARM
kernel support recently added to RMKs ARM tree and will be enabled in the
U300 defconfig in due time.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for Freescale's MXC internal real time clock modules.
The code is taken from Freescale's BSPs, but modified to fit the current
kernel coding mechanisms. Also, the PMIC external clock function was
removed for now to not add dead bits and keep the code as simple as
possible.
[akpm@linux-foundation.org: make PIE_BIT_DEF[] static]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Philips/NXP PCF2123 RTC.
Signed-off: Chris Verges <chrisv@cyberswitching.com>
Tested-by: Chris Verges <chrisv@cyberswitching.com>
Signed-off: Christian Pellegrin <chripell@fsfe.org>
Tested-by: Christian Pellegrin <chripell@fsfe.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support two new half-duplex SPI implementation restrictions, for links
that talk to TX-only or RX-only devices. (Existing half-duplex flavors
support both transfer directions, just not at the same time.)
Move spi_async() into the spi.c core, and stop inlining it. Then make
that function perform error checks and reject messages that demand more
than the underlying controller can support.
Based on a patch from Marek Szyprowski which did this only for the
bitbanged GPIO driver.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tAdd adds McSPI support for OMAP4430 SDP platform. All the base addresses
are changed between OMAP1/2/3 and OMAP4. The fields of the resource
structures are filled at runtime to have McSPI support on OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previous restore was lazy and only restored CHxCONF when it was needed by
a specific chip select. This could cause occasional errors on an SPI bus
where multiple chip selects are in use.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the update to the spi_bitbang driver, the transfer setup code is
being called more often, and thus is often re-doing calculations that have
been done before. The SPI layer allows our driver to add its own data to
each device so add a result cache to each device.
This should also remove the problem where we where directly setting up
registers in the setup call which meant we might overwrite the state of an
extant transfer.,
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the spi_s3c24xx driver to use dev_pm_ops to avoid the following
warning during probe:
Platform driver 's3c2410-spi' needs updating - please use dev_pm_ops
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the use of (res->end - res->start) to use resource_size() to
get the size of the resource.
Signed-off-by; Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver includes <asm/io.h> where it should be including <linux/io.h>
and also includes <mach/hardware.h> and <asm/dma.h> without using anything
from these.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register pxa2xx_spi earlier so it can be used with cpufreq
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the code a little bit nicer, and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the code a little bit nicer, and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alias isn't needed any longer since the m25p80 driver converted to the
module device table matching.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this patch spi drivers can use standard spi_driver.id_table and
MODULE_DEVICE_TABLE() mechanisms to bind against the devices. Just like
we do with I2C drivers.
This is useful when a single driver supports several variants of devices
but it is not possible to detect them in run-time (like non-JEDEC chips
probing in drivers/mtd/devices/m25p80.c), and when platform_data usage is
overkill.
This patch also makes life a lot easier on OpenFirmware platforms, since
with OF we extensively use proper device IDs in modaliases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the PL022 driver a default choice for any RealView and
Versatile boards plus the integrator IMPD1 which all contain the PL022
PrimeCell. This will make it a default choice if and only if a user
selects SPI support for their board.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a SPI driver for the SPI controller found in the IBM/AMCC
4xx PowerPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert bit shifted values into BIT format
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is in a non working state at the moment and will be replaced
by a bitbang driver which can also handle the newer i.MX variants
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Originally, walk_memory_resource() was introduced to traverse all memory
of "System RAM" for detecting memory hotplug/unplug range. For doing so,
flags of IORESOUCE_MEM|IORESOURCE_BUSY was used and this was enough for
memory hotplug.
But for using other purpose, /proc/kcore, this may includes some firmware
area marked as IORESOURCE_BUSY | IORESOUCE_MEM. This patch makes the
check strict to find out busy "System RAM".
Note: PPC64 keeps their own walk_memory_resouce(), which walk through
ppc64's lmb informaton. Because old kclist_add() is called per lmb, this
patch makes no difference in behavior, finally.
And this patch removes CONFIG_MEMORY_HOTPLUG check from this function.
Because pfn_valid() just show "there is memmap or not* and cannot be used
for "there is physical memory or not", this function is useful in generic
to scan physical memory range.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On an OLPC XO-1.5 development board with Via VX855 chipset, the sdhci
controller can take up to 12ms to stabilize its clock, but the current
timeout at which we give up on the controller is 10ms.
The patch increases the timeout delay rather than using a device-specific
quirk -- since we exit the loop when the clock comes up, increasing the
timeout value will only make us mdelay() longer in the errant case of a
device with a clock that is not stabilizing, which it seems worth waiting
a little longer for in general.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for ADMA on SDHCI hosts, not supporting SDMA.
According to the SDHCI specifications a host can support ADMA but not SDMA
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Especially with the PM framework, those are quite handy to have in driver
code too.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Especially for SDIO drivers which may have special conditions/errors to
report, it is a good thing to relay the returned error code back to upper
layers.
This also allows for the rationalization of the resume path where code to
"remove" a no-longer-existing or replaced card was duplicated into the
MMC, SD and SDIO bus drivers.
In the SDIO case, if a function suspend method returns an error, then all
previously suspended functions are resumed and the error returned. An
exception is made for -ENOSYS which the core interprets as "we don't
support suspend so just kick the card out for suspend and return success".
When resuming SDIO cards, the core code only validates the manufacturer
and product IDs to make sure the same kind of card is still present before
invoking functions resume methods. It's the function driver's
responsibility to perform further tests to confirm that the actual same
card is present (same MAC address, etc.) and return an error otherwise.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all SDIO cards are virtually removed upon a suspend, and
completely reprobed upon a resume. This adds the suspend and resume
methods to the SDIO bus driver so to be able to dispatch those events to
the actual SDIO function drivers for real suspend/resume instead.
All active functions on a card must have a driver with both a suspend and
a resume method though. Failing that, we fall back to the current
behavior of simply "removing" the card when suspending.
When resuming, we make sure the same card is still inserted by comparing
the vendor and product IDs. If there is a mismatch, or if there is simply
no card anymore in the slot, then the previous card is "removed" and the
new card is detected. This is further enhanced with the next patch.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some time ago, I have send a patch to the mmc_spi subsystem changing the
error codes. This was after a discussion with Pierre about using EINVAL
only for non-recoverable errors. This patch was accepted as
http://git.kernel.org/linus/fdd858db7113ca64132de390188d7ca00701013d
Unfortunately, several weeks later, I realized that this patch has opened
a little can of worms because there are SD cards on the market which
a) claim that they support the switch command
AND
b) refuse to execute this command if operating in SPI mode.
So, such a card would get unusuable in an embedded linux system in SPI
mode, because the init sequence terminates with an error.
This patch adds the missing error codes to the caller of the switch
command and restores the old behaviour to fail gracefully if these
commands can not execute.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org> [2.6.31.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add basic support for all 5 MMC controllers on OMAP4.
This patch doesn't include mmc-regulator support
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
