* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
Currently atmel_nand driver used by AT91 and AVR32 calls a special callback
which return nand partition table and number of partitions. However in all
boards this callback returns just static data. So drop this callback and
make atmel_nand use partition table provided statically via platform_data.
Nicolas Ferre: I am in favor for a mainline inclusion through linux-mtd tree.
Hans-Christian Egtvedt: I'm fine by sending the changes for AVR32 through linux-mtd
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
they are the same except the default priority
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.
On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000
This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
select ARM_PATCH_PHYS_VIRT
as with ARM_PATCH_PHYS_VIRT you can patch boot_params at runtime or any recent
bootloader will provide a valid atags pointer in r2
as point out by Russell on AT91 we never use XIP
so se do not need PLAT_PHYS_OFFSET
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
switch early init to init_early and introduce soc map_io
with this Patch we will not do any more early device setup during the map io
tks to Russell to point the new call back
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Andrew Victor <linux@maxim.org.za>
no board configure it as 'n' and it's an issue to merge all defconfigs
in one
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
so will pass it via system_rev
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The change introduced in patch 5596/1 used incorrect bracing which
resulted in the AT24 EEPROM no longer being registered. This patch
corrects the bracing and allows both the WM8731 audio device and AT24
EEPROM device to be registered.
Signed-off-by: Rob Alley <rob.alley@navmanwireless.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DBGU means Debug Unit, was refered as "DGBU" in some files. Fixed to "DBGU".
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WM8731 driver has been updated to allow registration via normal
device model methods rather than from within the ASoC driver probe
so update the AT91SAM9G20-EK to make use of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add board information about on-board I2C eeprom AT24C512N at 0x50.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91SAM20-EK has a WM8731 attached to it with MCLK supplied from
PCLK0 and the digital audio interface supplied by SSC0.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.
The following boards have been modified:
cam60 : NAND
cap9adk : NAND, NOR
qil-a9260 : NAND
sam9-l9260 : NAND
sam9260ek : NAND
sam9261ek : DM9000 Ethernet, NAND
sam9263 : NAND
sam9g20ek : NAND
sam9rlek : NAND
usb-a9260 : NAND
usb-a9263 .: NAND
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the various AT91 board files, replace hard-coded size values (eg,
0x800000) with the SZ_ size definitions (eg, SZ_8M) from sizes.h
Also replace MTD partition offsets with MTDPART_OFS_NXTBLK.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Structs called at91_nand_data where renamed to atmel_nand_data
and configs called *MTD_NAND_AT91* where renamed to
*MTD_NAND_ATMEL*. This was unfortunately not done consistently,
causing NAND chips not being initialised on several ARM boards.
I am aware that the author of the original change did not rename
MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example.
All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order
to keep naming consistency.
This patch was only tested on a MACH_SAM9_L9260, as this is the
only ARM board I have to my disposal.
Before this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
105
$ git-ls-files |xargs grep at91_nand |wc -l
4
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
8
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
47
After this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
109
$ git-ls-files |xargs grep at91_nand |wc -l
0
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
55
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
0
Signed-off-by: Pieter du Preez <pdupreez@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
struct at91_nand has been renamed atmel_nand. Fix the four boards that
were added since the patch was created.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>