Add mlx4_devlink_reload() to support devlink reload operation.
Add mlx4_devlink_param_load_driverinit_values() to load values which
were set using driverinit configuration mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create initial parameters table for mlx4.
The table consists of two generic parameters and two driver-specific
parameters.
Generic:
internal_err_reset - Enable reset device on internal errors. This
parameter can be configured on mlx4 either on runtime or during driver
initialization.
max_macs - Max number of MACs per ETH port. For mlx4 this parameter
value range is between 1 and 128. This parameter can be configured on
mlx4 only during driver initialization.
Driver specific:
enable_64b_cqe_eqe - Enable 64 byte CQEs/EQEs when the FW supports it.
This parameter can be configured on mlx4 only during driver
initialization.
enable_4k_uar - Enable using 4K UAR. This parameter can be configured on
mlx4 only during driver initialization.
Register the parameters table on mlx4_init_one() and unregister on
mlx4_remove_one().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer skb is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'skb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer ndev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'ndev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:525:5: warning:
symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:536:5: warning:
symbol 'hw_atl_utils_mpi_set_state' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When runtime-suspending we configure WoL w/o touching saved_wolopts.
If saved_wolopts == 0 we would power down the PHY in this case what's
wrong. Therefore we have to check the actual chip WoL settings here.
Fixes: 433f9d0ddc ("r8169: improve saved_wolopts handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In highly constrained resources environments (like the 124VF
T5 and 248VF T6 configurations), PF4 may not have very many
resources at all and we need to adapt to whatever we've been
allocated, this patch adds support to get the provisioned
resources.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'irq' is being assigned but is never used hence it is
and can be removed.
Cleans up clang warning:
warning: variable 'irq' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable old_vlan is being assigned but is never used hence it is
and can be removed.
Cleans up clang warning:
warning: variable 'old_vlan' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer 'name' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'name' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer 'info' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'info' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer pfhwdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'pfhwdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'protocol' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'protocol' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable last_rule_idx is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'last_rule_idx' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'inc' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'inc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer req and variable func are being assigned but are never used
hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'req' set but not used [-Wunused-but-set-variable]
warning: variable 'func' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'freed' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'freed' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer rxd is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'rxb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable old_duplex is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'old_duplex' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer rxdesc is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'rxdesc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement HW offload support for SO_TXTIME through igb's Launchtime
feature. This is done by extending igb_setup_tc() so it supports
TC_SETUP_QDISC_ETF and configuring i210 so time based transmit
arbitration is enabled.
The FQTSS transmission mode added before is extended so strict
priority (SP) queues wait for stream reservation (SR) ones.
igb_config_tx_modes() is extended so it can support enabling/disabling
Launchtime following the previous approach used for the credit-based
shaper (CBS).
As the previous flow, FQTSS transmission mode is enabled automatically
by the driver once Launchtime (or CBS, as before) is enabled.
Similarly, it's automatically disabled when the feature is disabled
for the last queue that had it setup on.
The driver just consumes the transmit times from the skbuffs directly,
so no special handling is done in case an 'invalid' time is provided.
We assume this has been handled by the ETF qdisc already.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb_tx_timestamp() is being called before the Tx
descriptors are prepared in igb_xmit_frame_ring(), which happens
during either the igb_tso() or igb_tx_csum() calls.
Given that now the skb->tstamp might be used to carry the timestamp
for SO_TXTIME, we must only call skb_tx_timestamp() after the
information has been copied into the Tx descriptors.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split code into a separate function (igb_offload_apply()) that will be
used by ETF offload implementation.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the data transmission arbitration algorithm - DataTranARB
field on TQAVCTRL reg - is always set to CBS when the Tx mode is
changed from legacy to 'Qav' mode.
Make that configuration a bit more granular in preparation for the
upcoming Launchtime enabling patches, since CBS and Launchtime can be
enabled separately. That is achieved by moving the DataTranARB setup
to igb_config_tx_modes() instead.
Similarly, when disabling CBS we must check if it has been disabled
for all queues, and clear the DataTranARB accordingly.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this function retrieve what it needs from the Tx ring being
addressed since it already relies on what had been saved on it before.
Also, since this function will be used by the upcoming Launchtime
patches rename it to better reflect its intention. Note that
Launchtime is not part of what 802.1Qav specifies, but the i210
datasheet refers to this set of functionality as "Qav Transmission
Mode".
Here we also perform a tiny refactor at is_any_cbs_enabled(), and add
further documentation to igb_setup_tx_mode().
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improves packet rate of 1-byte UDP receives by up to 10%.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-03
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various improvements to bpftool and libbpf, that is, bpftool build
speed improvements, missing BPF program types added for detection
by section name, ability to load programs from '.text' section is
made to work again, and better bash completion handling, from Jakub.
2) Improvements to nfp JIT's map read handling which allows for optimizing
memcpy from map to packet, from Jiong.
3) New BPF sample is added which demonstrates XDP in combination with
bpf_perf_event_output() helper to sample packets on all CPUs, from Toke.
4) Add a new BPF kselftest case for tracking connect(2) BPF hooks
infrastructure in combination with TFO, from Andrey.
5) Extend the XDP/BPF xdp_rxq_info sample code with a cmdline option to
read payload from packet data in order to use it for benchmarking.
Also for '--action XDP_TX' option implement swapping of MAC addresses
to avoid drops on some hardware seen during testing, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds ethtool -r|--negotiate operation support. It triggers special
control bit on FW interface causing FW to restart link negotiation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Runtime change of pause frame configuration (rx/tx flow control)
via ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now pass link drop status to FW on init/deinit. This is required
to inform FW that driver took/released a control on link.
FW then will manage its own state and device power profile based
on this information. To improve management we remove mpi_set
function which ambiguously took both state and speed parameters.
Deinit callback is now a part of FW ops, as it actually manages the FW.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented ring size setup, min/max validation and reconfiguration in
runtime.
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suffix UL to constant 1024 in order to give the compiler complete
information about the proper arithmetic to use. Notice that this
constant is used in a context that expects an expression of type
u64 (64 bits, unsigned) and following expressions are currently
being evaluated using 32-bit arithmetic:
qopt->idleslope * 1024 * ptr
qopt->hicredit * 1024 * 8
qopt->locredit * 1024 * 8
Addresses-Coverity-ID: 1470246 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470248 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1470249 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, prefix hnae_ should be modified to hnae3_.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reference to Documentation/DMA-API-HOWTO.txt,
Streaming DMA mappings which are usually mapped for one DMA transfer,
Network card DMA ring descriptors should use Consistent DMA mappings.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give default option for HNS3_HCLGE and HNS3_ENET will be helpful,
while dependency HNS3 is set. Meanwhile, use "if HNS3" section
instead of all the "depends on HNS3".
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some members in struct hns3_enet_tqp_vector, struct hnae3_client
and struct hnae3_ae_algo are unused.
This patch removes them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set complete in the first hclge_cmd_csq_done of hclge_cmd_send,
and check if complete later, unnecessary to do hclge_cmd_csq_done
again.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
csq is used as a ring buffer, the value of the desc will be replaced
in next use. This patch removes the unnecessary memset, and just
updates the next_to_clean.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some redundant assignments.
desc->flag = cpu_to_le16(HCLGE_CMD_FLAG_NO_INTR | HCLGE_CMD_FLAG_IN)
has set bit HCLGE_CMD_FLAG_WR to zero, so does others.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some useless type cast, print in hclge_cmd_send.
This patch removes them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_ring_to_dma_dir is unused anywhere.
This patch removes it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hack (affecting the non-PCIe models only) was introduced in 2004
to deal with link negotiation failures in 1GBit mode. Based on a
comment in the r8169 vendor driver I assume the issue affects RTL8169sb
in combination with particular 1GBit switch models.
Resetting the PHY every 10s and hoping that one fine day we will make
it to establish the link seems to be very hacky to me. I'd say:
If 1GBit doesn't work reliably in a users environment then the user
should remove 1GBit from the advertised modes, e.g. by using
ethtool -s <if> advertise <10/100 modes>
If the issue affects one chip version only and that with most link
partners, then we could also think of removing 1GBit from the
advertised modes for this chip version in the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.
Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct size value while copying chassis/port id values.
Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-07-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) A bpf_fib_lookup() helper fix to change the API before freeze to
return an encoding of the FIB lookup result and return the nexthop
device index in the params struct (instead of device index as return
code that we had before), from David.
2) Various BPF JIT fixes to address syzkaller fallout, that is, do not
reject progs when set_memory_*() fails since it could still be RO.
Also arm32 JIT was not using bpf_jit_binary_lock_ro() API which was
an issue, and a memory leak in s390 JIT found during review, from
Daniel.
3) Multiple fixes for sockmap/hash to address most of the syzkaller
triggered bugs. Usage with IPv6 was crashing, a GPF in bpf_tcp_close(),
a missing sock_map_release() routine to hook up to callbacks, and a
fix for an omitted bucket lock in sock_close(), from John.
4) Two bpftool fixes to remove duplicated error message on program load,
and another one to close the libbpf object after program load. One
additional fix for nfp driver's BPF offload to avoid stopping offload
completely if replace of program failed, from Jakub.
5) Couple of BPF selftest fixes that bail out in some of the test
scripts if the user does not have the right privileges, from Jeffrin.
6) Fixes in test_bpf for s390 when CONFIG_BPF_JIT_ALWAYS_ON is set
where we need to set the flag that some of the test cases are expected
to fail, from Kleber.
7) Fix to detangle BPF_LIRC_MODE2 dependency from CONFIG_CGROUP_BPF
since it has no relation to it and lirc2 users often have configs
without cgroups enabled and thus would not be able to use it, from Sean.
8) Fix a selftest failure in sockmap by removing a useless setrlimit()
call that would set a too low limit where at the same time we are
already including bpf_rlimit.h that does the job, from Yonghong.
9) Fix BPF selftest config with missing missing NET_SCHED, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the NFP fw only supports L3/L4 hashing so rejects the offload of
filters that output to LAG ports implementing other hash algorithms. Team,
however, uses a BPF function for the hash that is not defined. To support
Team offload, accept hashes that are defined as 'unknown' (only Team
defines such hash types). In this case, use the NFP default of L3/L4
hashing for egress port selection.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
