Commit Graph

3590 Commits

Author SHA1 Message Date
Babu Moger
c289d0eff3 drivers/usb: Skip auto handoff for TI and RENESAS usb controllers
Never seen XHCI auto handoff working on TI and RENESAS cards.
Eventually, we force handoff. This code forces the handoff
unconditionally. It saves 5 seconds boot time for each card.

Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-07 10:12:22 +01:00
Bryan Paluch
ed6d6f8f42 usb: increase ohci watchdog delay to 275 msec
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"

Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-24 14:30:32 +02:00
Masahiro Yamada
1e4b434875 usb: ehci-platform: increase EHCI_MAX_RSTS to 4
Socionext LD11 SoC (arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi)
needs to handle 4 reset lines for EHCI.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-24 14:29:08 +02:00
Wenyou Yang
ed19ece135 usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
The reset value of RWC is 0, set RemoteWakeupConnected bit explicitly
before calling ohci_run, it also fixes the issue that the mass
storage stick connected wasn't suspended when the system suspend.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-24 14:29:08 +02:00
Mathias Nyman
7d3b016a6f xhci: use default USB_RESUME_TIMEOUT when resuming ports.
USB2 host inititated resume, and system suspend bus resume
need to use the same USB_RESUME_TIMEOUT as elsewhere.

This resolves a device disconnect issue at system resume seen
on Intel Braswell and Apollolake, but is in no way limited to
those platforms.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-20 17:54:55 +02:00
Mathias Nyman
346e99736c xhci: workaround for hosts missing CAS bit
If a device is unplugged and replugged during Sx system suspend
some  Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.

A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.

Intel 100/c230 series PCH specification update Doc #332692-006 Errata 

Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-20 17:54:55 +02:00
Mathias Nyman
4c39135aa4 xhci: add restart quirk for Intel Wildcatpoint PCH
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.

Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-20 17:54:55 +02:00
Linus Torvalds
133d970e0d Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "This is the main MIPS pull request for 4.9:

  MIPS core arch code:
   - traps: 64bit kernels should read CP0_EBase 64bit
   - traps: Convert ebase to KSEG0
   - c-r4k: Drop bc_wback_inv() from icache flush
   - c-r4k: Split user/kernel flush_icache_range()
   - cacheflush: Use __flush_icache_user_range()
   - uprobes: Flush icache via kernel address
   - KVM: Use __local_flush_icache_user_range()
   - c-r4k: Fix flush_icache_range() for EVA
   - Fix -mabi=64 build of vdso.lds
   - VDSO: Drop duplicated -I*/-E* aflags
   - tracing: move insn_has_delay_slot to a shared header
   - tracing: disable uprobe/kprobe on compact branch instructions
   - ptrace: Fix regs_return_value for kernel context
   - Squash lines for simple wrapper functions
   - Move identification of VP(E) into proc.c from smp-mt.c
   - Add definitions of SYNC barrierstype values
   - traps: Ensure full EBase is written
   - tlb-r4k: If there are wired entries, don't use TLBINVF
   - Sanitise coherentio semantics
   - dma-default: Don't check hw_coherentio if device is non-coherent
   - Support per-device DMA coherence
   - Adjust MIPS64 CAC_BASE to reflect Config.K0
   - Support generating Flattened Image Trees (.itb)
   - generic: Introduce generic DT-based board support
   - generic: Convert SEAD-3 to a generic board
   - Enable hardened usercopy
   - Don't specify STACKPROTECTOR in defconfigs

  Octeon:
   - Delete dead code and files across the platform.
   - Change to use all memory into use by default.
   - Rename upper case variables in setup code to lowercase.
   - Delete legacy hack for broken bootloaders.
   - Leave maintaining the link state to the actual ethernet/PHY drivers.
   - Add DTS for D-Link DSR-500N.
   - Fix PCI interrupt routing on D-Link DSR-500N.

  Pistachio:
   - Remove ANDROID_TIMED_OUTPUT from defconfig

  TX39xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  TX49xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  txx9wdt:
   - Add missing clock (un)prepare calls for CCF

  BMIPS:
   - Add PW, GPIO SDHCI and NAND device node names
   - Support APPENDED_DTB
   - Add missing bcm97435svmb to DT_NONE
   - Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
   - Add DT examples for BCM63268, BCM3368 and BCM6362
   - Add support for BCM3368 and BCM6362

  PCI
   - Reduce stack frame usage
   - Use struct list_head lists
   - Support for CONFIG_PCI_DOMAINS_GENERIC
   - Make pcibios_set_cache_line_size an initcall
   - Inline pcibios_assign_all_busses
   - Split pci.c into pci.c & pci-legacy.c
   - Introduce CONFIG_PCI_DRIVERS_LEGACY
   - Support generic drivers

  CPC
   - Convert bare 'unsigned' to 'unsigned int'
   - Avoid lock when MIPS CM >= 3 is present

  GIC:
   - Delete unused file smp-gic.c

  mt7620:
   - Delete unnecessary assignment for the field "owner" from PCI

  BCM63xx:
   - Let clk_disable() return immediately if clk is NULL

  pm-cps:
   - Change FSB workaround to CPU blacklist
   - Update comments on barrier instructions
   - Use MIPS standard lightweight ordering barrier
   - Use MIPS standard completion barrier
   - Remove selection of sync types
   - Add MIPSr6 CPU support
   - Support CM3 changes to Coherence Enable Register

  SMP:
   - Wrap call to mips_cpc_lock_other in mips_cm_lock_other
   - Introduce mechanism for freeing and allocating IPIs

  cpuidle:
   - cpuidle-cps: Enable use with MIPSr6 CPUs.

  SEAD3:
   - Rewrite to use DT and generic kernel feature.

  USB:
   - host: ehci-sead3: Remove SEAD-3 EHCI code

  FBDEV:
   - cobalt_lcdfb: Drop SEAD3 support

  dt-bindings:
   -  Document a binding for simple ASCII LCDs

  auxdisplay:
   - img-ascii-lcd: driver for simple ASCII LCD displays

  irqchip i8259:
   - i8259: Add domain before mapping parent irq
   - i8259: Allow platforms to override poll function
   - i8259: Remove unused i8259A_irq_pending

  Malta:
   - Rewrite to use DT

  of/platform:
   - Probe "isa" busses by default

  CM:
   - Print CM error reports upon bus errors

  Module:
   - Migrate exception table users off module.h and onto extable.h
   - Make various drivers explicitly non-modular:
   - Audit and remove any unnecessary uses of module.h

  mailmap:
   - Canonicalize to Qais' current email address.

  Documentation:
   - MIPS supports HAVE_REGS_AND_STACK_ACCESS_API

  Loongson1C:
   - Add CPU support for Loongson1C
   - Add board support
   - Add defconfig
   - Add RTC support for Loongson1C board

  All this except one Documentation fix has sat in linux-next and has
  survived Imagination's automated build test system"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
  Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
  MIPS: ptrace: Fix regs_return_value for kernel context
  MIPS: VDSO: Drop duplicated -I*/-E* aflags
  MIPS: Fix -mabi=64 build of vdso.lds
  MIPS: Enable hardened usercopy
  MIPS: generic: Convert SEAD-3 to a generic board
  MIPS: generic: Introduce generic DT-based board support
  MIPS: Support generating Flattened Image Trees (.itb)
  MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
  MIPS: Print CM error reports upon bus errors
  MIPS: Support per-device DMA coherence
  MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
  MIPS: Sanitise coherentio semantics
  MIPS: PCI: Support generic drivers
  MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
  MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
  MIPS: PCI: Inline pcibios_assign_all_busses
  MIPS: PCI: Make pcibios_set_cache_line_size an initcall
  MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
  MIPS: PCI: Use struct list_head lists
  ...
2016-10-15 09:26:12 -07:00
Masahiro Yamada
97139d4a6f treewide: remove redundant #include <linux/kconfig.h>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:

  -include $(srctree)/include/linux/kconfig.h

This commit removes explicit includes except the following:

  * arch/s390/include/asm/facilities_src.h
  * tools/testing/radix-tree/linux/kernel.h

These two are used for host programs.

Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-10-11 15:06:33 -07:00
Paul Burton
63c8d90ca9 USB: host: ehci-sead3: Remove SEAD-3 EHCI code
The SEAD-3 board is now probing its EHCI controller using the generic
EHCI driver & its generic-ehci device tree binding. Remove the unused
SEAD-3 specific EHCI code.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-10-05 01:31:20 +02:00
Rafał Miłecki
e8624859dd USB: bcma: drop Northstar PHY 2.0 initialization code
This driver should initialize controller only, PHY initialization should
be handled by separated PHY driver. We already have phy-bcm-ns-usb2 in
place so let it makes its duty.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-27 12:20:17 +02:00
Tony Lindgren
54a2ec67f1 usb: ohci: Allow ohci on omap5 also
With LPAE config we don't have omap3 or omap4 selected for
omap5 variants.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-13 17:26:32 +02:00
Wei Yongjun
9cdd8e11c2 USB: host: ohci-at91: fix non static symbol warning
Fixes the following sparse warning:

drivers/usb/host/ohci-at91.c:141:15: warning:
 symbol 'at91_dt_syscon_sfr' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-13 17:24:24 +02:00
Wei Yongjun
b175b38a0f usb: host: xhci-tegra: Fix error return code in tegra_xusb_probe()
Fix to return error code -ENOMEM from the usb_create_shared_hcd()
error handling case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-13 17:24:24 +02:00
Greg Kroah-Hartman
fc9104d5d7 Merge 4.8-rc6 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-12 09:15:26 +02:00
Mathias Nyman
bcf42aa60c xhci: fix null pointer dereference in stop command timeout function
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)

the ->primary_hcd will be set to NULL at USB3 hcd removal.

Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.

CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-08 08:39:46 +02:00
Russell King
b68824b1a6 USB: ohci-omap - avoid including mach/irqs.h
ohci-omap doesn't need to include mach/irqs.h - nothing within this
driver needs anything from this header file.  Remove this include.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:31:33 +02:00
Russell King
70efb643a8 usb: ohci-sa1111: remove mach/hardware.h include
The mach/hardware.h include doesn't seem to be necessary to build
ohci-sa1111, so let's remove it to kill off an unnecessary platform
specific include.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:24:59 +02:00
Russell King
6ebb8f0f83 usb: ohci-sa1111: remove machine_has_neponset()
The neponset is a daughter board for the Assabet platform, which has a
SA1111 chip on it.  If we're initialising the SA1111 OHCI, and we're
part of a neponset, the host platform must be an Assabet.

This allows us to eliminate machine_has_neponset() from this driver,
replacing it instead with machine_is_assabet(), and killing the
mach/assabet.h include.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:24:59 +02:00
Wenyou Yang
2e2aa1bc7e usb: ohci-at91: Forcibly suspend ports while USB suspend
The usb controller does not manage correctly the suspend mode for
the ehci. In echi mode, there is no way to suspend without any
device connected to it. This is why this specific control is added
to fix this issue. Since the suspend mode works in ohci mode, this
specific control works by suspend the usb controller in ohci mode.

This specific control is by setting the SUSPEND_A/B/C fields of
SFR_OHCIICR(OHCI Interrupt Configuration Register) in the SFR
while the OHCI USB suspend.

This set operation must be done before the USB clock disabled,
clear operation after the USB clock enabled.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:23:22 +02:00
Wolfram Sang
f4c46f119a usb: host: xhci: don't print on ENOMEM
All kmalloc-based functions print enough information on failures.

Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:17:37 +02:00
Wolfram Sang
a35234b2a6 usb: host: xhci-tegra: don't print on ENOMEM
All kmalloc-based functions print enough information on failures.

Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:17:37 +02:00
Wolfram Sang
314e672506 usb: host: uhci-hcd: don't print on ENOMEM
All kmalloc-based functions print enough information on failures.

Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:17:37 +02:00
Wolfram Sang
13dcf78005 usb: host: max3421-hcd: don't print on ENOMEM
All kmalloc-based functions print enough information on failures.

Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:17:37 +02:00
Wolfram Sang
2652de71c5 usb: host: fhci-hcd: don't print on ENOMEM
All kmalloc-based functions print enough information on failures.

Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-30 19:17:37 +02:00
Greg Kroah-Hartman
1aaaa9acae Merge 4.8-rc3 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-21 21:33:17 -04:00
Mathias Nyman
f1f6d9a8b5 xhci: don't dereference a xhci member after removing xhci
Remove the hcd after checking for the xhci last quirks, not before.

This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device

CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-16 09:42:47 +02:00
Jim Lin
88716a9376 usb: xhci: Fix panic if disconnect
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device

If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.

virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)

[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G     U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4

This issue is found when running with realtek ethernet device
(0bda:8153).

Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-16 09:42:47 +02:00
Alban Browaeys
0d2daaded8 xhci: really enqueue zero length TRBs.
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.

Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-16 09:42:47 +02:00
Mathias Nyman
33be126510 xhci: always handle "Command Ring Stopped" events
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.

The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.

Solve it by handling the command ring stopped event before checking for a
matching command.

In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.

If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-16 09:42:47 +02:00
Icenowy Zheng
73577d6179 ehci-platform: add the max clock number to 4
Allwinner A64 EHCI requires 4 clocks to be enabled.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-15 16:25:59 +02:00
Rafał Miłecki
d6b76c4ddb USB: bcma: support old USB 2.0 controller on Northstar devices
Currently bcma-hcd driver handles 3 different bcma cores:
1) BCMA_CORE_USB20_HOST (0x819)
2) BCMA_CORE_NS_USB20 (0x504)
3) BCMA_CORE_NS_USB30 (0x505)

The first one was introduced years ago and so far was used on MIPS
devices only. All Northstar (ARM) devices were using other two cores
which allowed easy implementation of separated initialization paths.

It seems however Broadcom decided to reuse this old USB 2.0 controller
on some recently introduced cheaper Northstar BCM53573 SoCs. I noticed
this on Tenda AC9 (based on BCM47189B0 belonging to BCM53573 family).

There is no difference in this old controller core identification
between MIPS and ARM devices: they share the same id and revision. We
need different controller initialization procedure however.
To handle this add a check for architecture and implement required
initialization for ARM case.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-15 16:25:59 +02:00
Bhaktipriya Shridhar
d35cbed604 whci: Remove deprecated create_singlethread_workqueue
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.

The workqueue "workqueue" has multiple workitems which may require
ordering. Hence, a dedicated ordered workqueue has been used.
Since the workqueue is not being used on a memory reclaim path,
WQ_MEM_RECLAIM has not been set.

Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-15 16:25:58 +02:00
Jaewon Kim
59b71f774f usb: host: max3421-hcd: fix mask of IO control register
GPIO control register is divided into IOPINS1 and IOPINS2.
And low 4-bit of register is controls output.

So, this patch fixes wrong mask of GPIO output.

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-09 16:14:18 +02:00
Marc Ohlf
bc337b5150 usb: ehci: change order of register cleanup during shutdown
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.

This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.

Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-09 16:14:18 +02:00
Rafał Miłecki
3cc7e7b787 USB: bcma: initialize Northstar USB 3.0 controller
It's a rather simple controller, we just need to make sure USB is
powered (using GPIO pin) and reset bus core. Once this is done it's
safe to register XHCI controller and let it init PHY and do its magic.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-09 15:59:35 +02:00
Julia Lawall
72cd194f89 usb: host: fsl-mph-dr-of: use of_property_read_bool
Use of_property_read_bool to check for the existence of a property.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e1,e2,x;
@@
-	if (of_get_property(e1,e2,NULL))
-		x = true;
-	else
-		x = false;
+	x = of_property_read_bool(e1,e2);
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-09 15:49:01 +02:00
Linus Torvalds
c8d0267efd PCI changes for the v4.8 merge window:
Enumeration
     Move ecam.h to linux/include/pci-ecam.h (Jayachandran C)
     Add parent device field to ECAM struct pci_config_window (Jayachandran C)
     Add generic MCFG table handling (Tomasz Nowicki)
     Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki)
     Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki)
 
   Resource management
     Add devm_request_pci_bus_resources() (Bjorn Helgaas)
     Unify pci_resource_to_user() declarations (Bjorn Helgaas)
     Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas)
     Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas)
     Make PCI I/O space optional on ARM32 (Bjorn Helgaas)
     Ignore write combining when mapping I/O port space (Bjorn Helgaas)
     Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas)
     Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas)
     Support I/O resources when parsing host bridge resources (Jayachandran C)
     Add helpers to request/release memory and I/O regions (Johannes Thumshirn)
     Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn)
     Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5))
     Add generic pci_bus_claim_resources() (Lorenzo Pieralisi)
     Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
     Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi)
     Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya)
     Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu)
 
   PCI device hotplug
     Allow additional bus numbers for hotplug bridges (Keith Busch)
     Ignore interrupts during D3cold (Lukas Wunner)
 
   Power management
     Enforce type casting for pci_power_t (Andy Shevchenko)
     Don't clear d3cold_allowed for PCIe ports (Mika Westerberg)
     Put PCIe ports into D3 during suspend (Mika Westerberg)
     Power on bridges before scanning new devices (Mika Westerberg)
     Runtime resume bridge before rescan (Mika Westerberg)
     Add runtime PM support for PCIe ports (Mika Westerberg)
     Remove redundant check of pcie_set_clkpm (Shawn Lin)
 
   Virtualization
     Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra)
     Add DMA alias quirk for Adaptec 3805 (Alex Williamson)
     Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake)
     Add ACS quirk for Solarflare SFC9220 (Edward Cree)
 
   MSI
     Fix PCI_MSI dependencies (Arnd Bergmann)
     Add pci_msix_desc_addr() helper (Christoph Hellwig)
     Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig)
     Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig)
     Provide sensible IRQ vector alloc/free routines (Christoph Hellwig)
     Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig)
 
   Error Handling
     Bind DPC to Root Ports as well as Downstream Ports (Keith Busch)
     Remove DPC tristate module option (Keith Busch)
     Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg)
 
   Generic host bridge driver
     Select IRQ_DOMAIN (Arnd Bergmann)
     Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
 
   ACPI host bridge driver
     Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki)
     Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki)
     Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki)
     Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki)
 
   Altera host bridge driver
     Check link status before retrain link (Ley Foon Tan)
     Poll for link up status after retraining the link (Ley Foon Tan)
 
   Axis ARTPEC-6 host bridge driver
     Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann)
     Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel)
     Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel)
 
   Intel VMD host bridge driver
     Use lock save/restore in interrupt enable path (Jon Derrick)
     Select device dma ops to override (Keith Busch)
     Initialize list item in IRQ disable (Keith Busch)
     Use x86_vector_domain as parent domain (Keith Busch)
     Separate MSI and MSI-X vector sharing (Keith Busch)
 
   Marvell Aardvark host bridge driver
     Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni)
     Add Aardvark PCI host controller driver (Thomas Petazzoni)
     Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni)
 
   Microsoft Hyper-V host bridge driver
     Fix interrupt cleanup path (Cathy Avery)
     Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
     Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
 
   NVIDIA Tegra host bridge driver
     Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren)
     Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren)
     Use lower-case hex consistently for register definitions (Thierry Reding)
     Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding)
     Stop setting pcibios_min_mem (Thierry Reding)
 
   Renesas R-Car host bridge driver
     Drop gen2 dummy I/O port region (Bjorn Helgaas)
 
   TI DRA7xx host bridge driver
     Fix return value in case of error (Christophe JAILLET)
 
   Xilinx AXI host bridge driver
     Fix return value in case of error (Christophe JAILLET)
 
   Miscellaneous
     Make bus_attr_resource_alignment static (Ben Dooks)
     Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks)
     MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven)
     Make host bridge drivers explicitly non-modular (Paul Gortmaker)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJXoNRtAAoJEFmIoMA60/r8LMkP/3kiNh21QFS6RZGOaDft5/Py
 n14Zo0w51avspxoI3iyDlBd5q/SssMqi+2c6Ko/fh2D2xMxJgmQOjdMDrIGARxGA
 qEHk/5IoXquY2/GcptmCk3ap66cJ6kTovS4OPrb73m3fPuknFwFwdzExq22XHbnI
 crPya6xwQxPLc54VpY/TsgW8E+EKZd/3FW9wuzzNHXrXmTILyhBQzQAA0K470GMx
 wEXU6kc3M/XhRuF1zjV9/O+H/xguwfnbTpZLvd2NAF6uXKZoRytEHHtNnVqu1hoe
 UPpDS2xq32pMNbGxGqBetCdIbkY/hWOufmckHI7Yu2OfXBYyHBYMG2je1+nMPkOV
 WiFhhrchGt5KnEMUwXPS4ROqnSZVpZBl1Fd4s10GhUYkoE2HNKJXta398H9FR1jj
 4NEVSi4mSX/+CkaoIN3lXYiaf9P0wv4Wppve4Scr30+VnLjJhm7Vw5La7v12oo6x
 otrJ/g98AkmnbuUdLeWBUS/+TOcdPjZYbw52rqBsbOOjFm51Zcj6D7kf5WcTypQy
 HzbvygSVabcioWehUG1uudC8pdJmQlUGx1aES/iu+mZEae4cuUFALu6hDBD9IYnZ
 5JdwjVzI0UItEwT3rQt3t4xiAqHADQ0NAVNJVCeREdoy/YQpSoTWGXIpyqCZ1yCm
 aBykjRsxbKQXlhVeIxuc
 =NVxu
 -----END PGP SIGNATURE-----

Merge tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:
 "Highlights:

   - ARM64 support for ACPI host bridges

   - new drivers for Axis ARTPEC-6 and Marvell Aardvark

   - new pci_alloc_irq_vectors() interface for MSI-X, MSI, legacy INTx

   - pci_resource_to_user() cleanup (more to come)

  Detailed summary:

  Enumeration:
   - Move ecam.h to linux/include/pci-ecam.h (Jayachandran C)
   - Add parent device field to ECAM struct pci_config_window (Jayachandran C)
   - Add generic MCFG table handling (Tomasz Nowicki)
   - Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki)
   - Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki)

  Resource management:
   - Add devm_request_pci_bus_resources() (Bjorn Helgaas)
   - Unify pci_resource_to_user() declarations (Bjorn Helgaas)
   - Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas)
   - Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas)
   - Make PCI I/O space optional on ARM32 (Bjorn Helgaas)
   - Ignore write combining when mapping I/O port space (Bjorn Helgaas)
   - Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas)
   - Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas)
   - Support I/O resources when parsing host bridge resources (Jayachandran C)
   - Add helpers to request/release memory and I/O regions (Johannes Thumshirn)
   - Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn)
   - Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5))
   - Add generic pci_bus_claim_resources() (Lorenzo Pieralisi)
   - Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
   - Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi)
   - Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya)
   - Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu)

  PCI device hotplug:
   - Allow additional bus numbers for hotplug bridges (Keith Busch)
   - Ignore interrupts during D3cold (Lukas Wunner)

  Power management:
   - Enforce type casting for pci_power_t (Andy Shevchenko)
   - Don't clear d3cold_allowed for PCIe ports (Mika Westerberg)
   - Put PCIe ports into D3 during suspend (Mika Westerberg)
   - Power on bridges before scanning new devices (Mika Westerberg)
   - Runtime resume bridge before rescan (Mika Westerberg)
   - Add runtime PM support for PCIe ports (Mika Westerberg)
   - Remove redundant check of pcie_set_clkpm (Shawn Lin)

  Virtualization:
   - Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra)
   - Add DMA alias quirk for Adaptec 3805 (Alex Williamson)
   - Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake)
   - Add ACS quirk for Solarflare SFC9220 (Edward Cree)

  MSI:
   - Fix PCI_MSI dependencies (Arnd Bergmann)
   - Add pci_msix_desc_addr() helper (Christoph Hellwig)
   - Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig)
   - Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig)
   - Provide sensible IRQ vector alloc/free routines (Christoph Hellwig)
   - Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig)

  Error Handling:
   - Bind DPC to Root Ports as well as Downstream Ports (Keith Busch)
   - Remove DPC tristate module option (Keith Busch)
   - Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg)

  Generic host bridge driver:
   - Select IRQ_DOMAIN (Arnd Bergmann)
   - Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)

  ACPI host bridge driver:
   - Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki)
   - Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki)
   - Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki)
   - Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki)

  Altera host bridge driver:
   - Check link status before retrain link (Ley Foon Tan)
   - Poll for link up status after retraining the link (Ley Foon Tan)

  Axis ARTPEC-6 host bridge driver:
   - Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann)
   - Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel)
   - Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel)

  Intel VMD host bridge driver:
   - Use lock save/restore in interrupt enable path (Jon Derrick)
   - Select device dma ops to override (Keith Busch)
   - Initialize list item in IRQ disable (Keith Busch)
   - Use x86_vector_domain as parent domain (Keith Busch)
   - Separate MSI and MSI-X vector sharing (Keith Busch)

  Marvell Aardvark host bridge driver:
   - Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni)
   - Add Aardvark PCI host controller driver (Thomas Petazzoni)
   - Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni)

  Microsoft Hyper-V host bridge driver:
   - Fix interrupt cleanup path (Cathy Avery)
   - Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
   - Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov)

  NVIDIA Tegra host bridge driver:
   - Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren)
   - Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren)
   - Use lower-case hex consistently for register definitions (Thierry Reding)
   - Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding)
   - Stop setting pcibios_min_mem (Thierry Reding)

  Renesas R-Car host bridge driver:
   - Drop gen2 dummy I/O port region (Bjorn Helgaas)

  TI DRA7xx host bridge driver:
   - Fix return value in case of error (Christophe JAILLET)

  Xilinx AXI host bridge driver:
   - Fix return value in case of error (Christophe JAILLET)

  Miscellaneous:
   - Make bus_attr_resource_alignment static (Ben Dooks)
   - Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks)
   - MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven)
   - Make host bridge drivers explicitly non-modular (Paul Gortmaker)"

* tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (125 commits)
  PCI: xgene: Make explicitly non-modular
  PCI: thunder-pem: Make explicitly non-modular
  PCI: thunder-ecam: Make explicitly non-modular
  PCI: tegra: Make explicitly non-modular
  PCI: rcar-gen2: Make explicitly non-modular
  PCI: rcar: Make explicitly non-modular
  PCI: mvebu: Make explicitly non-modular
  PCI: layerscape: Make explicitly non-modular
  PCI: keystone: Make explicitly non-modular
  PCI: hisi: Make explicitly non-modular
  PCI: generic: Make explicitly non-modular
  PCI: designware-plat: Make it explicitly non-modular
  PCI: artpec6: Make explicitly non-modular
  PCI: armada8k: Make explicitly non-modular
  PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency
  PCI: Add ACS quirk for Solarflare SFC9220
  arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
  PCI: aardvark: Add Aardvark PCI host controller driver
  dt-bindings: add DT binding for the Aardvark PCIe controller
  PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
  ...
2016-08-02 17:12:29 -04:00
Bjorn Helgaas
9454c23852 Merge branch 'pci/msi-affinity' into next
Conflicts:
	drivers/nvme/host/pci.c
2016-08-01 12:34:01 -05:00
Linus Torvalds
55392c4c06 Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
 "This update provides the following changes:

   - The rework of the timer wheel which addresses the shortcomings of
     the current wheel (cascading, slow search for next expiring timer,
     etc).  That's the first major change of the wheel in almost 20
     years since Finn implemted it.

   - A large overhaul of the clocksource drivers init functions to
     consolidate the Device Tree initialization

   - Some more Y2038 updates

   - A capability fix for timerfd

   - Yet another clock chip driver

   - The usual pile of updates, comment improvements all over the place"

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
  tick/nohz: Optimize nohz idle enter
  clockevents: Make clockevents_subsys static
  clocksource/drivers/time-armada-370-xp: Fix return value check
  timers: Implement optimization for same expiry time in mod_timer()
  timers: Split out index calculation
  timers: Only wake softirq if necessary
  timers: Forward the wheel clock whenever possible
  timers/nohz: Remove pointless tick_nohz_kick_tick() function
  timers: Optimize collect_expired_timers() for NOHZ
  timers: Move __run_timers() function
  timers: Remove set_timer_slack() leftovers
  timers: Switch to a non-cascading wheel
  timers: Reduce the CPU index space to 256k
  timers: Give a few structs and members proper names
  hlist: Add hlist_is_singular_node() helper
  signals: Use hrtimer for sigtimedwait()
  timers: Remove the deprecated mod_timer_pinned() API
  timers, net/ipv4/inet: Initialize connection request timers as pinned
  timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
  timers, drivers/tty/metag_da: Initialize the poll timer as pinned
  ...
2016-07-25 20:43:12 -07:00
Thomas Gleixner
53bf837b78 timers: Remove set_timer_slack() leftovers
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-07-07 10:35:09 +02:00
Greg Kroah-Hartman
c318a821b9 Merge 4.7-rc6 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-07-04 08:19:21 -07:00
Arnd Bergmann
f76a28a69a xhci: free the correct ring
gcc warns about what first looks like a reference to an uninitialized
variable:

drivers/usb/host/xhci-ring.c: In function 'handle_cmd_completion':
drivers/usb/host/xhci-ring.c:753:4: error: 'ep_ring' may be used uninitialized in this function [-Werror=maybe-uninitialized]
    xhci_unmap_td_bounce_buffer(xhci, ep_ring, cur_td);
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-ring.c:647:20: note: 'ep_ring' was declared here
  struct xhci_ring *ep_ring;
                    ^~~~~~~

It's clear to see that the list_empty() check means it can never be
uninitialized, however it still looks wrong:

When ep->cancelled_td_list contains more than one entry, the
ep_ring variable will point to the ring that was retrieved
from the last urb, and we have to look it up again in the
second loop instead, which fixes the behavior and gets rid of the
warning too.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-07-01 08:59:44 -07:00
Linus Torvalds
4aa34ce3c1 - Bug Fixes
- Use new reset_*_get_shared() variant to prevent reset line obtainment failure
     - Fixes: 0b52297 ("reset: Add support for shared reset controls")
   - Fix unintentional switch() fall-through into error path
   - Fix uninitialised variable compiler warning
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXdMAeAAoJEFGvii+H/Hdh2JsQAJ5ez/+WlfVY5enmZTCPTfjv
 YAZOhGuKyK1RcNKVmhRTXKDDlEQtbzX01AG73UOsMuR6Gjfq4q+lsK88ybE6Y3MS
 YuIBa0TXicyywbLhAh4bCqbImFQZ2MhU07mJWn5n6qX1LwrxncKN5MdRj2DKzldv
 s9AG1EKUKf/83k6kuODaP8dXutvWPEGKYKXnq9MQPBliU2j7DT7mfEp3jLGlJvXy
 UkW2uq1RAhu27fe7TKVefatXLIyqo74fi3fuHVZpWfPsoUTFlQd3RzeFL7Q/orWH
 JqiUk55xAbsmtkEeKNbpph1gPyR1pzKKHiNvSfRt/yIjsxOVPGZQZA2y4OpIcOKV
 mbxPUrurhcdI+sK2+7JpcbjKYJpCsGgCXtwbLubLcgler+RatmFWOB8+ayH32eVC
 DELYFtc80YBaDS+2KrgY4la1Mk1agbfDpyhq4Vp5uiRZFhQyldd1XrPPQssMJNc+
 Zme+LRu+EQiullbHDRb6cb0dnV2Tcek4IjI1CsNA6UMAMLcVb8IZ1gX39vWr+BNt
 ZWxxoBOcskPJ/t3h4ddPbuMzSA0ctBkJct9bdjg+bpZeA0aJ46lTQCJk4fZfjViu
 YcDgO8/ZVaDLz5f4f44xJ+Hwnzxr2fezBUirD3UtPvs57BSVnFbHMBXUdy0NCBHk
 mZi1lFOjy7eKuW1+kbrx
 =mo7m
 -----END PGP SIGNATURE-----

Merge tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD fixes from Lee Jones:
 "Contained are some standard fixes and unusually an extension to the
  Reset API.  Some of those changes are required to fix a bug introduced
  in -rc1, which introduces extra 'reset line checks' i.e. whether the
  line is shared or not.  If a line is shared and the new *_shared() API
  is not used, the request fails with an error.  This breaks USB in v4.7
  for ST's platforms.

  Admittedly, there are some patches contained in our (MFD/Reset)
  immutable branch which are not true -fixes, but there isn't anything I
  can do about that.  Rest assured though, there aren't any API
  'changes'.  Everything is the same from the consumer's perspective.

   - Use new reset_*_get_shared() variant to prevent reset line
     obtainment failure (Fixes commit 0b52297f22: "reset: Add support
     for shared reset controls")

   - Fix unintentional switch() fall-through into error path

   - Fix uninitialised variable compiler warning"

* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: da9053: Fix compiler warning message for uninitialised variable
  mfd: max77620: Fix FPS switch statements
  phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
  usb: dwc3: st: Inform the reset framework that our reset line may be shared
  usb: host: ehci-st: Inform the reset framework that our reset line may be shared
  usb: host: ohci-st: Inform the reset framework that our reset line may be shared
  reset: TRIVIAL: Add line break at same place for similar APIs
  reset: Supply *_shared variant calls when using *_optional APIs
  reset: Supply *_shared variant calls when using of_* API
  reset: Ensure drivers are explicit when requesting reset lines
  reset: Reorder inline reset_control_get*() wrappers
2016-06-30 09:44:34 -07:00
Lee Jones
1959930462 usb: host: ehci-st: Inform the reset framework that our reset line may be shared
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP.  New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.

Acked-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-06-30 07:44:21 +01:00
Lee Jones
f5ee3f2b5a usb: host: ohci-st: Inform the reset framework that our reset line may be shared
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP.  New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-06-30 07:44:20 +01:00
Greg Kroah-Hartman
215db94818 usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
 all related drivers.
 
 This time around with 109 non-merge commits mostly
 concentrated on drivers/usb/gadget/udc (41.5%) and
 drivers/usb/dwc3 (28.1%).
 
 There's a big rework on dwc3's transfer handling
 which gave us almost 3x faster USB3 speeds with Mass
 Storage on a particular test scenario I measured. We
 are also removing platform_data from dwc3 after
 converting all users to built-in properties instead.
 
 For the Gadget API, we're just adding tracepoints to
 aid debugging activities.
 
 Other than these, there's the usual set of spelling
 fixes, minor bug fixes and sparse warnings cleanups.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXc7hvAAoJEIaOsuA1yqREgCoP/3/xfIoJfDTLbTG9V898Ma07
 jSHVmaAu4FSktbYv6ndfcdn5tQxpADurc1cphCV1sT24Fdr56YsQdOxagqu892oo
 oW/WMka1bo7OlvzHqZYmy60hAEeWsAaVxqtEtpyb35Q/tH/33bxTlO+MeKmEKpIM
 HVQzMNuzXy6NxytVGu/BnSZRGtDLHZMdaRNEpn465Ll9mP6zm7ebdWnkIGniGRZ+
 YeK1CfvnUcSxmaB83Gr5kthFJUhi5rpX421301FdtkY4cUtZad+FlN0UW3fd8ztC
 hGr2fr+CZO7zVJ/KmEvarTLvYN0ScSjyS0VX9TT/voxJbjqZaIew0mkUWLpdxpYW
 J4i921j5pSVuK9VRbnhObxenLsW66zoqFtHeQ7pRDm3sX2fJGAX5qB6Votw4ziar
 puwE3cQ4Divk6CGEcnUmZ26KvYE/sW7W8WoKAeMMjIinJN46geLjAiqA5dpYxYuH
 ipCe1YdbjpG4GOnTjajZodGUXlmCPbs2VmcgIH36jbQ8S1m1Q3wuO9ClAO8MvGmr
 Y5HzbUeEDyJe4ZKzT9iOWtj0PAa1YEvpSRLwpZaehycQLKvbd0rRDIQ4p+oq7QDK
 gAN+kWCnkNup7qzAD6aE0FrJtYt5u5qVmPfp1H9z8+/AfmG8QZpy2d+VQsAhIwI+
 9d2bok3rsfi87lEFVRWg
 =PT1e
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v4.8 merge window

Here's the big pull request for Peripheral stack and
all related drivers.

This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).

There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.

For the Gadget API, we're just adding tracepoints to
aid debugging activities.

Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
2016-06-29 09:51:48 -07:00
Heikki Krogerus
a3aef37930 xhci: get rid of platform data
No more users for it.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-26 11:43:39 -07:00
Heikki Krogerus
76f9502fe7 xhci: plat: adapt to unified device property interface
Requesting the only property that the driver needs using the
unified device property interface so it will be available
for all types of platforms, not just the ones using DT.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-26 11:43:39 -07:00
Mathias Nyman
d0c77d84b4 xhci: rename and simplify last_trb_on_last_seg() helper
It's only used with rings that have link trbs

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-26 11:43:39 -07:00