The regulator_resolve_supply() function calls set_supply() which in turn
calls create_regulator() to allocate a supply regulator.
If an error occurs after set_supply() succeeded, the allocated regulator
has to be freed before propagating the error code.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator is unregistered with regulator_unregister(), a call to
regulator_put() is made for its input supply if there is one. This does
a module_put() to decrement the refcount of the module that owns the
supply but there isn't a corresponding try_module_get() in set_supply()
to make the calls balanced.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When resolving device supplies if we fail to look up the regulator we
substitute in the dummy supply instead if the system has fully specified
constraints. When resolving supplies for regulators we do not have the
equivalent code and instead just directly use the regulator_dev_lookup()
result causing spurious failures.
This does not affect DT systems since we are able to detect missing
mappings directly as part of regulator_dev_lookup() and so have appropriate
handling in the DT specific code.
Reported-by: Christian Hartmann <cornogle@googlemail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to avoid potential overflows in print_constraints we
better replace sprintf() with scnprintf().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
We weren't taking into account the already used buffer when telling
sprintf() where to print to.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't consider a failure to add the sysfs node as a problem,
so use sysfs_create_link_nowarn() so that we don't print a
backtrace when duplicated files exist. Also, downgrade the printk
message to a debug statement so that we're quiet here. This
allows multiple drivers to request a CPU's regulator so that
CPUfreq and AVSish drivers can coexist.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Voltage regulators can have (unregulated) current limits too, so we should
probably output both voltage and current for all regulators.
Holding the rdev->mutex actually conflicts with _regulator_get_current_limit
but also is not really necessary, as the global regulator_list_mutex already
protects us from the regulator vanishing while we go through the list.
On the rk3288-firefly the summary now looks like:
regulator use open bypass voltage current min max
-------------------------------------------------------------------------------
vcc_sys 0 12 0 5000mV 0mA 5000mV 5000mV
vcc_lan 1 1 0 3300mV 0mA 3300mV 3300mV
ff290000.ethernet 0mV 0mV
vcca_33 0 0 0 3300mV 0mA 3300mV 3300mV
vcca_18 0 0 0 1800mV 0mA 1800mV 1800mV
vdd10_lcd 0 0 0 1000mV 0mA 1000mV 1000mV
[...]
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On modern systems the regulator hierarchy can get quite long and nested
with regulators supplying other regulators. In some cases when debugging
it might be nice to get a tree of these regulators, their consumers
and the regulation constraints in one go.
To achieve this add a regulator_summary sysfs node, similar to
clk_summary in the common clock framework, that walks the regulator
list and creates a tree out of the regulators, their consumers and
core per-regulator settings.
On a rk3288-firefly the regulator_summary would for example look
something like:
regulator use open bypass value min max
-----------------------------------------------------------------------
vcc_sys 0 12 0 5000mV 5000mV 5000mV
vcc_lan 1 1 0 3300mV 3300mV 3300mV
ff290000.ethernet 0mV 0mV
vcca_33 0 0 0 3300mV 3300mV 3300mV
vcca_18 0 0 0 1800mV 1800mV 1800mV
vdd10_lcd 0 0 0 1000mV 1000mV 1000mV
vccio_sd 0 0 0 3300mV 3300mV 3300mV
vcc_20 0 3 0 2000mV 2000mV 2000mV
vcc18_lcd 0 0 0 1800mV 1800mV 1800mV
vcc_18 0 2 0 1800mV 1800mV 1800mV
ff100000.saradc 0mV 0mV
ff0d0000.dwmmc 1650mV 1950mV
vdd_10 0 0 0 1000mV 1000mV 1000mV
vdd_log 0 0 0 1100mV 1100mV 1100mV
vcc_io 0 3 0 3300mV 3300mV 3300mV
ff0f0000.dwmmc 3300mV 3400mV
vcc_flash 1 1 0 1800mV 1800mV 1800mV
ff0f0000.dwmmc 1700mV 1950mV
vcc_sd 1 1 0 3300mV 3300mV 3300mV
ff0c0000.dwmmc 3300mV 3400mV
vcc_ddr 0 0 0 1200mV 1200mV 1200mV
vdd_gpu 0 0 0 1000mV 850mV 1350mV
vdd_cpu 0 1 0 900mV 850mV 1350mV
cpu0 900mV 900mV
vcc_5v 0 2 0 5000mV 5000mV 5000mV
vcc_otg_5v 0 0 0 5000mV 5000mV 5000mV
vcc_host_5v 0 0 0 5000mV 5000mV 5000mV
regulator-dummy 0 0 0 0mV 0mV 0mV
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of resolving regulator supplies during registration move this to
the time of a consumer retrieving a handle. The benefit is that it's
possible for one driver to register regulators with internal
dependencies out of order.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If multiple regulator devices of the same type exist in a system,
the regulator driver assigns generic names for the regulators it
provides, and debugfs is enabled, the regulator subsystem attempts
to create multiple entries with the same name in the regulator debugfs
directory. This fails for all but the first regulator, resulting in
multiple "Failed to create debugfs directory" log entries.
To avoid the problem, prepend the debugfs directory name for a regulator
with its parent device name if available, but only if no explicit
regulator name was provided.
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the regulator_set_optimum_mode() function regulator_set_load() to
better represent what's going on.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Normally _regulator_do_enable() isn't called on an already-enabled
rdev. That's because the main caller, _regulator_enable() always
calls _regulator_is_enabled() and only calls _regulator_do_enable() if
the rdev was not already enabled.
However, there is one caller of _regulator_do_enable() that doesn't
check: regulator_suspend_finish(). While we might want to make
regulator_suspend_finish() behave more like _regulator_enable(), it's
probably also a good idea to make _regulator_do_enable() robust if it
is called on an already enabled rdev.
At the moment, _regulator_do_enable() is _not_ robust for already
enabled rdevs if we're using an ena_pin. Each time
_regulator_do_enable() is called for an rdev using an ena_pin the
reference count of the ena_pin is incremented even if the rdev was
already enabled. This is not as intended because the ena_pin is for
something else: for keeping track of how many active rdevs there are
sharing the same ena_pin.
Here's how the reference counting works here:
* Each time _regulator_enable() is called we increment
rdev->use_count, so _regulator_enable() calls need to be balanced
with _regulator_disable() calls.
* There is no explicit reference counting in _regulator_do_enable()
which is normally just a warapper around rdev->desc->ops->enable()
with code for supporting delays. It's not expected that the
"ops->enable()" call do reference counting.
* Since regulator_ena_gpio_ctrl() does have reference counting
(handling the sharing of the pin amongst multiple rdevs), we
shouldn't call it if the current rdev is already enabled.
Note that as part of this we cleanup (remove) the initting of
ena_gpio_state in regulator_register(). In _regulator_do_enable(),
_regulator_do_disable() and _regulator_is_enabled() is is clear that
ena_gpio_state should be the state of whether this particular rdev has
requested the GPIO be enabled. regulator_register() was initting it
as the actual state of the pin.
Fixes: 967cfb18c0 ("regulator: core: manage enable GPIO list")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The _regulator_do_enable() call ought to be a no-op when called on an
already-enabled regulator. However, as an optimization
_regulator_enable() doesn't call _regulator_do_enable() on an already
enabled regulator. That means we never test the case of calling
_regulator_do_enable() during normal usage and there may be hidden
bugs or warnings. We have seen warnings issued by the tps65090 driver
and bugs when using the GPIO enable pin.
Let's match the same optimization that _regulator_enable() in
regulator_suspend_finish(). That may speed up suspend/resume and also
avoids exposing hidden bugs.
[Use much clearer commit message from Doug Anderson]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The commit [39f802d6b6: 'regulator: Build sysfs entries with static
attribute groups'] converted the sysfs entry creation to static
attribute groups, but this resulted in a regression due to the NULL
check of rdev->constraints. At the point where the device is
registered, rdev->constraints isn't set, so the attributes depending
on it are missing.
We may fix it by shuffling the code order in regulator_register(), but
a quicker fix is to just remove this NULL check. rdev->constraints is
in anyway always set to non-NULL in set_machine_constraints(), thus
the check there is basically superfluous.
Fixes: 39f802d6b6 ('regulator: Build sysfs entries with static attribute groups')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reportded-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose the requested load directly to the regulator implementation for
hardware that does not support the normal enum based set_mode().
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling device_create_file() manually after the device
registration, put all in attribute groups and filter the unwanted ones
via is_visible callback. This not only simplifies the code but also
avoids the possible race between the device registration and sysfs
registration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor drms_uA_update() slightly to allow regulator_set_optimum_mode()
to utilize the same logic instead of duplicating it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update documentation for regulator_register() function after renaming
its argument.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When drivers use simplified DT parsing method (they provide
'regulator_desc.of_match') they still may want to parse custom
properties for some of the regulators. For example some of the
regulators support GPIO enable control.
Add a driver-supplied callback for such case. This way the regulator
core parses common bindings offloading a lot of code from drivers and
still custom properties may be used.
The callback, called for each parsed regulator, may modify the
'regulator_config' initially passed to regulator_register().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Copy the 'regulator_config' structure passed to regulator_register()
function so the driver could safely modify it after parsing init data.
The driver may want to change the config as a result of specific init
data parsed by regulator core (e.g. when core handled parsing device
tree).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator framework maintains a list of consumer regulators
for a regulator device and protects it from concurrent access using
the regulator device's mutex lock.
In the case of regulator_put() the consumer is removed and regulator
device's parameters are updated without holding the regulator device's
mutex. This would lead to a race condition between the regulator_put()
and any function which traverses the consumer list or modifies regulator
device's parameters.
Fix this race condition by holding the regulator device's mutex in case
of regulator_put.
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch initializes regulator_no to -1 to avoid extra subtraction
operation performed every time we register a regulator and avoid negative
regulator no in its name.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After freeing pin from regulator_ena_gpio_free, loop can access
the pin. So this patch fixes not to access pin after freeing.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a PRE_DISABLE notification so that consumers can use a
notifier to run any steps required to prepare for the
regulator being switched off. Since the regulator disable
can fail an abort notification is also added.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some systems have very large numbers of regulators so the constraint
logging done at startup can end up being a very big part of the boot
output which is both verbose and slows things down if the console is
a serial console. Lower to dev_dbg() instead, we may want to provide
a boot parameter to raise this in future but for now people can edit
the source.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Most drivers do not set the ena_gpio field of struct regulator_config
before passing it to the regulator core. This is fine as long as the
gpio identifier that is passed is a positive integer. But the gpio
identifier 0 is also valid. So we are not able to decide wether we got a
real gpio identifier or not based on a 0 in ena_gpio.
To be able to decide if it is a valid gpio that got passed, this patch
adds a ena_gpio_initialized field that should be set if was initialized
with a correct value, either a gpio >= 0 or a negative error number. The
core then checks if ena_gpio or ena_gpio_initialized before handling it
as a gpio. This way we maintain backwards compatibility and fix the
behaviour for gpio number 0.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regulator drivers which support DT all repeat very similar code
to supply a list of known regulator identifiers to be matched with DT,
convert that to platform data which is then matched up with the regulators
as they are registered. This is both fiddly to get right and for devices
which can use the standard helpers to provide their operations is the main
source of code in the driver.
Since this code is essentially identical for most drivers we can factor it
out into the core, moving the identifiers in the match table into the
regulator descriptors and also allowing drivers to pass in the name of the
subnode to search. When a driver provides an of_match string for the
regulator the core will attempt to use that to obtain init_data, allowing
the driver to remove all explicit code for DT parsing and simply provide
data instead.
The current code leaks the phandles for the child nodes, this will be
addressed incrementally and makes no practical difference for FDT anyway
as the DT data structures are never freed.
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases we need to know when a regulator is about to be changed.
Add a way for clients to be notified. Note that for set_voltage() we
don't necessarily know what voltage we'll end up with, so we tell the
client what the range will be so they can prepare.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie+linaro@kernel.org>
