Commit Graph

367 Commits

Author SHA1 Message Date
Krzysztof Oledzki
dd53df265b bonding: add Speed/Duplex information to /proc/net/bonding/bond
Effect:
 Slave Interface: eth5
 MII Status: up
 Speed: 10000 Mbps
 Duplex: full
 Link Failure Count: 0
 Permanent HW addr: XX:XX:XX:XX:XX:XX
 Slave queue ID: 0

Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 18:43:34 -07:00
Krzysztof Piotr Oledzki
546add7946 bonding: reread information about speed and duplex when interface goes up
When an interface was enslaved when it was down, bonding thinks
it has speed -1 even after it goes up. This leads into selecting
a wrong active interface in active/backup mode on mixed 10G/1G or
1G/100M environment.

before:
 bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.

after:
 bonding: bond0: link status definitely up for interface eth5, 10000 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 1000 Mbps full duplex.

Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 14:28:22 -07:00
Krzysztof Piotr Oledzki
700c2a779e bonding: print information about speed and duplex seen by the driver
before:
 bonding: bond0: link status definitely up for interface eth5
 bonding: bond0: link status definitely up for interface eth0

after:
 bonding: bond0: link status definitely up for interface eth5, 100 Mbps full duplex.
 bonding: bond0: link status definitely up for interface eth0, 100 Mbps full duplex.


Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 14:25:06 -07:00
Flavio Leitner
c2952c314b bonding: add retransmit membership reports tunable
Allow sysadmins to configure the number of multicast
membership report sent on a link failure event.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 20:26:58 -07:00
Flavio Leitner
5a37e8ca85 bonding: rejoin multicast groups on VLANs
During a failover, the IGMP membership is sent to update
the switch restoring the traffic, but it misses groups added
to VLAN devices running on top of bonding devices.

This patch changes it to iterate over all VLAN devices
on top of it sending IGMP memberships too.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 20:26:56 -07:00
David S. Miller
e40051d134 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/qlcnic/qlcnic_init.c
	net/ipv4/ip_output.c
2010-09-27 01:03:03 -07:00
Eric Dumazet
807540baae drivers/net: return operator cleanup
Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-26 18:34:29 -07:00
Eric Dumazet
e6599c2ecf bonding: enable gro by default
gro can be enabled by default on bonding devices.

Actual support depends on the lower devices.

One can still use ethtool to switch off GRO if needed.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-17 16:53:24 -07:00
Andy Gospodarek
ab12811c89 bonding: correctly process non-linear skbs
It was recently brought to my attention that 802.3ad mode bonds would no
longer form when using some network hardware after a driver update.
After snooping around I realized that the particular hardware was using
page-based skbs and found that skb->data did not contain a valid LACPDU
as it was not stored there.  That explained the inability to form an
802.3ad-based bond.  For balance-alb mode bonds this was also an issue
as ARPs would not be properly processed.

This patch fixes the issue in my tests and should be applied to 2.6.36
and as far back as anyone cares to add it to stable.

Thanks to Alexander Duyck <alexander.h.duyck@intel.com> and Jesse
Brandeburg <jesse.brandeburg@intel.com> for the suggestions on this one.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: stable@kerne.org
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-14 14:25:32 -07:00
Jiri Bohac
cb32f2a0d1 bonding: Fix jiffies overflow problems (again)
The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).

Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.

jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-07 13:57:20 -07:00
Andy Gospodarek
c5cb002fb0 bonding: prevent sysfs from allowing arp monitoring with alb/tlb
When using module options arp monitoring and balance-alb/balance-tlb
are mutually exclusive options.  Anytime balance-alb/balance-tlb are
enabled mii monitoring is forced to 100ms if not set.  When configuring
via sysfs no checking is currently done.

Handling these cases with sysfs has to be done a bit differently because
we do not have all configuration information available at once.  This
patch will not allow a mode change to balance-alb/balance-tlb if
arp_interval is already non-zero.  It will also not allow the user to
set a non-zero arp_interval value if the mode is already set to
balance-alb/balance-tlb.  They are still mutually exclusive on a
first-come, first serve basis.

Tested with initscripts on Fedora and manual setting via sysfs.

Signed-off-by: Andy Gospodarek <gospo@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-30 23:27:57 -07:00
David S. Miller
bb7e95c8fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bnx2x_main.c

Merge bnx2x bug fixes in by hand... :-/

Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-27 21:01:35 -07:00
Greg Edwards
d8190dff01 bonding: set device in RLB ARP packet handler
After:

commit 6146b1a4da
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Tue Nov 4 17:51:15 2008 -0800

    bonding: Fix ALB mode to balance traffic on VLANs

the dev field in the RLB ARP packet handler was set to NULL to wildcard
and accommodate balancing VLANs on top of bonds.

This has the side-effect of the packet handler being called against
other, non RLB-enabled bonds, and a kernel oops results when it tries to
dereference rx_hashtbl in rlb_update_entry_from_arp(), which won't be
set for those bonds, e.g. active-backup.

With the __netif_receive_skb() changes from:

commit 1f3c8804ac
Author: Andy Gospodarek <andy@greyhouse.net>
Date:   Mon Dec 14 10:48:58 2009 +0000

    bonding: allow arp_ip_targets on separate vlans to use arp validation

frames received on VLANs correctly make their way to the bond's handler,
so we no longer need to wildcard the device.

The oops can be reproduced by:

modprobe bonding

echo active-backup > /sys/class/net/bond0/bonding/mode
echo 100 > /sys/class/net/bond0/bonding/miimon
ifconfig bond0 xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx
echo +eth0 > /sys/class/net/bond0/bonding/slaves
echo +eth1 > /sys/class/net/bond0/bonding/slaves

echo +bond1 > /sys/class/net/bonding_masters
echo balance-alb > /sys/class/net/bond1/bonding/mode
echo 100 > /sys/class/net/bond1/bonding/miimon
ifconfig bond1 xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx
echo +eth2 > /sys/class/net/bond1/bonding/slaves
echo +eth3 > /sys/class/net/bond1/bonding/slaves

Pass some traffic on bond0.  Boom.

[ Tested, behaves as advertised.  I do not believe a test of the bonding
mode is necessary, as there is no race between the packet handler and
the bonding mode changing (the mode can only change when the device is
closed).  Also updated the log message to include the reproduction and
full commit ids.  -J ]

Signed-off-by: Greg Edwards <greg.edwards@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-24 20:37:48 -07:00
Jay Vosburgh
03dc2f4c52 bonding: don't lock when copying/clearing VLAN list on slave
When copying VLAN information to or removing from a slave
during slave addition or removal, the bonding code currently holds
the bond->lock for write to prevent concurrent modification of the
vlan_list / vlgrp.

	This is unnecessary, as all of these operations occur under
RTNL.  Holding the bond->lock also caused might_sleep issues for
some drivers' ndo_vlan_* functions.  This patch removes the extra
locking.

	Problem reported by Michael Chan <mchan@broadcom.com>

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-22 14:14:47 -07:00
Jay Vosburgh
f35188faa0 bonding: change test for presence of VLANs
After commit ad1afb0039
("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
it is now regular practice for a VLAN "add vid" for VLAN 0 to
arrive prior to any VLAN registration or creation of a vlan_group.

	This patch updates the bonding code that tests for the presence
of VLANs configured above bonding.  The new logic tests for bond->vlgrp
to determine if a registration has occured, instead of testing that
bonding's internal vlan_list is empty.

	The old code would panic when vlan_list was not empty, but
vlgrp was still NULL (because only an "add vid" for VLAN 0 had occured).

	Bonding still adds VLAN 0 to its internal list so that 802.1p
frames are handled correctly on transmit when non-VLAN accelerated
slaves are members of the bond.  The test against bond->vlan_list
remains in bond_dev_queue_xmit for this reason.

	Modification to the bond->vlgrp now occurs under lock (in
addition to RTNL), because not all inspections of it occur under RTNL.

	Additionally, because 8021q will never issue a "kill vid" for
VLAN 0, there is now logic in bond_uninit to release any remaining
entries from vlan_list.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Pedro Garcia <pedro.netdev@dondevamos.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-22 14:14:46 -07:00
Eric Dumazet
90e1795b9b bonding: avoid a warning
drivers/net/bonding/bond_main.c:179:12: warning: ‘disable_netpoll’
defined but not used

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-19 13:34:16 -07:00
Eric Dumazet
db5dda9057 bonding: fix bond_inet6addr_event()
After commit ad1afb0039 (vlan_dev: VLAN 0 should be treated
as "no vlan tag" (802.1p packet)),
bond_inet6addr_event() might be called with a NULL bond->vlgrp pointer, and
a non empty bond->vlan_list. vlan_group_get_device() is dereferencing a NULL pointer.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-19 09:34:31 -07:00
Nicolas de Pesloüan
79236680bd bonding: fix a buffer overflow in bonding_show_queue_id.
The test for buffer overflow ensures we have room for 6 more bytes.
sprintf, called with %s:%d, slave->dev->name, slave->queue_id may yield
far more than 6 bytes.

The correct test is res > (PAGE_SIZE - IFNAMSIZ - 6) .

Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-14 18:24:54 -07:00
David S. Miller
597e608a84 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-07-07 15:59:38 -07:00
Eric Dumazet
28172739f0 net: fix 64 bit counters on 32 bit arches
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.

One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().

Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)

Old drivers (only providing get_stats() method) need no changes.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-07 14:58:56 -07:00
Flavio Leitner
42d782ac1b bonding: check if clients MAC addr has changed
When two systems using bonding devices in adaptive load
balancing (ALB) communicates with each other, an endless
ping-pong of ARP replies starts between these two systems.

What happens? In the ALB mode, bonding driver keeps track
of each client connected in a hash table, so it can do the
receive load balancing (RLB). This hash table is updated
when an ARP reply is received, then it scans for the client
entry, updates its MAC address and flag it to be announced
later. Therefore, two seconds later, the alb monitor runs
and send for each updated client entry two ARP replies
updating this specific client. The same process happens on
the receiving system, causing the endless ping-pong of arp
replies.

See more information including the relevant functions below:

   System 1                          System 2
    bond0                             bond0

   ping <system2>
    ARP request  --------->
                           <--------- ARP reply

+->rlb_arp_recv  <---------------------+   <--- loop begins
|  rlb_update_entry_from_arp           |
|  client_info->ntt = 1;               |
|  bond_info->rx_ntt = 1;              |
|                                      |
|         <communication succeed>      |
|                                      |
|  bond_alb_monitor                    |
|  rlb_update_rx_clients               |
|  rlb_update_client                   |
|  arp_create(ARPOP_REPLY)             |
|   send ARP reply -------------->     V
|   send ARP reply -------------->
|                               rlb_arp_recv
|                               rlb_update_entry_from_arp
|                               client_info->ntt = 1;
|                               bond_info->rx_ntt = 1;
|                           < snipped, same as in system 1>
+-------           <-------------- send ARP reply
                   <-------------- send ARP reply

Besides the unneeded networking traffic, this loop breaks
a cluster because a backup system can't take over the IP
address. There is always one system sending an ARP reply
poisoning the network.

This patch fixes the problem adding a check for the MAC
address before updating it. Thus, if the MAC address didn't
change, there is no need to update neither to announce it later.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-30 13:51:11 -07:00
Andy Gospodarek
c22d7ac844 bonding: prevent netpoll over bonded interfaces
Support for netpoll over bonded interfaces was added here:

	commit f6dc31a85c
	Author: WANG Cong <amwang@redhat.com>
	Date:   Thu May 6 00:48:51 2010 -0700

	    bonding: make bonding support netpoll

but it is bad enough that we should probably just disable netpoll over
bonding until some of the locking logic in the bonding driver is changed
or converted completely to RCU.  Simple actions like changing the active
slave in active-backup mode will hang the box if a high enough printk
debugging level is enabled.

Keeping the old code around will be good for anyone that wants to work
on it (and for after the RCU conversion), so I propose this small patch
rather than ripping it all out.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-28 23:54:10 -07:00
Ben Hutchings
be1f3c2c02 net: Enable 64-bit net device statistics on 32-bit architectures
Use struct rtnl_link_stats64 as the statistics structure.

On 32-bit architectures, insert 32 bits of padding after/before each
field of struct net_device_stats to make its layout compatible with
struct rtnl_link_stats64.  Add an anonymous union in net_device; move
stats into the union and add struct rtnl_link_stats64 stats64.

Add net_device_ops::ndo_get_stats64, implementations of which will
return a pointer to struct rtnl_link_stats64.  Drivers that implement
this operation must not update the structure asynchronously.

Change dev_get_stats() to call ndo_get_stats64 if available, and to
return a pointer to struct rtnl_link_stats64.  Change callers of
dev_get_stats() accordingly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-12 15:51:22 -07:00
Changli Gao
d8d1f30b95 net-next: remove useless union keyword
remove useless union keyword in rtable, rt6_info and dn_route.

Since there is only one member in a union, the union keyword isn't useful.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-10 23:31:35 -07:00
Andy Gospodarek
bb1d912323 bonding: allow user-controlled output slave selection
v2: changed bonding module version, modified to apply on top of changes
from previous patch in series, and updated documentation to elaborate on
multiqueue awareness that now exists in bonding driver.

This patch give the user the ability to control the output slave for
round-robin and active-backup bonding.  Similar functionality was
discussed in the past, but Jay Vosburgh indicated he would rather see a
feature like this added to existing modes rather than creating a
completely new mode.  Jay's thoughts as well as Neil's input surrounding
some of the issues with the first implementation pushed us toward a
design that relied on the queue_mapping rather than skb marks.
Round-robin and active-backup modes were chosen as the first users of
this slave selection as they seemed like the most logical choices when
considering a multi-switch environment.

Round-robin mode works without any modification, but active-backup does
require inclusion of the first patch in this series and setting
the 'all_slaves_active' flag.  This will allow reception of unicast traffic on
any of the backup interfaces.

This was tested with IPv4-based filters as well as VLAN-based filters
with good results.

More information as well as a configuration example is available in the
patch to Documentation/networking/bonding.txt.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-05 02:23:17 -07:00
Andy Gospodarek
ebd8e4977a bonding: add all_slaves_active parameter
v2: changed parameter name from 'keep_all' to 'all_slaves_active' and
skipped setting slaves to inactive rather than creating a new flag at
Jay's suggestion.

In an effort to suppress duplicate frames on certain bonding modes
(specifically the modes that do not require additional configuration on
the switch or switches connected to the host), code was added in the
generic receive patch in 2.6.16.  The current behavior works quite well
for most users, but there are some times it would be nice to restore old
functionality and allow all frames to make their way up the stack.

This patch adds support for a new module option and sysfs file called
'all_slaves_active' that will restore pre-2.6.16 functionality if the
user desires.  The default value is '0' and retains existing behavior,
but the user can set it to '1' and allow all frames up if desired.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-05 02:23:17 -07:00
Jiri Pirko
097811bb48 bonding: optimize tlb_get_least_loaded_slave
In the worst case, when the first loop breaks an the end of the slave list,
the slave list is iterated through twice. This patch reduces this
function only to one loop. Also makes it simpler.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 04:16:24 -07:00
Jiri Pirko
5206e24c2c bonding: remove unused original_flags struct slave member
This is stored but never restored. So remove this as it is useless.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 04:16:24 -07:00
Jiri Pirko
c20811a79e bonding: move dev_addr cpy to bond_enslave
Move the code that copies slave's mac address in case that's the first slave into
bond_enslave. Ifenslave app does this also but that's not a problem. This is
something that should be done in bond_enslave, and it shound not matter from
where is it called.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 04:16:23 -07:00
Jiri Pirko
f9f3545e1e bonding: make bonding_store_slaves simpler
This patch makes bonding_store_slaves function nicer and easier to understand.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:42 -07:00
Jiri Pirko
3dd90905e0 bonding: remove redundant checks from bonding_store_slaves V2
(it's actually the same as v1)

Remove checks that duplicates similar checks in bond_enslave.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:42 -07:00
Jiri Pirko
b15ba0fbdc bonding: move slave MTU handling from sysfs V2
V1->V2: corrected res/ret use

For some reason, MTU handling (storing, and restoring) is taking  place in
bond_sysfs. The correct place for this code is in bond_enslave, bond_release.
So move it there.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:41 -07:00
Jiri Pirko
6458590999 bonding: remove unused variable "found"
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 03:39:40 -07:00
WANG Cong
f6dc31a85c bonding: make bonding support netpoll
Based on Andy's work, but I modified a lot.

Similar to the patch for bridge, this patch does:

1) implement the 2 methods to support netpoll for bonding;

2) modify netpoll during forwarding packets via bonding;

3) disable netpoll support of bonding when a netpoll-unabled device
   is added to bonding;

4) enable netpoll support when all underlying devices support netpoll.

Cc: Andy Gospodarek <gospo@redhat.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06 00:48:51 -07:00
David S. Miller
4a35ecf8bf Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bonding/bond_main.c
	drivers/net/via-velocity.c
	drivers/net/wireless/iwlwifi/iwl-agn.c
2010-04-06 23:53:30 -07:00
Jiri Pirko
22bedad3ce net: convert multicast list to list_head
Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:15 -07:00
Jiri Pirko
a748ee2426 net: move address list functions to a separate file
+little renaming of unicast functions to be smooth with multicast ones

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:11 -07:00
Amerigo Wang
9e2e61fbf8 bonding: fix potential deadlock in bond_uninit()
bond_uninit() is invoked with rtnl_lock held, when it does destroy_workqueue()
which will potentially flush all works in this workqueue, if we hold rtnl_lock
again in the work function, it will deadlock.

So move destroy_workqueue() to destructor where rtnl_lock is not held any more,
suggested by Eric.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-01 17:26:01 -07:00
Eric Dumazet
00ae702847 bonding: bond_xmit_roundrobin() fix
Commit a2fd940f (bonding: fix broken multicast with round-robin mode)
added a problem on litle endian machines.

drivers/net/bonding/bond_main.c:4159: warning: comparison is always
false due to limited range of data type

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-31 03:23:56 -07:00
Andy Gospodarek
a2fd940f4c bonding: fix broken multicast with round-robin mode
Round-robin (mode 0) does nothing to ensure that any multicast traffic
originally destined for the host will continue to arrive at the host when
the link that sent the IGMP join or membership report goes down.  One of
the benefits of absolute round-robin transmit.

Keeping track of subscribed multicast groups for each slave did not seem
like a good use of resources, so I decided to simply send on the
curr_active slave of the bond (typically the first enslaved device that
is up).  This makes failover management simple as IGMP membership
reports only need to be sent when the curr_active_slave changes.  I
tested this patch and it appears to work as expected.

Originally reported by Lon Hohberger <lhh@redhat.com>.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Lon Hohberger <lhh@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-27 16:39:15 -07:00
Frans Pop
2381a55c88 net/various: remove trailing space in messages
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-24 14:10:38 -07:00
Jiri Pirko
32a806c194 bonding: flush unicast and multicast lists when changing type
After the type change, addresses in unicast and multicast lists wouldn't make
sense, not to mention possible different lenghts. So flush both lists here.

Note "dev_addr_discard" will be very soon replaced by "dev_mc_flush" (once
mc_list conversion will be done).

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-21 18:31:34 -07:00
stephen hemminger
502a2ffd73 ipv6: convert idev_list to list macros
Convert to list macro's for the list of addresses per interface
in IPv6.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-20 15:45:09 -07:00
Jiri Pirko
3ca5b4042e bonding: check return value of nofitier when changing type
This patch adds the possibility to refuse the bonding type change for
other subsystems (such as for example bridge, vlan, etc.)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-18 20:00:02 -07:00
Jiri Pirko
93d9b7d7a8 net: rename notifier defines for netdev type change
Since generally there could be more netdevices changing type other
than bonding, making this event type name "bonding-unrelated"

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-18 20:00:01 -07:00
Andi Kleen
28812fe11a driver-core: Add attribute argument to class_attribute show/store
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.

Also drivers can extend the attributes with own data fields
and use that in the low level function.

This makes the class attributes the same as sysdev_class attributes
and plain attributes.

This will allow further cleanups in drivers.

Full tree sweep converting all users.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-07 17:04:48 -08:00
Patrick McHardy
8d6184e488 bonding: fix device leak on error in bond_create()
When the register_netdevice() call fails, the newly allocated device is
not freed.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-27 02:52:05 -08:00
Ajit Khaparde
35cfabdc5e bonding: Remove net_device_stats from bonding struct
There is no need to maintain stats in the bonding structure.
Use the instance of net_device_stats in netdevice.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-03 20:32:27 -08:00
David S. Miller
05ba712d7e Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-01-28 06:12:38 -08:00
stephen hemminger
b473946a08 bonding: bond_open error return value
The convention for API functions in kernel is to return errno value;
bond_open would return -1 if alb setup failed. The only reason that
could happen is if kmalloc() failed.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-28 05:55:54 -08:00