Some legacy devices support ony I2C standard mode at 100kHz.
This patch allows to select the standard mode through the DTS
with the use of the existing clock-frequency parameter.
When clock-frequency parameter is not set, the fast mode is selected.
Only when the parameter is set at 100000, the standard mode is selected.
Signed-off-by: Romain Baeriswyl <romainba@abilis.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe
will fail with dmesg:
[ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering
[ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X
[ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot
get CSR clock
[ 2.186503] stmmac_pci_probe: main driver probe failed
[ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering
[ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2
This patch fix the issue by breaking the dependency to devm_clk_get()
as the CSR clock can be obtained at priv->plat->clk_csr from pci driver.
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel has verified there is no peer-to-peer between functions for the below
selection of 82598, 82599, and X520 10G NICs. These NICs lack an ACS
capability, so we're not able to determine this isolation without the help
of quirks.
Generalize the Solarflare quirk and add these Intel 10G NICs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <John.ronciak@intel.com>
This patch adds a new mode of operation to macvlan, called "source".
It allows one to set a list of allowed mac address, which is used
to match against source mac address from received frames on underlying
interface.
This enables creating mac based VLAN associations, instead of standard
port or tag based. The feature is useful to deploy 802.1x mac based
behavior, where drivers of underlying interfaces doesn't allows that.
Configuration is done through the netlink interface using e.g.:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link add link eth0 name macvlan1 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr add 00:22:22:22:22:22
ip link set link dev macvlan0 type macvlan macaddr add 00:33:33:33:33:33
ip link set link dev macvlan1 type macvlan macaddr add 00:33:33:33:33:33
ip link set link dev macvlan1 type macvlan macaddr add 00:44:44:44:44:44
This allows clients with MAC addresses 00:11:11:11:11:11,
00:22:22:22:22:22 to be part of only VLAN associated with macvlan0
interface. Clients with MAC addresses 00:44:44:44:44:44 with only VLAN
associated with macvlan1 interface. And client with MAC address
00:33:33:33:33:33 to be associated with both VLANs.
Based on work of Stefan Gula <steweg@gmail.com>
v8: last version of Stefan Gula for Kernel 3.2.1
v9: rework onto linux-next 2014-03-12 by Michael Braun
add MACADDR_SET command, enable to configure mac for source mode
while creating interface
v10:
- reduce indention level
- rename source_list to source_entry
- use aligned 64bit ether address
- use hash_64 instead of addr[5]
v11:
- rebase for 3.14 / linux-next 20.04.2014
v12
- rebase for linux-next 2014-09-25
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Negated expressions and sub-expressions need to have their flags checked for
TCF_EM_INVERT and their result negated accordingly.
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pci/host-designware:
PCI: designware: Add get_msi_data() to pcie_host_ops
PCI: designware: Rename get_msi_data() to get_msi_addr()
PCI: designware: Fix IO resource end address calculation
PCI: designware: Fix configuration base address when using 'reg'
PCI: designware: Use NULL instead of false
[bhelgaas: Fixup keystone for "PCI: designware: Rename get_msi_data() to
get_msi_addr()"]
In commit 8a29111c7c ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Reported-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
pull request: netfilter/ipvs updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
most relevantly they are:
1) Four patches to make the new nf_tables masquerading support
independent of the x_tables infrastructure. This also resolves a
compilation breakage if the masquerade target is disabled but the
nf_tables masq expression is enabled.
2) ipset updates via Jozsef Kadlecsik. This includes the addition of the
skbinfo extension that allows you to store packet metainformation in the
elements. This can be used to fetch and restore this to the packets through
the iptables SET target, patches from Anton Danilov.
3) Add the hash:mac set type to ipset, from Jozsef Kadlecsick.
4) Add simple weighted fail-over scheduler via Simon Horman. This provides
a fail-over IPVS scheduler (unlike existing load balancing schedulers).
Connections are directed to the appropriate server based solely on
highest weight value and server availability, patch from Kenny Mathis.
5) Support IPv6 real servers in IPv4 virtual-services and vice versa.
Simon Horman informs that the motivation for this is to allow more
flexibility in the choice of IP version offered by both virtual-servers
and real-servers as they no longer need to match: An IPv4 connection
from an end-user may be forwarded to a real-server using IPv6 and
vice versa. No ip_vs_sync support yet though. Patches from Alex Gartrell
and Julian Anastasov.
6) Add global generation ID to the nf_tables ruleset. When dumping from
several different object lists, we need a way to identify that an update
has ocurred so userspace knows that it needs to refresh its lists. This
also includes a new command to obtain the 32-bits generation ID. The
less significant 16-bits of this ID is also exposed through res_id field
in the nfnetlink header to quickly detect the interference and retry when
there is no risk of ID wraparound.
7) Move br_netfilter out of the bridge core. The br_netfilter code is
built in the bridge core by default. This causes problems of different
kind to people that don't want this: Jesper reported performance drop due
to the inconditional hook registration and I remember to have read complains
on netdev from people regarding the unexpected behaviour of our bridging
stack when br_netfilter is enabled (fragmentation handling, layer 3 and
upper inspection). People that still need this should easily undo the
damage by modprobing the new br_netfilter module.
8) Dump the set policy nf_tables that allows set parameterization. So
userspace can keep user-defined preferences when saving the ruleset.
From Arturo Borrero.
9) Use __seq_open_private() helper function to reduce boiler plate code
in x_tables, From Rob Jones.
10) Safer default behaviour in case that you forget to load the protocol
tracker. Daniel Borkmann and Florian Westphal detected that if your
ruleset is stateful, you allow traffic to at least one single SCTP port
and the SCTP protocol tracker is not loaded, then any SCTP traffic may
be pass through unfiltered. After this patch, the connection tracking
classifies SCTP/DCCP/UDPlite/GRE packets as invalid if your kernel has
been compiled with support for these modules.
====================
Trivially resolved conflict in include/linux/skbuff.h, Eric moved some
netfilter skbuff members around, and the netfilter tree adjusted the
ifdef guards for the bridging info pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAICS, prepend_name() is broken on SMP alpha. Disclaimer: I don't have
SMP alpha boxen to reproduce it on. However, it really looks like the race
is real.
CPU1: d_path() on /mnt/ramfs/<255-character>/foo
CPU2: mv /mnt/ramfs/<255-character> /mnt/ramfs/<63-character>
CPU2 does d_alloc(), which allocates an external name, stores the name there
including terminating NUL, does smp_wmb() and stores its address in
dentry->d_name.name. It proceeds to d_add(dentry, NULL) and d_move()
old dentry over to that. ->d_name.name value ends up in that dentry.
In the meanwhile, CPU1 gets to prepend_name() for that dentry. It fetches
->d_name.name and ->d_name.len; the former ends up pointing to new name
(64-byte kmalloc'ed array), the latter - 255 (length of the old name).
Nothing to force the ordering there, and normally that would be OK, since we'd
run into the terminating NUL and stop. Except that it's alpha, and we'd need
a data dependency barrier to guarantee that we see that store of NUL
__d_alloc() has done. In a similar situation dentry_cmp() would survive; it
does explicit smp_read_barrier_depends() after fetching ->d_name.name.
prepend_name() doesn't and it risks walking past the end of kmalloc'ed object
and possibly oops due to taking a page fault in kernel mode.
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Asus T100 internal microphone is not digital but analogue connected to IN1P
pin of the RT564x codec with shared bias between internal and headset
microphones. Because of this there is need to have machine specific DAPM
routes in byt-rt5640.
Add handling for them with the help of DMI quirk that is used to add custom
routes in addition to common. Because "Internal Mic" connected to DMIC1 is
not common to all move it as a default custom route when there is no match
in quirk table.
Custom "Internal Mic" -> "IN1P" with MICBIAS1 route is added for Asus T100.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I tested couple byt-rt5640 based platforms and they have single-ended
headset microphone connection to IN2P only. I guess IN2N was either defined
by accident or some early platform had floating ground for headset. It's
better to remove IN2N and add a custom route for such a platform if needed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When given the number of threads to requeue at once by user input,
there's always the risk of this value being larger than the total number
of threads. This doesn't make any sense, and the kernel can easily deal
with such sort of situations, hence no big deal. We should however
prevent bogus output such as:
./perf bench --repeat 2 futex requeue -q 10
Run summary [PID 22210]: Requeuing 4 threads (from [private] 0x99ef3c to 0x99ef38), 10 at a time.
[Run 1]: Requeued 10 of 4 threads in 0.0040 ms
[Run 2]: Requeued 10 of 4 threads in 0.0030 ms
Requeued 10 of 4 threads in 0.0035 ms (+-14.29%)
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Davidlohr Bueso <dbueso@suse.de>
Link: http://lkml.kernel.org/r/1412008868-22328-2-git-send-email-dave@stgolabs.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Unlike futex-hash, requeuing and wakeup benchmarks do not support shared
futexes, limiting the usefulness of the programs. Correct this, and
allow using the local -S parameter. The default remains using private
futexes.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Davidlohr Bueso <dbueso@suse.de>
Link: http://lkml.kernel.org/r/1412008868-22328-1-git-send-email-dave@stgolabs.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Suggested by Stephen. Also drop inline keyword and let compiler decide.
gcc 4.7.3 decides to no longer inline tcp_ecn_check_ce, so split it up.
The actual evaluation is not inlined anymore while the ECN_OK test is.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Octavian Purdilas tcp ipv4/ipv6 unification work this helper only
has a single callsite.
While at it, convert name to lowercase, suggested by Stephen.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Grzeschik says:
====================
ARCNET: add support for EAE multi interfac card
this series adds support for the PLX Bridge based multi interface
pci cards and adds support to change device address on com200xx chips
during runtime.
This series is based on v3.17-rc7.
It is fixed for build against com20020_cs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the EAE arcnet cards
which has two Interfaces.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The com20020-pci driver is currently designed to instance
one netdev with one pci device. This patch adds support to
instance many cards with one pci device, depending on the device
data in the private data.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds metadata for the com20020 to prepare for devices with
multiple io address areas with multi card interfaces.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds com20020_set_hwaddr to make
it possible to change the hwaddr on runtime.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler needs to return IRQ_NONE in case
two devices are used with the shared interrupt handler.
Otherwise it could steal interrupts from the other
interface.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds server support for the NFS v4.2 operation SEEK, which
returns the position of the next hole or data segment in a file.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It's cleaner to introduce everything at once and have the server reply
with "not supported" than it would be to introduce extra operations when
implementing a specific one in the middle of the list.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Svcrdma currently advertises 1MB, which is too large. The correct value
is the minimum of RPCSVC_MAXPAYLOAD and the max scatter-gather allowed
in an NFSRDMA IO chunk * the host page size. This bug is usually benign
because the Linux X64 NFSRDMA client correctly limits the payload size to
the correct value (64*4096 = 256KB). But if the Linux client is PPC64
with a 64KB page size, then the client will indeed use a payload size
that will overflow the server.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Using 'perf trace' for mmap is truncating return values by stripping the
top 32 bits, actually printing only the lower 32 bits.
This was because the ret value was of an 'int' type and not a 'long'
type.
The Problem:
991258501.244 ( 0.004 ms): mmap(len: 40001536, prot: READ|WRITE, flags: PRIVATE|ANONYMOUS, fd: -1) = 0x56691000
991258501.257 ( 0.000 ms): minfault [_int_malloc+0x1038] => //anon@0x7fa056691008 //(d.)
The first line shows an mmap, which succeeds and returns 0x56691000.
However the next line shows a memory access to that virtual memory area,
specifically to 0x7fa056691008. The upper 32 bit is lost due to the
problem mentioned above, and thus mmap's return value didn't have the
upper 0x7fa0.
Tested on 3.17-rc5 from the linus's tree, and the HEAD of tip/master
Signed-off-by: Chang Hyun Park <heartinpiece@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1411736041-8017-1-git-send-email-heartinpiece@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Passing pointers to alias modifiers 'unit' and 'scale' isn't very
future-proof since if we add more modifiers to the list we'll end up
passing more arguments.
Instead wrap everything up in a struct perf_pmu_info, which can easily
be expanded when additional alias modifiers are necessary in the future.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1411567455-31264-3-git-send-email-matt@console-pimps.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The only remaining user of the CODEC pointer in the DAPM struct is to
initialize the CODEC pointer in the widget struct. The later is scheduled
for removal, but has still a few users left. For now use
dapm->component->codec to initialize it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CODEC struct in the snd_soc_dapm_context struct is deprecated and
scheduled for removal. Use the snd_soc_dapm_to_codec() function instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CODEC struct in the snd_soc_dapm_context struct is deprecated and
scheduled for removal. Use the snd_soc_dapm_to_codec() function instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro "REGMAP_ALLOW_WRITE_DEBUGFS" can be used to enable write
support on the registers file in the debugfs. The mode of the file is
fixed to 0400 so it is not possible to write the file ever.
This patch fixes the mode by setting it to the correct value depending
on the macro.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sort all the include headers alphabetically for the freescale
spi drivers. If the inlcude headers sorted out of order, maybe
the best logical choice is to append new ones after the exist
ones, while this may create a lot of potential for duplicates
and conflicts for each diffenent changes will add new headers
in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The for loop in this function increments two variables and has an unusual
starting index of 1 (not 0). Make it look more familiar.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many of the functions and variables in the driver have been renamed and are now
more understandable, as well as defines added for various constants. Update /
remove some comments to reflect this.
Also many comments were unnecessary dialogue describing what is evident
from the code, or comments were just plain incorrect. Remove these too.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function should have been exported with EXPORT_SYMBOL_GPL()
as part of commit 92d18a6851 ("drivers/vfio: Fix EEH build error").
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This variable i is overwritten to 0 by following code
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With proliferation of bit fields in sk_buff, __copy_skb_header() became
quite expensive, showing as the most expensive function in a GSO
workload.
__copy_skb_header() performance is also critical for non GSO TCP
operations, as it is used from skb_clone()
This patch carefully moves all the fields that were not copied in a
separate zone : cloned, nohdr, fclone, peeked, head_frag, xmit_more
Then I moved all other fields and all other copied fields in a section
delimited by headers_start[0]/headers_end[0] section so that we
can use a single memcpy() call, inlined by compiler using long
word load/stores.
I also tried to make all copies in the natural orders of sk_buff,
to help hardware prefetching.
I made sure sk_buff size did not change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSIx vector table lives in device memory, which may be cleared as
part of a backdoor device reset. This is the case on the IBM IPR HBA
when the BIST is run on the device. When assigned to a QEMU guest,
the guest driver does a pci_save_state(), issues a BIST, then does a
pci_restore_state(). The BIST clears the MSIx vector table, but due
to the way interrupts are configured the pci_restore_state() does not
restore the vector table as expected. Eventually this results in an
EEH error on Power platforms when the device attempts to signal an
interrupt with the zero'd table entry.
Fix the problem by restoring the host cached MSI message prior to
enabling each vector.
Reported-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The patch exports 2 MSI message relevant functions, which will be
used by VFIO PCI driver. The VFIO PCI driver would be built as
a module.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
It is possible to configure a kernel with SND_DAVINCI_SOC=m and
SND_DM365_VOICE_CODEC=y, which results in a link error:
sound/built-in.o: In function `davinci_vcif_probe':
sound/soc/davinci/davinci-vcif.c:223: undefined reference to `davinci_soc_platform_register'
The best way to avoid this is to make SND_DM365_VOICE_CODEC
a tristate option that depends on SND_DAVINCI_SOC, so it
can only be a module or disabled when the base driver is
a loadable module
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
VFIO allows devices to be safely handed off to userspace by putting
them behind an IOMMU configured to ensure DMA and interrupt isolation.
This enables userspace KVM clients, such as kvmtool and qemu, to further
map the device into a virtual machine.
With IOMMUs such as the ARM SMMU, it is then possible to provide SMMU
translation services to the guest operating system, which are nested
with the existing translation installed by VFIO. However, enabling this
feature means that the IOMMU driver must be informed that the VFIO domain
is being created for the purposes of nested translation.
This patch adds a new IOMMU type (VFIO_TYPE1_NESTING_IOMMU) to the VFIO
type-1 driver. The new IOMMU type acts identically to the
VFIO_TYPE1v2_IOMMU type, but additionally sets the DOMAIN_ATTR_NESTING
attribute on its IOMMU domains.
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Some IOMMUs, such as the ARM SMMU, support two stages of translation.
The idea behind such a scheme is to allow a guest operating system to
use the IOMMU for DMA mappings in the first stage of translation, with
the hypervisor then installing mappings in the second stage to provide
isolation of the DMA to the physical range assigned to that virtual
machine.
In order to allow IOMMU domains to be used for second-stage translation,
this patch adds a new iommu_attr (IOMMU_ATTR_NESTING) for setting
second-stage domains prior to device attach. The attribute can also be
queried to see if a domain is actually making use of nesting.
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
