The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.
This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series
in order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform,
but related to the other patches in this set and needed as a bug
fix for at least one board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUYgmgWCrR//JCVInAQIp6A//cb87A7biCHo0hd64v7RtX2dIvYTc8ZDh
7O9yH7NuAtbSI7FF7cVQGGK6nCRqmwO2SM/KLFgbt2MF36FLgQKKZhJIDM/qB4jb
3DCHHH814eqExf4MFfZL4Yxl4FaMqxzSwYX8fD28GmpeVxLeHjh0yQCKmPejz5MW
WgkMcBJS3IPqbhhKMcMZmXteLrEzEm43Uj6dxkZP7RbinyuWzHvx3IWWv4gQ6ITz
3jcCvZC5JWBo9MEPH43vlmOd8qsAn0OvkbtbYiy2Tre5VerqOgbEEXU2U0A2zUSj
YTmRvwIGsIylL2EkVsJTkMj8KJ8TAHZjHyNUY8m2UzWuS+9EdZjf6rXeKIdUz9Wa
0dmiWJEOEvejk0RnHEJm7anmKp7a9YHFkFSRnHbLOAXAMkUZWWcVAMZ4UbDK8RtF
RX6R+ga9tR8R7aBLIzqYyfSHaZ7xUpF6nSBOM4GNVNKtViJv3PENWVQrm2GHcQ9w
+4IMUqXO/5IRvuHW93l+oN8tENDTF0cR0+S7t0R6Vuuh7OebRt9TAE421Hrvt+7p
gI5tvhEeV3o1CMmXWod8X1jxY/1OrONG7wX/x07ymiRnXSd+sZ0CPkYyWultKNw8
bCAsnOP2aFpO1RB0XEC5y8FZ5uSfcQ7Ngu2kyAP7mEXV6qbSHgmb+lyxf2G8ftL2
Rn0M7nbLcz4=
=FY7+
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM Exynos multiplatform changes from Arnd Bergmann:
"These continue the multiplatform support for exynos, adding support
for building most of the essential drivers (clocksource, clk, irqchip)
when combined with other platforms. As a result, it should become
really easy to add full multiplatform exynos support in 3.11, although
we don't yet enable it for 3.10.
The changes were not included in the earlier multiplatform series in
order to avoid clashes with the other Exynos updates.
This also includes work from Tomasz Figa to fix the pwm clocksource
code on Exynos, which is not strictly required for multiplatform, but
related to the other patches in this set and needed as a bug fix for
at least one board."
* tag 'multiplatform-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: dts: exynops4210: really add universal_c210 dts
ARM: dts: exynos4210: Add basic dts file for universal_c210 board
ARM: dts: exynos4: Add node for PWM device
ARM: SAMSUNG: Do not register legacy timer interrupts on Exynos
clocksource: samsung_pwm_timer: Work around rounding errors in clockevents core
clocksource: samsung_pwm_timer: Correct programming of clock events
clocksource: samsung_pwm_timer: Use proper clockevents max_delta
clocksource: samsung_pwm_timer: Add support for non-DT platforms
clocksource: samsung_pwm_timer: Drop unused samsung_pwm struct
clocksource: samsung_pwm_timer: Keep all driver data in a structure
clocksource: samsung_pwm_timer: Make PWM spinlock global
clocksource: samsung_pwm_timer: Let platforms select the driver
Documentation: Add device tree bindings for Samsung PWM timers
clocksource: add samsung pwm timer driver
irqchip: exynos: look up irq using irq_find_mapping
irqchip: exynos: pass irq_base from platform
irqchip: exynos: localize irq lookup for ATAGS
irqchip: exynos: allocate combiner_data dynamically
irqchip: exynos: pass max combiner number to combiner_init
ARM: exynos: add missing properties for combiner IRQs
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUYgjh2CrR//JCVInAQJTvRAAmxaeoI+kQ/pbbRDa/Mnhf+bUmQjvJvx4
uFGYAAi23Txem2Bx6xrfvOo9//ATYSfRxenoSSOtXQucsnrqD0+837Sj2NbO6AB9
MSiFDK4usJtGwSUybkSHNLb2QPBr8XTgmyWVE/sHEw2UtrIToC1n3sxFofFm0guT
ReILKsgK0Wjyq5RntnjWOCHNNp6OGqDGvFXlSJqNA7Z6gR/VZy4o0oXS4Sv3TWgF
zG7ngSG7/u9FP1IQnMr/SxY1T4QS/bBbAC1YvD/7X30DPHrWKR3/3LfLcsc9TUN2
smTlZQjHdgBbGfVPL7JN0fQwA82HEjNSZKLJ0w9uFjxXgnoKT3znpUpQeuf3dsWm
BhEFqN1Rf446S4ft2btBSB2nhX4NTlJ7w6z2F65xgaylgYFsGFTYcpjiOurKe3wF
gGsw31DZdcuI4/LjiWbNGRKbMd7HFFLbFDMJ16TFbNcNr+pM3qpoQ6z3uMbfCBSe
xFnYr+ESN8F2HXMNLiz3CTqLY+Fi/bHd22n3KuI9qsWws/0KDUrTvFh9Sm3kYji5
QwwLl6PRoeFw8H29e3KrPsKoY/BGYAvrAetnC1o79cDFPLwUyii/1B6WwzC4ynfs
K1VhwdVOwnp0sS/a2Pv8sZBpDNI07gwT9P20aiholxgREq2RKNXXVxGGFfK5Qvm9
FG4Vp6EKEQ0=
=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This series from Tomasz Figa restores support for the pwm clocksource
in Exynos, which was broken during the conversion of the platform
to the common clk framework. The clocksource is only used in one
board in the mainline kernel (universal_c210), and this makes it
work for DT based probing as well as restoring the non-DT based
case.
* exynos/pwm-clocksource:
ARM: dts: exynops4210: really add universal_c210 dts
ARM: dts: exynos4210: Add basic dts file for universal_c210 board
ARM: dts: exynos4: Add node for PWM device
ARM: SAMSUNG: Do not register legacy timer interrupts on Exynos
clocksource: samsung_pwm_timer: Work around rounding errors in clockevents core
clocksource: samsung_pwm_timer: Correct programming of clock events
clocksource: samsung_pwm_timer: Use proper clockevents max_delta
clocksource: samsung_pwm_timer: Add support for non-DT platforms
clocksource: samsung_pwm_timer: Drop unused samsung_pwm struct
clocksource: samsung_pwm_timer: Keep all driver data in a structure
clocksource: samsung_pwm_timer: Make PWM spinlock global
clocksource: samsung_pwm_timer: Let platforms select the driver
Documentation: Add device tree bindings for Samsung PWM timers
clocksource: add samsung pwm timer driver
Conflicts:
arch/arm/boot/dts/Makefile
arch/arm/mach-exynos/common.c
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here, which
would extend support for the existing generic "psci" call that is used
on multiple platforms as well as Xen and KVM guests, but that ended up
getting dropped because the patches were not ready in time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=68m5
-----END PGP SIGNATURE-----
Merge tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM platform specific firmware interfaces from Olof Johansson:
"Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here,
which would extend support for the existing generic "psci" call that
is used on multiple platforms as well as Xen and KVM guests, but that
ended up getting dropped because the patches were not ready in time."
* tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm: mark bcm_kona_smc_init as __init
ARM: bcm281xx: Add DT support for SMC handler
ARM: bcm281xx: Add L2 cache enable code
ARM: EXYNOS: Add secure firmware support to secondary CPU bring-up
ARM: EXYNOS: Add IO mapping for non-secure SYSRAM.
ARM: EXYNOS: Add support for Exynos secure firmware
ARM: EXYNOS: Add support for secure monitor calls
ARM: Add interface for registering and calling firmware-specific operations
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
Pull ARM updates from Russell King:
"The major items included in here are:
- MCPM, multi-cluster power management, part of the infrastructure
required for ARMs big.LITTLE support.
- A rework of the ARM KVM code to allow re-use by ARM64.
- Error handling cleanups of the IS_ERR_OR_NULL() madness and fixes
of that stuff for arch/arm
- Preparatory patches for Cortex-M3 support from Uwe Kleine-König.
There is also a set of three patches in here from Hugh/Catalin to
address freeing of inappropriate page tables on LPAE. You already
have these from akpm, but they were already part of my tree at the
time he sent them, so unfortunately they'll end up with duplicate
commits"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: EXYNOS: remove unnecessary use of IS_ERR_VALUE()
ARM: IMX: remove unnecessary use of IS_ERR_VALUE()
ARM: OMAP: use consistent error checking
ARM: cleanup: OMAP hwmod error checking
ARM: 7709/1: mcpm: Add explicit AFLAGS to support v6/v7 multiplatform kernels
ARM: 7700/2: Make cpu_init() notrace
ARM: 7702/1: Set the page table freeing ceiling to TASK_SIZE
ARM: 7701/1: mm: Allow arch code to control the user page table ceiling
ARM: 7703/1: Disable preemption in broadcast_tlb*_a15_erratum()
ARM: mcpm: provide an interface to set the SMP ops at run time
ARM: mcpm: generic SMP secondary bringup and hotplug support
ARM: mcpm_head.S: vlock-based first man election
ARM: mcpm: Add baremetal voting mutexes
ARM: mcpm: introduce helpers for platform coherency exit/setup
ARM: mcpm: introduce the CPU/cluster power API
ARM: multi-cluster PM: secondary kernel entry code
ARM: cacheflush: add synchronization helpers for mixed cache state accesses
ARM: cpu hotplug: remove majority of cache flushing from platforms
ARM: smp: flush L1 cache in cpu_die()
ARM: tegra: remove tegra specific cpu_disable()
...
s5p_register_gpio_interrupt() returns 0 or positive for success, and
-ve for errors, so just use the standard >= 0 test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
More multiplatform enablement for ARM platforms. The ones converted in
this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was a
patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4hSo
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform updates from Olof Johansson:
"More multiplatform enablement for ARM platforms. The ones converted
in this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was
a patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then"
* tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms
clocksource: nomadik-mtu: fix up clocksource/timer
Revert "ARM: exynos: enable multiplatform support"
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: exynos: enable multiplatform support
rtc: s3c: make header file local
mtd: onenand/samsung: make regs-onenand.h file local
thermal/exynos: remove unnecessary header inclusions
mmc: sdhci-s3c: remove platform dependencies
ARM: samsung: move mfc device definition to s5p-dev-mfc.c
ARM: exynos: move debug-macro.S to include/debug/
ARM: exynos: prepare for sparse IRQ
ARM: exynos: introduce EXYNOS_ATAGS symbol
ARM: tegra: build assembly files with -march=armv7-a
ARM: Push selects for TWD/SCU into machine entries
ARM: ux500: build hotplug.o for ARMv7-a
ARM: ux500: move to multiplatform
ARM: ux500: make remaining headers local
ARM: ux500: make irqs.h local to platform
ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
...
This branch contains platform updates for 3.10. Among the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HXX3
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"This branch contains part 1 of the platform updates for 3.10. Among
the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (135 commits)
ARM: tegra: pm: fix build error w/o PM_SLEEP
ARM: davinci: ensure global variables are declared
ARM: davinci: sram.c: fix incorrect type in assignment
ARM: davinci: da8xx dt: make file local symbols static
ARM: davinci: da8xx: add remoteproc support
ARM: socfpga: Upgrade clk driver for socfpga to make use of dts clock entries
ARM: socfpga: Add clock entries into device tree
ARM: socfpga: Enable soft reset
ARM: EXYNOS: replace cpumask by the corresponding macro
ARM: EXYNOS: handle properly the return values
ARM: EXYNOS: factor out the idle states
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
ARM: tegra: pm: remove duplicated include from pm.c
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: SAMSUNG: check processor type before cache restoration in resume
...
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
- ARM big.LITTLE cpufreq driver from Viresh Kumar.
- exynos5440 cpufreq driver from Amit Daniel Kachhap.
- cpufreq core cleanup and code consolidation from Viresh Kumar and
Stratos Karafotis.
- cpufreq scalability improvement from Nathan Zimmer.
- AMD "frequency sensitivity feedback" powersave bias for the ondemand
cpufreq governor from Jacob Shin.
- cpuidle code consolidation and cleanups from Daniel Lezcano.
- ARM OMAP cpuidle fixes from Santosh Shilimkar and Daniel Lezcano.
- ACPICA fixes and other improvements from Bob Moore, Jung-uk Kim,
Lv Zheng, Yinghai Lu, Tang Chen, Colin Ian King, and Linn Crosetto.
- ACPI core updates related to hotplug from Toshi Kani, Paul Bolle,
Yasuaki Ishimatsu, and Rafael J. Wysocki.
- Intel Lynxpoint LPSS (Low-Power Subsystem) support improvements
from Rafael J. Wysocki and Andy Shevchenko.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=H/se
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael J Wysocki:
- ARM big.LITTLE cpufreq driver from Viresh Kumar.
- exynos5440 cpufreq driver from Amit Daniel Kachhap.
- cpufreq core cleanup and code consolidation from Viresh Kumar and
Stratos Karafotis.
- cpufreq scalability improvement from Nathan Zimmer.
- AMD "frequency sensitivity feedback" powersave bias for the ondemand
cpufreq governor from Jacob Shin.
- cpuidle code consolidation and cleanups from Daniel Lezcano.
- ARM OMAP cpuidle fixes from Santosh Shilimkar and Daniel Lezcano.
- ACPICA fixes and other improvements from Bob Moore, Jung-uk Kim, Lv
Zheng, Yinghai Lu, Tang Chen, Colin Ian King, and Linn Crosetto.
- ACPI core updates related to hotplug from Toshi Kani, Paul Bolle,
Yasuaki Ishimatsu, and Rafael J Wysocki.
- Intel Lynxpoint LPSS (Low-Power Subsystem) support improvements from
Rafael J Wysocki and Andy Shevchenko.
* tag 'pm+acpi-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (192 commits)
cpufreq: Revert incorrect commit 5800043
cpufreq: MAINTAINERS: Add co-maintainer
cpuidle: add maintainer entry
ACPI / thermal: do not always return THERMAL_TREND_RAISING for active trip points
ARM: s3c64xx: cpuidle: use init/exit common routine
cpufreq: pxa2xx: initialize variables
ACPI: video: correct acpi_video_bus_add error processing
SH: cpuidle: use init/exit common routine
ARM: S5pv210: compiling issue, ARM_S5PV210_CPUFREQ needs CONFIG_CPU_FREQ_TABLE=y
ACPI: Fix wrong parameter passed to memblock_reserve
cpuidle: fix comment format
pnp: use %*phC to dump small buffers
isapnp: remove debug leftovers
ARM: imx: cpuidle: use init/exit common routine
ARM: davinci: cpuidle: use init/exit common routine
ARM: kirkwood: cpuidle: use init/exit common routine
ARM: calxeda: cpuidle: use init/exit common routine
ARM: tegra: cpuidle: use init/exit common routine for tegra3
ARM: tegra: cpuidle: use init/exit common routine for tegra2
ARM: OMAP4: cpuidle: use init/exit common routine
...
The diffstat and changelog here is dominated by Lee Jones' heroic
efforts to sync the ab8500 driver that's been maintained out of tree
with mainline (plus Axel's cleanup work on the results) but there's a
few other things here:
- Axel Lin added regulator_map_voltage_ascend() optimising a common
pattern for drivers using the core code.
- Milo Kim tought the regulator core to handle regulators sharing an
enable GPIO, avoiding the need to do hacks to support such systems.
- Andrew Bresticker added code to handle missing supplies for regulators
more sensibly for device tree systems, reducing the need for stubbing
there.
plus the usual batch of driver specific updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rX43
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The diffstat and changelog here is dominated by Lee Jones' heroic
efforts to sync the ab8500 driver that's been maintained out of tree
with mainline (plus Axel's cleanup work on the results) but there's a
few other things here:
- Axel Lin added regulator_map_voltage_ascend() optimising a common
pattern for drivers using the core code.
- Milo Kim tought the regulator core to handle regulators sharing an
enable GPIO, avoiding the need to do hacks to support such systems.
- Andrew Bresticker added code to handle missing supplies for
regulators more sensibly for device tree systems, reducing the need
for stubbing there.
plus the usual batch of driver specific updates and fixes"
* tag 'regulator-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (152 commits)
regulator: mc13892: Fix MC13892_SWITCHERS0_SWxHI bit in set_voltage_sel
regulator: Remove NULL test before calling regulator_unregister()
regulator: mc13783: Add device tree probe support
regulator: mc13xxx: Add warning of incorrect names of regulators
regulator: max77686: Don't update max77686->opmode if update register fails
regulator: max8952: Add missing config.of_node setting for regulator register
regulator: ab3100: Fix regulator register error handling
regulator: tps6524x: Use regulator_map_voltage_ascend
regulator: lp8788-buck: Use regulator_map_voltage_ascend
regulator: lp872x: Use regulator_map_voltage_ascend
regulator: mc13892: Use regulator_map_voltage_ascend for mc13892_sw_regulator_ops
regulator: tps65023: Use regulator_map_voltage_ascend
regulator: tps65023: Merge tps65020 ldo1 and ldo2 vsel table
regulator: tps6507x: Use regulator_map_voltage_ascend
regulator: mc13892: Fix MC13892_SWITCHERS0_SWxHI bit in set_voltage_sel
regulator: ab3100: device tree support
regulator: ab3100: refactor probe to use IDs
regulator: max8973: Don't override control1 variable when set ramp delay bits
regulator: tps80031: Convert tps80031_dcdc_ops to [get|set]_voltage_sel_regmap
regulator: tps80031: Fix LDO2 track mode for TPS80031 or TPS80032-ES1.0
...
Merge in the gic cleanup since it has a handful of annoying internal conflicts
with soc development branches. All of them are delete/delete conflicts.
* gic/cleanup:
irqchip: vic: add include of linux/irq.h
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-shmobile/smp-emev2.c
arch/arm/mach-shmobile/smp-r8a7779.c
arch/arm/mach-shmobile/smp-sh73a0.c
arch/arm/mach-socfpga/platsmp.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sRUG
-----END PGP SIGNATURE-----
Merge tag 'late-exynos-v3-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into late/dt
From Kukjin Kim:
This allows that device tree enables platform to setup a runtime IO
mapping for the chip id
* tag 'late-exynos-v3-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch removes legacy PWM timer interrupt initialization from
exynos{4,5}_init_irq() functions, since it conflicts with internal
interrupt handling of the new PWM clocksource driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* exynos/dt: (125 commits)
ARM: dts: add PDMA0 changes for exynos5440
ARM: dts: Add cpufreq controller node for Exynos5440 SoC
ARM: dts: Fix gmac clock ids due to changes in Exynos5440
ARM: dts: add device tree file for SD5v1 board
ARM: dts: update bootargs to boot from sda2 for exynos5440-ssdk5440
ARM: dts: add PMU support in exynos5440
ARM: dts: Add node for GMAC for exynos5440
ARM: dts: list the interrupts generated by pin-controller on Exynos5440
ARM: dts: Add FIMD DT binding Documentation
ARM: dts: Add FIMD node and display timing node to exynos4412-origen.dts
ARM: dts: Add FIMD node to exynos4
ARM: dts: Add SYSREG block node for S5P/Exynos4 SoC series
ARM: dts: Add display timing node to exynos5250-smdk5250.dts
ARM: dts: Add FIMD node to exynos5
ARM: dts: Add virtual GIC DT bindings for exynos5440
ARM: dts: Document usb clocks in samsung,exynos4210-ehci/ohci bindings
ARM: dts: add usb 2.0 clock references to exynos5250 device tree
ARM: dts: Add architected timer nodes for exynos5250
ARM: dts: Declare the gic as a15 compatible for exynos5250
ARM: dts: Add HDMI HPD and regulator node for Arndale board
...
* pm-cpufreq: (57 commits)
cpufreq: MAINTAINERS: Add co-maintainer
cpufreq: pxa2xx: initialize variables
ARM: S5pv210: compiling issue, ARM_S5PV210_CPUFREQ needs CONFIG_CPU_FREQ_TABLE=y
cpufreq: cpu0: Put cpu parent node after using it
cpufreq: ARM big LITTLE: Adapt to latest cpufreq updates
cpufreq: ARM big LITTLE: put DT nodes after using them
cpufreq: Don't call __cpufreq_governor() for drivers without target()
cpufreq: exynos5440: Protect OPP search calls with RCU lock
cpufreq: dbx500: Round to closest available freq
cpufreq: Call __cpufreq_governor() with correct policy->cpus mask
cpufreq / intel_pstate: Optimize intel_pstate_set_policy
cpufreq: OMAP: instantiate omap-cpufreq as a platform_driver
arm: exynos: Enable OPP library support for exynos5440
cpufreq: exynos: Remove error return even if no soc is found
cpufreq: exynos: Add cpufreq driver for exynos5440
cpufreq: AMD "frequency sensitivity feedback" powersave bias for ondemand governor
cpufreq: ondemand: allow custom powersave_bias_target handler to be registered
cpufreq: convert cpufreq_driver to using RCU
cpufreq: powerpc/platforms/cell: move cpufreq driver to drivers/cpufreq
cpufreq: sparc: move cpufreq driver to drivers/cpufreq
...
Conflicts:
MAINTAINERS (with commit a8e39c3 from pm-cpuidle)
drivers/cpufreq/cpufreq_governor.h (with commit beb0ff3)
This merges in the revert of multiplatform support for exynos.
Trivial conflicts on removed code. Also, needed to add "select COMMON_CLK"
to the non-multiplatform EXYNOS config option.
* samsung/exynos-multiplatform:
Revert "ARM: exynos: enable multiplatform support"
Signed-off-by: Olof Johansson <olof@lixom.net>
This just merges in the revert of multiplatform support. Not doing it by
cherry-pick since we need the same revert in the next/drivers branch.
* samsung/exynos-multiplatform:
Revert "ARM: exynos: enable multiplatform support"
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit bd51de53e1.
Turns out that multiplatform breaks some uses cases, such as when you
have an existing defconfig, since it adds the new EXYNOS_SINGLE config
option as a dependecy. As a result, nearly all exynos config options
will be disabled by default.
Reverting instead of rebasing since this branch is pulled in as a
dependency elsewhere.
Signed-off-by: Olof Johansson <olof@lixom.net>
On device tree enabled exynos platforms, retrieve the physical base address
of the chip-id controller from device tree and create a virtual I/O mapping
for the chip-id controller. This helps to remove the chip-id controller entry
from the statically defined I/O mapping tables.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The en_core_tk_irqen flag is set in all the cpuidle driver which
means it is not necessary to specify this flag.
Remove the flag and the code related to it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org> # for mach-omap2/*
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This series contains the final pieces for Exynos multiplatform support:
Most of the patches are about the exynos-combiner irqchip, which is
converted to not rely on platform provided constants.
* samsung/exynos-multiplatform-drivers:
ARM: exynos: restore mach/regs-clock.h for exynos5
irqchip: exynos: look up irq using irq_find_mapping
irqchip: exynos: pass irq_base from platform
irqchip: exynos: localize irq lookup for ATAGS
irqchip: exynos: allocate combiner_data dynamically
irqchip: exynos: pass max combiner number to combiner_init
ARM: exynos: add missing properties for combiner IRQs
clocksource: exynos_mct: remove platform header dependency
clk: exynos: prepare for multiplatform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 6e6aac75 "ARM: EXYNOS: Migrate clock support to common
clock framework" from Thomas Abraham removed the Exynos5 specific
register definitions as they were unused at the time, but the
cpufreq driver actually still uses them.
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The platform code knows the IRQ base, while the irqchip driver
should really not. This is a littly hacky because we still
hardwire the IRQ base to 160 for the combiner in the DT case,
when we should really use -1. Removing that line will cause
a linear IRQ domain to be use, as we should.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
We can find out the number of combined IRQs from the device
tree, but in case of ATAGS boot, the driver currently uses
hardcoded values based on the SoC type. We can't do that
in general for a multiplatform kernel, so let's instead pass
this information from platform code directly in case of
ATAGS boot.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
For the non-DT case, the mct_init() function requires access
to a couple of platform specific constants, but cannot include
the header files in case we are building for multiplatform.
This changes the interface to the platform so we pass all
the necessary data as arguments to mct_init.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
The new common clock drivers for exynos are using compile
time constants and soc_is_exynos* macros to provide backwards
compatibility for pre-DT systems, which is not possible with
multiplatform kernels. This moves all the necessary
information back into platform code and removes the mach/*
header inclusions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@linaro.org>
These patches get us closer to adding multiplatform support on
the Exynos platform, they are part of a longer series of
patches. This would get all the simple stuff out of the
way, and I don't think there is a big risk of introducing
regressions with these.
A lot of the other patches have already been merged into
subsystem trees. After this series in in arm-soc, what is
left comes down to
* The ASoC conversion to dmaengine won't make it unless someone
who knows that code better steps up to do it right away. This
means that we won't have audio in a 3.10 multiplatform kernel
on Exynos, but it will still work for users that don't enable
multiplatform.
* The irqchip (combiner), clk and clksource patches are all based
on top of other changesets we pulled in from your trees, so I
would not make them part of the next/multiplatform branch. We can
apply them on top of the next/drivers branch once they are
tested successfully.
* A trivial patch is needed in the end to actually make
CONFIG_ARCH_EXYNOS visible in multiplatform configurations.
We will do that as a separate patch once everything else is
there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This makes it possible to enable the exynos platform as part of a
multiplatform kernel, in addition to keeping the single-platform
exynos support.
The multiplatform variant has a number of limitations at the moment:
* It only supports DT-enabled machines. This is not a problem in
the long run, as non-DT machines for exynos are going away.
The main problem here is that the gpio code and the exynos_eint
irqchip are not multiplatform capable but still required for
ATAGS based boot.
* The watchdog driver is still missing a conversion.
* sparsemem and memory_holes are currently not supported in
multiplatform.
The the multiplatform aware ARCH_EXYNOS Kconfig symbol is disabled
for now, as dependent patches are still pending in other
subsystem trees. We will enable it once everything comes together.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
plat/regs-sdhci.h is not used anywhere but in the sdhci-s3c
driver, so it can become a local file there and all other
inclusions removed.
plat/sdhci.h is used only to define the platform devices,
and with the exception of the platform_data structure not
needed by the driver, so we can split out the platform_data
definition instead and leave the rest to platform code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chris Ball <cjb@laptop.org>
The move is necessary to support early debug output on exynos
with multiplatform configurations. This implies also moving the
plat/debug-macro.S file, but we are leaving the remaining users of that
file in place, to avoid adding large numbers of extra configuration
options to Kconfig.debug
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When we enable CONFIG_SPARSE_IRQ, we have to set the value of NR_IRQS in
the machine_desc for legacy IRQ domains, and any file referring to the
number of interrupts or a specific number must include the mach/irqs.h
header file explicitly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As a preparation for multiplatform support, this introduces
a new Kconfig symbol to split the ATAGS based EXYNOS platforms
from the DT based ones. Turning off CONFIG_EXYNOS_ATAGS disables
all platforms that are not yet converted to DT, and we can
have code that relies on DT checking for this symbol being
disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the majority of cache flushing calls from the individual platform
files. This is now handled by the core code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The definitions have moved to include/linux/usb/samsung-usb-phy.h,
and plat/usb-phy.h is unavailable from drivers in a multiplatform
configuration.
Also fix up the plat/usb-phy.h header file to use the definitions
from the new header instead of providing a separate copy.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OPP library support is needed for exynos5440 cpu frequency
dynamic scaling driver.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Os9U
-----END PGP SIGNATURE-----
Merge tag 'mct-exynos-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
From Kukjin Kim <kgene.kim@samsung.com>:
add support exynos mct device tree and move into drivers/clocksource
* tag 'mct-exynos-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clocksource: mct: Add terminating entry for exynos_mct_ids table
clocksource: mct: Add missing semicolons in exynos_mct.c
ARM: EXYNOS: move mct driver to drivers/clocksource
ARM: EXYNOS: remove static io-remapping of mct registers for Exynos5
ARM: dts: add mct device tree node for all supported Exynos SoC's
ARM: EXYNOS: allow dt based discovery of mct controller using clocksource_of_init
ARM: EXYNOS: add device tree support for MCT controller driver
ARM: EXYNOS: prepare an array of MCT interrupt numbers and use it
ARM: EXYNOS: add a register base address variable in mct controller driver
Conflicts:
drivers/clocksource/Makefile
drivers/clocksource/exynos_mct.c
[arnd: adapt to CLOCKSOURCE_OF_DECLARE interface change]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The TWD and SCU configs are selected by default as long as
MSM_SCORPIONMP is false and/or MCT is false. Implementing the
logic this way certainly saves lines in the Kconfig but it
precludes those machines which select MSM_SCORPIONMP or MCT from
participating in the single zImage effort because when those
machines are combined with other SMP capable machines the TWD and
SCU are no longer selected by default.
Push the select out to the machine entries so that we can compile
these machines together and still select the appropriate configs.
Cc: Barry Song <baohua.song@csr.com>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Simon Horman <horms@verge.net.au>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A trivial patch to replace for_each_cpu(cpu_id, cpu_online_mask) by
the corresponding macro.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The cpuidle_register_driver return value is not checked.
The init function returns always -EIO when cpuidle_register_device
fails but the error could be different.
This patch fixes that by checking the cpuidle_register_driver properly
and returning the correct value when cpuidle_register_device fails.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The states are defined in the driver. We can get rid of the
intermediate cpuidle states initialization and the memcpy by
directly initializing the driver states.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Boards using secure firmware must use different CPU boot registers and
call secure firmware to boot the CPU.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On TrustZone-enabled boards the non-secure SYSRAM is used for secondary
CPU bring-up, so add a mapping for it.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
