debugfs_remove already check mwifiex_dfs_dir, so remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch uses WARN level is not printed by default.
In some cases, some boards have always met the unused log be printed as
follows.
...
[23193.523182] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2 & channel=13 freq=0
[23378.633684] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2 & channel=13 freq=0
Due to we used the wifi default area was US and didn't support 12~14
channels. As Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Also, as the commit 1b499cb72f
("mwifiex: disable channel filtering feature in firmware"), it proved to
be a feature to get better scan result from overlapping channel.
Even there could be AP from overlapping channel (might be 12/13/14
in this case), it will be filtered depend on reg domain rules.
e.g:
...
if (ch->flags & IEEE80211_CHAN_DISABLED)
continue;
So it should not been an ERROR, use the WARN level to instead it for now.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The REG_USTIME_TSF (US Time Tuning for TSF) definition of Realtek chips
should be 0x55C.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Julien Gomes says:
====================
ipmr/ip6mr: add Netlink notifications on cache reports
Currently, all ipmr/ip6mr cache reports are sent through the
mroute/mroute6 socket only.
This forces the use of a single socket for mroute programming, cache
reports and, regarding ipmr, IGMP messages without Router Alert option
reception.
The present patches are aiming to send Netlink notifications in addition
to the existing igmpmsg/mrt6msg to give user programs a way to handle
cache reports in parallel with multiple sockets other than the
mroute/mroute6 socket.
Changes in v2:
- Changed attributes naming from {IPMRA,IP6MRA}_CACHEREPORTA_* to
{IPMRA,IP6MRA}_CREPORT_*
- Improved packet data copy to handle non-linear packets in
ipmr/ip6mr cache report Netlink notification creation
- Added two rtnetlink groups with restricted-binding
- Changed cache report notified groups from RTNL_{IPV4,IPV6}_MROUTE to
the new restricted groups in ipmr/ip6mr
Changes in v3:
- Put message size calculation for {igmp,mrt6}msg_netlink_event in separate
functions
- Increased vif id attributes size from u8 to u32
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Netlink notifications on cache reports in ip6mr, in addition to the
existing mrt6msg sent to mroute6_sk.
Send RTM_NEWCACHEREPORT notifications to RTNLGRP_IPV6_MROUTE_R.
MSGTYPE, MIF_ID, SRC_ADDR and DST_ADDR Netlink attributes contain the
same data as their equivalent fields in the mrt6msg header.
PKT attribute is the packet sent to mroute6_sk, without the added
mrt6msg header.
Suggested-by: Ryan Halbrook <halbrook@arista.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Netlink notifications on cache reports in ipmr, in addition to the
existing igmpmsg sent to mroute_sk.
Send RTM_NEWCACHEREPORT notifications to RTNLGRP_IPV4_MROUTE_R.
MSGTYPE, VIF_ID, SRC_ADDR and DST_ADDR Netlink attributes contain the
same data as their equivalent fields in the igmpmsg header.
PKT attribute is the packet sent to mroute_sk, without the added igmpmsg
header.
Suggested-by: Ryan Halbrook <halbrook@arista.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RTNLGRP_{IPV4,IPV6}_MROUTE_R as two new restricted groups for the
NETLINK_ROUTE family.
Binding to these groups specifically requires CAP_NET_ADMIN to allow
multicast of sensitive messages (e.g. mroute cache reports).
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NEWCACHEREPORT message type to be used for cache reports sent
via Netlink, effectively allowing splitting cache report reception from
mroute programming.
Suggested-by: Ryan Halbrook <halbrook@arista.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The brcm43430 chip needs different firmware files for chip revision 0
and 1. The file currently in linux-firmware is for revision 1 only.
This commit makes brcmfmac request brcmfmac43430a0-sdio.bin instead
of brcmfmac43430-sdio.bin for revision 0 chips.
Note that the behavior for revision 1 chips is not changed, ideally those
would load brcmfmac43430a1-sdio.bin, but that will break existing setups.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Changing from a memcpy to per-member comparison left the
size variable unused:
net/ipv4/tcp_ipv4.c: In function 'tcp_md5_do_lookup':
net/ipv4/tcp_ipv4.c:910:15: error: unused variable 'size' [-Werror=unused-variable]
This does not show up when CONFIG_IPV6 is enabled, but the
variable can be removed either way, along with the now unused
assignment.
Fixes: 6797318e62 ("tcp: md5: add an address prefix for key lookup")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
in my commit b952f4dff2,
- *(u8 *)skb_put(skb_out, 1) = (u8)(accm >> 24); \
+ skb_put(skb_out, (u8)(accm >> 24)); \
it should skb_put_u8()
Fixes: b952f4dff2 ("net: manual clean code which call skb_put_[data:zero])")
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wireless drivers should not be using ioctl interface,
hence remove this interface for wil6210 driver.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After calling platform_ops.uninit() it is still possible to invoke
platform callbacks.
To prevent this, zero platform_ops right after invoking uninit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 supports VHT80 with 2x2. But it only support 1x1 with VHT160 or
VHT80+80. Inform userspace and the the QCA firmware about that limitation
whenever VHT80+80 or VHT160 is configured.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.
First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.
Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.
Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.
The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
message]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We recently refactored i40e_do_reset() and its friends to be able to
hold the RTNL lock only for the portions that actually need to be
protected. However, a separate refactoring added several new callers of
these functions during the PCIe error recovery and suspend/resume
cycles.
When merging the changes together, it was not noticed that we could
reduce the RTNL scope by letting the reset function handle the lock
itself, as previously it was not possible.
Fix this by replacing these call sites to indicate that the reset
function should handle its own lock. This enables multiple PFs to reset
or resume simultaneously without serializing the resets via the RTNL
lock. The end result is that on systems with lots of PFs and VFs the
resets don't stall waiting for each other to finish.
It is probable that we can also do the same for i40e_do_reset_safe, but
this author did not research that change carefully enough to be
confident.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When IWARP is enabled, we weren't clearing the PE_CRITERR, just logging
it and removing it from the mask. We need to do a corer to reset the
PE_CRITERR register, so set the bit for that as we handle the
interrupt.
We should also be checking for the error against the PFINT_ICR0 register,
and only need to clear it in the value getting written to
PFINT_ICR0_ENA.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When disabling interrupts, we should only be clearing the CAUSE_ENA bit,
not clearing the whole register. Clearing the whole register sets the
NEXTQ_IDX field to 0 instead of 0x7ff which can confuse the Firmware in
some reset sequences.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which the driver does not correctly exit overflow
promiscuous mode. This can occur if "too many" mac filters are added,
putting the driver into overflow promiscuous mode, and the filters are
then removed. When the failed filters are removed, the driver reports
exiting overflow promiscuous mode which is correct, however traffic
continues to be received as if in promiscuous mode still.
The bug occurs because the conditional for toggling promiscuous mode was
set to only execute when promiscuous mode was enabled and not when it
was disabled as well. This patch fixes the conditional to correctly
execute when promiscuous mode is toggled and not just enabled. Without
this patch, the driver is unable to correctly exit overflow promiscuous
mode.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for OEM firmware version. If OEM specific
adapter is detected ethtool reports OEM product version in firmware
version string instead of etrack id.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Partition bandwidth control is not in just one form of MFP (multi-function
partitioning), so make the code more generic and be sure to nudge the Tx
scheduler for all MFP.
Copyright updated to 2017.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check and message if the device is in
MFP mode as changing RSS input set is not supported in
MFP mode.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes parsing of FW 4.33 AQ command Get CEE DCBX OPER CFG (0x0A07).
Change is required because FW now creates the oper_prio_tc
nibbles reversed from those in the CEE Priority Group sub-TLV.
This change will only apply to FW 4.33 as future FW versions will use a
different function to parse the CEE data.
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a fix for the static code analysis issue where dcbcfg->numapps
could be greater than size of array (i.e dcbcfg->app[I40E_DCBX_MAX_APPS]).
The fix makes sure that the array is not accessed past the size of
of the array (i.e. I40E_DCBX_MAX_APPS).
Copyright updated to 2017.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port number passed when setting up
the UDP tunnel configuration to be in Little Endian format.
The i40e_aq_add_udp_tunnel command byte swaps the value from
host order to Little Endian.
Since commit fe0b0cd97b ("i40e: send correct port number to
AdminQ when enabling UDP tunnels") we've correctly
sent the value in host order.
Let's also add a comment to the function explaining that it must
be in host order, as the port numbers are commonly stored as Big
Endian values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When searching for the vf_capability client routine, dev_info() was
used, instead of the normal dev_dbg(). This causes the message to be
displayed at standard log levels which can cause administrators to
worry. Avoid this by using dev_dbg instead.
Copyright updated to 2017.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update a few flags related to FW interactions.
Copyright updated to 2017.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable num_active_queues represents the number of active queues we
have for the device. We assign this pretty early in i40evf_init_subtask.
Several code locations are written with loops over the tx_rings and
rx_rings structures, which don't get allocated until
i40evf_alloc_queues, and which get freed by i40evf_free_queues.
These call sites were written under the assumption that tx_rings and
rx_rings would always be allocated at least when num_active_queues is
non-zero.
Lets fix this by moving the assignment into the function where we
allocate queues. We'll use a temporary variable for storage so that we
don't assign the value in the adapter structure until after the rings
have been set up.
Finally, when we free the queues, we'll clear the value to ensure that
we do not loop over the rings memory that no longer exists.
This resolves a possible NULL pointer dereference in
i40evf_get_ethtool_stats which could occur if the VF fails to recover
from a reset, and then a user requests statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds proper XDP_TX action support. For each Tx ring, an
additional XDP Tx ring is allocated and setup. This version does the
DMA mapping in the fast-path, which will penalize performance for
IOMMU enabled systems. Further, debugfs support is not wired up for
the XDP Tx rings.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds basic XDP support for i40e derived NICs. All XDP
actions will end up in XDP_DROP.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Andrey reported a lockdep warning on non-initialized
spinlock:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 4099 Comm: a.out Not tainted 4.12.0-rc6+ #9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
register_lock_class+0x717/0x1aa0 kernel/locking/lockdep.c:755
? 0xffffffffa0000000
__lock_acquire+0x269/0x3690 kernel/locking/lockdep.c:3255
lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
__raw_spin_lock_bh ./include/linux/spinlock_api_smp.h:135
_raw_spin_lock_bh+0x36/0x50 kernel/locking/spinlock.c:175
spin_lock_bh ./include/linux/spinlock.h:304
ip_mc_clear_src+0x27/0x1e0 net/ipv4/igmp.c:2076
igmpv3_clear_delrec+0xee/0x4f0 net/ipv4/igmp.c:1194
ip_mc_destroy_dev+0x4e/0x190 net/ipv4/igmp.c:1736
We miss a spin_lock_init() in igmpv3_add_delrec(), probably
because previously we never use it on this code path. Since
we already unlink it from the global mc_tomb list, it is
probably safe not to acquire this spinlock here. It does not
harm to have it although, to avoid conditional locking.
Fixes: c38b7d327a ("igmp: acquire pmc lock for ip_mc_clear_src()")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes updates to mlx5 IPoIB netdevice driver (mlx5i),
1. We move ipoib files into separate directory, to allow it to grow
separately in its own space
2. Remove HW update carrier logic from IPoIB and VF representors profiles.
3. Add basic ethtool support. (Rings options/statistics and driver info).
4. Change MTU support.
5. Xmit path statistics reporting.
6. add PTP support.
For the new ethtool ops, PTP (ioctl) and change_mtu ndos in IPoIB, we didn't add new
implementation or new logic, we only reused those callbacks from the already existing
mlx5e (ethernet netdevice profile) and exposed them in IPoIB netdevice/ethtool ops.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZSR3rAAoJEEg/ir3gV/o+gjQIANM2xA8GN9Aji4DSK3iZyWAK
fN0T1soixQ2oYN/gLUNsRFpU9dPvgir4X/2RjNQQaV5UR/S83LcnDcQzzuuKrZ1l
ij1Dd//+U3e2EZTenV5tzvcEOKqnhFObyg3vQR5gC/IYhtzXBFKsCkjzymmP+9Gj
9k2zCvfkGN6aP9WJe/iNCvbbEgv+roVsdCP66wNzsfWFN9BwfSpW/5mXqmShN/58
odIDOWlKoumvpmU0K2v8xm4IAsTK9gW0PUfXCRhSTORvywzlc+WcZAUd1vrNlzk7
qKhfo6OpBaPRpmAb1zBAgTPuKDU9n58tF1nxI+X1Sxm99yj9Tah1R9+Q/NnEcuI=
=qPAM
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-06-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-06-20 (mlx5 IPoIB updates)
This series includes updates to mlx5 IPoIB netdevice driver (mlx5i),
1. We move ipoib files into separate directory, to allow it to grow
separately in its own space
2. Remove HW update carrier logic from IPoIB and VF representors profiles.
3. Add basic ethtool support. (Rings options/statistics and driver info).
4. Change MTU support.
5. Xmit path statistics reporting.
6. add PTP support.
For the new ethtool ops, PTP (ioctl) and change_mtu ndos in IPoIB, we didn't add new
implementation or new logic, we only reused those callbacks from the already existing
mlx5e (ethernet netdevice profile) and exposed them in IPoIB netdevice/ethtool ops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/net updates, part 2 (v2)
thanks for the feedback. Here's an updated patchset that honours
the reverse christmas tree and drops the __packed attribute. Please apply.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a s390 guest runs on a z/VM host that's part of a SSI cluster,
it can be migrated to a different host. In this case, the MAC address
it originally obtained on the old host may be re-assigned to a new
guest. This would result in address conflicts between the two guests.
When running as z/VM guest, use the diag26c MAC Service to obtain
a hypervisor-managed MAC address. The MAC Service is SSI-aware, and
won't re-assign the address after the guest is migrated to a new host.
This patch adds support for the z/VM MAC Service on L2 devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the hypervisor diagnose 0x26c
('Access Certain System Information').
It passes a request buffer and a subfunction code, and receives
a response buffer and a return code.
Also add the scaffolding for the 'MAC Services' subfunction.
It may be used by network devices to obtain a hypervisor-managed
MAC address.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's two spots in qeth_send_packet() where we don't accurately
account for transmitted packing buffers in qeth's performance
statistics:
1) when flushing the current buffer due to insufficient size,
and the next buffer is not EMPTY, we need to account for that
flushed buffer.
2) when synchronizing with the TX completion code, we reset
flush_count and thus forget to account for any previously
flushed buffers.
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add ipa return codes for Bridgeport (HiperSockets and OSA) according to
system level design.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two important fixes for brcmfmac. The rest of the brcmfmac patches are
either code preparation and fixing a new build warning.
brcmfmac
* fix a NULL pointer dereference during resume
* fix a NULL pointer dereference with USB devices, a regression from
v4.12-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZSSOQAAoJEG4XJFUm622browIAKdoXRzDj9t/r1s9UY+Fvm2w
YLiVCEy3Z/enF2iQcdmBC+uHNeaVWGctvjljxWwL6UsWx+Dl0/Dxcfilnan7SrYI
x5ysh+K4vfQ3oOf314vRuw+7u/h1WgobxdD9dgv7+C8yA7AIgHJlzZeM6PYdhibE
cEw/BOKDMDQ9NDnTJmaUmUogB/92TP3f5ACrNBe11kyPBtHuYFhNzee3PJQ3xP3I
D2knpUD3LtHhPDRC7ku9tpsmBpGHbOwGPHkLW1i9YhjHPe5ecmfvXtc7o/yUlLZK
f+xOMNuktUwsTjV0qhRnwx6Z2uJS1LlCmqVncaZIn7f+BYhORmTYIo45x628FGg=
=D6GF
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-06-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.12
Two important fixes for brcmfmac. The rest of the brcmfmac patches are
either code preparation and fixing a new build warning.
brcmfmac
* fix a NULL pointer dereference during resume
* fix a NULL pointer dereference with USB devices, a regression from
v4.12-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When having the skb pointer in the first descriptor, stmmac_tx_clean
can get called at a moment where the IP has only cleared the own bit
of the first descriptor, thus freeing the skb, even though there can
be several descriptors whose buffers point into the same skb.
By simply moving the skb pointer from the first descriptor to the last
descriptor, a skb will get freed only when the IP has cleared the
own bit of all the descriptors that are using that skb.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow two copies of the line 'up_write(&vf->efx->filter_sem);' got into
efx_ef10_sriov_set_vf_vlan(). This would put the mutex in a bad state and
cause all subsequent down attempts to hang.
Fixes: 671b53eec2 ("sfc: Ensure down_write(&filter_sem) and up_write() are matched before calling efx_net_open()")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network interface groups support added while ago, however
there is no IFLA_GROUP attribute description in policy
and netlink message size calculations until now.
Add IFLA_GROUP attribute to the policy.
Fixes: cbda10fa97 ("net_device: add support for network device groups")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 73ba57bfae ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad408 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae ("ipv6: fix backtracking for throw routes")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a bad thing not to handle errors when updating asoc. The memory
allocation failure in any of the functions called in sctp_assoc_update()
would cause sctp to work unexpectedly.
This patch is to fix it by aborting the asoc and reporting the error when
any of these functions fails.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
local_cork is used to decide if it should uncork asoc outq after processing
some cmds, and it is set when replying or sending msgs. local_cork should
always have the same value with current asoc q->cork in some way.
The thing is when changing to a new asoc by cmd SET_ASOC, local_cork may
not be consistent with the current asoc any more. The cmd seqs can be:
SCTP_CMD_UPDATE_ASSOC (asoc)
SCTP_CMD_REPLY (asoc)
SCTP_CMD_SET_ASOC (new_asoc)
SCTP_CMD_DELETE_TCB (new_asoc)
SCTP_CMD_SET_ASOC (asoc)
SCTP_CMD_REPLY (asoc)
The 1st REPLY makes OLD asoc q->cork and local_cork both are 1, and the cmd
DELETE_TCB clears NEW asoc q->cork and local_cork. After asoc goes back to
OLD asoc, q->cork is still 1 while local_cork is 0. The 2nd REPLY will not
set local_cork because q->cork is already set and it can't be uncorked and
sent out because of this.
To keep local_cork consistent with the current asoc q->cork, this patch is
to uncork the old asoc if local_cork is set before changing to the new one.
Note that the above cmd seqs will be used in the next patch when updating
asoc and handling errors in it.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch "call inet_add_protocol after register_pernet_subsys in dccp_v4_init"
fixed a null pointer dereference issue for dccp_ipv4 module.
The same fix is needed for dccp_ipv6 module.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now dccp_ipv4 works as a kernel module. During loading this module, if
one dccp packet is being recieved after inet_add_protocol but before
register_pernet_subsys in which v4_ctl_sk is initialized, a null pointer
dereference may be triggered because of init_net.dccp.v4_ctl_sk is 0x0.
Jianlin found this issue when the following call trace occurred:
[ 171.950177] BUG: unable to handle kernel NULL pointer dereference at 0000000000000110
[ 171.951007] IP: [<ffffffffc0558364>] dccp_v4_ctl_send_reset+0xc4/0x220 [dccp_ipv4]
[...]
[ 171.984629] Call Trace:
[ 171.984859] <IRQ>
[ 171.985061]
[ 171.985213] [<ffffffffc0559a53>] dccp_v4_rcv+0x383/0x3f9 [dccp_ipv4]
[ 171.985711] [<ffffffff815ca054>] ip_local_deliver_finish+0xb4/0x1f0
[ 171.986309] [<ffffffff815ca339>] ip_local_deliver+0x59/0xd0
[ 171.986852] [<ffffffff810cd7a4>] ? update_curr+0x104/0x190
[ 171.986956] [<ffffffff815c9cda>] ip_rcv_finish+0x8a/0x350
[ 171.986956] [<ffffffff815ca666>] ip_rcv+0x2b6/0x410
[ 171.986956] [<ffffffff810c83b4>] ? task_cputime+0x44/0x80
[ 171.986956] [<ffffffff81586f22>] __netif_receive_skb_core+0x572/0x7c0
[ 171.986956] [<ffffffff810d2c51>] ? trigger_load_balance+0x61/0x1e0
[ 171.986956] [<ffffffff81587188>] __netif_receive_skb+0x18/0x60
[ 171.986956] [<ffffffff8158841e>] process_backlog+0xae/0x180
[ 171.986956] [<ffffffff8158799d>] net_rx_action+0x16d/0x380
[ 171.986956] [<ffffffff81090b7f>] __do_softirq+0xef/0x280
[ 171.986956] [<ffffffff816b6a1c>] call_softirq+0x1c/0x30
This patch is to move inet_add_protocol after register_pernet_subsys in
dccp_v4_init, so that v4_ctl_sk is initialized before any incoming dccp
packets are processed.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With -Wformat-truncation, gcc throws the following warning.
Fix this by increasing the size of devname to accommodate 15 character
netdev interface name and description.
Remove length format precision for %s. We can fit entire name.
Also increment the version.
drivers/net/ethernet/cisco/enic/enic_main.c: In function ‘enic_open’:
drivers/net/ethernet/cisco/enic/enic_main.c:1740:15: warning: ‘%u’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 12 [-Wformat-truncation=]
"%.11s-rx-%u", netdev->name, i);
^~
drivers/net/ethernet/cisco/enic/enic_main.c:1740:5: note: directive argument in the range [0, 16]
"%.11s-rx-%u", netdev->name, i);
^~~~~~~~~~~~~
drivers/net/ethernet/cisco/enic/enic_main.c:1738:4: note: ‘snprintf’ output between 6 and 18 bytes into a destination of size 16
snprintf(enic->msix[intr].devname,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(enic->msix[intr].devname),
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%.11s-rx-%u", netdev->name, i);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in the IP that prevents us from enabling TSO for IPv6.
Before patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
882512708 bytes received in 00:14 (56.11 MiB/s)
After patch:
ftp fe80::2aa:bbff:fecc:1336%eth0
ftp> get /dev/zero
1203326784 bytes received in 00:12 (94.52 MiB/s)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
