When cable is not present the clock speed of some of the devices is
reduced based upon power saving mode setting in NVRAM. Due to this
NVRAM reads take long time to complete as a result CPU soft lockup
message is seen. Fix is to override clock, disable link aware and link
idle modes before NVRAM reads and restore them back after the reads
are complete. During this period also check if the thread needs to be
rescheduled and if there are any signals to handle.
Also decrease the NVRAM command execution timeout value to 1ms.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These "return 0;" uses seem wrong as there are
rc variables where error return values are set
but unused.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When umac_enable_set() is used to disable the UniMAC receiver or
transmitter, we need to make sure that we wait for a full-sized packet
to be processed because the UniMAC hardware stops on a packet boundary,
not immediately.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_unmap_single() was called with dma_unmap_len(cb, dma_len),
unfortunately we failed to assign this length field in
bcm_sysport_rx_refill() or bcm_sysport_alloc_rx_bufs() using
dma_unmap_len_set().
This causes packet contents corruption because are we not invoking the
cache invalidation routines with the proper length. Fix this by using
the full RX buffer size (RX_BUF_LENGTH) because the mappings for the RX
bufers are created with that size.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets need to be at least 64 bytes to enter the switch port logic,
including the FCS, otherwise they will be discarded as RUNT packets.
With packets having Broadcom tags, the 4-bytes tag is first stripped
off the packet, and the packet length is then checked, so we need to
make sure that the packet length with FCS is at least 64 bytes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link adjustment callback can be called as frequently as desired by
the PHY library, as such, let's avoid doing a Read/Modify/Write sequence
if nothing changed, which is more than likely since we are interfaced
with a switch device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any TSO fragment hits hardware bug conditions (e.g. 4G boundary), the
driver will workaround by calling skb_copy() to copy to a linear SKB. Users
have reported page allocation failures as the TSO packet can be up to 64K.
Copying such a large packet is also very inefficient. We fix this by using
existing tg3_tso_bug() to transmit the packet using GSO.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 uses GSO as workaround if the hardware cannot perform TSO on certain
packets. We should not modify the ip header fields if we do GSO on the
packet. It happens to work by accident because GSO recalculates the IP
checksum and IP total length.
Also fix the tg3_start_xmit comment to reflect that this is the only
xmit function for all devices.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build when BNX2X_SRIOV is not enabled.
Change one parameter struct from bnx2 to bnx2x and don't return a value
from a void function.
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: 'struct bnx2' declared inside parameter list [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:60: warning: 'return' with a value, in function returning void [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91ebb928b "bnx2x: Add support for Multi-Function UNDI" contains a bug
which prevent the emptying of the device's Rx buffers before reset.
As a result, on new boards it is likely HW will reach some fatal assertion
once its interfaces load after UNDI was previously loaded.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook the Broadcom SYSTEMPORT driver into the build system under the
SYSTEMPORT Kconfig symbol.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT is the latest Ethernet MAC hardware block used on newer
BCM7xxx Set Top Box SoCs in conjunction with an internal Ethernet
switch. This patch adds support for this hardware block along with the
following hardware features:
- support for hardware checksum offload (transmit and receive)
- support for the 32 transmit queues
- MIB counters reading
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 2dc33bbc "bnx2x: Remove the sriov VFOP mechanism",
the bnx2x started enforcing vlan credits for all vlan configurations.
This exposed 2 issues:
- Vlan credits are not returned once a VF is removed; this causes a leak
of credits, and eventually will lead to VFs with no vlan credits.
- A vlan credit must be set aside for the Hypervisor to use, and should
not be visible to the VF.
Although linux VFs at the moment do not support vlan configuration [from the
VF side] which causes them to be resilient to this sort of issue, Windows VF
over linux hypervisors might fail to load as the vlan credits become depleted.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VF interface, the driver fails to release that VF's mailbox
and bulletin board allocated memory.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ARRAY_SIZE macro to determine the number of entries in
bcm_enet_gstrings_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a problem with dropped jumbo frames after usage of
'ethtool -G ... rx'.
Scenario:
1. ip link set eth0 up
2. ethtool -G eth0 rx N # <- This zeroes rx-jumbo
3. ip link set mtu 9000 dev eth0
The ethtool command set rx_jumbo_pending to zero so any received jumbo
packets are dropped and you need to use 'ethtool -G eth0 rx-jumbo N'
to workaround the issue.
The patch changes the logic so rx_jumbo_pending value is changed only if
jumbo frames are enabled (MTU > 1500).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP isn't enabled, bnx2_suspend/resume are unused; don't
build them when they aren't used.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
version.h inclusion is not necessary as detected by versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x driver fails to build on ARM with:
In file included from drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:28:0:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h:243:1: error: unknown type name 'irqreturn_t'
irqreturn_t bnx2x_msix_sp_int(int irq, void *dev_instance);
^
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h:251:1: error: unknown type name 'irqreturn_t'
irqreturn_t bnx2x_interrupt(int irq, void *dev_instance);
^
Nothing in bnx2x_link.c or bnx2x_cmn.h is explicitly including the irq
definitions, so we add an include of linux/irq.h to pick them up.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2dc33bbc4 "bnx2x: Remove the sriov VFOP mechanism" introduced a possible
memory leak on the error flow during multicast filters configuration.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the UniMAC block is configured to forward the CRC as part of the
Ethernet frame (priv->crc_fwd_en, set by default), enabling the hardware
RX checksum block unveiled that the dma_rxchk_bit was never set in the
per-packet status bits (dma_flag in bcmgenet_desc_rx). This would make
the chksum_ok variable to be never set to 1, and the networking stack
would have to compute the packet checksums, which takes a substantial
amount of time.
In order for the RXCHK block to properly compute the packet checksum in
hardware, we also need to set the RBUF_SKIP_FCS bit accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 370d4a26 "bnx2x: Create workqueue for IOV related tasks" breaks bnx2x
compilation when CONFIG_BNX2X_SRIOV is not set - "multiple definition of
`bnx2x_schedule_iov_task'".
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Including hardware acceleration features in vlan_features breaks
stacked vlans (Q-in-Q) by marking the bottom vlan interface as
capable of acceleration. This causes one of the tags to be lost
and the packets are sent with a sing vlan header.
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a VF's Rx Mode will be configured to support promiscuous mode
the PF will comply, causing the VF to actually become promiscuous.
This will enable the VF to see all unicast traffic which might be intended for
other VMs, which we believe should not be possible.
This patch will cause the hypervisor to ignore the VF's request for changes in
its Rx mode (other than disabling it), preventing it from becoming promiscuous.
Reported-by: Yoann Juet <yoann.juet@univ-nantes.fr>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently showing port statistics, although they can't really access
those - thus all such statistics will always show a value of 0.
This patch removes said statistics from the VF's view as to not confuse the
user.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we now posses a workqueue dedicated for sriov, the paradigm that sriov-
related tasks cannot sleep is no longer correct.
The VFOP mechanism was the one previously supporting said paradigm - the sriov
related tasks were broken into segments which did not require sleep, and the
mechanism re-scheduled the next segment whenever possible.
This patch remvoes the VFOP mechanism altogether - the resulting code is a much
easier to follow code; The segments are gathered into straight-forward
functions which sleep whenever neccessary.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x sriov mechanisms were done in the bnx2x slowpath workitem which
runs on the bnx2x's workqueue; This workitem is also responsible for the bottom
half of interrupt handling in the driver, and specifically it also receives
FW notifications of ramrod completions, allowing other flows to progress.
The original design of the sriov reltaed-flows was based on the notion such
flows must not sleep, since their context is the slowpath workitem.
Otherwise, we might reach timeouts - those flows may wait for ramrod completion
that will never arrive as the workitem wlll not be re-scheduled until that same
flow will be over.
In more recent time bnx2x started supporting features in which the VF interface
can be configured by the tools accessing the PF on the hypervisor.
This support created possible races on the VF-PF lock (which is taken either
when the PF is handling a VF message or when the PF is doing some slowpath work
on behalf of the VF) which may cause timeouts on the VF side and lags on the PF
side.
This patch changes the scheme - it creates a new workqueue for sriov related
tasks and moves all handling currently done in the slowpath task into the the
new workqueue.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in a new management feature which needs the driver versions
(bnx2x, bnx2fc and bnx2i) loaded for each interface.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2/bnx2x rings are made up of linked pages. However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface. In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE. On archs with >= 64K PAGE_SIZE, it generates some compile
warnings. Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl. In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table. If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
