Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz. A similar fix was done
for sdhci-pci, however in the sdhci-acpi case the
HID/UID is not unique so the capabilities register
values are matched also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass HID and UID to probe_slot so extra setup
can be done for specific ids.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UID was made available on acpi_device since
commit ccf7804026 ("ACPI: Add _UID support for ACPI devices.")
Use it from there instead of reprocessing the
ACPI object info.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The __initconst is in the wrong place, and when moved to the correct place
it uncovers an error where the variable is used by non-init data structures.
Instead merely make them const and put the const in the right spot.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let a driver override the timeout clock frequency by
populating it before calling sdhci_add_host(). Note
the value will otherwise be zero because sdhci_host is
zeroed when allocated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for card detect for Bay Trail
and Braswell SD Card host controllers in PCI
mode.
This uses the gpio descriptor API which can find
gpio descriptors, for example, on an ACPI comapnion
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a HID (INT33BB) and UID (3) for a SD Card host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a quirk for a host controller that always sets
a Transfer Complete interrupt status for the stop
command even when a busy response is not indicated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 98e90de99a
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.
It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe"),
the atmci_probe() function calls atmci_cleanup_slot in the failure path.
This causes a new warning whenever the driver is built:
WARNING: drivers/mmc/host/built-in.o(.init.text+0xa04): Section mismatch in reference from the function atmci_probe() to the function .exit.text:atmci_cleanup_slot()
The function __init atmci_probe() references
a function __exit atmci_cleanup_slot().
Gcc correctly warns about this function getting dropped in the link stage
for the built-in case, which would cause undefined behavior when this error
path is hit. The solution is to simply drop the __exit annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe")
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP2_NO_PRESCAN_POWERUP and MMC_CAP2_FULL_PWR_CYCLE for
rtsx_pci_sdmmc and rtsx_usb_sdmmc to reflect properties of Realtek
card reader hosts.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We find tuning timeout because of the secure erase operation lasts too
long, so don't do tuning when device is busy.
Signed-off-by: Yi Sun <yi.y.sun@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change takes care of releasing mmc resources on error cases in
probe function which was missing. Also release timer in remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change uses managed resource APIs to allocate resources such as,
clk, gpio, io in order to simplify the driver unload or failure cases.
Hence does away with release statements of the same resources in error
labels and remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we're tuning on a big-endian CPU we'll never determine we properly
tuned the device because we compare the data we received from the
controller with a table that assumes the CPU is little-endian.
Change the table to be an array of bytes instead of 32-bit words
so we can use memcmp() without needing to byte-swap every word
depending on the endianess of the CPU.
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Fixes: 415b5a75da "mmc: sdhci-msm: Add platform_execute_tuning implementation"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I spent a couple of days with the driver just hanging due to me forgetting to
specify the external crystal frequency, so that clk_get_rate() returned 0 and
thus the loop in tmio_mmc_set_clock() never ended. I don't think that's an
acceptable behavior, so I suggest that the minimum frequency is checked for 0
in tmio_mmc_host_probe().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ian Molton <ian.molton@codethink.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio is using sd_ctrl_read16/write16_rep()
for data transfer.
It works if transfer size was even number,
but, last 1 byte will be ignored if
transfer size was odd number.
This patch adds new tmio_mmc_transfer_data()
and solve this issue.
Tested-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_of_find_slot_node() is only used in dw_mci_of_get_slot_quirks()
if CONFIG_OF is defined, thus there is no need to have a !CONFIG_OF
version of it. Fixes the following compile warning with !CONFIG_OF:
CC [M] drivers/mmc/host/dw_mmc.o
drivers/mmc/host/dw_mmc.c:2223:28: warning: ‘dw_mci_of_find_slot_node’ defined but not used [-Wunused-function]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0dcaa2499b improved error
handling of sdhci_add_host. However, "err_of_parse" and "err_cd_req"
should be placed after "pm_runtime_disable(&pdev->dev)".
Signed-off-by: Xiang Wang <wangx@marvell.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch renames sdio flag in vendor data to st_sdio, as this flag is
only used to enable ST specific sdio setup. This will also ensure that
the ST specfic setup is not done on other vendor like Qualcomm.
Originally the issue was detected while testing WLAN ath6kl on IFC6410
board with APQ8064 SOC.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds sdio enable mask in variant data, SOCs like ST have
special bits in datactrl register to enable sdio. Unconditionally setting
this bit in this driver breaks other SOCs like Qualcomm which maps this
bits to something else, so making this enable bit to come from variant
data solves the issue.
Originally the issue is detected while testing WLAN ath6kl on Qualcomm
APQ8064.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the MMCI driver will only handle GPIO descriptors
implicitly through the device tree probe glue in mmc_of_init(),
but devices instatiated other ways such as through board files
and passing descriptors using the GPIO descriptor table will
not be able to exploit descriptors.
Augment the driver to look for a GPIO descriptor if device
tree is not used for the device, and if that doesn't work,
fall back to platform data GPIO assignment using the old
API. The end goal is to get rid of the platform data integer
GPIO assingments from the kernel.
This enable the MMCI-embedding platforms to be converted to
GPIO descritor tables.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, sh_mobile_sdhi can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, tmio_mmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, omap_hsmmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to HW issue, SDHCI host controller on Intel
Baytrail/Merrifield platforms can not use preset
register. So, disable preset registers for them by quirks.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Right now enable 1.2v IO voltage for SDHC is by using vqmmc.
Thus for the host which doesn't have vqmmc, or its vqmmc does
not support 1.2v, directly use MMC_CAP2_HS200 may cause HS200
failure.
So needs to check if vqmmc is able to support 1.2v. If it does
not support, disable 1.2v IO for HS200.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the clock prepare and unprepare call to the driver set_ios calls
phase. This will remove a warning once the PXA architecture is migrated
to the clock infrastructure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Similar to sdhci-pci controller, also add probe_slot
and remove_slot method in the sdhci-acpi driver.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.
"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."
This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.
Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>
Changes since v1:
Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
and Tested if issue is fixed again.
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Tested-by: Youssef TRIKI <youssef.triki@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_disable_irq_wakeups() is exported, but it is not called outside sdhci.c.
Make it static and do not export it, so that the following sparse warning is
fixed:
drivers/mmc/host/sdhci.c:2548:6: warning: symbol 'sdhci_disable_irq_wakeups' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The timeout_clk calculation code for SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK case
is common and could be moved into common sdhci_do_set_ios, then platform code
which is not using sdhci_set_clock does not need to write the same code again.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The timeout_clk calculation code in sdhci_add_host is meaningless for
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
So only execute them with no SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK set.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci driver write 0xE into timeout counter register to
set the maximum timeout. The value is not correct for uSDHC since the
max counter value for uSDHC is 0xF.
Instead of using common timeout code in sdhci, we implement esdhc_set_timeout
to handle the difference between eSDHC and uSDHC.
Currently we simply set the max timeout value as before.
But in the future, we probably may implement IMX specific timeout
setting algorithm and use suitable timeout for different CMDs.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the common code assume 0xE is the maximum timeout counter
value and use it to write into the timeout counter register.
However, it's fairly possible that some other SoCs may have different
max timeout register value. That means 0xE may be incorrect and
becomes meaningless.
It's also possible that other platforms has different timeout
calculation algorithm. To be flexible, this patch provides a .set_timeout
hook for those platforms to set the timeout on their way if they need.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci code use the 1 << 27 as the max timeout counter to
to calculate the max_busy_timeout, however it's not correct for uSDHC
since its the max counter is 1 << 28.
Implement esdhc_get_max_timeout_cout to handle it correctly.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the max timeout count is hardcode to 1 << 27 for calcuate
the max_busy_timeout, however, for some platforms the max timeout
count may not be 1 << 27, e.g. i.MX uSDHC is 1 << 28.
Thus 1 << 27 is not correct for such platform.
It is also possible that other platforms may have different values.
To be flexible, we add a get_max_timeout_count hook to get the correct
maximum timeout value for these platforms.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even). Let's pass
those errors back.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the implementation of CSR SDHCI controller is a modified version of
the one described in the 1.0 specification, and not a normal 3.0
controller.
and 8bit-width enable bit of CSR MMC hosts is 3, while stardard hosts
use bit 5.
this patch fixes the functionality of 8bit transfer in mmc controllers
and improve performance for mmc0 a lot.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Declare ERASE capability so we can use filesystems with the discard
option and the fstrim tool.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
