1. now pxa_camera.c uses ioremap() for register access, pxa_camera.h is
totally useless. Remove it.
2. <asm/dma.h> does no longer include <mach/dma.h>, include the latter
file explicitly
delete mode 100644 drivers/media/video/pxa_camera.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all architectures provide clear_user_page(), but clear_user_highpage()
is available everywhere at least via the compatibility inline function.
Is this the "trivial patch" that's required for these two drivers?
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a number of drivers which set their i2c bus class to
I2C_CLASS_CAM_DIGITAL, however no chip driver actually checks for this
flag, so we might as well drop it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
f_op->poll is the only vfs operation which is not allowed to sleep. It's
because poll and select implementation used task state to synchronize
against wake ups, which doesn't have to be the case anymore as wait/wake
interface can now use custom wake up functions. The non-sleep restriction
can be a bit tricky because ->poll is not called from an atomic context
and the result of accidentally sleeping in ->poll only shows up as
temporary busy looping when the timing is right or rather wrong.
This patch converts poll/select to use custom wake up function and use
separate triggered variable to synchronize against wake up events. The
only added overhead is an extra function call during wake up and
negligible.
This patch removes the one non-sleep exception from vfs locking rules and
is beneficial to userland filesystem implementations like FUSE, 9p or
peculiar fs like spufs as it's very difficult for those to implement
non-sleeping poll method.
While at it, make the following cosmetic changes to make poll.h and
select.c checkpatch friendly.
* s/type * symbol/type *symbol/ : three places in poll.h
* remove blank line before EXPORT_SYMBOL() : two places in select.c
Oleg: spotted missing barrier in poll_schedule_timeout()
Davide: spotted missing write barrier in pollwake()
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Brad Boyer <flar@allandria.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several subsystem open handlers dereference the fops_get() return value
without checking it for nullness. This opens a race condition between the
open handler and module unloading.
A module can be marked as being unloaded (MODULE_STATE_GOING) before its
exit function is called and gets the chance to unregister the driver.
During that window open handlers can still be called, and fops_get() will
fail in try_module_get() and return a NULL pointer.
This change checks the fops_get() return value and returns -ENODEV if NULL.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The radio_release function of the BTTV driver is missing a call to
v4l2_prio_close. As a result, after the radio device has been opened at
least once (e.g., by HAL during bootup), v4l2_priority will never drop below
V4L2_PRIORITY_INTERACTIVE again. With the following patch against 2.6.28,
applications that run with V4L2_PRIORITY_BACKGROUND are able to open devices
again. Previous Linux versions are affected as well.
Signed-off-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code had calls to both usb_set_intfdata and dev_set_drvdata, doing the
same thing.
The semantic patch that lead to finding this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@header@
@@
@same depends on header@
position p;
@@
usb_set_intfdata@p(...) { ... }
@depends on header@
position _p!=same.p;
identifier _f;
struct usb_interface *intf;
expression data;
@@
_f@_p(...) { <+...
- dev_set_drvdata(&intf->dev, data);
+ usb_set_intfdata(intf, data);
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The GPIO logic for LNA control on the Tiger r2 devices was inverted.
This patch corrects the problem.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Report to userspace that cx24116 and stv0899 drivers support DVB-S2.
Signed-off by: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices require different setups on struct_audio. Due to that, we
may need to change some fields at dev.adev during device probe. So, this
patch moves the dynamic memory allocation of adev at em28xx-alsa to the
dynamic allocation of struct em28xx dev that happens during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes autodetection for Avermedia AVerTV GO 007 FM Plus (M15C)
(PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Avermedia AVer TV GO 007 FM Plus (M15C) on
saa7134 driver (PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for radio driver TEA5764 from NXP.
This chip is connected in pxa I2C bus in EZX phones
from Motorola, the chip is used in phone model A1200.
This driver is for OpenEZX project (www.openezx.org)
Tested with A1200 phone, openezx kernel and fm-tools
[mchehab@redhat.com: Fixed CodingStyle and solved some merge conflicts]
Signed-off-by: Fabio Belavenuto <belavenuto@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix I2C bridge error in zl10353 if no tunner attached to internal I2C
bus of zl10353 chip.
When set enable bridge from internal I2C bus to the main I2C bus
(saa7134) the main I2C bus stopped very hardly. No any communication. In
our next board we solder additional resistors to internal I2C bus.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since ttusb_dec.c relies on pci_alloc_consistent and
pci_free_consistent, make it depend on PCI in Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since dvb-ttusb-budget.c relies on pci_alloc_consistent and
pci_free_consistent, make it depend on PCI in Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.
Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.
Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This rename prevents conflicts with the older compat_ioctl32 module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since internal to v4l2 the ioctl prototype is the same regardless of it
being called through .ioctl or .unlocked_ioctl, we need to convert it all
to the long return type of unlocked_ioctl.
Thanks to Jean-Francois Moine for posting an initial patch for this and
thus bringing it to our attention.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (583 commits)
V4L/DVB (10130): use USB API functions rather than constants
V4L/DVB (10129): dvb: remove deprecated use of RW_LOCK_UNLOCKED in frontends
V4L/DVB (10128): modify V4L documentation to be a valid XHTML
V4L/DVB (10127): stv06xx: Avoid having y unitialized
V4L/DVB (10125): em28xx: Don't do AC97 vendor detection for i2s audio devices
V4L/DVB (10124): em28xx: expand output formats available
V4L/DVB (10123): em28xx: fix reversed definitions of I2S audio modes
V4L/DVB (10122): em28xx: don't load em28xx-alsa for em2870 based devices
V4L/DVB (10121): em28xx: remove worthless Pinnacle PCTV HD Mini 80e device profile
V4L/DVB (10120): em28xx: remove redundant Pinnacle Dazzle DVC 100 profile
V4L/DVB (10119): em28xx: fix corrupted XCLK value
V4L/DVB (10118): zoran: fix warning for a variable not used
V4L/DVB (10116): af9013: Fix gcc false warnings
V4L/DVB (10111a): usbvideo.h: remove an useless blank line
V4L/DVB (10111): quickcam_messenger.c: fix a warning
V4L/DVB (10110): v4l2-ioctl: Fix warnings when using .unlocked_ioctl = __video_ioctl2
V4L/DVB (10109): anysee: Fix usage of an unitialized function
V4L/DVB (10104): uvcvideo: Add support for video output devices
V4L/DVB (10102): uvcvideo: Ignore interrupt endpoint for built-in iSight webcams.
V4L/DVB (10101): uvcvideo: Fix bulk URB processing when the header is erroneous
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_is_isoc_in(epd)
usb_endpoint_is_isoc_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: clean up
RW_LOCK_UNLOCKED is deprecated. This patch replaces it with the
__RW_LOCK_UNLOCKED(lock) macro. This change was a little trickier than
others due to the macro being used in another macro that fills an array.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by gcc:
drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c: In function ‘hdcs_set_size’:
drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c:301: warning: ‘y’ may be used uninitialized in this function
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was trying to query the AC97 registers for the vendor
information even if it was clearly not a AC97 audio device (resulting in errors
in the dmesg output). This was due to a bug in the way we did the check.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add additional output formats, which will be useful for the Pinnacle PCTV
Ultimate 880e integration with the saa7136.
Thanks to Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Noticed when doing the audio support for the Pinnacle PCTV HD Ultimate 808e
that the modes were incorrect (the 808e uses I2S in 5 sample mode)
Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Like the em2874, the em2870 does not have any analog support, so don't bother
loading the em28xx-alsa module.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pinnacle 80e cannot be supported since Micronas yanked their driver
support for the drx-j chipset at the last minute. Remove the device profile
since it cannot work without the drx driver and it being there is only likely
to confuse people into thinking the device is supported but not working.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DVC 100 profile is redundant since we already have an existing identical
profile named "Pinnacle Dazzle DVC 90/DVC 100"
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct problem introduced during the board refactoring where the XCLK
frequency would get zero'd out. The sequence of events was as follows:
em28xx_pre_card_setup() called em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration
em28xx_pre_card_setup() would set the dev->board.xclk if not set
em28xx_pre_card_setup() would set the XCLK register based on dev->board.xclk
...
em28xx_card_setup() would call em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration (clearing out
value of dev->board.xclk set in em28xx_pre_card_setup)
...
em28xx_audio_analog_set() sets the XCLK register based on dev->board.xclk
(which now contains zero)
The change sets the default XCLK and I2C Clock fields in the board definition
inside of em28xx_set_model() so that subsequent calls do not cause the
values to be overwritten.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix this warning:
drivers/media/video/zoran/zoran_card.c:156: warning: ‘zr36067_pci_tbl’ defined but not used
Currently, zoran driver relies on a find routine that doesn't use the
pci table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_set_coeff’:
drivers/media/dvb/frontends/af9013.c:231: warning: ‘ns_coeff2_8k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:230: warning: ‘ns_coeff2_2k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:229: warning: ‘ns_coeff1_8193nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:228: warning: ‘ns_coeff1_8192nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:227: warning: ‘ns_coeff1_8191nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:226: warning: ‘ns_coeff1_2048nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_snr’:
drivers/media/dvb/frontends/af9013.c:1012: warning: ‘snr_table’ may be used uninitialized in this function
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed to sync with the development tree. Probably, a merge
conflict were solved by adding this blank line.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/usbvideo/quickcam_messenger.c: In function ‘qcm_sensor_init’:
drivers/media/video/usbvideo/quickcam_messenger.c:450: warning: operation on ‘ret’ may be undefined
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes this warning:
drivers/media/video/gspca/gspca.c:1811: warning: initialization from incompatible pointer type
The reason is that the returned argument should be a long, not an
integer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/anysee.c: In function ‘anysee_master_xfer’:
drivers/media/dvb/dvb-usb/anysee.c:156: warning: ‘ret’ may be used uninitialized
By looking at the function, altrough very unlikely, this might
eventually be true if num = 0. So, better to fix the warning by
initializing with ret = 0.
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend the range of supported UVC devices by allowing video output devices
matching the following structure:
TT_STREAMING -> VC_PROCESSING_UNIT -> VC_EXTENSION_UNIT{0,n} -> OTT_*
Video output devices are reported with the V4L2_CAP_VIDEO_OUTPUT capability
flag and are subject to the same restrictions as video input devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Built-in iSight webcams have an interrupt endpoint but spit proprietary data
that don't conform to the UVC status endpoint messages. Don't try to handle
the interrupt endpoint for those cameras.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the first bulk URB of a video payload contains an erroneous header, or
when no V4L2 buffer is available, the whole payload must be dropped. Change
the skip logic to drop all bulk URBs until the end of the payload instead of
the first one only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This camera is rather similar to MT9M001, but also has a couple of
enhanced features, like pixel binning.
create mode 100644 drivers/media/video/mt9t031.c
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't modify driver's state in try_fmt, just verify format acceptability
or adjust it to driver's capabilities.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
priv->scale is checked in start_capture.
Therefore, it should be NULL if failing in set_fmt.
This patch resolve this problem.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds tw9910 driver that use soc_camera framework.
It was tested on SH Migo-r board and mplayer.
create mode 100644 drivers/media/video/tw9910.c
create mode 100644 include/media/tw9910.h
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sh_mobile_ceu_camera.c is already prepared to support interlaced format, this
patch moves the choice of a field type down to host and / or camera drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch cleans up the sh_mobile_ceu driver and adds comments and
constants to clarify the magic sequence in sh_mobile_ceu_capture().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch presents new method to be able to select V4L2 input type
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch presents new method to be able to check v4l2_std_id
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds NV16/NV61 support to the sh_mobile_ceu driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds NV12/NV21 support to the sh_mobile_ceu driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move mutex from host drivers to camera device object, take into account
videobuf locking.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the introduction of the format conversion support in soc-camera, we now
also have to take care to pass the correct pixel format to the camera driver
when calling its try_fmt() method.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplify multiple drivers by replacing f->fmt.pix.* with a single pointer
dereference, merge some needlessly broken lines, verify host and camera
operations pointers on registration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the sh_mobile_ceu driver to make use
of the new pixel format translation code. Only pass-though
mode at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using PXA270's FIFO inactivity time-out register (CITOR) reduces FIFO overruns.
The time-out is calculated in CICLK / LCDCLK ticks and has to be longer than
one pixel time. For this we have to know the pixel clock frequency, which
usually is provided by the camera. We use the struct soc_camera_sense to
request PCLK frequency from the camera driver upon each data format change.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Antonio Ospite <ospite@studenti.unina.it> two platforms with a
mt9m111 camera require opposite pixel clock polarity, which means one of them
inverts it. This patch adds support for inversion flags and switches all
available camera drivers to using them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"static" on stv06xx for all static functions and parameters to avoid
such troubles.
Cc: Erik Andren <erik.andren@gmail.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Testing for non-NULL platform-data is not enough, we have to check if the GPIO
in the platform data is valid or not. Also see my earlier patch:
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Micron mt9m111 offers 4 byte orders for YCbCr
output. This patchs adds all possible outputs capabilities
to the mt9m111 driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch replace return -1; with return retval; in 3 functions.
And we also change if-checks for this returned values.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a lot of patches for dsbr100 last time we should update version
of driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should use dev_err (not dev_warn) if video_register_device fails.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should make if-constructions more clear. Introduce int retval
variables in some functions to make it this way. Also a lot of useful
dev_err messages added. And now we check every returned value after
usb_control_msg.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove printk in one line and place dev_warn there.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch corrects unplug procedure. Patch adds
usb_dsbr100_video_device_release, new macros - videodev_to_radio, mutex
lock and a lot of safety checks.
Struct video_device videodev is embedded in dsbr100_device structure.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Because this device doesn't provide any powermanagment capabilities(may
be they exist but unknown to me yet, so they are not implemented), we
should turn them off. Patch sets support_autosuspend equal to 0.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch corrects unplug procedure, that was implemented wrong in
previous patch. New function usb_amradio_device_release added.
Disconnect lock removed.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The po1030 never sends long i2c messages, no need to test for that in
the init phase.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the s5k83a sensor to use the common read_sensor function
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the s5k4aa sensor to use the common read_sensor function
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Toggle read sensor sequence depending on type of sensor. Check that no
more than max width of a sensor is read.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
First step into unifying the read and write sensor functions
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This restores the correct boolean expression
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The buffer type is already checked in v4l2-ioctl.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- move the rev12a sequence from setcontrast to end of start
- add the white balance control for rev72a
- adjust the contrast formula
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the initialization of the URB list for a DVB-USB device to prevent
problems on certain platforms (MIPS).
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, just two routines are enough for analog: the first one configs the analog
part and register V4L2 devices, and the second one release analog devices.
After this patch, it will be easier to transform em28xx-video into an em28xx
extension, loaded only on analog devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-video were holding several code that are not specific to V4L2
interface.
This patch moves the core code for em28xx-core, and usb probing code
into em28xx-cards.
This opens the possibility of breaking em28xx into a core module and a
V4L2 module, loaded only on devices that have analog interfaces.
Some cleanup may be done at em28xx-cards to optimize the config code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements VIDIOC_ENUM_FRAMESIZES, it is used at least
by gstreamer.
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p.h defines a few extern symbols when CONFIG_DVB_DIB7000P is not set. since the
header is used on more than one driver, this causes symbol duplication, as pointed by
Ingo Molnar <mingo@elte.hu>:
drivers/media/dvb/built-in.o: In function `dib7000p_set_gpio':
(.text+0x3f242): multiple definition of `dib7000p_set_gpio'
drivers/media/video/built-in.o:(.text+0xb8c1e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_i2c_enumeration':
(.text+0x3f282): multiple definition of `dib7000p_i2c_enumeration'
drivers/media/video/built-in.o:(.text+0xb8c3e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_set_wbd_ref':
(.text+0x3f1c1): multiple definition of `dib7000p_set_wbd_ref'
drivers/media/video/built-in.o:(.text+0xb8bfe): first defined here
LD drivers/net/built-in.o
make[2]: *** [drivers/media/built-in.o] Error 1
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_device can set that as parent pointer in the v4l2_dev
field instead of using the struct device parent field.
This allows v4l2-dev.c to check whether this driver is v4l2_device based,
and if so then it can offer additional services.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of relying on the cdev release callback we should rely on the
release callback from the device struct. This requires that we use
get_device/put_device to do proper refcounting. In order to do this
safely v4l2-dev.c now sets up its own file_operations that call
out to the driver's ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usbvideo_ClientIncModCount may return value < 0 in the case of error, not > 0.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted to v4l2_subdev. While doing that I also discovered a stray 'break'
that broke the S_CTRL handling. Fixed that as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver can be coupled to an anciliary AC97 chip. This patch
allows read/write AC97 registers directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_index requires a valid parent device in order to discover which
indices are in use. Some drivers (e.g. pvrusb2) do not set the parent
device. In that case just return 0.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bt832 i2c driver was never used or even compiled and is no longer
maintained. It is now removed completely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a consistent crystal value of 28.636360 MHz for computing all PLL
parameters so clocks don't have relative error due to assumed crystal
value mismatches. Also aimed to have all PLLs run their VOCs at close to
400 MHz to minimze the error of these PLLs as frequency synthesizers. Also
set the VDCLK and AIMCLK PLLs to sane values before the APU and CPU firmware
are loaded. Also fixed I2S Master clock dividers.
Many thanks to Mike Bradley and Jeff Campbell for reporting this problem and
suggesting the solution, researching and experimenting, and performing
extensive testing to support their suggested solution.
Reported-by: Jeff Campbell <jac1dlists@gmail.com>
Reported-by: Mike Bradley <mike.bradley@incanetworks.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable AV_LOCK, locking of audio PLL to video PLL in the cx18-av-core for
analog captures. It seems to have adverse effects on captures from
SVideo and CVBS sources with current clock & crystal settings in the driver.
Many thanks to Jeff Campbell and Mike Bradley for reporting this problem,
and suggesting the solution and performing extensive testing to support their
suggestion.
Reported-by: Jeff Campbell <jac1dlists@gmail.com>
Reported-by: Mike Bradley <mike.bradley@incanetworks.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added all missing v4l1/2 ioctls and fix several broken conversions.
Partially based on work done by Cody Pisto <cpisto@gmail.com>.
Tested-by: Brandon Jenkins <bcjenkins@tvwhere.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the gp8psk module to use the S2API.
It pretends to be DVB-S2 capable in order to allow the various
supported modulations (8PSK, QPSK-Turbo, etc), and keep software
compatibility with the S2API patches for Mythtv and VDR.
Signed-off by: Alan Nisota <alannisota@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch uses the same code for enumberating video formats that are
present on cx88, bttv and saa7134 drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The changeset 78aa52a159cf introduced a bug on em28xx: buffer setup should be
awaking xc3028. Instead, since we didn't specify the tuner mode, the device
were going to sleep, due to the lack of tuner mode when asking tuner to handle
VIDIOC_S_FREQUENCY:
xc2028 0-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
xc2028 0-0061: divisor= 00 00 14 d0 (freq=83.250)
xc2028 0-0061: Putting xc2028/3028 into poweroff mode.
xc2028 0-0061: Printing sleep stack trace:
Pid: 10936, comm: mplayer Tainted: P M 2.6.27.8 #1
Call Trace:
[<ffffffffa0b759ea>] xc2028_sleep+0x89/0x1ab [tuner_xc2028]
[<ffffffffa0b48fb9>] tuner_s_frequency+0xf5/0x165 [tuner]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init_fw option was broken for the HVR-950q because we would call the reset
callback inside of dvb_attach() and the callback had not been setup yet.
Michael Krufky (who added the init_fw feature) says it's no longer required,
so just remove the option completely.
Thanks to user Zzeiss from #linuxtv chat for reporting the issue and
Michael Krufky <mkrufky@linuxtv.org> for proposing the fix.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't operate under the assumption that every device that uses the em2820
default USB ID is a Prolink PlayTV USB. We have an eeprom hash, so use that,
since otherwise we cannot support other devices with the 2820 default USB ID
(such as the ADS Tech Instant TV USB USBAV-704)
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the em2870 to the list of known em28xx chip ids.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans-up the advise/acquire methods.
This has been tested on the hvr-1300/4000 and assumed to be
correct on the hvr-3000.
This update also fixes analogue tuning on the hvr-1300
when in blackbird mode.
Signed-off-by: Darron Broad <darron@kewl.org>
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been noticed that in HW tuning mode in cx24123.c that
a check is made to not alter the status var when in one shot
mode, a simpler solution is to not update here for all cards.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delsys was missing when searching for FEC in table.
This fixes FEC lookup for DVB-S2 QPSK modulation.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tuner-xc3028 can be put to sleep to save power. However, if not properly
recovered from sleep, the device won't work. It is noticed that some
devices doesn't recover properly, so let's add a dump_stack() as a debug
option, to allow us to track when this happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes/fixes on em28xx dev->lock:
- em28xx_init_dev() were unlocking without a previous lock;
- some read ioctls need to lock after the removal of KBL, since a write
may be happening at the same time an ioctl is reading;
- keep the device locked during all device initialization;
- lock/unlock while reading/writing registers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_try_fmt_vid_cap() just checks if a given resolution is supported.
It doesn't touch on struct em28xx device descriptor. so, there's no need
to lock.
While there, use unlikely() for those values that aren't likely to
occur.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for absolute and continuous zoom controls (mapped to absolute
and relative UVC zoom controls).
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update v4l2_ctrl_get_name() and v4l2_ctrl_get_menu() with missing
control names and menu values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refine the firmware load and firmware startup process. Significant changes
are to ensure the SCB and IPC area are correct before starting up the firmware,
and letting the CPU firmware start up the APU firmware for us.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Use a known open task handle when setting stream CX2341x parameters
Sometimes, we might only have VBI or YUV stream open instead of an MPEG stream.
Let's make sure we use a valid task handle to perform the CX2341x control
settings.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VBI comment corrections to avoid future confusion about standards.
Comments on cx18 VBI implementation shortcomings that need resolution.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed magic number that referred to firmware limit on the number of
MDLs the firmware can maintain for any stream at any one time.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Uwe Bugla pointed out that there are some more typos in some print-statements. Fixed.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a typo in cx24113.c.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed some minor coding style issues and some driver information
printed when using the driver on a board.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original version of sccb_read_reg() is from Jim Paris.
NOTE: as it is now reading sensor ID won't work for sensors on different
i2c slave address.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vc0321 sends some additional data after sending the complete
frame, we ignore this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for getting and setting framerate via v4l2 controls,
rather than setting a fixed value at module insertion.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add get_streamparm and set_streamparm operations so subdrivers can
get/set stream parameters such as framerate.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set frame format registers 0x0a and 0x0b to explicit values
rather than relying on reset-time defaults.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frame data in bulk transfers is separated into 2048-byte payloads.
Each payload has its own header.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sensor was declared as hdcs2020.
The new exchanges have been extracted from the ms-win file usbvm31b.inf.
The light frequency control has been added.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch moves the last fid and pts from static to the sd structure.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The indirect registers at 0x1c/0x1d control frame settings. If we
leave the values at 0x0a and 0x0b at their reset-time defaults, frame
data from the camera matches the UVC payload format. This lets us
better reassemble the data into frames and know when data was lost.
This also lets us relax the bulk_size requirement from 600K to 2K,
which should help systems on with limited RAM (like the PS3).
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frame size is too small, so we lose the last YUYV pixel.
Fix the setup and remove the last_pixel hack.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The colors control (saturation) acted as color balance.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The brightness jumped from max to min at the middle of the control values.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add helper functions to load i2c sub-devices, integrating them
into the v4l2-framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for the OMAP2 camera block. OMAP2 is used in e.g. Nokia
N800/N810 internet tablet.
This driver uses the V4L2 internal ioctl interface.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds support for the CX24113 DVB-S tuner driver and thus support for the Technisat Skystar2 revision 2.8.
The driver was created with the help of Technisat. Thank you very much.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bogus controls currently include processing unit auto controls for which no
corresponding manual control is available. Such auto controls make little
sense if any, and are known to crash at least the SiGma Micro webcam.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver drops incomplete uncompressed video frames to avoid confusing
userspace with corrupt data. Add a nodrop module parameter to turn that
behaviour off and make all frames available to userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A combined authorship patch from Hans Verkuil and Andy Walls. Raw
VBI can now be captured but requires a video capture to be in progress as well.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a port of the fixes Hans Verkuil made for ivtv/cx25840:
The service_set field was used to determine whether raw or sliced VBI was
desired. This is incorrect since it is perfectly valid to select sliced VBI
with a service_set of 0.
Instead the driver should check on VIDIOC_S_FMT whether the type
field matches the raw or sliced VBI type.
Updated the cx18 driver accordingly, including an additional check in
cx18_start_v4l2_encode_stream() that didn't exist in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Avoid making firmware API calls with the queue lock held. The source
of MPEG strem corruption when not holding the queue lock was found to be that
the MPEG buffer could be retrieved by the user app before it was sync'ed for
the host cpu. Incoming buffers are now sync'ed before being put on q_full and
releasing the queue lock. We can thus avoid the sometimes lengthy call to
the firmware for CPU_DE_SET_MDL while holding the queue lock, so we can get
better performance.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Increment version number due to siginificant buffering changes.
Now version 1.0.4
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Add module parameters for finer control over buffer allocations.
User now has the option of setting smaller buffers to get lower
latency transfers from the encoder. User can also now set the number
of buffers used for a stream explicitly.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Allow more than 63 capture buffers in rotation per stream. Implement
q_busy to hold buffers the firmware has for use. q_free holds truly unused
buffers in a pool. New buffers are given to the firmware as soon as the
firmware returns one, if there are any to give to the firmware.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Eliminate q_io from stream buffer handling in anticipation of upcoming
changes in buffer handling. q_io was a holdover from ivtv and it's function
in cx18 was trivial and not necessary. We just push things back onto the
front of q_full now, instead of maintaining a 1 buffer q_io queue.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
How to enable the mpeg encoder is not found yet.
The card comes up with gpio 0x0820000 for DVB-T.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the function cx88_audio_initdev, the value card has been created using
snd_card_new. The other error handling code in this function frees the
value using snd_card_free. I have thus changed the first error case to do
the same. On the other hand, it may be that card is not sufficiently
initialized at this point to use snd_card_free, in which case something
else should be done to free the memory in the error case.
In the function snd_cx88_create the call kfree(chip) in one error case
looks suspicious, both because it is not done in the other error code, and
because chip points into the middle of the memory allocated by
snd_card_new, ie it is not itself associated with a separate kmalloc.
Therefore I have removed it.
The semantic match that finds the first problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = snd_card_new(...)) == NULL) S
|
x@p1 = snd_card_new(...);
)
... when != snd_card_free(...,(T)x,...)
when != if (...) { <+... snd_card_free(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != snd_card_free(...,(T1)x,...)
when != if (...) { <+... snd_card_free(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
@ script:python @
p1 << r.p1;
p3 << r.p3;
@@
print "* file: %s snd_card_new: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Compro VideoMate E650F (DVB-T part only).
The card based on cx23885 PCI-Express chip, xc3028 tuner and ce6353 demodulator.
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the new format-negotiation infrastructure, support all four YUV422
packed and the planar formats.
The new translation structure enables to build the format
list with buswidth, depth, host format and camera format
checked, so that it's not done anymore on try_fmt nor
set_fmt.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allocate and fill a list of formats, supported by this specific
camera-host combination. Use it for format enumeration. Take care to stay
backwards-compatible.
Camera hosts rely on sensor formats available, as well as
host specific translations. We add a structure so that hosts
can define a translation table and use it for format check
and setup.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We anyway don't follow the s_fmt_vid_cap / g_fmt_vid_cap / try_fmt_vid_cap
naming, and soc-camera is so far only about video capture, let's simplify
operation names a bit further. set_fmt_cap / try_fmt_cap wasn't a very good
choice too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pixel format requested by the user is not necessarily the same, as what
a sensor driver provides. There are situations, when a camera host driver
provides the required format, but requires a different format from the
sensor. Further, the list of formats, supported by sensors is pretty static
and can be pretty good described with a constant list of structures. Whereas
decisions, made by camera host drivers to support requested formats can be
quite complex, therefore it is better to let the host driver do the work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.try_bus_param() method from struct soc_camera_host_ops is only called at one
location immediately before .try_fmt_cap(), there is no value in keeping these
two methods separate, merge them.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: cx18_writel_expect() should not declare success on a PCI read error.
This removes the potential for cx18_write*_expect() calls to not
accomplish a PCI write successfully as expected. The CX18-AV core uses the
*expect() calls often and this may be the source of intermittent audio
problems and standands switching problems.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Change to per CX23418 device work queues for deferrable work handling.
Needed to support 2.6.22 and earlier kernels that can't selectively cancel
work orders. Also will provide slightly better performance on SMP systems.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda8290 were using some random video standard for FM. This results on random
errors. Instead, program tda8290 in expert mode, using a configuration near the
one specified on NXP datasheet for tda8295 (available on their site).
Also, properly display that the device is on radio mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probably due to a removed code, tda827x were doing some wrong calculus at the
returned frequency. I suspect that the original idea were to return the
programmed divisor converted into frequency again.
However, the current code is sometimes multiplying the programmed frequency by
62500, and, on other cases, like radio, it dividing it by 1000.
Instead of doing such math, let's just store the frequency value as requested by
the caller module.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this
development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c: In function 'xc2028_sleep':
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c:1111: warning: 'return' with no value, in function returning non-void
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx devices generally get hot when xc3028 tuner is powered on. This
patch solves this by turning power off when the device is not used, at the
expense of having a higher load time, when calling a TV application.
Since firmware load happens on 1 or 2 seconds on most devices, this is not a pain.
Also, it helps to save the planet by saving some power :)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the firmware load is now fast on most boards, better to keep the tuner
off by default. A modprobe parameter were added to keep the old behavior,
to be used by old devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change log format to look more like URB transactions. In fact, setup and
IN/OUT transactions are merged. This helps to debug the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power the LNA while the frontend is in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Quiet a sometimes common warning that often has benign consequences.
No one probably cares that the firmware took forever to ack our command, as
they always seem to succeed whether or not the firmware acks it in a reasonable
amount of time.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the version number due to significant changes in the way the
mailboxes and interrupts are handled.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add copyright attribution for files modified by awalls in 2008
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Adjust outgoing mailbox timeouts and remove statistics logging.
This saves some wasted storage in struct cx18 for each card. Cutting
the outgoing mailbox timeouts in half from the previous value appears to
be safe with MythTV. Got rid of interrupted case code path after
a wait uninterruptable returns.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore buffers that have fallen out of the transfer rotation, and check
for coherent mailbox data when processing a stale mailbox.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unnecessary MMIO accesses in time critical irq handling path. Also
ensured that the mailbox ack field is read in last, so we know for sure if we
have a stale mailbox or not on receipt.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Streamline cx18-io[ch] wrappers and enforce MMIO retry strategy so that
write retries always occur and read retries never occur (as they never help).
Remove MMIO statistics logging to speed up MMIO accesses. Deprecate & ignore
retry_mmio and mmio_ndelay module parameters, to essentially force
retry_mmio=1 and mmio_ndelay=0.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Propagate staleness of mailbox and mdl ack data to work handler to let
the work handler know that the data from the encoder may not be coherent.
Allows for smarter handling of buffers in future, to deal with MDLs that fall
out of rotation due to irq handler being late in collecting mailbox and mdl ack
info.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the per stream queue spinlocks into mutexes. All queue
manipulation happens via the work queue or system calls into the driver, and
not in an interrupt context. This reduces the amout of time the cx18 driver
keeps interrupts disabled.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change to singlethreaded global work queue thread for deferable work,
instead of the kernel default multithreaded work queue. This ensures
execution of deferable work is always in the proper order, so caputred buffers
don't get reordered.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A major rewrite of interrupt handling for incoming mailbox processing, to split
the timing critical steps from the the deferrable steps as the sending XPU on
the CX23418 will time out and overwrite our incoming mailboxes rather quickly.
Setup a pool of work "order forms" for the irq handler to send jobs to the new
work handler routine which uses the kernel default work queue to do the
deferrable work. Started optimizing some of the cx18-io calls as they are now
the low hanging fruit for recoving microseconds back from the timeline.
Future optimizations will get rid of mmio read retries, mmio stats logging, and
combine smaller functions in the irq path into the larger ones to save ~2 us
each.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes problems(kernel oopses) with unplug of device while
it's working.
Patch adds disconnect_lock mutex, changes usb_amradio_close and
usb_amradio_disconnect functions and adds a lot of safety checks.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If APU firmware file read failed, the jump vector to the APU was undefined and
the APU would be started executing garbage. Fix uninitialized variable to be
an infinite loop for the APU, but also bail out before even starting the APU.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the CX23418 CPU unit sent out an ack interrupt to the linux driver, it
also received that interrupt and cleared the flag before the linux driver could
see what the interrupt was for. This fix prevents the CPU from receiving an
IRQ for it's own outgoing ack's to the linux driver. This fix is critical now
that the linux driver doesn't poll but relies on these ack interrupts.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the APU fw start address from rom file instead of a hardcoded entry vector.
Fixed cx18_setup_page() calls to use the correct APU image load addresses.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All waits for cx18 mailbox API commands are now uninterruptable. Added
code to collect mailbox ack statistics. Tweaked timeouts based on collected
stats and video vertical frame and field rates.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Improve handling of outgoing mailboxes detected to be busy. When
encountering a busy mailbox, sleep instead of polling, and wait for interrupt or
timeout. If the mailbox is still busy, force it free. When sending commands,
make sure we never create a situation where we mark the mailbox busy upon
sending, and ensure we always have a method to cleanly recover from a busy
mailbox.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver interrupt and mailbox handling has change significantly.
Time for a roll to v1.0.2.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add mutexes to ensure exclusive access for outgoing driver to CX23418 mailboxes.
Also wait on a waitq for mailbox acknowledgement from the CX23418 instead of
polling.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Use default kernel work queue; fix streaming flag for work handler.
Eliminate cx18 specific work queue and use the kernel default work queue.
Fixed the F_STREAMING_FLAG for the TS stream so cx18_dvb_work_handler()
can know when it is not safe to send MDLs to the firmware.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Reduce number of mmio read retries to improve performance. Experiments
have shown 2 things: read retries never improve the result of a suspect mmio
read from the CX23418 (the result stays all 0xff's), and that most of the
suspected read failures are actually proper reads of values that should be
all 0xff's. This change reduces the number of read retries and keeps the
count separate from write retries.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note:
* At High Symbol Rates we do not have enouph machine cycles to handle the
incoming symbols and hence might run into problems at the very end of the
specified definition
* Most of the equations have been calculated for a master clock of 99 MHz,
running at 90MHz, raises lot of issues such as the need to recalculate
all of them , which is eventually very painful.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several chips may be turned off when the device is not used, like audio,
video and dvb demods. This patch adds a gpio callback at the core
structs to allow turning off such devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous changeset moved gpio from em28xx struct into em28xx_board.
However, the driver were not updated to properly honor those gpio's.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch, several devices without tuner were kept the value 0
for tuner_type. However, this means TUNER_TEMIC_PAL. Replace those
entries for the proper TUNER_ABSENT value.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of a large, ugly switch specifying the gpio tables for each
device, let's move it into the boards struct. This also helps to see
what boards have already the gpio's for DVB.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaces all occurrences of em28xx_write_regs_req() and em28xx_write_reg()
used to setup register names by em28xx_write_reg().
Also, documents the register names that are known.
This patch were generated by this small perl script:
my %reg_map = (
# Register table - the same as defined on parse_em28xx.pl script
);
while (<>) {
if (m/(.*)em28xx_write_regs_req\(dev\,\s*0x00\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
my $reg = $2;
my $val = $3;
$val =~ tr/A-f/a-f/;
$reg = $reg_map{$reg} if defined($reg_map{$reg});
printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
} elsif (m/(.*)em28xx_write_regs\(dev\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
my $reg = $2;
my $val = $3;
$val =~ tr/A-f/a-f/;
$reg = $reg_map{$reg} if defined($reg_map{$reg});
printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
} else {
print $_;
}
}
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, the first message states board names. Also, removed printing the alternate
settings by default. I2C messages are now clearer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since saa7115 has saa711x chip auto-detection, there's no need on differenciating
it at cards table. Just use the generic name for all boards that use a philips
saa711x decoder.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several fields are duplicated on both structs. Let's just copy em28xx_board instead.
A later cleanup could just copy the fields that are changed, in order to keep em28xx_board
const.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unused em28xx_board.vchannels and em28xx.video_channels.
Also, .is_em2800 = 0 is not needed, as all data is zeroed by kernel loader.
The table also included a notice that svideo weren't test on Hauppauge
USB2. Remove this notice, since this input also works properly.
Also, it does some whitespace cleanups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous patches removed XCLK and I2C magic. Now, we finally know
what those registers do. Also, only a very few cards need different
setups for those.
Instead of keeping the setups for those values inside the per-device
hack magic switch, move the uncommon values to the board-specific
struct, and have a common setup for all other boards.
So, almost 100 lines of hacking magic were removed.
A co-lateral effect of this patch is that it also fixes a bug at em28xx-core, where xclk
were set, without taking any care about not overriding a previous xclk setup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup the calls to set the GPIOs and GPOs for various devices,
replacing the register number with the #define from em28xx-reg.h and
converting over to using em28xx_write_reg()
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert over to setting the XCLK register usage with the new em28xx_write_reg()
function.
Thanks to Ray Lu from Empia for providing the em2860/2880 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides USB suspend and hibernation support
for Siano's SMS chipset based USB device
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable power LED while the frontend is in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some em28xx devices, there's an unused interface. This is printed on
the logs as an error. We can just ignore that interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The OmniVision OV534 is the USB bridge chip used in Sony Playstation EYE,
it is found also in other webcams like Hercules Blog Webcam and
Hercules Dualpix HD.
This driver is the port to gspca of a prototype driver by Mark Ferrell
based on vivi. The original code to initialize the camera and start the
capture is from Jim Paris on ps2dev.org, here integrated with the analysis
of the USB communications taken by the windows driver.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sn9c105 and sn9c120 bridges must be differently programmed for the ov7660.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The msi gx7xx range of computers seem to be a strange lot with lots of different sys vendor names and differently oriented sensors. This commit adds another quirk for a range of them.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gspca conversion deprecated a number of defines. Remove them.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bridge takes some time to update after a write, so apps doing a quick
write/read can get the old value back.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the spca501 driver only works the first time used, then the cam needs
to be unplugged or the driver reloaded, this is because currently the data
which should be send each time the stream is started is send only once.
Likewise currently the data to initialize the cam is send from the probe
function, and thus will not get send after a suspend/resume.
This patch fixes this by sending both at the right time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams with image transfer by bulk messages accept one or many
permanent bulk read.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new exchanges are adapted from MS-win traces and the webcams work better.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver sn9c102 has no code for the ov7648 sensor.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is much more readable to swap the byteorder in the switch rather
than in each case statement.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This Patch does modify the bttv-cards.c and bttc.h so that the driver
supports VD-011, VD-012, VD-012-X1 and VD-012-X2 Framegrabber from
Phytec Messtechnik GmbH.
Signed-off-by: Dirk Heer <d.heer@phytec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If removing and reiserting the driver on some devices, tuner type will
be unset at the second time. This patch fixes this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch cleans up the entries of xc2028/3028, since those devices
don't need or use a tda9887.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pixelview uses a Sigmatel stac codec. It has an external line out pin,
connected to AC97_MASTER_VOL. It also provides I2S output, but using a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices use more than one AC97 outputs. This patch allows such
devices to properly work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some boards use different AC97 setups for output. This patch adds the
capability of specifying the output to be used. Currently, only one
output is selected, but the better is to allow user to select it via a
mixer, on alsa driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for the Digittrade DVB-T USB Stick remote.
As the Digittrade USB stick identifies itself as a generic Afatech AF9015
device, the remote cannot be autodetected. To enable it, add the following
to /etc/modprobe.d/dvb-usb-af9015 or /etc/modprobe.conf:
options dvb-usb-af9015 remote=4
Signed-off-by: Alain Kalker <miki@dds.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a trailing newline character after calling v4l_printk_ioctl() to avoid
messing the kernel log up and merge the uvc_v4l2_ioctl message with the ioctl
name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sonix-based cameras seem to require the host to commit video streaming
parameters before selecting the alternate endpoint. While most applications
issue a VIDIOC_S_FMT ioctl before starting streaming, this is not required
by the V4L2 specification.
The problem has been noticed on Ubuntu 8.10 with applications using libv4l.
The library blocks VIDIOC_S_FMT calls when the requested format is identical
to the currently selected format. As the driver commits video streaming
parameters when initialising the device, only the first run of a
libv4l-enabled application would succeed.
For the sake of completeness, experiment showed that the camera keeps sending
12 bytes isochronous packets (header only, no data) without toggling the FID
bit if video streaming parameters haven't been committed before selecting the
alternate endpoint.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the calls that write the i2c clock register over to the new
em28xx_write_reg() function that allows for or'ing bits
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a new function that writes to a single register. This is
useful because the vast majority of register writes are a single
register, and this format permits or'ing register value bits together.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Please accept this patch to refer to my new email address
Signed-off-by: Jelle Foks <jelle@foks.us>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AC97 devices provide several input and outputs. However, before this
patch, em28xx device weren't properly allowing the usage of ac97
possible combinations. Also, several input volumes were left untouched,
instead of making sure that the volumes were set on mute state.
This patch improves support for ac97 devices by allowing to use any
inputs, and making sure that unused inputs are set on mute state.
Yet, some work is still needed to select the AC97 output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes easier to identify vendor ID, since AC97 vendors are
generally identified by 3 bytes. The remaining byte is used by the
vendor to identify its devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch properly implements audio handling on em28xx. Before this
patch, it was assumed that every device has an Empia 202 audio chip.
However, this is not true.
After this patch, specific AC97 chipset setup and configurations can be
done.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
audio mux entries were described by 0 and 1 magic numers. Use an enum
alias for each entry type.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make use of the em28xx chip configuration register to determine whether
we have AC97 audio, I2S audio, or no audio support at all.
Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously, AC97 registers were named as if they were part of em28xx
device, generating some confusion. Replace such names for a more general
naming convention.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@i@
@@
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(E[...]))
+ ARRAY_SIZE(E)
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All noticed by sparse:
drivers/media/dvb/dvb-usb/cinergyT2-core.c:35:5: warning: symbol 'disable_remote' was not declared. Should it be static?
drivers/media/dvb/dvb-usb/cinergyT2-core.c:48:23: warning: symbol 'cinergyt2_usb_device' was not declared. Should it be static?
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:160:15: warning: cast to restricted __le16
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:190:9: warning: cast to restricted __le32
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:208:9: warning: cast to restricted __le32
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:227:24: warning: cast to restricted __le16
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: warning: incorrect type in assignment (different base types)
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: expected unsigned short [unsigned] [assigned] [usertype] tps
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: got restricted __le16 [usertype] <noident>
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: warning: incorrect type in assignment (different base types)
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: expected unsigned int [unsigned] [assigned] [usertype] freq
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: got restricted __le32 [usertype] <noident>
Cc: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Place the s5h1411 into low power mode until first use (to handle the case where
the user plugs in the device and then doesn't use it for a while). On the
Pinnacle 801e, this brings the power usage from 126ma down to 82ma.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the ATI TV Wonder HD 600 USB Remote Control
(required a new keymap)
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactor the em28xx IR support based on the em2860/em2880 and em2874
datasheets.
Tested on the HVR-950 (em2883), Pinnacle 800e (em2883), Pinnacle 80e (em2874)
using the remote controls that came with those products.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first em28xx were based on i2c IR's. However, some newer designs
are coming with a polling-based IR. Those are done by reading a register
set at em28xx.
This patch adds core polling support for those devices. Later patches will
add support for some device-specific IR's.
This patch adds the same basic IR polling code used by bttv, cx88 and saa7134, and
shares the common getkey masks defined at ir-common.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add registration for Pinnacle 80e ATSC tuner
Register the em2874 based Pinnacle 80e device. Note that support for this
device also requires the new drx-j driver (which is not available yet)
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Thanks to Joerg Schindler from Pinnacle for providing sample hardware.
Thanks to Rainer Miethling from Pinnacle for providing engineering support.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly support capture start on em2874
The transport stream enable register moved in the em2874, so make it work
properly.
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the logic so that the em28xx-alsa module does not get loaded for devices
that don't support analog audio (such as the em2874)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Empia moved around their endpoint configuration in newer chips, so accommodate
the changes
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix case where we could end up dereferencing a NULL pointer if dev->vdev or
dev->vbi_dev were not set properly.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Empia switched to a 16-bit addressable eeprom in newer devices. While we
could certainly write a routine to read the eeprom, there is nothing of use
in there that cannot be accessed through registers, and there is the risk that
we could corrupt the eeprom (since a 16-bit read call is interpreted as a
write call by 8-bit eeproms). So just be safe and bail out of the function.
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Empia moved the location of the GPIO/GPO registers in newer devices. Add the
ability to specify the relocated registers (including caching of register
contents).
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When setting up the device, remember the chip id, so we can control behavior
in the future without having to read the register continuously.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a EM28XX_NODECODER option to the list of available decoders. This option
becomes important for devices that do not have analog support.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add em2874 chip id
Add chip id for em2874 to list of known chips
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_ioctl2 lacks implementation of those two ioctls:
- VIDIOC_ENUM_FRAMESIZES and VIDIOC_ENUM_FRAMEINTERVALS
Adds implementation for those.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans-up MFE attachment for saa-7134 dvb
devices.
note: MFE is not fully implemented here yet.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans-up MFE attachment for these cards plus
two cases of potential memory leak on attachment
failure.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Failed requests will now generate a one-time warning message instead of the
usual "Failed to query..." error, which should be more user-friendly. The
driver will also recover automatically from failed GET_MIN/GET_MAX requests
when the device is half-broken without requiring the MINMAX quirk (fully
broken devices still need the quirk).
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to http://bugzilla.kernel.org/show_bug.cgi?id=11997,
the driver sn9c102 does not work for this webcam.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to http://bugzilla.kernel.org/show_bug.cgi?id=11920,
the driver sn9c102 does not work for this webcam.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for suspend and resume methods in driver.
Without this kradio and gnomeradio crashes during resume.
Also .supports_autosuspend in usb_driver struct set equal to 0 to avoid
suspending of module if usb_autosuspend enabled.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
