With the error message I added in "libfc: sanity check cpu number
extracted from xid" I didn't account for the fact that fc_exch_find is
called with FC_XID_UNKNOWN at the start of a new exchange if we are the
responder.
It doesn't come up with the initiator much, but that's basically every
exchange for a target. By checking the xid for FC_XID_UNKNOWN first, we
not only prevent the erroneous error message, but skip the unnecessary
lookup attempt as well.
[mkp: applied by hand due to conflict with Hannes' libfc patch series]
Signed-off-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a case where gate work is called as part of cancel work from ungate
path the clk state would be marked as REQ_CLKS_ON. There is no point
gating the clocks and then end up turning them ON immediately in ungate
work, save time by skipping the gate work and change the clk state to
CLKS_ON as they are not turned off yet.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ungate work turns on the clock before it exits hibern8, if the link
was put in hibern8 during clock gating work. There occurs a race
condition when clock scaling work calls ufshcd_hold() to make sure low
power states cannot be entered, but that returns by checking only
whether the clocks are on. This causes the clock scaling work to issue
UIC commands when the link is in hibern8 causing failures. Make sure we
exit hibern8 state before returning from ufshcd_hold().
Callstacks for race condition:
ufshcd_scale_gear
ufshcd_devfreq_scale
ufshcd_devfreq_target
update_devfreq
devfreq_monitor
process_one_work
worker_thread
kthread
ret_from_fork
ufshcd_uic_hibern8_exit
ufshcd_ungate_work
process_one_work
worker_thread
kthread
ret_from_fork
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case the power configuration fails, skip further processing of the
probing function and return immediately. This has 2 reasons:
1. Don't allow the UFS to continue running in PWM
2. Avoid multiple calls to pm_runtime_put_sync() when not in error
handling or power management contexts
Signed-off-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During runtime resume operation, clock scaling may get indirectly
resumed via call to ufshcd_set_dev_pwr_mode(): Start/Stop Unit command
times out and SCSI error handling ultimately calls the host reset
handler to recover, during which clock scaling is resumed. Error case
exit path of runtime resume will disable clocks. As clock scaling was
already resumed, it will get scheduled later on and try to access UFS
registers while clocks are disabled, resulting in unclocked register
access.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to UFS device specification, sense data can be only 18 bytes
long, this change makes the changes accordingly.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a write memory barrier to make sure descriptors prepared are
actually written to memory before ringing the doorbell. We have also
added the write memory barrier after ringing the doorbell register so
that controller sees the new request immediately.
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In this change there are a few fixes of possible NULL pointer access and
possible access to index that exceeds array boundaries.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In kernel we have defined specifier (%*ph[C]) to dump small buffers in a
hex format. Replace custom approach by a generic one.
Cc: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have table of the HEX characters in the kernel. Replace custom by a
generic one.
Cc: Adaptec OEM Raid Solutions <aacraid@adaptec.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the kernel we have nice specifier to print MAC by given pointer to
the address in a binary form.
Signed-off-by: Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of supplying each byte through stack let's use %pM specifier.
Cc: Hiral Patel <hiralpat@cisco.com>
Cc: Suma Ramars <sramars@cisco.com>
Acked-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch addresses the issue of driver firing DCMDs in PCI
shutdown/detach path irrespective of firmware state. Driver will now
check whether firmware is in operational state or not before firing
DCMDs. If firmware is in unrecoverable state or does not become
operational within specfied time, driver will skip firing DCMDs.
[mkp: fixed typos]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the issue of wrong PhysArm was sent to firmware for R1
VD downgrade.
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds. As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.
CC: stable@vger.kernel.org
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_release callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_assign callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_set_resp callback only ever had one implementation,
so call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_start_next callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->exch_done callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_exch_abort callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_send callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function is empty now and can be removed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->rport_flush_queue callback only ever had a single
implementation, so we can as well call it directly and
drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->rport_recv_req callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->rport_logoff callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->rport_login callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->rport_create callback only ever had a single implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Required for the next patch.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->rport_lookup callback only ever had a single implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->rport_destroy callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->exch_seq_send callback only ever had one implementation,
so we can call the function directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->lport_recv callback only ever had one implementation,
so call the function directly and remove the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->lport_reset callback only ever had one implementation,
which already is exported. So remove it and use the function
directly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'seq_els_rsp_send' callback only ever had one implementation,
so we might as well drop it and use the function directly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds code to disconnect from the client, which will make sure
any outstanding commands have been completed, before continuing on with
the remove operation.
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch changes the way the IBM vSCSI server driver manages its
Command/Response Queue (CRQ). We used to register the CRQ with phyp at
probe time. Now we wait until tpg_enable_store. Similarly, when
tpg_enable_store is called to "disable" (i.e. the stored value is 0),
we unregister the queue with phyp.
One consquence to this is that we have no need for the PART_UP_WAIT_ENAB
state, since we can't get an Init Message from the client in our CRQ if
we're waiting to be enabled, since we haven't registered the queue yet.
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch reorders functions in a manner necessary for a follow-on
patch. It also makes some minor styling changes (mostly removing extra
spaces) and fixes some typos.
There are no code changes in this patch, with one exception: due to the
reordering of the functions, I needed to explicitly declare a function
at the top of the file. However, this will be removed in the next patch,
since the code requiring the predeclaration will be removed.
Signed-off-by: Michael Cyr <mikecyr@us.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was changed to call ioport_map, which breaks platforms that
cannot provide this function:
drivers/scsi/g_NCR5380.o: In function `generic_NCR5380_init_one.constprop.0':
g_NCR5380.c:(.text.generic_NCR5380_init_one.constprop.0+0x388): undefined reference to `ioport_map'
This adds a Kconfig dependency.
Fixes: 04c40f82ccc5 ("scsi: g_NCR5380: Merge g_NCR5380 and g_NCR5380_mmio drivers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Found by 0-day robot.
Fixes: a99ac6e715bc ("scsi: fcoe: set default TC priority")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent bugfix introduced a harmless warning in the lpfc driver:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_write_firmware':
drivers/scsi/lpfc/lpfc_logmsg.h:56:45: error: format '%ld' expects argument of type 'long int', but argument 9 has type 'size_t {aka const unsigned int}' [-Werror=format=]
'size_t' is always the same width as 'long' in the kernel, but the
compiler doesn't know that. The %z modifier is what the standard expects
to be used here, and this shuts up the warning.
Fixes: 679053c651fb ("scsi: lpfc: Fix fw download on SLI-4 FC adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Any multicase address is set on all interfaces, the base interface
and any VLAN interfaces on top of this. So we might receive frames
which are not destined for us.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FIP VLAN frame consists of an ethernet header followed
by the FIP VLAN frame, so we need to skip the ethernet header
if we want to check the FIP opcode.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add additional statements for debugging FIP frames.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'enabled' sysfs attribute only accepts the values '0' and '1',
so we should error out any other values.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If DCB is not enabled or compiled in we still should be setting
a sane default priority. So put FCoE frames in priority class
'interactive' and FIP frames in priority class 'besteffort'.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We currently can only lookup the local xid, so we need
to reject REC with empty rxid.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When detecting an out-of-order sequence we should be waiting for
E_D_TOV before trying to abort the sequence.
The response might still be stuck in the queue somewhere.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we're receiving a timeout we should be checking for queue
full status; if there are still some packets pending we should
be resetting the counter to ensure we're not missing out any
packets which are still queued.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When receiving packets from the network we cannot guarantee any
frame ordering, so we should be receiving all valid frames and
let the upper layers deal with it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a sequence should be aborted the exchange might already
be completed (eg if the response is still queued in the rx
queue), so this shouldn't considered as an error.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a sequence times out we have no idea what happened to the
frame. And we do not know if we will ever receive the frame.
Hence we cannot re-use the xid as we would risk data corruption
if the xid had been re-used and the timed out frame would be
received after that.
So we need to quarantine the xid until the lport is reset.
Yes, I know this will (eventually) deplete the xid pool.
But for now it's the safest method.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cached exchange index might be invalid, in which case
we should drop down to allocate a new one.
And we should not try to access an invalid exchange when
responding to a BA_ABTS.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the queue depth is reduced we should print out the reason
for this; it might be due to a queue full condition.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Occasionally it might happen that we receive a PRLI while we're still
waiting for our PLOGI response. In that case we should return
'busy' LS status instead of 'plogi required' LS status.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PRLI is only required if the port is acting as an initiator; ports
which support target functionality only do not need to send PRLI.
At the same time the PRLI state is only used if the port initiated
a PRLI transfer; if we received a PRLI request we should _not_
change the state as this would cause our PRLI response to be dropped.
And when we receive a PRLI response we need to check if an image
pair has been established; if not the remote port cannot act as a
target for us and we need to disable target functionality.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The libfc stack generates an RTV request, so we should be implementing
an RTV responder, too.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We only ever use the 'fp' argument for fc_rport_error() to
encapsulate the error code, so we can as well do away with that
and pass the error directly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a command is aborted it might already have the DID_TIME_OUT
status set, so we shouldn't be overwriting that.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The user might want to modify the values for R_A_TOV and E_D_TOV,
so add new module parameters 'e_d_tov' and 'r_a_tov' for the
'fcoe' modules and allow to modify them via sysfs attributes.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When setting the FCP timeout we need to ensure a lower boundary
for E_D_TOV and R_A_TOV, otherwise we'd be getting spurious I/O
issues due to the fcp timer firing too early.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If fc_rport_error_retry() is attempting to retry the remote
port state we should be waiting for the configured e_d_tov
value rather than the default.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should be using the configured R_A_TOV value when sending the
exchange.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a command times out libfc is sending an REC, which also
might fail (due to frames being lost or something).
If no data has been transferred we can simply retry
the command, but the current code sets a state of FC_ERROR,
which then is being translated into DID_ERROR, resulting
in an I/O error.
So to handle this properly we need to set a separate
state FC_TRANS_RESET and mapping it onto DID_SOFT_RETRY.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 3e22760d4d.
This revert came about because of efforts by Ewan Milne, Curtis Taylor
and I. In researching this issue, significant performance issues were
seen on large CPU count systems using the software FCOE stack. Hannes
also weighed in.
The same was not apparent on much smaller low count CPU systems. The
behavior introduced by commit 3e22760d4d
lands sup with large count CPU systems seeing continual
blk_requeue_request() calls due to ML_QUEUE_HOST_BUSY.
fc_exch_alloc() used to try all the available exchange managers in the
list for an available exchange id, but this was changed in 2010 so that
if the first matched exchange manager couldn't allocate one, it fails
and we end up returning host busy. This was due to commit:
Setting the ddp_min module parameter to fcoe to 128MB prevents the
->match function from permitting the use of the offload exchange manager
for the frame, and we no longer see the problem with host busy status,
since it uses the larger non-offloaded pool.
Reverting commit 3e22760d4d was tested to
also prevent the host busy issue due to failing allocations.
Suggested-by: Ewan Milne <emilne@redhat.com>
Suggested-by: Curtis Taylor <cjt@us.ibm.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Laurence Oberman <loberman@redhat.com>
lpfc version changed to 11.2.0.2
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix fw download on SLI-4 FC adapters
Driver performs a quick validation of magic numbers in the fw
download image. Driver needed to be updated for more recent
magic numbers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Synchronize link speed with boot driver
Link speed settings set by the boot driver are reported by the hw.
Driver will attempt to read them, and if set, will respect their
values.
The driver can override the settings with its own if instructed by
user space (via bsg), with the new values being picked up by the
boot driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct panics with eh_timeout and eh_deadline
We were having double completions on our SLI-3 version of adapters.
Solved by clearing our command pointer before calling scsi_done.
The eh paths potentially ran simulatenously and would see the non-null
value and invoke scsi_done again.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix lost target in pt-to-pt connect
Change reject code to something that allows a retry
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise strings with full lpfc parameter name
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code cleanup for lpfc_sriov_nr_virtfn parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code cleanup for lpfc_max_scsicmpl_time parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code cleanup for lpfc_topology parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code cleanup for lpfc_aer_support parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code cleanup for lpfc_enable_rrq parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code clean up for lpfc_iocb_cnt parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make lpfc_prot_mask and lpfc_prot_guard per hba parameters
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set driver environment data on adapter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sg_reset on SCSI device causing kernel crash
Driver could reference stale node pointers in task mgmt call.
Changed to use resetting cmd and look up node pointer in task mgmt
function.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct embedded io wq element size. Embedded element sizes are
128 byte elements
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does a cleanup and fixes few small typos in lpfc_scsi.c
Signed-off-by: Milan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's not necessary to cast the result of kmalloc, since void pointers
are promoted to any other type. This also fixes following coccinelle
warning:
casting value returned by memory allocation function to (BIG_IOCTL_Command_struct *) is useless.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a NCR5380 host instance ends up on a shared interrupt line then
this printk will be a problem. It is already a problem on some Mac
models: when testing mac_scsi on a PowerBook 180 I found that PDMA
transfers (but not PIO transfers) cause the message to be logged.
These spurious interrupts don't appear to come from the DRQ signal from
the 5380. And they don't happen at all on the Mac LC III. A comment in
the NetBSD source code mentions this mystery. Testing seems to show
that we can safely ignore these interrupts.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Apply prototypes to get consistent function signatures for the DMA
functions implemented in the board-specific drivers. To avoid using
macros to alter actual parameters, some of those functions are reworked
slightly.
This is a step toward the goal of passing the board-specific routines
to the core driver using an ops struct (as in a platform driver or
library module).
This also helps fix some inconsistent types: where the core driver uses
ints (cmd->SCp.this_residual and hostdata->dma_len) for keeping track of
transfers, certain board-specific routines used unsigned long.
While we are fixing these function signatures, pass the hostdata pointer
to DMA routines instead of a Scsi_Host pointer, for shorter and faster
code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the call to NCR5380_poll_politely2() when possible. The call is
easily short-circuited on the PIO fast path, using the inline wrapper.
This requires that the NCR5380_read macro be made available before
any #include "NCR5380.h" so a few declarations have to be moved too.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass a NCR5380_hostdata struct pointer to the board-specific routines
instead of a Scsi_Host struct pointer. This reduces pointer chasing in
the PIO and PDMA fast paths. The old way was a mistake because it is
slow and the board-specific code is not concerned with the mid-layer.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For timeout values adopt unsigned long, which is the type of jiffies etc.
For chip register values and bit masks pass u8, which is the return type
of readb, inb etc.
For device register offsets adopt unsigned int, as it is suitable for
adding to base addresses.
Pass the NCR5380_hostdata pointer to the board-specific routines instead
of the Scsi_Host pointer. The board-specific code is concerned with
hardware and not with SCSI protocol or the mid-layer.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The various 5380 drivers inconsistently store register pointers
either in the Scsi_Host struct "legacy crap" area or in special,
board-specific members of the NCR5380_hostdata struct. Uniform
use of the latter struct makes for simpler and faster code (see
the following patches) and helps to reduce use of the
NCR5380_implementation_fields macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-order struct members so that hot data lies at the beginning of the
struct and cold data at the end. Improve the comments while we're here.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If NCR5380_poll_politely() is called under irq lock, the polling time
limit is clamped to avoid a spike in interrupt latency. When not under
irq lock, the same polling time limit acts as the worst case delay
between schedule() calls.
During PDMA (under irq lock) I've found that the 10 ms time limit is
sometimes too short, and leads to the error message,
sd 0:0:0:0: [sda] tag#1 macscsi_pread: !REQ and !ACK
This particular target identifies itself as a QUANTUM DAYTONA514S. It
seems to be slower to assert ACK than the other targets I've tested.
This patch solves the problem by increasing the polling timeout.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When polling a device register under irq lock the polling loop terminates
after a given number of jiffies. Make this timeout independent of the HZ
setting.
All 5380 drivers benefit from this patch, which optimizes the PIO fast
path, because they all use PIO transfers (for phases other than DATA IN
and DATA OUT). Some cards support only PIO transfers (even for DATA
phases). CPU cycles are scarce on some of these systems, so a small
improvement here makes a big difference.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes an old bug: accesses to device registers from the
interrupt handler (after reselection, DMA completion etc.) could mess
up a device register access elsewhere, if the latter takes place outside
of an irq lock (during selection etc.).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge the port-mapped IO and memory-mapped IO support (with the help of
ioport_map) into the g_NCR5380 module and delete g_NCR5380_mmio.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Vendor specific setup_clocks callback may require the clocks managed by
ufshcd driver to be ON. So if the vendor specific setup_clocks callback
is called while the required clocks are turned off, it could result into
unclocked register access.
To prevent possible unclock register access, this change adds one more
argument to setup_clocks callback to let it know whether it is called
pre/post the clock changes by core driver.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we haven't logged into the fabric yet we want to be a little more nuanced
with our CVL handling than what we've been:
- If the FCF has been selected, check the source MAC to make sure the frame is
from the FCF we've selected.
- If a FCF is selected and the CVL is from the FCF but we have not logged in
yet, then reset everything and go back to solicitation.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we receive an FLOGI but have already sent our own we should
not advance the state machine but rather wait for our FLOGI to
return before continuing with PLOGI.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the port is already started we don't need to login; that
will only confuse the state machine.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When fc_rport_login() is called while the rport is not
in RPORT_ST_INIT, RPORT_ST_READY, or RPORT_ST_DELETE
login is already in progress and there's no need to
drop down to FLOGI; doing so will only confuse the
other side.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an ELS response handler receives a -FC_EX_CLOSED, the rdata->rp_mutex is
already held which can lead to a deadlock condition like the following stack trace:
[<ffffffffa04d8f18>] fc_rport_plogi_resp+0x28/0x200 [libfc]
[<ffffffffa04cfa1a>] fc_invoke_resp+0x6a/0xe0 [libfc]
[<ffffffffa04d0c08>] fc_exch_mgr_reset+0x1b8/0x280 [libfc]
[<ffffffffa04d87b3>] fc_rport_logoff+0x43/0xd0 [libfc]
[<ffffffffa04ce73d>] fc_disc_stop+0x6d/0xf0 [libfc]
[<ffffffffa04ce7ce>] fc_disc_stop_final+0xe/0x20 [libfc]
[<ffffffffa04d55f7>] fc_fabric_logoff+0x17/0x70 [libfc]
The other ELS handlers need to follow the FLOGI response handler and simply do
a kref_put against the fc_rport_priv struct and exit when receving a
-FC_EX_CLOSED response.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The list of attached 'rdata' remote port structures is RCU
protected, so there is no need to take the 'disc_mutex' when
traversing it.
Rather we should be using rcu_read_lock() and kref_get_unless_zero()
to validate the entries.
We need, however, take the disc_mutex when deleting an entry;
otherwise we risk clashes with list_add.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The kref handling in fc_rport is a mess. This patch updates
the kref handling according to the following rules:
- Take a reference whenever scheduling a workqueue
- Take a reference whenever an ELS command is send
- Drop the reference at the end of the workqueue function
- Drop the reference at the end of handling ELS replies
- Take a reference when allocating an rport
- Drop the reference when removing an rport
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hip06 D03 and hip07 D05 boards have different reference clock
frequencies for the SAS controller.
Register PHY_CTRL needs to be programmed differently according to this
frequency, so add support for this.
The default register setting in PHY_CTRL is for 50MHz, so only update
this register when the refclk frequency is 66MHz.
For ACPI we expect the _RST handler to set the correct value for
PHY_CTRL (we're forced to take different approach for DT and ACPI as
ACPI does not support fixed-clock device).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trace timestamps use struct timespec and CURRENT_TIME which are not
y2038 safe. These timestamps are only part of the trace log on the
machine and are not shared with the fnic. Replace then with y2038 safe
struct timespec64 and ktime_get_real_ts64(), respectively.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Hiral Patel <hiralpat@cisco.com>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Brian Uchino <buchino@cisco.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch the ipr driver to use pci_alloc_irq_vectors. We need to two
calls to pci_alloc_irq_vectors as ipr only supports multiple MSI-X
vectors, but not multiple MSI vectors.
Otherwise this cleans up a lot of cruft and allows to use a common
request_irq loop for irq types, which happens to only iterate over a
single line in the non MSI-X case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch the arcmsr driver to use pci_alloc_irq_vectors. We need to two
calls to pci_alloc_irq_vectors as arcmsr only supports multiple MSI-X
vectors, but not multiple MSI vectors.
Otherwise this cleans up a lot of cruft and allows to use a common
request_irq loop for irq types, which happens to only iterate over a
single line in the non MSI-X case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
For blk-mq, ->nr_requests does track queue depth, at least at init
time. But for the older queue paths, it's simply a soft setting.
On top of that, it's generally larger than the hardware setting
on purpose, to allow backup of requests for merging.
Fill a hole in struct request with a 'queue_depth' member, that
drivers can call to more closely inform the block layer of the
real queue depth.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Two more important data integrity fixes related to RAID device drivers which
wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID path and a
memory leak in the scsi_debug driver
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xrlP
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two more important data integrity fixes related to RAID device drivers
which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
path and a memory leak in the scsi_debug driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices
Most blk_mq_requeue_request() and blk_mq_add_to_requeue_list() calls
are followed by kicking the requeue list. Hence add an argument to
these two functions that allows to kick the requeue list. This was
proposed by Christoph Hellwig.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since blk_mq_requeue_work() starts stopped queues and since
execution of this function can be scheduled after a queue has
been stopped it is not possible to stop queues without using
an additional state variable to track whether or not the queue
has been stopped. Hence modify blk_mq_requeue_work() such that it
does not start stopped queues. My conclusion after a review of
the blk_mq_stop_hw_queues() and blk_mq_{delay_,}kick_requeue_list()
callers is as follows:
* In the dm driver starting and stopping queues should only happen
if __dm_suspend() or __dm_resume() is called and not if the
requeue list is processed.
* In the SCSI core queue stopping and starting should only be
performed by the scsi_internal_device_block() and
scsi_internal_device_unblock() functions but not by any other
function. Although the blk_mq_stop_hw_queue() call in
scsi_queue_rq() may help to reduce CPU load if a LLD queue is
full, figuring out whether or not a queue should be restarted
when requeueing a command would require to introduce additional
locking in scsi_mq_requeue_cmd() to avoid a race with
scsi_internal_device_block(). Avoid this complexity by removing
the blk_mq_stop_hw_queue() call from scsi_queue_rq().
* In the NVMe core only the functions that call
blk_mq_start_stopped_hw_queues() explicitly should start stopped
queues.
* A blk_mq_start_stopped_hwqueues() call must be added in the
xen-blkfront driver in its blkif_recover() function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A system can get hung task timeouts if a qlogic board fails during
initialization (if the board breaks again or fails the init). The hang
involves the scsi scan.
In a nutshell, since commit beb9e315e6 ("qla2xxx: Prevent removal and
board_disable race"):
...it is possible to have freed ha (base_vha->hw) early by a call to
qla2x00_remove_one when pdev->enable_cnt equals zero:
if (!atomic_read(&pdev->enable_cnt)) {
scsi_host_put(base_vha->host);
kfree(ha);
pci_set_drvdata(pdev, NULL);
return;
Almost always, the scsi_host_put above frees the vha structure
(attached to the end of the Scsi_Host we're putting) since it's the last
put, and life is good. However, if we are entering this routine because
the adapter has broken sometime during initialization AND a scsi scan is
already in progress (and has done its own scsi_host_get), vha will not
be freed. What's worse, the scsi scan will access the freed ha structure
through qla2xxx_scan_finished:
if (time > vha->hw->loop_reset_delay * HZ)
return 1;
The scsi scan keeps checking to see if a scan is complete by calling
qla2xxx_scan_finished. There is a timeout value that limits the length
of time a scan can take (hw->loop_reset_delay, usually set to 5
seconds), but this definition is in the data structure (hw) that can get
freed early.
This can yield unpredictable results, the worst of which is that the
scsi scan can hang indefinitely. This happens when the freed structure
gets reused and loop_reset_delay gets overwritten with garbage, which
the scan obliviously uses as its timeout value.
The fix for this is simple: at the top of qla2xxx_scan_finished, check
for the UNLOADING bit in the vha structure (_vha is not freed at this
point). If UNLOADING is set, we exit the scan for this adapter
immediately. After this last reference to the ha structure, we'll exit
the scan for this adapter, and continue on.
This problem is hard to hit, but I have run into it doing negative
testing many times now (with a test specifically designed to bring it
out), so I can verify that this fix works. My testing has been against a
RHEL7 driver variant, but the bug and patch are equally relevant to to
the upstream driver.
Fixes: beb9e315e6 ("qla2xxx: Prevent removal and board_disable race")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code at the end of alua_rtpg_work() is as follows:
scsi_device_put(sdev);
kref_put(&pg->kref, release_port_group);
In other words, alua_rtpg_queue() must hold an sdev reference and a pg
reference before queueing rtpg work. If no rtpg work is queued no
additional references should be held when alua_rtpg_queue() returns. If
no rtpg work is queued, ensure that alua_rtpg_queue() only gives up the
sdev reference if that reference was obtained by the same
alua_rtpg_queue() call.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Tang Junhui <tang.junhui@zte.com.cn>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Tang Junhui <tang.junhui@zte.com.cn>
Cc: <stable@vger.kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The vmw_pvscsi driver reports most successful aborts as FAILED to the
scsi error handler. This is do to a misunderstanding of how
completion_done() works and its interaction with a successful wait using
wait_for_completion_timeout(). The vmw_pvscsi driver is expecting
completion_done() to always return true if complete() has been called on
the completion structure. But completion_done() returns true after
complete() has been called only if no function like
wait_for_completion_timeout() has seen the completion and cleared it as
part of successfully waiting for the completion.
Instead of using completion_done(), vmw_pvscsi should just use the
return value from wait_for_completion_timeout() to know if the wait
timed out or not.
[mkp: bumped driver version per request]
Signed-off-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Jim Gill <jgill@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While merging mpt3sas & mpt2sas code, we added the is_warpdrive check
condition on the wrong line
---------------------------------------------------------------------------
scsih_target_alloc(struct scsi_target *starget)
sas_target_priv_data->handle = raid_device->handle;
sas_target_priv_data->sas_address = raid_device->wwid;
sas_target_priv_data->flags |= MPT_TARGET_FLAGS_VOLUME;
- raid_device->starget = starget;
+ sas_target_priv_data->raid_device = raid_device;
+ if (ioc->is_warpdrive)
+ raid_device->starget = starget;
}
spin_unlock_irqrestore(&ioc->raid_device_lock, flags);
return 0;
------------------------------------------------------------------------------
That check should be for the line sas_target_priv_data->raid_device =
raid_device;
Due to above hunk, we are not initializing raid_device's starget for
raid volumes, and so during raid disk deletion driver is not calling
scsi_remove_target() API as driver observes starget field of
raid_device's structure as NULL.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: 7786ab6aff ("mpt3sas: Ported WarpDrive product SSS6200 support")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reference count of pg leaks in alua_rtpg_work() since kref_put() is not
called to decrease the reference count of pg when the condition
pg->rtpg_sdev==NULL satisfied (actually it is easy to satisfy), it would
cause memory of pg leakage.
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Cc: <stable@vger.kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we don't need the common flags to overflow outside the range
of a 32-bit type we can encode them the same way for both the bio and
request fields. This in addition allows us to place the operation
first (and make some room for more ops while we're at it) and to
stop having to shift around the operation values.
In addition this allows passing around only one value in the block layer
instead of two (and eventuall also in the file systems, but we can do
that later) and thus clean up a lot of code.
Last but not least this allows decreasing the size of the cmd_flags
field in struct request to 32-bits. Various functions passing this
value could also be updated, but I'd like to avoid the churn for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two small fixes: one is a fatal section mismatch (reference to init after it's
discarded) and the other two are iscsi locking fixes.
Signed-off-by: James E. J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BI5E
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes: one is a fatal section mismatch (reference to init
after it's discarded) and the other two are iscsi locking fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: NCR5380: no longer mark irq probing as __init
scsi: be2iscsi: Replace _bh with _irqsave/irqrestore
scsi: libiscsi: Fix locking in __iscsi_conn_send_pdu
The arcmsr driver failed to pass SYNCHRONIZE CACHE to controller
firmware. Depending on how drive caches are handled internally by
controller firmware this could potentially lead to data integrity
problems.
Ensure that cache flushes are passed to the controller.
[mkp: applied by hand and removed unused vars]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
map_storep was not being vfree()'d in the module_exit call.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If sd_zbc_report_zones fails, the check for 'zone_blocks == 0'
later in the function accesses uninitialized data:
drivers/scsi/sd_zbc.c: In function ‘sd_zbc_read_zones’:
drivers/scsi/sd_zbc.c:520:7: error: ‘zone_blocks’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This sets it to zero, which has the desired effect of leaving
the sd_zbc_read_zones successfully with sdkp->zone_blocks = 0.
Fixes: 89d9475610 ("sd: Implement support for ZBC devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 02b01e010a ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010a
CC: stable@vger.kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Five small fixes. Some of these, like the nested spinlock overwriting saved
flags and the Kasan use after free look serious, but they seem not to have
been picked up in testing or seen in the field. The biggest user visible
issue is probably the wrong device handler for Clariion, which means that alua
doesn't bind to the array like it should.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nB7G
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five small fixes.
Some of these, like the nested spinlock overwriting saved flags and
the Kasan use after free look serious, but they seem not to have been
picked up in testing or seen in the field.
The biggest user visible issue is probably the wrong device handler
for Clariion, which means that alua doesn't bind to the array like it
should"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: Fix async error WARN_ON
scsi: zfcp: spin_lock_irqsave() is not nestable
scsi: Remove one useless stack variable
scsi: Fix use-after-free
scsi: Replace wrong device handler name for CLARiiON arrays
Merge the gup_flags cleanups from Lorenzo Stoakes:
"This patch series adjusts functions in the get_user_pages* family such
that desired FOLL_* flags are passed as an argument rather than
implied by flags.
The purpose of this change is to make the use of FOLL_FORCE explicit
so it is easier to grep for and clearer to callers that this flag is
being used. The use of FOLL_FORCE is an issue as it overrides missing
VM_READ/VM_WRITE flags for the VMA whose pages we are reading
from/writing to, which can result in surprising behaviour.
The patch series came out of the discussion around commit 38e0885465
("mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing"),
which addressed a BUG_ON() being triggered when a page was faulted in
with PROT_NONE set but having been overridden by FOLL_FORCE.
do_numa_page() was run on the assumption the page _must_ be one marked
for NUMA node migration as an actual PROT_NONE page would have been
dealt with prior to this code path, however FOLL_FORCE introduced a
situation where this assumption did not hold.
See
https://marc.info/?l=linux-mm&m=147585445805166
for the patch proposal"
Additionally, there's a fix for an ancient bug related to FOLL_FORCE and
FOLL_WRITE by me.
[ This branch was rebased recently to add a few more acked-by's and
reviewed-by's ]
* gup_flag-cleanups:
mm: replace access_process_vm() write parameter with gup_flags
mm: replace access_remote_vm() write parameter with gup_flags
mm: replace __access_remote_vm() write parameter with gup_flags
mm: replace get_user_pages_remote() write/force parameters with gup_flags
mm: replace get_user_pages() write/force parameters with gup_flags
mm: replace get_vaddr_frames() write/force parameters with gup_flags
mm: replace get_user_pages_locked() write/force parameters with gup_flags
mm: replace get_user_pages_unlocked() write/force parameters with gup_flags
mm: remove write/force parameters from __get_user_pages_unlocked()
mm: remove write/force parameters from __get_user_pages_locked()
mm: remove gup_flags FOLL_WRITE games from __get_user_pages()
Implement ZBC support functions to setup zoned disks, both
host-managed and host-aware models. Only zoned disks that satisfy
the following conditions are supported:
1) All zones are the same size, with the exception of an eventual
last smaller runt zone.
2) For host-managed disks, reads are unrestricted (reads are not
failed due to zone or write pointer alignement constraints).
Zoned disks that do not satisfy these 2 conditions are setup with
a capacity of 0 to prevent their use.
The function sd_zbc_read_zones, called from sd_revalidate_disk,
checks that the device satisfies the above two constraints. This
function may also change the disk capacity previously set by
sd_read_capacity for devices reporting only the capacity of
conventional zones at the beginning of the LBA range (i.e. devices
reporting rc_basis set to 0).
The capacity message output was moved out of sd_read_capacity into
a new function sd_print_capacity to include this eventual capacity
change by sd_zbc_read_zones. This new function also includes a call
to sd_zbc_print_zones to display the number of zones and zone size
of the device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: * Removed zone cache support
* Removed mapping of discard to reset write pointer command
* Modified sd_zbc_read_zones to include checks that the
device satisfies the kernel constraints
* Implemeted REPORT ZONES setup and post-processing based
on code from Shaun Tancheff <shaun.tancheff@seagate.com>
* Removed confusing use of 512B sector units in functions
interface]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This removes the 'write' and 'force' use from get_user_pages_unlocked()
and replaces them with 'gup_flags' to make the use of FOLL_FORCE
explicit in callers as use of this flag can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The g_NCR5380 has been converted to more regular probing, which
means its probe function can now be invoked after the __init section
is discarded, as pointed out by this kbuild warning:
WARNING: drivers/scsi/built-in.o(.text+0x3a105): Section mismatch in reference from the function generic_NCR5380_isa_match() to the function .init.text:probe_intr()
WARNING: drivers/scsi/built-in.o(.text+0x3a145): Section mismatch in reference from the function generic_NCR5380_isa_match() to the variable .init.data:probe_irq
To make sure this works correctly in all cases, let's remove
the __init and __initdata annotations.
Fixes: a8cfbcaec0 ("scsi: g_NCR5380: Stop using scsi_module.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code at free_task label in __iscsi_conn_send_pdu can get executed
from blk_timeout_work which takes queue_lock using spin_lock_irq.
back_lock taken with spin_unlock_bh will cause WARN_ON_ONCE. The code
gets executed either with bottom half or IRQ disabled hence using
spin_lock/spin_unlock for back_lock is safe.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is just a set of minor updates and fixes which weren't quite ready in
time for the first pull request. The only real thing of note is Mike Christie
is stepping down as Maintainer of iscsi to be replaced by Lee Duncan and Chris
Leech.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=bAub
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a set of minor updates and fixes which weren't quite
ready in time for the first pull request.
The only real thing of note is Mike Christie is stepping down as
Maintainer of iscsi to be replaced by Lee Duncan and Chris Leech"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Kconfig fix
scsi: g_NCR5380: Stop using scsi_module.c
scsi: g_NCR5380: Reduce overrides[] from array to struct
scsi: g_NCR5380: Remove deprecated __setup
scsi: ufs: Fix error return code in ufshcd_init()
scsi: ufs: Data Segment only needed for WRITE DESCRIPTOR
scsi: cxgb4i: Set completion bit in work request
MAINTAINERS: Update open-iscsi maintainers
scsi: ufs: Enable no vccq quirk for skhynix device
scsi: be2iscsi: mark symbols static where possible
The local variable of 'devname' in scsi_report_lun_scan() isn't used any
more, so remove it.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At drivers/scsi/device_handler/scsi_dh_emc.c it was defined as:
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: device-mapper development <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull blk-mq irq/cpu mapping updates from Jens Axboe:
"This is the block-irq topic branch for 4.9-rc. It's mostly from
Christoph, and it allows drivers to specify their own mappings, and
more importantly, to share the blk-mq mappings with the IRQ affinity
mappings. It's a good step towards making this work better out of the
box"
* 'for-4.9/block-irq' of git://git.kernel.dk/linux-block:
blk_mq: linux/blk-mq.h does not include all the headers it depends on
blk-mq: kill unused blk_mq_create_mq_map()
blk-mq: get rid of the cpumask in struct blk_mq_tags
nvme: remove the post_scan callout
nvme: switch to use pci_alloc_irq_vectors
blk-mq: provide a default queue mapping for PCI device
blk-mq: allow the driver to pass in a queue mapping
blk-mq: remove ->map_queue
blk-mq: only allocate a single mq_map per tag_set
blk-mq: don't redistribute hardware queues on a CPU hotplug event
This update includes the usual round of major driver updates (hpsa, be2iscsi,
hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa called smartpqi
for which a driver is added, there's some cleanup work of the ibm vscsi target
and updates to libfc, plus a whole host of minor fixes and updates and finally
the removal of several ISA drivers which seem not to have been used for years.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cyTO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (hpsa,
be2iscsi, hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa
called smartpqi for which a driver is added, there's some cleanup work
of the ibm vscsi target and updates to libfc, plus a whole host of
minor fixes and updates and finally the removal of several ISA drivers
which seem not to have been used for years"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (173 commits)
scsi: mvsas: Mark symbols static where possible
scsi: pm8001: Mark symbols static where possible
scsi: arcmsr: Simplify user_len checking
scsi: fcoe: fix off by one in eth2fc_speed()
scsi: dtc: remove from tree
scsi: t128: remove from tree
scsi: pas16: remove from tree
scsi: u14-34f: remove from tree
scsi: ultrastor: remove from tree
scsi: in2000: remove from tree
scsi: wd7000: remove from tree
scsi: scsi_dh_alua: Fix memory leak in alua_rtpg()
scsi: lpfc: Mark symbols static where possible
scsi: hpsa: correct call to hpsa_do_reset
scsi: ufs: Get a TM service response from the correct offset
scsi: ibmvfc: Fix I/O hang when port is not mapped
scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up
scsi: ipr: Remove redundant messages at adapter init time
scsi: ipr: Don't log unnecessary 9084 error details
scsi: smartpqi: raid bypass lba calculation fix
...
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
One final fix before 4.8: there's a memory leak triggered by turning scsi mq
off due to the fact that we assume on host release that the already running
hosts weren't mq based because that's the state of the global flag (even
though they were), so fix it by tracking this on a per host host basis.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=awzl
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One final fix before 4.8.
There was a memory leak triggered by turning scsi mq off due to the
fact that we assume on host release that the already running hosts
weren't mq based because that's the state of the global flag (even
though they were).
Fix it by tracking this on a per host host basis"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Avoid that toggling use_blk_mq triggers a memory leak
Currently if we have PCI and UFSHCD configured in the kernel, both
SCSI_UFS_DWC_TC_PCI and SCSI_UFSHCD_PCI show up, which is not correct.
This patch changes the UFS Kconfig to assure hierarchy between the 2
options.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert g_NCR5380 to use scsi_add_host instead of scsi_module.c Use
pnp_driver and isa_driver to manage cards.
In order to support multiple cards, new module parameter format is
introduced. The old parameters are kept for compatibility.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove compile-time card type definition GENERIC_NCR5380_OVERRIDE. Then
remove all code iterating the overrides[] array and reduce it to struct
card.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove deprecated __setup for parsing command line parameters.
g_NCR5380.* parameters could be used instead.
This might break existing setups with g_NCR5380 built-in (if there are
any). But it has to go in order to remove the overrides[] array.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some devices have problems handling a Query UPIU with Data Segment
set. Only set it for WRITE DESCRIPTOR commands.
[mkp: updated patch description]
Signed-off-by: Zang Leigang <zangleigang@hisilicon.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SKCBF_TX_FLAG_COMPL flag is set and unacknowledged credits are >= max
credits / 2, set completion bit in work request to reclaim credits.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch enable no vccq quirk for SKHynix devices. SKHynix ufs device
don't need vccq vrail for device operation.
Signed-off-by: Kyuho Choi <kyuho.choi@sk.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 6 warnings when building kernel with W=1:
drivers/scsi/be2iscsi/be_main.c:65:1: warning: no previous prototype for 'beiscsi_log_enable_disp' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:78:1: warning: no previous prototype for 'beiscsi_log_enable_change' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:97:1: warning: no previous prototype for 'beiscsi_log_enable_store' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:116:1: warning: no previous prototype for 'beiscsi_log_enable_init' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:4587:5: warning: no previous prototype for 'beiscsi_iotask_v2' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:4976:6: warning: no previous prototype for 'beiscsi_hba_attrs_init' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Jitendra Bhivare <Jitendra.bhivare@broadcom>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/mvsas/mv_sas.c:77:18: warning: no previous prototype for 'mvs_find_dev_mvi' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:105:5: warning: no previous prototype for 'mvs_find_dev_phyno' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1161:20: warning: no previous prototype for 'mvs_alloc_dev' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1178:6: warning: no previous prototype for 'mvs_free_dev' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1188:5: warning: no previous prototype for 'mvs_dev_found_notify' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1244:6: warning: no previous prototype for 'mvs_dev_gone_notify' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1614:6: warning: no previous prototype for 'mvs_set_sense' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1653:6: warning: no previous prototype for 'mvs_fill_ssp_resp_iu' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_64xx.c:139:6: warning: no previous prototype for 'mvs_64xx_clear_srs_irq' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_64xx.c:566:6: warning: no previous prototype for 'mvs_64xx_make_prd' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 2 warnings when building kernel with W=1:
drivers/scsi/pm8001/pm8001_sas.c:530:23: warning: no previous prototype for 'pm8001_alloc_dev' [-Wmissing-prototypes]
drivers/scsi/pm8001/pm8001_hwi.c:4495:5: warning: no previous prototype for 'pm8001_chip_phy_stop_req' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do the user_len check first and then the ver_addr allocation so that we
can save us the kfree() on the error path when user_len is >
ARCMSR_API_DATA_BUFLEN.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Marco Grassi <marco.gra@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Tomas Henzl <thenzl@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the following memory leak is triggered if
use_blk_mq is disabled after a SCSI host has been allocated by the
ib_srp driver and before the same SCSI host is freed:
unreferenced object 0xffff8803a168c568 (size 256):
backtrace:
[<ffffffff81620c95>] kmemleak_alloc+0x45/0xa0
[<ffffffff811bb104>] __kmalloc_node+0x1e4/0x400
[<ffffffff81309fe4>] blk_mq_alloc_tag_set+0xb4/0x230
[<ffffffff814731b7>] scsi_mq_setup_tags+0xc7/0xd0
[<ffffffff81469c26>] scsi_add_host_with_dma+0x216/0x2d0
[<ffffffffa064bef5>] srp_create_target+0xe55/0x13d0 [ib_srp]
[<ffffffff8143ce23>] dev_attr_store+0x13/0x20
[<ffffffff8125f030>] sysfs_kf_write+0x40/0x50
[<ffffffff8125e397>] kernfs_fop_write+0x137/0x1c0
[<ffffffff811d8c13>] __vfs_write+0x23/0x140
[<ffffffff811d92e0>] vfs_write+0xb0/0x190
[<ffffffff811da5b4>] SyS_write+0x44/0xa0
[<ffffffff8162c8a5>] entry_SYSCALL_64_fastpath+0x18/0xa8
Fixes: 9aa9cc4221 ("scsi: remove the disable_blk_mq host flag")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should be "< ARRAY_SIZE()" instead of "<= ARRAY_SIZE()".
Fixes: 0b924e5505 ("scsi: fcoe: provide translation table between Ethernet and FC port speeds")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
buff should be freed before returning with SCSI_DH_RETRY in alua_rtpg().
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/lpfc/lpfc_sli.c:5693:1: warning: no previous prototype for 'lpfc_set_features' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:8972:1: warning: no previous prototype for 'lpfc_sli_calc_ring' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4621:1: warning: no previous prototype for 'lpfc_rdp_res_link_service' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4633:1: warning: no previous prototype for 'lpfc_rdp_res_sfp_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4698:1: warning: no previous prototype for 'lpfc_rdp_res_link_error' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4727:1: warning: no previous prototype for 'lpfc_rdp_res_bbc_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4752:1: warning: no previous prototype for 'lpfc_rdp_res_oed_temp_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4780:1: warning: no previous prototype for 'lpfc_rdp_res_oed_voltage_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4809:1: warning: no previous prototype for 'lpfc_rdp_res_oed_txbias_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4838:1: warning: no previous prototype for 'lpfc_rdp_res_oed_txpower_desc' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
calling fill_cmd() using a MACRO definition not handled in switch
statement causes BUG() to be called.
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When any UFS host controller receives a TM(Task Management) response
from a UFS device, UFS driver has been recognize like receiving a
message of "Task Management Function Complete"(00h) in all cases, so
far. That means there is no pending task for a tag of the TM request
sent before in the UFS device. That's because the byte offset 6 in TM
response which has been used to get a TM service response so far
represents just whether or not a TM transmission passes.
Regarding UFS spec, the correct byte offset to get TM service response
is 15, not 6.
I tested that UFS driver responds properly for the TM response from a
UFS device with an reference board with exynos8890, as follow: No
pending task -> Task Management Function Complete (00h) Pending task ->
Task Management Function Succeeded (08h)
[mkp: applied by hand]
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: HeonGwang Chu <hg.chu@samsung.com>
Tested-by: : Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a VFC port gets unmapped in the VIOS, it may not respond with a CRQ
init complete following H_REG_CRQ. If this occurs, we can end up having
called scsi_block_requests and not a resulting unblock until the init
complete happens, which may never occur, and we end up hanging I/O
requests. This patch ensures the host action stay set to
IBMVFC_HOST_ACTION_TGT_DEL so we move all rports into devloss state and
unblock unless we receive an init complete.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Install the callbacks via the state machine. It uses the multi instance
infrastructure of the hotplug code to handle each interface.
virtscsi_set_affinity() is removed from virtscsi_init() because
virtscsi_cpu_notif_add() (the function which registers the instance) is invoked
right after it and the cpuhp_state_add_instance() functions invokes the startup
callback on all online CPUs.
The same thing can not be applied virtscsi_cpu_notif_remove() because
virtscsi_remove_vqs() invokes virtscsi_set_affinity() with affinity = false as
argument but the old CPU_DEAD state invoked the function with affinity = true
(which does not match the DEAD callback).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: virtualization@lists.linux-foundation.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160906170457.32393-11-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We get a few warnings when building kernel with W=1:
drivers/scsi/megaraid/megaraid_sas_fusion.c:281:1: warning: no previous prototype for 'megasas_free_cmds_fusion' [-Wmissing-prototypes]
drivers/scsi/megaraid/megaraid_sas_fusion.c:714:1: warning: no previous prototype for 'megasas_ioc_init_fusion' [-Wmissing-prototypes]
....
In fact, these functions are declared in
drivers/scsi/megaraid/megaraid_sas_base.c, but should be declared in a
header file, thus can be recognized in other file.
So this patch adds the declarations into
drivers/scsi/megaraid/megaraid_sas_fusion.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever multiple HRRQs are enabled, which is the default setting now,
we end up seeing the following message logged prior to initialization of
each HRRQ:
Starting IOA initialization sequence
This results in 16 of these messages on most adapters, which serves
little purpose. Change to just log this once.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A 9084 error gets logged by the ipr adapter when adapter raw mode gets
enabled. A bunch of unformatted hex data also gets logged for this
error, which is of little use, so let's avoid logging it by default in
order to avoid the log getting polluted with useless data.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the ioaccel path, the calculation of the starting LBA for
READ(6)/WRITE(6) SCSI commands does not take into account the most
significant 5 bits of the LBA: it only uses the least significant 16
bits of the starting LBA.
Reported-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Missing 5 bits of byte 1 in the LBA issued by SML.
Reported-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mkp: applied by hand]
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers use the default, so provide an inline version of it. If we
ever need other queue mapping we can add an optional method back,
although supporting will also require major changes to the queue setup
code.
This provides better code generation, and better debugability as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We need to put an upper bound on "user_len" so the memcpy() doesn't
overflow.
Cc: <stable@vger.kernel.org>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix to return error code -ENOMEM from the dma mapping error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These should go together with the rest of the T10 protection information
defintions.
[mkp: s/T10_DIF/T10_PI/]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of defining a local version of it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And remove the declaration of the latter in sd.h as scsi_debug was the
only user.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benest@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benest@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before using vendor-specific VPD pages for getting raid_level and
device_id, check for page support. If page isn't supported, don't try
to use it. Also, pay attention to return status on hpsa_get_device_id.
[mkp: fix boolean return warnings reported by kbuild test robot]
Reviewed-by: Scott Benesh <scott.benest@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A device can be deleted causing NULL pointer issues.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we are checking for external status before we are determining
if a device is an external device.
Reviewed-by: Scott Benesh <scott.benest@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large PIO transfers are broken up into chunks to try to avoid disabling
local IRQs for long periods. But IRQs are still disabled for too long
and this causes SCC FIFO overruns during serial port transfers.
This patch reduces the PIO chunk size to reduce interrupt latency to
something on the order of milliseconds, at the expense of additional CPU
overhead from extra iterations of the NCR5380_main() loop.
That CPU overhead is a problem for slow machines (e.g. mac_scsi on 25
MHz 68030) but these machines generally use PDMA not PIO. This patch
doesn't make the overhead any worse on my Mac LC III (because it only
gets about 510 accesses per ms).
This patch decreases disk performance by a fraction of one percent for
dmx3191d on my 333 MHz PowerPC 750. Other affected hardware (such as
g_NCR5380 on x86) was not tested but 5380 ISA cards generally use PDMA
and not PIO.
[mkp: fix whitespace]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
The usage pattern of the completion is:
waiter context waker context
virtscsi_tmf()
DECLARE_COMPLETION_ONSTACK()
virtscsi_kick_cmd()
wait_for_completion()
virtscsi_complete_free()
complete()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
The usage pattern of the completion is:
waiter context waker context
sym_eh_handler()
struct completion eh_done
init_completion(eh_done)
pci_channel_offline()
wait_for_completion_timeout(eh_done)
sym2_io_resume()
complete(eh_done)
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The (re)initializing of the completion object should be done before we
trigger the transfer. Doing this after triggering the hardware opens up
a race window. Without the timeout we would problaly even deadlock. Use
also reinit_completion because we initalize the whole data structure in
csio_scscim_init().
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
The usage pattern of the completion is:
waiter context waker context
csio_eh_abort_handler()
reinit_completion()
wait_for_completion_timeout()
csio_scsi_err_handler()
complete()
[mkp: fix typo]
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A dev_printk message spans two lines and the literal string is missing a
white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the v2 hw is attached with many disks through an expander, there
may be OOB reset resulting in a PHY going down after the speed is
negotiated (very low probability).
This issue is resolved by modifying the link control registers to send
three identify frames before the PHY is ready (according to 6.10.3.3.2
in SAS 3.0 spec) and close ready when the PHY is down.
Signed-off-by: NengLong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In setup_itct_v2_hw(), SATA device type SAS_SATA_PENDING is missing, so
add it.
Note: The HiSi SAS controller does not support SATA PM, so do not handle
SAS_SATA_PM_PORT or SAS_SATA_PM.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function config_id_frame_v1_hw() is called twice for each PHY during
initialisation, which is unneeded.
So remove init_id_frame_v1_hw(), which only calls
config_id_frame_v1_hw().
We will keep the call to config_id_frame_v1_hw() in start_phy_v1_hw()
since it will be used for PHY reset functions.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function config_id_frame_v2_hw() is called twice for each PHY during
initialisation, which is unneeded.
So remove init_id_frame_v2_hw(), which only calls
config_id_frame_v2_hw().
We will keep the call to config_id_frame_v2_hw() in start_phy_v2_hw()
since it will be used for PHY reset functions.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The endianness for the SAS address in the TX_ID_DWORD registers is set
incorrectly. We see errors like this in the boot log for v2 hw (which
would have the same issue as v1 hw):
[ 7.583284] sas: target proto 0x0 at 50000d1108e7923f:0x1f not handled
This is due to the host SAS addr not matching the PHY SAS addr in the
expander host-attached phy discovery responses.
To fix, we byte swap the SAS addr from BE to LE (which is the endianness
of the SAS controller).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The endianness for the SAS address in the TX_ID_DWORD registers is set
incorrectly. We see errors like this in the boot log:
[ 7.583284] sas: target proto 0x0 at 50000d1108e7923f:0x1f not handled
This is due to the host SAS addr not matching the PHY SAS addr in the
expander host-attached phy discovery responses.
To fix, we byte swap the SAS addr from BE to LE (which is the endianness
of the SAS controller).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The device DMA mask was being set after the bulk of the DMA allocations
in the driver init, so potentially DMA allocates fail. To resolve,
relocate before allocating the DMA memory when initialising the driver.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If hisi_sas_task_prep() fails for a SATA device due to PHY down, we
return a failure to libata and also call task_done(), which will cause
ata_qc_complete() to be called twice: - first call from
hisi_sas_task_prep(), which will clear flag ATA_QCFLAG_ACTIVE -
ata_qc_complete() called from libata The warning call trace is as
follows:
[ 117.070206] [<ffff0000084f59b0>] __ata_qc_complete+0xf4/0x11c
[ 117.070208] [<ffff0000084f5b58>] ata_qc_complete+0x180/0x200
[ 117.070210] [<ffff0000084f5dd0>] ata_qc_issue+0x110/0x354
[ 117.070212] [<ffff0000084f6254>] ata_exec_internal_sg+0x240/0x4d0
[ 117.070214] [<ffff0000084f6544>] ata_exec_internal+0x60/0xa0
[ 117.070217] [<ffff000008501580>] ata_read_log_page+0x188/0x1b4
[ 117.070218] [<ffff0000085017dc>] ata_eh_analyze_ncq_error+0xa8/0x274
[ 117.070220] [<ffff000008501a3c>] ata_eh_link_autopsy+0x94/0x8c8
[ 117.070222] [<ffff0000085022a4>] ata_eh_autopsy+0x34/0xe8
[ 117.070223] [<ffff00000850540c>] ata_do_eh+0x28/0xc0
[ 117.070225] [<ffff0000085054e0>] ata_std_error_handler+0x3c/0x84
[ 117.070227] [<ffff000008505140>] ata_scsi_port_error_handler+0x480/0x674
[ 117.070230] [<ffff0000084e3020>] async_sas_ata_eh+0x44/0x78
[ 117.070231] [<ffff0000080d6b8c>] async_run_entry_fn+0x40/0x104
[ 117.070234] [<ffff0000080ce518>] process_one_work+0x128/0x2f0
[ 117.070235] [<ffff0000080ce738>] worker_thread+0x58/0x434
[ 117.070237] [<ffff0000080d416c>] kthread+0xd4/0xe8
[ 117.070240] [<ffff000008084e10>] ret_from_fork+0x10/0x40
The issue is resolved by simply returning a failure status code to the
upper layer.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function phy_up_v2_hw(), we needlessly recalculate the phy linkrate
for all phys, and the calculation is incorrect for phy8, so remove this
code.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Delivery queue enable register should only be written to once at
reset for v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The memory calculation for the tags bitmap should use BITS_PER_BYTE
macro instead of coincidental same value of sizeof(unsigned long).
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the slot memory is zeroed when it is freed and also when it is
reused, like in hisi_sas_task_prep(). Optimise by avoiding the redundant
zeroing in the free.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
None of the CHL_INT2 interrupts are serviced in the channel irq ISR, so
leave the interrupt source masked. The interrupt mask is initially set
in init_reg_v2_hw().
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimise by saving an avoidable read in the get_free_slot function. The
delivery queue write pointer will only be updated by software, so don't
bother re-reading what was already written in the previous call to
start_delivery function.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimise by saving an avoidable read in the cq interrupt. The queue
read pointer will only be updated by software, so don't bother
re-reading what was already written in the previous interrupt.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 888baf069f ("scsi: cxlflash: Add kref to context") introduced a
kref to the context. In particular, the detach routine was updated to
use the kref services for managing the removal and destruction of a
context.
As part of this change, the tracking mechanism internal to the detach
handler was refactored. This introduced a bug that can cause the
tracking state to be lost. This can lead to a situation where exclusive
access to a context is prematurely [and unknowingly] relinquished for
the executing thread.
To remedy, only update the tracking state when the kref operation
indicates the context was removed.
Fixes: 888baf069f ("scsi: cxlflash: Add kref to context")
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 964497b3bf ("cxlflash: Remove dual port online dependency")
logically removed the ability for the WWPN setup routine afu_set_wwpn()
to return a non-success value. This routine can safely be made a void to
simplify the code as there is no longer a need to report a failure.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an EEH occurs during device initialization, the port timeout logic
can cause excessive delays as MMIO reads will fail. Depending on where
they are experienced, these delays can lead to a prolonged reset,
causing an unnecessary triggering of other timeout logic in the SCSI
stack or user applications.
To expedite recovery, the port timeout logic is updated to decay the
timeout at a much faster rate when in the presence of a likely EEH
frozen event.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The EEH reset handler is ignorant to the current state of the driver
when processing a frozen event and initiating a device reset. This can
be an issue if an EEH event occurs while a user or stack initiated reset
is executing. More specifically, if an EEH occurs while the SCSI host
reset handler is active, the reset initiated by the EEH thread will
likely collide with the host reset thread. This can leave the device in
an inconsistent state, or worse, cause a system crash.
As a remedy, the EEH handler is updated to evaluate the device state and
take appropriate action (proceed, wait, or disconnect host). The host
reset handler is also updated to handle situations where an EEH occurred
during a host reset. In such situations, the host reset handler will
delay reporting back a success to give the EEH reset an opportunity to
complete.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 704c4b0ddc ("cxlflash: Shutdown notify support for CXL Flash
cards") was recently introduced to notify the AFU when a system is going
down. Due to the position of the cxlflash driver in the device stack,
cxlflash devices are _always_ removed during a reboot/shutdown. This can
lead to a crash if the cxlflash shutdown hook is invoked _after_ the
shutdown hook for the owning virtual PHB. Furthermore, the current
implementation of shutdown/remove hooks for cxlflash are not tolerant to
being invoked when the device is not enabled. This can also lead to a
crash in situations where the remove hook is invoked after the device
has been removed via the vPHBs shutdown hook. An example of this
scenario would be an EEH reset failure while a reboot/shutdown is in
progress.
To solve both problems, the shutdown hook for cxlflash is updated to
simply remove the device. This path already includes the AFU
notification and thus this solution will continue to perform the
original intent. At the same time, the remove hook is updated to protect
against being called when the device is not enabled.
Fixes: 704c4b0ddc ("cxlflash: Shutdown notify support for CXL Flash
cards")
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a port link is established, the AFU sends a 'link up' interrupt.
After the link is up, corresponding initialization steps are performed
on the card. Following that, when the card is ready for I/O, the AFU
sends 'login succeeded' interrupt. Today, cxlflash invokes
scsi_scan_host() upon receipt of both interrupts.
SCSI commands sent to the port prior to the 'login succeeded' interrupt
will fail with 'port not available' error. This is not desirable.
Moreover, when async_scan is active for the host, subsequent scan calls
are terminated with error. Due to this, the scsi_scan_host() call
performed after 'login succeeded' interrupt could portentially return
error and the devices may not be scanned properly.
To avoid this problem, scsi_scan_host() should be called only after the
'login succeeded' interrupt.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I modified a string as described in UFS spec as follow: umpcrs -> upmcrs.
[mkp: applied by hand]
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/bnx2fc/bnx2fc_els.c:257:6: warning: no previous prototype for 'bnx2fc_srr_compl' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_els.c:367:6: warning: no previous prototype for 'bnx2fc_rec_compl' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:628:5: warning: no previous prototype for 'bnx2fc_percpu_io_thread' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:1413:26: warning: no previous prototype for 'bnx2fc_interface_create' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_hwi.c:997:21: warning: no previous prototype for 'bnx2fc_alloc_work' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_io.c:1082:5: warning: no previous prototype for 'bnx2fc_abts_cleanup' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. so this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 1 warning when building kernel with W=1:
drivers/scsi/aacraid/src.c:616:5: warning: no previous prototype for 'aac_src_select_comm' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static. so this patch
marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling 'list_splice' followed by 'INIT_LIST_HEAD' is equivalent to
'list_splice_init'.
This has been spotted with the following coccinelle script:
/////
@@
expression y,z;
@@
- list_splice(y,z);
- INIT_LIST_HEAD(y);
+ list_splice_init(y,z);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is really three fixes, but the SES one comes in a bundle of three
(making the replacement API available properly, using it and removing
the non-working one). The SES problem causes an oops on hpsa devices
because they attach virtual disks to the host which aren't SAS
attached (the replacement API ignores them). The other two fixes are
fairly minor: the sense key one means we actually resolve a newly
added sense key and the RDAC device blacklisting is needed to prevent
us annoying the universal XPORT lun of various RDAC arrays.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HBmE
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is really three fixes, but the SES one comes in a bundle of three
(making the replacement API available properly, using it and removing
the non-working one). The SES problem causes an oops on hpsa devices
because they attach virtual disks to the host which aren't SAS
attached (the replacement API ignores them).
The other two fixes are fairly minor: the sense key one means we
actually resolve a newly added sense key and the RDAC device
blacklisting is needed to prevent us annoying the universal XPORT lun
of various RDAC arrays"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sas: remove is_sas_attached()
scsi: ses: use scsi_is_sas_rphy instead of is_sas_attached
scsi: sas: provide stub implementation for scsi_is_sas_rphy
scsi: blacklist all RDAC devices for BLIST_NO_ULD_ATTACH
scsi: fix upper bounds check of sense key in scsi_sense_key_string()
We get 2 warnings when build kernel with W=1:
drivers/scsi/ufs/tc-dwc-g210.c:261:5: warning: no previous prototype for 'tc_dwc_g210_config_40_bit' [-Wmissing-prototypes]
drivers/scsi/ufs/tc-dwc-g210.c:293:5: warning: no previous prototype for 'tc_dwc_g210_config_20_bit' [-Wmissing-prototypes]
In fact, these functions are declared in ufs/tc-dwc-g210.h, so this
patch add missing header dependencies
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sr_pm_ops, of type struct dev_pm_ops, is never modified, so declare it
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 4 warnings about global functions without a declaration
in the scsi pmcraid driver when building with W=1:
drivers/scsi/pmcraid.c:309:6: warning: no previous prototype for 'pmcraid_init_cmdblk' [-Wmissing-prototypes]
drivers/scsi/pmcraid.c:404:6: warning: no previous prototype for 'pmcraid_return_cmd' [-Wmissing-prototypes]
drivers/scsi/pmcraid.c:1713:6: warning: no previous prototype for 'pmcraid_ioasc_logger' [-Wmissing-prototypes]
drivers/scsi/pmcraid.c:3141:1: warning: no previous prototype for 'pmcraid_init_ioadls' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which it is
declared and don't need a declaration, but can be made static. so this
patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SUPPORTED_FORMATS is 1 << 1 so it's never zero.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mkp: applied by hand]
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently doesn't properly deregisters target sessions
completely, so this will address that.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mkp: fixed typo]
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The aacraid driver will not managage Microsemi smartpqi controllers, but
will still manage older aacraid devices.
Updated help section.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some cache flush operations can take longer than the timeout value. Best
to not impose a time limit to handle all cases.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
minor cleanup of scsi queue command function
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
minor tweaks to update time support
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
reformatted pqi_num_elements_free() to match the rest of the driver
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
the driver no longer waits for the firmware to consume
the event ack IU.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 6c223761e 'smartpqi: initial commit of Microsemi smartpqi driver'
Fixed a bug where the driver would not free all of the
controller resources if the controller ever went offline.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Eliminated timeout from LUN reset logic.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Made a couple of error messages more verbose.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed the workaround for the transition to spanning.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
small change to make code look cleaner
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Take advantage of controller improvements.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Port is deferenced before it is null sanity checked, hence we
potentially have a null pointer dereference bug. Instead, initialise
trl_enabled from port->fcs->bfa after we are sure port is not null.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 1 warning when build kernel with W=1:
drivers/scsi/qla4xxx/ql4_nx.c:1846:10: warning: no previous prototype for 'ql4_84xx_ipmdio_rd_reg' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static. This patch marks
this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 2 warnings about global functions without a declaration in the
scsi driver when building with W=1:
drivers/scsi/scsi_lib.c:467:6: warning: no previous prototype for 'scsi_requeue_run_queue' [-Wmissing-prototypes]
drivers/scsi/scsi_lib.c:2609:6: warning: no previous prototype for 'scsi_evt_thread' [-Wmissing-prototypes]
In fact, both functions are declared in drivers/scsi/scsi_scan.c but
need to move them into scsi_priv.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistakes in ql_dbg messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With commit 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
some versions of gcc now warn:
In file included from drivers/scsi/mac_scsi.c:335:
drivers/scsi/NCR5380.h:295: warning: `NCR5380_poll_politely' declared inline after being called
drivers/scsi/NCR5380.h:295: warning: previous declaration of `NCR5380_poll_politely' was here
Avoid this by defining NCR5380_poll_politely() in NCR5380.h.
[mkp: checkpatch warnings]
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Julia pointed out beiscsi_boot_get_sinfo does not unlock mbox_lock on
nonemb_cmd memory allocation failure.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
alloc_wrb_handle already does memset zero of iscsi_wrb descriptor so
remove redundant memset in WRB submission paths.
Add pwrb_handle NULL check before memsett'ing pwrb.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We know that 'ret' is not an error code because it has been tested a few
lines above. So, if one of these function fails, 0 will be returned
instead of an error code. Return -ENOMEM instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
'ret' needs to be set with error code if hba_setup_cid_tbls fails.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(unsigned long)' which is likely to
be 4.
It is likely that the number of bits in a long was expected here, so use
BITS_PER_LONG instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The MULDIV macro is essentially a duplicate of the more standard
mult_frac macro. Replace use of MULDIV with mult_frac & drop the
duplication.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calculating the maximum timeout that a user can set via the
SG_SET_TIMEOUT ioctl involves multiplying INT_MAX by USER_HZ/HZ. If
USER_HZ is larger than HZ then this results in an overflow when
performed as a 32 bit integer calculation, resulting in compiler
warnings such as the following:
drivers/scsi/sg.c: In function 'sg_ioctl':
drivers/scsi/sg.c:91:67: warning: integer overflow in expression [-Woverflow]
#define MULDIV(X,MUL,DIV) ((((X % DIV) * MUL) / DIV) + ((X / DIV) * MUL))
^
drivers/scsi/sg.c:887:14: note: in expansion of macro 'MULDIV'
if (val >= MULDIV (INT_MAX, USER_HZ, HZ))
^
drivers/scsi/sg.c:91:67: warning: integer overflow in expression [-Woverflow]
#define MULDIV(X,MUL,DIV) ((((X % DIV) * MUL) / DIV) + ((X / DIV) * MUL))
^
drivers/scsi/sg.c:888:13: note: in expansion of macro 'MULDIV'
val = MULDIV (INT_MAX, USER_HZ, HZ);
^
Avoid this overflow by performing the (constant) arithmetic on 64 bit
integers, which ensures that overflow from multiplying the 32 bit values
cannot occur. When converting the result back to a 32 bit integer use
min_t to ensure that we don't simply truncate a value beyond INT_MAX to
a 32 bit integer, but instead use INT_MAX where the result was larger
than it. As the values are all compile time constant the 64 bit
arithmetic should have no runtime cost.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ibmvfc driver currently doesn't support FC Class 3 Error Recovery.
However, it is simply a matter of informing the VIOS that the payload
expects to use sequence level error recovery via a bit flag in the
ibmvfc_cmd structure.
This patch adds a module parameter to enable error recovery support at
boot time. When enabled the RETRY service parameter bit is set during
PRLI, and ibmvfc_cmd->flags includes the IBMVFC_CLASS_3_ERR bit.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The READ FCP_XFER_READY DISABLED bit is required to always be set to one
since FCP-3. Set it in the service parameter page frame during process
login.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is likely that checking the result of 'pci_write_config_dword' is
expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Runtime PM should be configured already once we call device_add. See
also the description in this mail thread
https://lists.linuxfoundation.org/pipermail/linux-pm/2009-November/023198.html
or the order of calls e.g. in usb_new_device.
The changed order also helps to avoid scenarios where runtime pm for
&shost->shost_gendev is activated whilst the parent is suspended,
resulting in error message "runtime PM trying to activate child device
hostx but parent yyy is not active".
In addition properly reverse the runtime pm calls in the error path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch implements functions for pushing HCAM (host controlled
asynchronous messages) error buffers to userspace through sysfs
attributes. Reads to the "async_err_log" attribute will result in a
single HCAM buffer being copied to userspace; one can process the next
HCAM buffer by writing any string to the same attribute.
A new list was added to the ioa_cfg structure to store the HCAM buffers
for later reporting. We also send a KOBJ_CHANGE event whenever a new
HCAM buffer is made available to userspace.
Signed-off-by: Heitor Ricardo Alves de Siqueira <halves@linux.vnet.ibm.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a tmf is issued, various response codes can be returned from the
target. For a query tmf the response may be TMF_RESP_FUNC_COMPLETE or
TMF_RESP_FUNC_SUCC. Add a condition for TMF_RESP_FUNC_SUCC to
hisi_sas_exec_internal_tmf_task(). This affects query tmf, as the
result is success the returned value was for failure.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the port is detached we cannot execute a TMF, as there can be no
device attached to the port.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add code in slot_complete_v2_hw() to deal with the slots which have
completed due to internal abort.
The status codes have the following meaning:
- STAT_IO_ABORTED: the IO has been aborted due to internal abort,
whether by device or individual abort command
- STAT_IO_COMPLETE: internal abort command has completed successfully
for device or individual abort command
- STAT_IO_NO_DEVICE: internal abort command has completed for device but
cannot find any IO
- STAT_IO_NOT_VALID: internal abort command has completed for single
command but could not find the command
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add function to prepare the an internal abort for v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Execute an internal abort for executing a task abort.
This is for case of the command still being present
in host when abort is executed.
For a SATA internal abort, we set abort for all tasks
associated with the device.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Execute an internal abort for that device when it is removed, so that
commands for that device are not processed.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add main code for internal abort functionality.
The internal abort features allows the host controller to abort commands
which are still active in the controller but have not yet been sent to
the slave device.
Typically a command only spends a relatively short time in the
controller when compared to the amount of the time after it is sent to
the slave device.
Two modes of internal abort are supported:
- device
- individual command
For device, when the internal abort is issued all commands in the host
for that device are aborted. For a single command, only that command is
aborted if it is still in the host.
In HW the internal abort command is executed similar to any other sort
of command, like SSP.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
req_table is allocate by kzalloc, so we don't need to zero it again.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We don't need to use kzalloc as we will always memset the
local_atto_ioctl later.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current EQ delay is set to 0 to receive very high max interrupt per sec.
Set EQ delay to 32 - reducing max interrupt rate from 65K to 20K per sec.
Set TCP connection window size to 64K with scale shift count 2.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In very rare scenario, connection gets killed after throwing this error:
scsi host0: BM_2312 : Event CXN_KILLED_BAD_WRB_INDEX_ERROR[15]... CID : 4
connection1:0: detected conn error (1011)
memset ISCSI_WRB descriptor to zero for all allocations of WRB handle.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG: unable to handle kernel NULL pointer dereference at 000000000000015e
IP: [<ffffffffa0081700>]
hwi_get_async_handle.isra.23.constprop.39+0x90/0x1d0 [be2iscsi]
PGD 0
Oops: 0000 [#1] SMP
...
Call Trace:
<IRQ>
[<ffffffffa00818bc>] hwi_process_default_pdu_ring+0x7c/0x280 [be2iscsi]
[<ffffffffa0088f51>] beiscsi_process_cq+0x321/0xb90 [be2iscsi]
[<ffffffff810af028>] ? __wake_up_common+0x58/0x90
[<ffffffff810b0d84>] ? __wake_up+0x44/0x50
[<ffffffffa0089a2d>] be_iopoll+0x1d/0xb0 [be2iscsi]
[<ffffffff812d1f61>] blk_iopoll_softirq+0xc1/0x100
[<ffffffff81084b0f>] __do_softirq+0xef/0x280
The symptom observed is multiple async handles get queued for same index
thus causing leak in buffers posted to FW.
The root cause is:
- async handle is continued to be used even if it does not match the
completion.
- list_move operation done on already filled index.
1. Remove use of writables, host_write_ptr and ep_read_ptr.
2. Remove consumed logic to update writables. Instead, use only
free_entries to do the accounting of handles to be posted back.
3. Remove busy_list, instead use simple slot to index handles.
4. Added check no data, header less and overflow to make sure
all async_handles are flushed in error cases.
5. Added code to verify gathering of handles to form PDU by
checking final bit before forwarding PDU.
6. Added code to catch mismatch with CQE and handle gracefully.
7. Use AMAP, traverse cri_wait_queue list to post buffers, log
"async PDU" related errors.
8. Rearranged few data structures and added comments in init &
processing path.
9. Added WARN_ONs to catch any HD ring corruption.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver unload should call COMMON_FUNCTION_RESET. For TPE feature, this
ensures that FW has knowledge about driver getting unloaded and can
reset its bit vector.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sessions are no longer valid, so schedule sess_work to fail the sessions
immediately when error is detected. This is done to avoid iSCSI transport
layer to keep sending NOP-Out which driver any ways fail.
Schedule sess_work immediately in case of HBA error. Old sessions are gone
for good and need to be re-established.
iscsi_session_failure needs process context hence this work.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After UE is detected, check for recoverable error by reading
SLIPORT SEMAPHORE register. If transient parity error i.e. 0xExxx
then schedule recovery work on driver wq.
FLag this error to prevent any transactions for the duration of ue2rp to
restart polling. After that, if FW becomes ready then recover port.
Wake up processes in wq before going offline.
Wait for process to execute before cleaning up.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mgmt_epfw_cleanup does not implement v1 of OPCODE_COMMON_ISCSI_CLEANUP
IOCTL for SkyHawk.
Replace use of MCCQ with BMBX for issuing the IOCTL.
Remove be_mcc_compl_poll which is no longer needed.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLIPORT FUNCTION_RESET does not reset the chip.
So POST status needs to be checked before issuing FUNCTION_RESET.
The completion of FUNCTION_RESET is indicated in BMBX Rdy bit.
be_cmd_fw_initialize too needs to be done before issuing any cmd to FW.
be_cmd_fw_initialize is renamed as beiscsi_cmd_special_wrb.
Rearrange and rename few functions in init and cleanup path.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
beiscsi_fail_session is defined in be_cmds.c: move it to be_iscsi.c
Move card configuration commands to be_cmds.c.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BE3 and SH cards can recover from transient parity errors treated
earlier as unrecoverable errors.
Add IOCTL to query FW support for this feature.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UE detection in health check is done in a work scheduled in global wq.
UE caused due to transient parity errors are recoverable and reported
within 1s. If this check for TPE gets delayed, PF0 might initiate
soft-reset and then status of UE recoverable is lost.
Handle UE detection in timer routine. Move out EQ delay update work
from health check. Make the IOCTL for EQ delay update non-blocking
as the completion status is ignored.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Boot work involves:
1. Find and fetch configured boot session and its handle.
2. Attempt to open the session if its not.
3. Get the session details for boot kset creation.
4. Logout of that session owned by FW.
5. Create boot kset for session details.
All these actions were done in blocking call with retries in global wq.
Other works in wq suffered if the IOCTLs stalled or timed out.
This change moves all the boot work to make it non-blocking.
The work queued in global wq just issues the IOCTL depending on the action
to be taken and mcc wq schedules work depending on status of the IOCTL.
Initial boot_work is started on link and ASYNC event.
The other code changes move all boot related functions in one place and
follow naming conventions.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Save ue_detected and fw_timeout errors in state field of beiscsi_hba.
BEISCSI_HBA_RUNNING
BEISCSI_HBA_LINK_UP
BEISCSI_HBA_BOOT_FOUND
BEISCSI_HBA_PCI_ERR
BEISCSI_HBA_FW_TIMEOUT
BEISCSI_HBA_IN_UE
Make sure no PCI transaction happens once in error state.
Add checks in IO path to detect HBA in error.
Skip hwi_purge_eq step which can't be done in error state.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
todo_mcc_cq is not needed as only MCC work is queued.
todo_cq is not used at all.
Rename functions to be consistent.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
alloc_mcc_tag was replaced with alloc_mcc_wrb and is no more used.
beiscsi_pci_soft_reset is not used at all and won't be needed.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Redefine FW IP types.
Before issuing IOCTL to clear IP, check if IP is all zeroes.
All zeroes IP implies IP is not set in FW so FW fails that IOCTL.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
