VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two possible utilizations so far:
- Switch devices that don't support a native insertion/extraction header
on the CPU port may still enjoy the benefits of port isolation with a
custom VLAN tag.
For this, they need to have a customizable TPID in hardware and a new
Ethertype to distinguish between real 802.1Q traffic and the private
tags used for port separation.
- Switches that don't support the deactivation of VLAN awareness, but
still want to have a mode in which they accept all traffic, including
frames that are tagged with a VLAN not configured on their ports, may
use this as a fake to trick the hardware into thinking that the TPID
for VLAN is something other than 0x8100.
What follows after the ETH_P_DSA_8021Q EtherType is a regular VLAN
header (TCI), however there is no other EtherType that can be used for
this purpose and doesn't already have a well-defined meaning.
ETH_P_8021AD, ETH_P_QINQ1, ETH_P_QINQ2 and ETH_P_QINQ3 expect that
another follow-up VLAN tag is present, which is not the case here.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:
* "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
should not add an RX delay in this case)
The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
or less clear (needs to be added by the PHY), what should the MAC
driver do about the Tx delays? Is it an implicit wild card for the
MAC to apply delays in the Tx direction if it can? What if those were
already added as serpentine PCB traces, how could that be made more
obvious through DT bindings so that the MAC doesn't attempt to add
them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
fixed (a purely software entity that obviously cannot add clock
skew), what is the meaning of the above property?
So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.
The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.
For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.
Meanwhile do not allow the user to select an invalid configuration.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.
On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides an unified API for accessing register bit fields
regardless of memory layout. The basic unit of data for these API
functions is the u64. The process of transforming an u64 from native CPU
encoding into the peripheral's encoding is called 'pack', and
transforming it from peripheral to native CPU encoding is 'unpack'.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.
Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.
This simplifies driver probe path and particularly phy handling.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While moving the chunk of code during 739de9a156
("net: macb: Reorganize macb_mii bringup"), the declaration of
struct phy_device declaration was kept. It's not useful in this
function as we alrady have a phydev pointer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new compatible for WCN3998 and corresponding voltage
and current values to WCN3998 compatible.
Changed driver code to support WCN3998
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking fixes from David Miller:
1) Out of bounds access in xfrm IPSEC policy unlink, from Yue Haibing.
2) Missing length check for esp4 UDP encap, from Sabrina Dubroca.
3) Fix byte order of RX STBC access in mac80211, from Johannes Berg.
4) Inifnite loop in bpftool map create, from Alban Crequy.
5) Register mark fix in ebpf verifier after pkt/null checks, from Paul
Chaignon.
6) Properly use rcu_dereference_sk_user_data in L2TP code, from Eric
Dumazet.
7) Buffer overrun in marvell phy driver, from Andrew Lunn.
8) Several crash and statistics handling fixes to bnxt_en driver, from
Michael Chan and Vasundhara Volam.
9) Several fixes to the TLS layer from Jakub Kicinski (copying negative
amounts of data in reencrypt, reencrypt frag copying, blind nskb->sk
NULL deref, etc).
10) Several UDP GRO fixes, from Paolo Abeni and Eric Dumazet.
11) PID/UID checks on ipv6 flow labels are inverted, from Willem de
Bruijn.
12) Use after free in l2tp, from Eric Dumazet.
13) IPV6 route destroy races, also from Eric Dumazet.
14) SCTP state machine can erroneously run recursively, fix from Xin
Long.
15) Adjust AF_PACKET msg_name length checks, add padding bytes if
necessary. From Willem de Bruijn.
16) Preserve skb_iif, so that forwarded packets have consistent values
even if fragmentation is involved. From Shmulik Ladkani.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
udp: fix GRO packet of death
ipv6: A few fixes on dereferencing rt->from
rds: ib: force endiannes annotation
selftests: fib_rule_tests: print the result and return 1 if any tests failed
ipv4: ip_do_fragment: Preserve skb_iif during fragmentation
net/tls: avoid NULL pointer deref on nskb->sk in fallback
selftests: fib_rule_tests: Fix icmp proto with ipv6
packet: validate msg_namelen in send directly
packet: in recvmsg msg_name return at least sizeof sockaddr_ll
sctp: avoid running the sctp state machine recursively
stmmac: pci: Fix typo in IOT2000 comment
Documentation: fix netdev-FAQ.rst markup warning
ipv6: fix races in ip6_dst_destroy()
l2ip: fix possible use-after-free
appletalk: Set error code if register_snap_client failed
net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc
rxrpc: Fix net namespace cleanup
ipv6/flowlabel: wait rcu grace period before put_pid()
vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach
tcp: add sanity tests in tcp_add_backlog()
...
-----BEGIN PGP SIGNATURE-----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=KjZ4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190502' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"This is mostly io_uring fixes/tweaks. Most of these were actually done
in time for the last -rc, but I wanted to ensure that everything
tested out great before including them. The code delta looks larger
than it really is, as it's mostly just comment additions/changes.
Outside of the comment additions/changes, this is mostly removal of
unnecessary barriers. In all, this pull request contains:
- Tweak to how we handle errors at submission time. We now post a
completion event if the error occurs on behalf of an sqe, instead
of returning it through the system call. If the error happens
outside of a specific sqe, we return the error through the system
call. This makes it nicer to use and makes the "normal" use case
behave the same as the offload cases. (me)
- Fix for a missing req reference drop from async context (me)
- If an sqe is submitted with RWF_NOWAIT, don't punt it to async
context. Return -EAGAIN directly, instead of using it as a hint to
do async punt. (Stefan)
- Fix notes on barriers (Stefan)
- Remove unnecessary barriers (Stefan)
- Fix potential double free of memory in setup error (Mark)
- Further improve sq poll CPU validation (Mark)
- Fix page allocation warning and leak on buffer registration error
(Mark)
- Fix iov_iter_type() for new no-ref flag (Ming)
- Fix a case where dio doesn't honor bio no-page-ref (Ming)"
* tag 'for-linus-20190502' of git://git.kernel.dk/linux-block:
io_uring: avoid page allocation warnings
iov_iter: fix iov_iter_type
block: fix handling for BIO_NO_PAGE_REF
io_uring: drop req submit reference always in async punt
io_uring: free allocated io_memory once
io_uring: fix SQPOLL cpu validation
io_uring: have submission side sqe errors post a cqe
io_uring: remove unnecessary barrier after unsetting IORING_SQ_NEED_WAKEUP
io_uring: remove unnecessary barrier after incrementing dropped counter
io_uring: remove unnecessary barrier before reading SQ tail
io_uring: remove unnecessary barrier after updating SQ head
io_uring: remove unnecessary barrier before reading cq head
io_uring: remove unnecessary barrier before wq_has_sleeper
io_uring: fix notes on barriers
io_uring: fix handling SQEs requesting NOWAIT
Clang warns about the definitions of these macros (full warnings trimmed
for brevity):
drivers/net/wireless/realtek/rtw88/main.c:524:15: warning: signed shift
result (0x3FF00000000) requires 43 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
ra_mask &= RA_MASK_VHT_RATES | RA_MASK_OFDM_IN_VHT;
^~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:527:15: warning: signed shift
result (0xFF0000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
ra_mask &= RA_MASK_HT_RATES | RA_MASK_OFDM_IN_HT_5G;
^~~~~~~~~~~~~~~~
Given that these are all used with ra_mask, which is of type u64, we can
just declare the macros to be ULL as well.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/467
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-----BEGIN PGP SIGNATURE-----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=ajSb
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"I apologize for sending these so late in the cycle. We went back and
forth about how to deal with the unexpected logging of intentional
link state changes and finally decided to just config them off by
default.
PCI fixes:
- Stop ignoring "pci=disable_acs_redir" parameter (Logan Gunthorpe)
- Use shared MSI/MSI-X vector for Link Bandwidth Management (Alex
Williamson)
- Add Kconfig option for Link Bandwidth notification messages (Keith
Busch)"
* tag 'pci-v5.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/LINK: Add Kconfig option (default off)
PCI/portdrv: Use shared MSI/MSI-X vector for Bandwidth Management
PCI: Fix issue with "pci=disable_acs_redir" parameter being ignored
- Regression fix for the marvell nand driver.
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAlzGIXcWHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wccEEACKboXDWT+qMkUbSEfsmAG0lGlz
gDxZ5/EH4Lfi7KzCWKyLLwM0xXH3ZLQ6vCg3jm2odbEiqKOWbIS/6kjoLdrYhngv
+7LYAYmByozowiERjZn80EOrGp88oddf5H9+iRINh6U9g3ACR9xM9PMejKtxqust
dHrTtSsZvyO6+lrjPqgmIwhZeqQ/4Lp1fzoNjVPi+mT39gfR8RlJw3PUnPvknjff
Uxi/XrJUZEDex4MzvUwSNtBhUm1Mz3AHa9/gUHmUdPhbXLyQ2Qcsy2RJlwUPfn1T
CUR33j5rTOu+ThC8Aydz2FxyZng0IU3BO3TQnEEz87dNCCYNAtIFDdr+Wm1uV/jI
l8+w0vbfS8GazUU/EcaKVFSvK+b/5BvppClol4m1miI0I1wF5NIpYaSyG/OqVy3y
vEcNzQTGokU5gJX8r7VgeIsvoXevL1AlngFhD+Rks+Q7kJ1F+vDzWaxZHO1RJ/tC
Livk6DswWDAKx492rsTlF0My/WMrsleVS/9qJXkXDEEucVOD0Iox3biatjx5juKY
DCzTwfr6Jd6144d4wL/4w4rI7atGAWciv5WBkGf9Xh7pnhOsIfQ6z3kF1JB1vlJL
uHgRq0Vg20p3DzdpUXuz8dliNY7RIjciDuhq8a3RYyP7VzZZbZJRF82qEZhsbXTQ
Y60r0yUqyOrR/mnhDg==
=4gBj
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fix from Richard Weinberger:
"A single regression fix for the marvell nand driver"
* tag 'mtd/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: marvell: Clean the controller state before each operation
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/wireless/realtek/rtw88/phy.c: In function ‘rtw_get_channel_group’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:907:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:908:2: note: here
case 1:
^~~~
In file included from ./include/linux/bcd.h:5,
from drivers/net/wireless/realtek/rtw88/phy.c:5:
drivers/net/wireless/realtek/rtw88/phy.c: In function ‘phy_get_2g_tx_power_index’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:1021:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:1022:2: note: here
case RTW_CHANNEL_WIDTH_20:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the shift of an integer value more than 32 bits can
occur when nss is more than 32. Fix this by making the integer
constants unsigned long longs before shifting and bit-wise or'ing
with the u64 ra_mask to avoid the undefined shift behaviour.
Addresses-Coverity: ("Bad shift operation")
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth
notification") added dmesg logging whenever a link changes speed or width
to a state that is considered degraded. Unfortunately, it cannot
differentiate signal integrity-related link changes from those
intentionally initiated by an endpoint driver, including drivers that may
live in userspace or VMs when making use of vfio-pci. Some GPU drivers
actively manage the link state to save power, which generates a stream of
messages like this:
vfio-pci 0000:07:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:02.0 (capable of 64.000 Gb/s with 5 GT/s x16 link)
Since we can't distinguish the intentional changes from the signal
integrity issues, leave the reporting turned off by default. Add a Kconfig
option to turn it on if desired.
Fixes: e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/linux-pci/20190501142942.26972-1-keith.busch@intel.com
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fixes: d84aec4215 ("net: ll_temac: Fix support for 64-bit platforms")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err makes more sense than dev_info when this call fails.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the link event flow works, but can be much better.
Refactor the link event flow to make it cleaner and more clear
on what is going on.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY type ICE_PHY_TYPE_LOW_25G_AUI_C2C is missing from
ice_get_settings_link_up() which is causing a warning
message for unrecognized PHY. Add the PHY type to
correctly set the settings and avoid the warning message.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Every time we want to re-enable interrupts and/or write to a register
that requires an interrupt vector's hardware index we do the following:
vsi->hw_base_vector + q_vector->v_idx
This is a wasteful operation, especially in the hot path. Fix this by
adding a u16 reg_idx member to the ice_q_vector structure and make the
necessary changes to make this work.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Runtime change of PFINT_OICR_ENA register is unnecessary.
The handlers should always clear the atomic bit for each
task as they start, because it will make sure that any late
interrupt will either 1) re-set the bit, or 2) be handled
directly in the "already running" task handler.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issue with non trusted VFs being able to add more than
permitted number of VLANs by adding a check in ice_vc_process_vlan_msg.
Also don't return an error in this case as the VF does not need to know
that it is not trusted.
Also rework ice_vsi_kill_vlan to use the right types.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_vsi_ctrl_rx_rings() we are unnecessarily waiting for
QRX_CTRL_QENA_REQ and QRX_CTRL_QENA_STAT to be the same value prior to
disabling each Rx queue. There is no reason to do this so remove
this wait loop as we already have a wait loop after disabling/enabling
the Rx queue through the QRX_CTRL register to make sure it gets
successfully disabled/enabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver allows rx-usecs-high values to be set,
but when querying the device for rx-usecs-high the value
does not stick. This is because it was not yet implemented.
Add code to allow the user to change rx-usecs-high and
use this to set the q_vector's intrl value.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support to set 52 byte RSS hash key.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many places in the code where we do the following:
for (i = 0; i < vsi->num_q_vectors; i++)
Instead use the macro mentioned in the commit title:
ice_for_each_q_vector(vsi, i)
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When stopping Tx rings, we use 'i' as an ring array index for looking up
whether the ice_ring exists and have assigned a q_vector. This checks
rings only within a given TC and we need to go through every ring in
VSI. Use 'q_idx' instead.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce scope of the variable 'err' to inside the for loop instead
of using it as a second looping conditional. Also while here,
improve the debug message if we fail to configure a Rx queue.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis points out the default case in the switch statement in
ice_get_itr_intrl_gran() is an infeasible condition causing the default
case statement to be unreachable. Remove it and since the function no
longer returns anything but success, change it to just return void and
update the only call to it accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If there is no queue to disable, return appropriate configuration error
earlier without acquiring the lock.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a framework to store queue specific information
in VSI queue contexts. Currently VSI queue context (represented by
struct ice_q_ctx) only has q_handle as a member. In future patches,
this structure will be updated to hold queue specific information.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
syzbot was able to crash host by sending UDP packets with a 0 payload.
TCP does not have this issue since we do not aggregate packets without
payload.
Since dev_gro_receive() sets gso_size based on skb_gro_len(skb)
it seems not worth trying to cope with padded packets.
BUG: KASAN: slab-out-of-bounds in skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
Read of size 16 at addr ffff88808893fff0 by task syz-executor612/7889
CPU: 0 PID: 7889 Comm: syz-executor612 Not tainted 5.1.0-rc7+ #96
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load16_noabort+0x14/0x20 mm/kasan/generic_report.c:133
skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
udp_gro_receive_segment net/ipv4/udp_offload.c:382 [inline]
call_gro_receive include/linux/netdevice.h:2349 [inline]
udp_gro_receive+0xb61/0xfd0 net/ipv4/udp_offload.c:414
udp4_gro_receive+0x763/0xeb0 net/ipv4/udp_offload.c:478
inet_gro_receive+0xe72/0x1110 net/ipv4/af_inet.c:1510
dev_gro_receive+0x1cd0/0x23c0 net/core/dev.c:5581
napi_gro_frags+0x36b/0xd10 net/core/dev.c:5843
tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
call_write_iter include/linux/fs.h:1866 [inline]
do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
do_iter_write fs/read_write.c:957 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:938
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
do_writev+0x15e/0x370 fs/read_write.c:1037
__do_sys_writev fs/read_write.c:1110 [inline]
__se_sys_writev fs/read_write.c:1107 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441cc0
Code: 05 48 3d 01 f0 ff ff 0f 83 9d 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 3d 51 93 29 00 00 75 14 b8 14 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 74 09 fc ff c3 48 83 ec 08 e8 ba 2b 00 00
RSP: 002b:00007ffe8c716118 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00007ffe8c716150 RCX: 0000000000441cc0
RDX: 0000000000000001 RSI: 00007ffe8c716170 RDI: 00000000000000f0
RBP: 0000000000000000 R08: 000000000000ffff R09: 0000000000a64668
R10: 0000000020000040 R11: 0000000000000246 R12: 000000000000c2d9
R13: 0000000000402b50 R14: 0000000000000000 R15: 0000000000000000
Allocated by task 5143:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_kmalloc mm/kasan/common.c:497 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470
kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505
slab_post_alloc_hook mm/slab.h:437 [inline]
slab_alloc mm/slab.c:3393 [inline]
kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555
mm_alloc+0x1d/0xd0 kernel/fork.c:1030
bprm_mm_init fs/exec.c:363 [inline]
__do_execve_file.isra.0+0xaa3/0x23f0 fs/exec.c:1791
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 5351:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:459
kasan_slab_free+0xe/0x10 mm/kasan/common.c:467
__cache_free mm/slab.c:3499 [inline]
kmem_cache_free+0x86/0x260 mm/slab.c:3765
__mmdrop+0x238/0x320 kernel/fork.c:677
mmdrop include/linux/sched/mm.h:49 [inline]
finish_task_switch+0x47b/0x780 kernel/sched/core.c:2746
context_switch kernel/sched/core.c:2880 [inline]
__schedule+0x81b/0x1cc0 kernel/sched/core.c:3518
preempt_schedule_irq+0xb5/0x140 kernel/sched/core.c:3745
retint_kernel+0x1b/0x2d
arch_local_irq_restore arch/x86/include/asm/paravirt.h:767 [inline]
kmem_cache_free+0xab/0x260 mm/slab.c:3766
anon_vma_chain_free mm/rmap.c:134 [inline]
unlink_anon_vmas+0x2ba/0x870 mm/rmap.c:401
free_pgtables+0x1af/0x2f0 mm/memory.c:394
exit_mmap+0x2d1/0x530 mm/mmap.c:3144
__mmput kernel/fork.c:1046 [inline]
mmput+0x15f/0x4c0 kernel/fork.c:1067
exec_mmap fs/exec.c:1046 [inline]
flush_old_exec+0x8d9/0x1c20 fs/exec.c:1279
load_elf_binary+0x9bc/0x53f0 fs/binfmt_elf.c:864
search_binary_handler fs/exec.c:1656 [inline]
search_binary_handler+0x17f/0x570 fs/exec.c:1634
exec_binprm fs/exec.c:1698 [inline]
__do_execve_file.isra.0+0x1394/0x23f0 fs/exec.c:1818
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff88808893f7c0
which belongs to the cache mm_struct of size 1496
The buggy address is located 600 bytes to the right of
1496-byte region [ffff88808893f7c0, ffff88808893fd98)
The buggy address belongs to the page:
page:ffffea0002224f80 count:1 mapcount:0 mapping:ffff88821bc40ac0 index:0xffff88808893f7c0 compound_mapcount: 0
flags: 0x1fffc0000010200(slab|head)
raw: 01fffc0000010200 ffffea00025b4f08 ffffea00027b9d08 ffff88821bc40ac0
raw: ffff88808893f7c0 ffff88808893e440 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808893fe80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88808893ff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88808893ff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888088940000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888088940080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fixes: e20cf8d3f1 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* cpcap-battery: fix a division by zero
* core: fix systemd issue due to log messages produced by uevent
-----BEGIN PGP SIGNATURE-----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=Q783
-----END PGP SIGNATURE-----
Merge tag 'for-v5.1-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"Two more fixes for the 5.1 cycle.
One division by zero fix in a specific driver and one core workaround
for bad userspace behaviour from systemd regarding uevents. IMHO this
can be considered to be a userspace bug, but the debug messages are
useless anyways
- cpcap-battery: fix a division by zero
- core: fix systemd issue due to log messages produced by uevent"
* tag 'for-v5.1-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: sysfs: prevent endless uevent loop with CONFIG_POWER_SUPPLY_DEBUG
power: supply: cpcap-battery: Fix division by zero
When the state of rep was introduced, it was also designed to prevent
duplicate unloading of the same rep. Considering the following two
flows when an eswitch manager is at switchdev mode with n VF reps loaded.
+--------------------------------------+--------------------------------+
| cpu-0 | cpu-1 |
| -------- | -------- |
| mlx5_ib_remove | mlx5_eswitch_disable_sriov |
| mlx5_ib_unregister_vport_reps | esw_offloads_cleanup |
| mlx5_eswitch_unregister_vport_reps | esw_offloads_unload_all_reps |
| __unload_reps_all_vport | __unload_reps_all_vport |
+--------------------------------------+--------------------------------+
These two flows will try to unload the same rep. Per original design,
once one flow unloads the rep, the state moves to REGISTERED. The 2nd
flow will no longer needs to do the unload and bails out. However, as
read and write of the state is not atomic, when 1st flow is doing the
unload, the state is still LOADED, 2nd flow is able to do the same
unload action. Kernel crash will happen.
To solve this, driver should do atomic test-and-set for the state. So
that only one flow can change the rep state from LOADED to REGISTERED,
and proceed to do the actual unloading.
Since the state is changing to atomic type, all other read/write should
be atomic action as well.
Fixes: f121e0ea95 (net/mlx5: E-Switch, Add state to eswitch vport representors)
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The check of legal vport is to ensure the vport number falls between
0 and total number of vports. Along with the introduction of uplink
rep, enabled vports are not consecutive any more.
Therefore, rely on the eswitch vport getter function to check if it's
a valid vport.
As the getter function relies on eswitch, add the check of vport
group manager and validation the presence of eswitch structure.
Remove the redundant check in the function calls.
Since the vport array will be allocated once eswitch is initialized
and will be kept alive if eswitch presents, no need to protect it with
the state lock.
Fixes: 5ae5162066 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some functions issue vport commands and access vport array using
vport_index/vport_num interchangeably which is OK for VFs vports.
However, this creates potential bug if those vports are not VFs
(E.g, uplink, sf) where their vport_index don't equal to vport_num.
Prepare code to access mlx5_vport structure using a getter function.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Several functions need to access mlx5_vport and vport_num.
When these functions are called, caller already has mlx5_vport*
available.
Hence pass such mlx5_vport pointer.
This is preparation patch to add error checks to
mlx5_eswitch_get_vport() and to return error status.
By doing so, reduce places where error check of mlx5_eswitch_get_vport()
can be avoided.
While doing such change, mlx5_eswitch_query_vport_drop_stats() gets
corrected to work on vport, instead of vport_idx.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently mlx5_esw_for_each_vf_vport iterates over mlx5_vport entries in
eswitch.c
Same macro in eswitch_offloads.c iterates over vport number in
eswitch_offloads.c
Instead of duplicate macro names, to avoid confusion and to reuse the
same macro in both files, move it to eswitch.h.
To iterate over vport numbers where there is no need to iterate over
mlx5_vport, but only a vport number is needed, rename those macros in
eswitch_offloads.c to mlx5_esw_for_each_vf_num_vport*.
While at it, keep all vport and vport rep iterators together.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_query_nic_vport_vlans() is not used anymore. Hence remove it.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CFLAGS_tracepoint.o specifies CFLAGS for compiling tracepoint.c but
it does not exist under drivers/net/ethernet/mellanox/mlx5/core/.
CFLAGS_tracepoint.o is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The same code that returns XDP frames and releases pages is used both in
mlx5e_poll_xdpsq_cq and mlx5e_free_xdpsq_descs. Create a function that
cleans up an MPWQE.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the support to read additional EEPROM information from high pages.
Information for modules such as SFF-8436 and SFF-8636:
1) Application select table
2) User writable EEPROM
3) Thresholds and alarms
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added max EEPROM length defines for ethtool usage:
#define ETH_MODULE_SFF_8636_MAX_LEN 640
#define ETH_MODULE_SFF_8436_MAX_LEN 640
These definitions are used to determine the EEPROM
data length when reading high eeprom pages.
For example, SFF-8636 EEPROM data from page 03h
needs to be stored at data[512] - data[639].
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With unlocked TC it is possible to have spurious deletes and inserts of
same filter. TC layer needs drivers to always return error when flow
insertion failed in order to correctly calculate "in_hw_count" for each
filter. Fix mlx5e_configure_flower() to return -EEXIST when TC tries to
insert a filter that is already provisioned to the driver.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets are
tagged with VLAN ID 0x000 (priority tag) and pop/push actions are
replaced by VLAN re-write actions (which are supported by the HW).
Replace TC VLAN pop action with a VLAN priority tag header rewrite.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
