get_pipe() routine doesn't validate the input endpoint number
and uses to reference ep_in and ep_out arrays. Invalid endpoint
number can trigger BUG(). Range check the epnum and returning
error instead of calling BUG().
Change caller stub_recv_cmd_submit() to handle the get_pipe()
error return.
Reported-by: Secunia Research <vuln@secunia.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is another JMS567-based USB3 UAS enclosure (152d:0578) that fails
with the following error:
[sda] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[sda] tag#0 Sense Key : Illegal Request [current]
[sda] tag#0 Add. Sense: Invalid field in cdb
The issue occurs both with UAS (occasionally) and mass storage
(immediately after mounting a FS on a disk in the enclosure).
Enabling US_FL_BROKEN_FUA quirk solves this issue.
This patch adds an UNUSUAL_DEV with US_FL_BROKEN_FUA for the enclosure
for both UAS and mass storage.
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.
In this case, we should handle the babble interrupt first and recover
from the babble condition.
This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present, TCPM code assumes that local device supports
variable/batt pdos and always selects the pdo with highest
possible power within the board limit. This assumption
might not hold good for all devices. To overcome this,
this patch makes TCPM only accept a source_pdo when there is
a matching sink pdo.
For Fixed pdos: The voltage should match between the
incoming source_cap and the registered snk_pdo
For Variable/Batt pdos: The incoming source_cap voltage
range should fall within the registered snk_pdo's voltage
range.
Also, when the cap_mismatch bit is set, the max_power/current
should be set to the max_current/power of the sink_pdo.
This is according to:
"If the Capability Mismatch bit is set to one
The Maximum Operating Current/Power field may contain a value
larger than the maximum current/power offered in the Source
Capabilities message’s PDO as referenced by the Object position field.
This enables the Sink to indicate that it requires more current/power
than is being offered. If the Sink requires a different voltage this
will be indicated by its Sink Capabilities message.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The source and sink caps should follow the following rules.
This patch validates whether the src_caps/snk_caps adheres
to it.
6.4.1 Capabilities Message
A Capabilities message (Source Capabilities message or Sink
Capabilities message) shall have at least one Power
Data Object for vSafe5V. The Capabilities message shall also
contain the sending Port’s information followed by up to
6 additional Power Data Objects. Power Data Objects in a
Capabilities message shall be sent in the following order:
1. The vSafe5V Fixed Supply Object shall always be the first object.
2. The remaining Fixed Supply Objects, if present, shall be sent
in voltage order; lowest to highest.
3. The Battery Supply Objects, if present shall be sent in Minimum
Voltage order; lowest to highest.
4. The Variable Supply (non-battery) Objects, if present, shall be
sent in Minimum Voltage order; lowest to highest.
Errors in source/sink_caps of the local port will prevent
the port registration. Whereas, errors in source caps of partner
device would only log them.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This corrects the endpiont type value set to the DbC bulk in endpoint.
The previous value doesn't cause any problems because that we now only
use the bulk out endpoint. Set the hardware with the correct value any
way.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 7fee72d5e8 ("uas: Always apply US_FL_NO_ATA_1X quirk to
Seagate devices"), the US_FL_NO_ATA_1X is always set for Seagate devices,
so the per device unusual_uas.h entries for Seagate devices can be
removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replacing dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface drivers like btusb that don't support reset-resume will be
rebound at resume if port was reset. Rebind is done during the pm_ops
.complete callback when probe returns EPROBE_DEFER as default.
Remove the "rebind failed: -517" message.
Device probe will eventually take place later.
[one-liner by Jerry Snitselaar posted in a mailing list question -Mathias]
Suggested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fix of "FIXME: Notify the subdrivers..." doesn't actually have any
real effect. The "FIXME" changed to simple comment.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using a period after a newline causes bad output.
Miscellanea:
o Coalesce formats too
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC can generate two events for a short transfer if the short TRB and
last TRB in the TD are not the same TRB.
The driver will handle the TD after the first short event, and remove
it from its internal list. Driver then incorrectly prints a warning
for the second event:
"WARN Event TRB for slot x ep y with no TDs queued"
Fix this by not printing a warning if we get a event on a empty list
if the previous event was a short event.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe writes:
usb: fixes for v4.15-rc2
After a long time, we finally have a good solution for how to handle
OS descriptor on FFS. From now on we will force the Reserved field to
be 1 as mandated by the specification.
Apart from that, we have a couple other smaller fixes:
- FFS learned to not sleep in atomic context.
- UDC-core has a fix for the way we set a UDC's operating speed.
- Renesas USB3 has a fix for the maximum number of pipes supported
- Allow legacy drivers to be compiled without USB_ETH
- Fix some coccinelle warnings
Johan writes:
USB-serial fixes for v4.15-rc2
Here are some new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
We've been adding this as a quirk on a per device basis hoping that
newer disk enclosures would do better, but that has not happened,
so simply apply this quirk to all Seagate devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KY-688 USB 3.1 Type-C Hub internally uses a Genesys Logic hub to connect
to Realtek r8153.
Similar to commit ("7496cfe5431f2 usb: quirks: Add no-lpm quirk for Moshi
USB to Ethernet Adapter"), no-lpm can make r8153 ethernet work.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the USB device gets confused about the state of the initialization and
the connection fails. In particular, the device thinks that it's already set up
and running while the host thinks the device still needs to be configured. To
work around this issue, power-cycle the hub's output to issue a sort of "reset"
to the device. This makes the device restart its state machine and then the
initialization succeeds.
This fixes problems where the kernel reports a list of errors like this:
usb 1-1.3: device not accepting address 19, error -71
The end result is a non-functioning device. After this patch, the sequence
becomes like this:
usb 1-1.3: new high-speed USB device number 18 using ci_hdrc
usb 1-1.3: device not accepting address 18, error -71
usb 1-1.3: new high-speed USB device number 19 using ci_hdrc
usb 1-1.3: device not accepting address 19, error -71
usb 1-1-port3: attempt power cycle
usb 1-1.3: new high-speed USB device number 21 using ci_hdrc
usb-storage 1-1.3:1.2: USB Mass Storage device detected
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As most of BOS descriptors are longer in length than their header
'struct usb_dev_cap_header', comparing solely with it is not sufficient
to avoid out-of-bounds access to BOS descriptors.
This patch adds descriptor type specific length check in
usb_get_bos_descriptor() to fix the issue.
Signed-off-by: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable temp is incorrectly being updated, instead it should
be offset otherwise the loop just reads the same capability value
and loops forever. Thanks to Alan Stern for pointing out the
correct fix to my original fix. Fix also cleans up clang warning:
drivers/usb/host/ehci-dbg.c:840:4: warning: Value stored to 'temp'
is never read
Fixes: d49d431744 ("USB: misc ehci updates")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bus-node lookup during registration, which ended up searching the whole
device tree depth-first starting at the parent (or grand parent) rather
than just matching on its children.
To make things worse, the parent (or grand-parent) node could end being
prematurely freed as well.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: stable <stable@vger.kernel.org> # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is more clear from user perspective to wrap the whole USB
Type-C support under a single option that the user can
select, then it is to always ask the user for every USB
Type-C and USB Power Delivery driver separately.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the USB device-node helper that is used to look up a device
node given a parent hub device and a port number. Also pass in a struct
usb_device as first argument to provide some type checking.
Give the helper the more descriptive name usb_of_get_device_node(),
which matches the new usb_of_get_interface_node() helper that is used to
look up a second type of of child node from a USB device.
Note that the terms "device node" and "interface node" are defined and
used by the OF Recommended Practice for USB.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code looks up a USB device node from a given parent USB device but
never dropped its reference to the returned node.
As only the address of the node is used for a later matching, the
reference can be dropped immediately.
Note that this trigger implementation confuses the description of the
USB device connected to a port with the port itself (which does not have
a device-tree representation).
Fixes: 4f04c210d0 ("usb: core: read USB ports from DT in the usbport LED trigger driver")
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add OF device-tree support for USB interfaces.
USB "interface nodes" are children of USB "device nodes" and are
identified by an interface number and a configuration value:
&usb1 { /* host controller */
dev1: device@1 { /* device at port 1 */
compatible = "usb1234,5678";
reg = <1>;
#address-cells = <2>;
#size-cells = <0>;
interface@0,2 { /* interface 0 of configuration 2 */
compatible = "usbif1234,5678.config2.0";
reg = <0 2>;
};
};
};
The configuration component is not included in the textual
representation of an interface-node unit address for configuration 1:
&dev1 {
interface@0 { /* interface 0 of configuration 1 */
compatible = "usbif1234,5678.config1.0";
reg = <0 1>;
};
};
When a USB device of class 0 or 9 (hub) has only a single configuration
with a single interface, a special case "combined node" is used instead
of a device node with an interface node:
&usb1 {
device@2 {
compatible = "usb1234,abcd";
reg = <2>;
};
};
Combined nodes are shared by the two device structures representing the
USB device and its interface in the kernel's device model.
Note that, as for device nodes, the compatible strings for interface
nodes are currently not used.
For more details see "Open Firmware Recommended Practice: Universal
Serial Bus Version 1" and the binding documentation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expectation in the FUSB302 driver is that a TX_SUCCESS event
should occur after a message has been sent, but before a GCRCSENT
event is raised to indicate successful receipt of a message from
the partner. However in some circumstances it is possible to see
the hardware raise a GCRCSENT event before a TX_SUCCESS event
is raised. The upshot of this is that the GCRCSENT handling portion
of code ends up reporting the GoodCRC message to TCPM because the
TX_SUCCESS event hasn't yet arrived to trigger a consumption of it.
When TX_SUCCESS is then raised by the chip it ends up consuming the
actual message that was meant for TCPM, and this incorrect sequence
results in a hard reset from TCPM.
To avoid this problem, this commit updates the message reading
code to check whether a GoodCRC message was received or not. Based
on this check it will either report that the previous transmission
has completed or it will pass the msg data to TCPM for futher
processing. This way the incorrect ordering of the events no longer
matters.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable t is assigned but never read, it is redundant and therefore
can be removed. Cleans up clang warning:
drivers/usb/host/whci/asl.c:106:3: warning: Value stored to 't' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The specification says that the Reserved1 field in OS_DESC_EXT_COMPAT
must have the value "1", but when this feature was first implemented we
rejected any non-zero values.
This was adjusted to accept all non-zero values (while now rejecting
zero) in commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on
reserved1 of OS_DESC_EXT_COMPAT"), but that breaks any userspace
programs that worked previously by returning EINVAL when Reserved1 == 0
which was previously the only value that succeeded!
If we just set the field to "1" ourselves, both old and new userspace
programs continue to work correctly and, as a bonus, old programs are
now compliant with the specification without having to fix anything
themselves.
Fixes: 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 of OS_DESC_EXT_COMPAT")
Cc: <stable@vger.kernel.org>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently UDC core calls ->udc_set_speed() with the speed parameter
containing the maximum speed supported by the gadget function
driver. This might very well be more than that supported by the
UDC controller driver.
Select the lesser of the 2 speeds so both UDC and gadget function
driver are operating within limits.
This fixes PHY Erratic errors and 2 second enumeration delay on
TI's AM437x platforms.
Fixes: 6099eca796ae ("usb: gadget: core: introduce ->udc_set_speed() method")
Cc: <stable@vger.kernel.org> # v4.13+
Reported-by: Dylan Howey <Dylan.Howey@tennantco.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Considerable time ago the legacy gadget menu was added inside the
USB_ETH choice. I think this was a mistake and that the legacy
gadget menu should have been added after "endchoice" instead of
before. Hence this patch.
Fixes: commit 8443f2d2b7 ("usb: gadget: Gadget directory cleanup - group legacy gadgets")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This controller on R-Car Gen3 has 6 pipes that included PIPE 0 for
control actually. But, the datasheet has error in writing as it has
31 pipes. (However, the previous code defined 30 pipes wrongly...)
Anyway, this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoid dereferencing pointer g until after g has been sanity null checked;
move the assignment of cdev much later when it is required into a more
local scope.
Detected by CoverityScan, CID#1222135 ("Dereference before null check")
Fixes: b785ea7ce6 ("usb: gadget: composite: fix ep->maxburst initialization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
write_reg returns 0 on success, we can make it more explicit by returning
number 0 instead of result variable.
read_reg should return 0 on success since this is a more common pattern.
The user of read_reg has been clean-up and should be at the same commit.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The assignment of DIV to itself is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove .owner field if calls are used which set it automatically
drivers/usb/gadget/udc/bdc/bdc_core.c:645:3-8: No need to set .owner here. The core will do it.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel
development board (EVB). The USB id is added to option.c to allow
DIAG,GPS,AT and modem communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull sound updates from Takashi Iwai:
"There are no big surprising changes in this cycle, yet not too boring,
either. The biggest change from diffstat POV is the removal of the
legacy OSS driver codes that have been already disabled for a long
time. This will bring a few trivial merge conflicts.
As new features in ASoC side, there are two things: a new AC97 bus
implementation and AMD Stony platform support. Both include the
relevant changes shared with other subsystems, e.g. AC97 MFD changes
and DRM AMD changes.
Some other highlighted topics are:
- A bunch of USB-audio drivers got the hardening against the
malicious device accesses with a new helper code for endpoint
sanity check
- Lots of cleanups for ASoC Intel platform code, including support
for their open source audio firmware
- Continued ASoC core componentization works
- Support for scaling MCLK with sample rate in ASoC simple-card
- Stabler PCM hot-unplug capability, especially for ASoC usages"
* tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits)
Documentation: sound: hd-audio: notes.rst
ASoC: bcm2835: Support left/right justified and DSP modes
ASoC: bcm2835: Enforce full symmetry
ASoC: bcm2835: Support additional samplerates up to 384kHz
ASoC: bcm2835: Add support for TDM modes
ASoC: add mclk-fs support to audio graph card
ASoC: add mclk-fs to audio graph card binding
ASoC: rt5514: work around link error
ASoC: rt5514: mark PM functions as __maybe_unused
ASoC: rt5663: Check the JD status in the button pushing
ASoC: amd: Modified DMA transfer Mechanism for Playback
ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2
ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+
ASoC: da7213: add support for DSP modes
ASoC: sun8i-codec: Add a comment on the LRCK inversion
ASoC: sun8i-codec: Set the BCLK divider
ASoC: rt5663: Delay and retry reading rt5663 ID register
ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds
ASoC: cs42l56: Fix reset GPIO name in example DT binding
ASoC: rt5514-spi: check irq status to schedule data copy in resume function
...
