This feature is optional and is enabled if the BIOS requests any
Windows OSI strings. It can also be enabled by the host OS.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
To prevent accidental deep sleeps, limit the maximum time that
Sleep() will sleep. Configurable, default maximum is two seconds.
ACPICA bugzilla 854.
http://www.acpica.org/bugzilla/show_bug.cgi?id=854
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The sysfs interface allowing user space to disable/enable GPEs
doesn't work correctly, because a GPE disabled this way will be
re-enabled shortly by acpi_ev_asynch_enable_gpe() if it was
previosuly enabled by acpi_enable_gpe() (in which case the
corresponding bit in its enable register's enable_for_run mask is
set).
To address this issue make the sysfs GPE interface use
acpi_enable_gpe() and acpi_disable_gpe() instead of acpi_set_gpe()
so that GPE reference counters are modified by it along with the
values of GPE enable registers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
While developing the GPE reference counting code we overlooked the
fact that acpi_ev_update_gpes() could have enabled GPEs before
acpi_ev_initialize_gpe_block() was called. As a result, some GPEs
are enabled twice during the initialization.
To fix this issue avoid calling acpi_enable_gpe() from
acpi_ev_initialize_gpe_block() for the GPEs that have nonzero
runtime reference counters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_hw_write_gpe_enable_reg() to re-enable a GPE after
an event signaled by it has been handled. However, this function
writes the entire GPE enable mask to the GPE's enable register which
may not be correct. Namely, if one of the other GPEs in the same
register was previously enabled by acpi_enable_gpe() and subsequently
disabled using acpi_set_gpe(), acpi_hw_write_gpe_enable_reg() will
re-enable it along with the target GPE.
To fix this issue rework acpi_hw_write_gpe_enable_reg() so that it
calls acpi_hw_low_set_gpe() with a special action value,
ACPI_GPE_COND_ENABLE, that will make it only enable the GPE if the
corresponding bit in its register's enable_for_run mask is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe(). As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.
To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level. Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In quite a few places ACPICA needs to compute a GPE enable mask with
only one bit, corresponding to a given GPE, set. Currently, that
computation is always open coded which leads to unnecessary code
duplication. Fix this by introducing a helper function for computing
one-bit GPE enable masks and using it where appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 0f849d2cc6 (ACPICA: Minimize
the differences between linux GPE code and ACPICA code base)
introduced a change attempting to disable a GPE before installing
a handler for it in acpi_install_gpe_handler() which was incorrect.
First, the GPE disabled by it is never enabled again (except during
resume) which leads to battery insert/remove events not being
reported on the Maxim Levitsky's machine. Second, the disabled
GPE is still reported as enabled by the sysfs interface that only
checks its enable register's enable_for_run mask.
Revert this change for now, because it causes more damage to happen
than the bug it was supposed to fix.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_enter_[simple|bm] routines does us to pm tick conversion on every
idle wakeup and the value is only used in /proc/acpi display. We can
store the time in us and convert it into pm ticks before printing instead and
avoid the conversion in the common path.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The C-state idle time is not calculated correctly, which will return the wrong
residency time in C-state. It will have the following effects:
1. The system can't choose the deeper C-state when it is idle next time.
Of course the system power is increased. E.g. On one server machine about 40W
idle power is increased.
2. The powertop shows that it will stay in C0 running state about 95% time
although the system is idle at most time.
2.6.35-rc1 regression caused-by: 2da513f582
(ACPI: Minor cleanup eliminating redundant PMTIMER_TICKS to NS conversion)
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reported-by: Yu Zhidong <zhidong.yu@intel.com>
Tested-by: Yu Zhidong <zhidong.yu@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As suggested in Venki's suggestion in the commit 0dc698b,
add LAPIC unstable detection in the acpi_pad drvier too.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The names of the functions used for blocking/unblocking EC
transactions during suspend/hibernation suggest that the transactions
are suspended and resumed by them, while in fact they are disabled
and enabled. Rename the functions (and the flag used by them) to
better reflect what they really do.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
There still is a race that may result in suspending the system in
the middle of an EC transaction in progress, which leads to problems
(like the kernel thinking that the ACPI global lock is held during
resume while in fact it's not).
To remove the race condition, modify the ACPI platform suspend and
hibernate callbacks so that EC transactions are blocked right after
executing the _PTS global control method and are allowed to happen
again right after the low-level wakeup.
Introduce acpi_pm_freeze() that will disable GPEs, wait until the
event queues are empty and block EC transactions. Use it wherever
GPEs are disabled in preparation for switching local interrupts off.
Introduce acpi_pm_thaw() that will allow EC transactions to happen
again and enable runtime GPEs. Use it to balance acpi_pm_freeze()
wherever necessary.
In addition to that use acpi_ec_resume_transactions_early() to
unblock EC transactions as early as reasonably possible during
resume. Also unblock EC transactions in acpi_hibernation_finish()
and in the analogous suspend routine to make sure that the EC
transactions are enabled in all error paths.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=14668
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
intel_idle: native hardware cpuidle driver for latest Intel processors
ACPI: acpi_idle: touch TS_POLLING only in the non-MWAIT case
acpi_pad: uses MONITOR/MWAIT, so it doesn't need to clear TS_POLLING
sched: clarify commment for TS_POLLING
ACPI: allow a native cpuidle driver to displace ACPI
cpuidle: make cpuidle_curr_driver static
cpuidle: add cpuidle_unregister_driver() error check
cpuidle: fail to register if !CONFIG_CPU_IDLE
acpi pad driver kind of aggressively marks TSC as unstable at init
time, on mwait capable and non X86_FEATURE_NONSTOP_TSC systems. This is
irrespective of whether pad driver is ever going to be used on the
system or deep C-states are supported/used. This will affect every user
who just happens to compile in (or get a kernel version which
compiles in) acpi pad driver.
Move mark_tsc_unstable() out of init to the actual idle invocation path
of the pad driver.
There is also another bug/missing_feature in the code that it does not
support 'always running apic timer' and switches to broadcast mode
unconditionally. Shaohua, can you take a look at that please.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/sleep.h:3: WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_enter_[simple,bm] does
idle timing in ns, convert it to timeval, then to us, then to
pmtimer_ticks and then back to ns.
This patch changes things to
idle timing in ns, convert it to us, and then to pmtimer_ticks.
Just saves an imul along this path, but makes the code cleaner.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This EXPERIMENTAL driver supersedes acpi_idle on
Intel Atom Processors, Intel Core i3/i5/i7 Processors
and associated Intel Xeon processors.
It does not support the Intel Core2 processor or earlier.
For kernels configured with ACPI, CONFIG_INTEL_IDLE=y
allows intel_idle to probe before the ACPI processor driver.
Booting with "intel_idle.max_cstate=0" disables intel_idle
and the system will fall back on ACPI's "acpi_idle".
Typical Linux distributions load ACPI processor module early,
making CONFIG_INTEL_IDLE=m not easily useful on ACPI platforms.
intel_idle probes all processors at module_init time.
Processors that are hot-added later will be limited
to using C1 in idle.
Signed-off-by: Len Brown <len.brown@intel.com>
commit d306ebc286
(ACPI: Be in TS_POLLING state during mwait based C-state entry)
fixed an important power & performance issue where ACPI c2 and c3 C-states
were clearing TS_POLLING even when using MWAIT (ACPI_STATE_FFH).
That bug had been causing us to receive redundant scheduling interrups
when we had already been woken up by MONITOR/MWAIT.
Following up on that...
In the MWAIT case, we don't have to subsequently
check need_resched(), as that c heck was there
for the TS_POLLING-clearing case.
Note that not only does the cpuidle calling function
already check need_resched() before calling us, the
low-level entry into monitor/mwait calls it twice --
guaranteeing that a write to the trigger address
can not go un-noticed.
Also, in this case, we don't have to set TS_POLLING
when we wake, because we never cleared it.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
api_pad exclusively uses MONITOR/MWAIT to sleep in idle,
so it does not need the wakeup IPI during idle sleep
that is provoked by clearing TS_POLLING.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Shaohua Li <shaohua.li@intel.com>
The ACPI driver would fail probe when it found that
another driver had previously registered with cpuidle.
But this is a natural situation, as a native hardware
cpuidle driver should be able to bind instead of ACPI,
and the ACPI processor driver should be able to handle
yielding control of C-states while still handling
P-states and T-states.
Add a KERN_DEBUG line showing when acpi_idle
does successfully register.
Signed-off-by: Len Brown <len.brown@intel.com>
When the user passes the kernel parameter acpi_enforce_resources=lax,
the ACPI resources are no longer protected, so a native driver can
make use of them. In that case, we do not want the asus_atk0110 to be
loaded. Unfortunately, this driver loads automatically due to its
MODULE_DEVICE_TABLE, so the user ends up with two drivers loaded for
the same device - this is bad.
So I suggest that we prevent the asus_atk0110 driver from loading if
acpi_enforce_resources=lax.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Remove own implementation of hex_to_bin().
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These were used before cpuidle by the native ACPI idle driver,
which tracked promotion and demotion between states.
The code was referenced by CONFIG_ACPI_PROCFS
for /proc/acpi/processor/*/power,
but as we no longer do promotion/demotion, that
reference has been a NOP since the transition.
Signed-off-by: Len Brown <len.brown@intel.com>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (22 commits)
ACPI: fix early DSDT dmi check warnings on ia64
ACPICA: Update version to 20100428.
ACPICA: Update/clarify some parameter names associated with acpi_handle
ACPICA: Rename acpi_ex_system_do_suspend->acpi_ex_system_do_sleep
ACPICA: Prevent possible allocation overrun during object copy
ACPICA: Split large file, evgpeblk
ACPICA: Add GPE support for dynamically loaded ACPI tables
ACPICA: Clarify/rename some root table descriptor fields
ACPICA: Update version to 20100331.
ACPICA: Minimize the differences between linux GPE code and ACPICA code base
ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT
ACPICA: Update DSDT copy/detection.
ACPICA: Add subsystem option to force copy of DSDT to local memory
ACPICA: Add detection of corrupted/replaced DSDT
ACPICA: Add write support for DataTable operation regions
ACPICA: Fix for acpi_reallocate_root_table for incorrect root table copy
ACPICA: Update comments/headers, no functional change
ACPICA: Update version to 20100304
ACPICA: Fix for possible fault in acpi_ex_release_mutex
ACPICA: Standardize integer output for ACPICA warnings/errors
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
kasprintf combines kmalloc and sprintf, and takes care of the size
calculation itself.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression a,flag;
expression list args;
statement S;
@@
a =
- \(kmalloc\|kzalloc\)(...,flag)
+ kasprintf(flag,args)
<... when != a
if (a == NULL || ...) S
...>
- sprintf(a,args);
// </smpl>
[akpm@linux-foundation.org: don't change handling of `count']
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
WARNING: at drivers/firmware/dmi_scan.c:423 dmi_matches+0x70/0x160()
dmi check: not initialized yet.
This is caused by commit aa2110c
(ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT).
DMI is not initialized yet in acpi_early_init on ia64.
The DSDT DMI check table is x86 specific, so make it empty on other archs.
And this fixes the warnings on ia64.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some hardware error injection needs parameters, for example, it is
useful to specify memory address and memory address mask for memory
errors.
Some BIOSes allow parameters to be specified via an unpublished
extension. This patch adds support to it. The parameters will be
ignored on machines without necessary BIOS support.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ERST is a way provided by APEI to save and retrieve hardware error
record to and from some simple persistent storage (such as flash).
The Linux kernel support implementation is quite simple and workable
in NMI context. So it can be used to save hardware error record into
flash in hardware error exception or NMI handler, where other more
complex persistent storage such as disk is not usable. After saving
hardware error records via ERST in hardware error exception or NMI
handler, the error records can be retrieved and logged into disk or
network after a clean reboot.
For more information about ERST, please refer to ACPI Specification
version 4.0, section 17.4.
This patch incorporate fixes from Jin Dongming.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
CC: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Generic Hardware Error Source provides a way to report platform
hardware errors (such as that from chipset). It works in so called
"Firmware First" mode, that is, hardware errors are reported to
firmware firstly, then reported to Linux by firmware. This way, some
non-standard hardware error registers or non-standard hardware link
can be checked by firmware to produce more valuable hardware error
information for Linux.
Now, only SCI notification type and memory errors are supported. More
notification type and hardware error type will be added later. These
memory errors are reported to user space through /dev/mcelog via
faking a corrected Machine Check, so that the error memory page can be
offlined by /sbin/mcelog if the error count for one page is beyond the
threshold.
On some machines, Machine Check can not report physical address for
some corrected memory errors, but GHES can do that. So this simplified
GHES is implemented firstly.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
CPER stands for Common Platform Error Record, it is the hardware error
record format used to describe platform hardware error by various APEI
tables, such as ERST, BERT and HEST etc.
For more information about CPER, please refer to Appendix N of UEFI
Specification version 2.3.
This patch mainly includes the data structure difinition header file
used by other files.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Hardware Error Device (PNP0C33) is used to report some hardware errors
notified via SCI, mainly the corrected errors. Some APEI Generic
Hardware Error Source (GHES) may use SCI on hardware error device to
notify hardware error to kernel.
After receiving notification from ACPI core, it is forwarded to all
listeners via a notifier chain. The listener such as APEI GHES should
check corresponding error source for new events when notified.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
EINJ provides a hardware error injection mechanism, this is useful for
debugging and testing of other APEI and RAS features.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
