The fixed-regulator bindings require a separate property enable-active-high,
the standard gpio phandle property polarity setting is ignored.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 4fe69a934b ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add CAN support for Phytec phyFLEX-i.MX6 (PFL-A-02 and PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add PCIe support for Phytec phyFLEX-i.MX6 (PFL-A-02 and PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PMIC interrupt was changed from modul revision 1 to 2. Revision 1 was
declared as a prototype and is not in series by any customers.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The nand is on the module (PFL-A-02) and not on the baseboard (PBA-B-01).
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since pins and frequency are specific to module (pfla02), not base board
(pbab02), it is better to be initialized in corresponding dts file.
This patch fixes i2c2, i2c3 pin configuration which caused messages:
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c2grp
imx6q-pinctrl 20e0000.iomuxc: no groups defined in /soc/aips-bus@02000000/iomuxc@020e0000/i2c3grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c2grp
imx6q-pinctrl 20e0000.iomuxc: unable to find group for node i2c3grp
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.
Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.
This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The 2.5V VDD_ETH_IO voltage supplied by the DA9063 LDO4 is used
to power the KSZ9031 PHY DVDDH input and to pull the necessary
pins (including bootstrap pins) high.
It also powers the i.MX6 NVCC_RGMII and NVCC_ENET inputs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The pins labeled UART1 on the module connector are wired to i.MX6 uart3.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Note that the fec driver code currently hard-codes an active-low
reset, regardless of the flags in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch enables the red and green GPIO LEDs on Phytec phyFLEX i.MX6 modules.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
