The currently formula has been taken from the 88AP510 SoC datasheet,
which is not exactly correct. The correct value for the temperature
in Celcius of the sensor present in this SoC is:
Celsius = (322-reg)/1.3625
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The correct value is obtain by first shifting the register by the offset,
later applying the valid mask and finally invert the result.
This check was lacking an extra parenthesis to be strictly correct.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
thermal_zone_device_register() returns ERR_PTR on error, thus use
IS_ERR rather than IS_ERR_OR_NULL to check return value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
cpufreq cooling uses different frequencies as different cooling states.
But the per_cpu cpufreq_frequency_table may contain duplicate,
invalid entries, and it may be in either ascending or descending order.
And currently, code for parsing the per_cpu cpufreq_frequency_table
is used in several places and inconsistent.
Now introduce new code to
1. get the maximum cooling states
2. translate cooling state to cpu frequency
3. translate cpu frequency to cooling state
in one place,
with the correct logic of handling per_cpu cpufreq_frequency_table.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Amit Daniel kachhap <amit.daniel@samsung.com>
we are returning EINVAL while the thermal_zone_device_register function fail.
instead we can use the return value from the thermal_zone_device_register by
using PTR_ERR.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
thermal_zone_device_register returns a value contained in the pointer itself
use PTR_ERR to obtain the address and return it at the end.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add the missing unlock before return from function rcar_thermal_update_temp()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The new intel_powerclamp thermal cooling device driver was merged in
commit 2af78448ff (Pull thermal management updates from Zhang Rui)
without any data conflicts. But there was a more subtle conflict I
missed: the driver uses MAX_USER_RT_PRIO, but commit 8bd75c77b7
("sched/rt: Move rt specific bits into new header file") had moved that
define from <linux/sched.h> to <linux/sched/rt.h>.
Which caused this build failure:
drivers/thermal/intel_powerclamp.c: In function ‘clamp_thread’:
drivers/thermal/intel_powerclamp.c:360:21: error: ‘MAX_USER_RT_PRIO’ undeclared (first use in this function)
drivers/thermal/intel_powerclamp.c:360:21: note: each undeclared identifier is reported only once for each function it appears in
And because I don't do a full "make allmodconfig" build after each pull,
I didn't notice until too late. So now the fix is here, separately from
the merge commit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull thermal management updates from Zhang Rui:
"Highlights:
- introduction of Dove thermal sensor driver.
- introduction of Kirkwood thermal sensor driver.
- introduction of intel_powerclamp thermal cooling device driver.
- add interrupt and DT support for rcar thermal driver.
- add thermal emulation support which allows platform thermal driver
to do software/hardware emulation for thermal issues."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
thermal: rcar: remove __devinitconst
thermal: return an error on failure to register thermal class
Thermal: rename thermal governor Kconfig option to avoid generic naming
thermal: exynos: Use the new thermal trend type for quick cooling action.
Thermal: exynos: Add support for temperature falling interrupt.
Thermal: Dove: Add Themal sensor support for Dove.
thermal: Add support for the thermal sensor on Kirkwood SoCs
thermal: rcar: add Device Tree support
thermal: rcar: remove machine_power_off() from rcar_thermal_notify()
thermal: rcar: add interrupt support
thermal: rcar: add read/write functions for common/priv data
thermal: rcar: multi channel support
thermal: rcar: use mutex lock instead of spin lock
thermal: rcar: enable CPCTL to use hardware TSC deciding
thermal: rcar: use parenthesis on macro
Thermal: fix a build warning when CONFIG_THERMAL_EMULATION cleared
Thermal: fix a wrong comment
thermal: sysfs: Add a new sysfs node emul_temp for thermal emulation
PM: intel_powerclamp: off by one in start_power_clamp()
thermal: exynos: Miscellaneous fixes to support falling threshold interrupt
...
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 76cc18874 "thermal: rcar: add Device Tree support"
added device tree support for this driver, but also added
an instance of __devinitconst, which is no longer defined
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Zhang Rui <rui.zhang@intel.com>
The return code from the registration of the thermal class is used to
unallocate resources, but this failure isn't passed back to the caller of
thermal_init. Return this failure back to the caller.
This bug was introduced in changeset 4cb18728 which overwrote the return code
when the variable was re-used to catch the return code of the registration of
the genetlink thermal socket family.
Signed-off-by: Richard Guy Briggs <rbriggs@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently, we have three Kconfig options for thermal governors, aka,
CONFIG_FAIR_SHARE, CONFIG_USER_SPACE and CONFIG_STEP_WISE.
But these names are too generic that may bring confusion to users.
Rename them to CONFIG_THERMAL_GOV_FAIR_SHARE,
CONFIG_THERMAL_GOV_USER_SPACE, CONFIG_THERMAL_GOV_STEP_WISE
to avoid the generic naming.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch uses the quick thermal cooling trend type macros. This is needed
as exynos5 and other thermal sensors now supports only interrupt method for
thresold temperature check.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch introduces using temperature falling interrupt in exynos
thermal driver. Former patch, it only use polling way to check
whether if system themperature is fallen. However, exynos SOC also
provides temperature falling interrupt way to do same things by hw.
This feature is not supported in exynos4210.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Marvell Dove SoC has a thermal sensor. Add a driver using the
thermal framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support for Kirkwood 88F6282 and 88F6283 thermal sensor.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Support for loading the Renesas R-Car thermal module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Machine/System power-off is run in thermal frame work if
it become critical temperature.
This patch removed pointless machine_power_off()
from thermal_zone_device_ops :: .notify
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds interrupt support for R-Car thermal driver.
New generation R-Car thermal sensor interrupt controller was
different from old generation.
This patch supports new generation sensor only,
since the old generation interrupt controller had never been used before,
and will never be used in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
R-Car thermal driver will use struct common in next
feature (interrupt support).
But the register address is different between struct priv and common.
This patch adds read/write functions for struct common,
and use macro technique to avoid wrong register access.
This is preparation patch for next feature (interrupt support),
therefore, there is no user to use this common read/write
function at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
R-Car thermal sensor will be multi channel sensor in next generation.
But "IRQ controlling method" and "register mapping" are
different between old/new chip.
This patch adds multi sensor support.
Then, this driver assumes there is common register
if platform has IRQ resource.
The IRQ will be supported soon.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Current R-Car thermal driver is using spin lock for each
registers read/write, but it is pointless lock.
This lock is required while reading temperature,
but it needs long wait (= 300ms).
So, this patch used mutex lock while reading temperature,
instead of spin lock for each registers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
If CPCTL was 1 on R-Car thermal, the thermal comparator offset
is automatically decided by hardware.
And this CPCTL is the conditions which validate interrupt.
This patch enabled CPCTL.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
"level" parameter of get_cpu_frequency equals cooling state
of cpu cooling device, and it starts from 0.
Fix the misleading comment.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support to set the emulated temperature method in
thermal zone (sensor). After setting this feature thermal zone may
report this temperature and not the actual temperature. The emulation
implementation may be based on sensor capability through platform
specific handler or pure software emulation if no platform handler defined.
This is useful in debugging different temperature threshold and its
associated cooling action. Critical threshold's cannot be emulated.
Writing 0 on this node should disable emulation.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This value has already been clamped correctly to 0 through 49 in
powerclamp_set_cur_state() so this patch doesn't actually change
anything. But we should fix it anyway for consistency.
set_target_ratio is used as an offset into an array with
MAX_TARGET_RATIO (50) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Below fixes are done to support falling threshold interrupt,
* Falling interrupt status macro corrected according to exynos5 data sheet.
* The get trend function modified to calculate trip temperature correctly.
* The clearing of interrupt status in the isr is now done after handling
the event that caused the interrupt.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Intel PowerClamp driver performs synchronized idle injection across
all online CPUs. The goal is to maintain a given package level C-state
ratio.
Compared to other throttling methods already exist in the kernel,
such as ACPI PAD (taking CPUs offline) and clock modulation, this is often
more efficient in terms of performance per watt.
Please refer to Documentation/thermal/intel_powerclamp.txt for more details.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an extra check in the data structure while registering
a thermal device. The check is to avoid registering zones with a number
of trips greater than zero, but with no .get_trip_temp nor .get_trip_type
callbacks. Receiving such data structure may end in wrong data access.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
No need for spinlocks in this file, then removing its header.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch changes the function thermal_generate_netlink_event
to receive a thermal zone device instead of a originator id.
This way, the messages will always be bound to a thermal zone.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Hongbo Zhang <hongbo.zhang@stericsson.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Hongbo Zhang <hongbo.zhang@stericsson.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_clk_get allocates a resource that is released when a driver detaches.
This patch uses devm_clk_get for data that is allocated in the probe
function of a platform device and is only released in the remove function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds .get_trip_type(), .get_trip_temp(), and .notify()
on rcar_thermal_zone_ops.
Driver will try platform power OFF if it reached to
critical temperature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch supports exynos's emulation mode with newly created sysfs node.
Exynos 4x12 (4212, 4412) and 5 series provide emulation mode for thermal
management unit. Thermal emulation mode supports software debug for TMU's
operation. User can set temperature manually with software code and TMU
will read current temperature from user value not from sensor's value.
This patch includes also documentary placed under Documentation/thermal/.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
step_wise governor should set the device cooling state to
upper/lower limit directly when THERMAL_TREND_RAISE/DROP_FULL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
This patch adds rcar_zone_to_priv()
which is a helper macro for gettign private data.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The unit of temperature is Milli-Celsius.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
As thermal drivers can be built as modules and also
the thermal framework itself, building cpu cooling
only as built-in can cause linking errors. For instance:
* Generic Thermal sysfs driver
*
Generic Thermal sysfs driver (THERMAL) [M/n/y/?] m
generic cpu cooling support (CPU_THERMAL) [N/y/?] (NEW) y
with the following drive:
CONFIG_OMAP_BANDGAP=m
generates:
ERROR: "cpufreq_cooling_unregister" [drivers/staging/omap-thermal/omap-thermal.ko] undefined!
ERROR: "cpufreq_cooling_register" [drivers/staging/omap-thermal/omap-thermal.ko] undefined!
This patch changes cpu cooling driver to allow it
to be built as module.
Reported-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There are predefined cpu_masks that are const data structures.
This patch changes the cpu cooling register function so that
those const cpu_masks can be used, without compilation warnings.
include/linux/cpumask.h
* The following particular system cpumasks and operations manage
* possible, present, active and online cpus.
*
* cpu_possible_mask- has bit 'cpu' set iff cpu is populatable
* cpu_present_mask - has bit 'cpu' set iff cpu is populated
* cpu_online_mask - has bit 'cpu' set iff cpu available to scheduler
* cpu_active_mask - has bit 'cpu' set iff cpu available to migration
*
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This driver is based on the thermal management framework in thermal_sys.c. A
thermal zone device is created with the trip points to which cooling devices
can be bound, the current cooling device is cpufreq, e.g. CPU frequency is
clipped down to cool the CPU, and other cooling devices can be added and bound
to the trip points dynamically. The platform specific PRCMU interrupts are
used to active thermal update when trip points are reached.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Francesco Lavra <francescolavra.fl@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Silences the following sparse warning:
drivers/thermal/cpu_cooling.c:67:31: warning:
symbol 'notify_device' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Problem of using this list is that the cpufreq_get_max_state callback will be
called when register cooling device by thermal_cooling_device_register, but
this list isn't ready at this moment. What's more, there is no need to maintain
such a list, we can get cpufreq_cooling_device instance by the private
thermal_cooling_device.devdata.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Francesco Lavra <francescolavra.fl@gmail.com>
Reviewed-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In the while loop for counting cpu frequencies, if table[i].frequency equals
CPUFREQ_ENTRY_INVALID, index i won't be increased, so this leads to an endless
loop, what's more the index i cannot be referred as cpu frequencies number if
there is CPUFREQ_ENTRY_INVALID case.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The curly bracket should be aligned with corresponding if else statements.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_kfree and devm_iounmap should not have to be explicitly used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Fixes the following sparse warnings:
drivers/thermal/user_space.c:38:5: warning:
symbol 'notify_user_space' was not declared. Should it be static?
drivers/thermal/user_space.c:46:25: warning:
symbol 'thermal_gov_user_space' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Fixes the following sparse warnings:
drivers/thermal/fair_share.c:80:5: warning:
symbol 'fair_share_throttle' was not declared. Should it be static?
drivers/thermal/fair_share.c:111:25: warning:
symbol 'thermal_gov_fair_share' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Fixes the following sparse warnings:
drivers/thermal/step_wise.c:153:5: warning:
symbol 'step_wise_throttle' was not declared. Should it be static?
drivers/thermal/step_wise.c:172:25: warning:
symbol 'thermal_gov_step_wise' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch fixes the following mutex and NULL pointer
problems in thermal_sys.c:
* mutex_unlock fix in update_temperature function
* mutex_unlock fix in bind_cdev function
* Correct early return to continue in bind_cdev function
* NULL check fix in bind_cdev function
* NULL check fix in bind_tz function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch provides option to choose the default thermal
governor. If no option is provided, the step_wise
governor is selected by default.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds a notification API which the sensor drivers'
can use to notify the framework. The framework then takes
care of the throttling according to the configured policy.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch removes the throttling logic out of
thermal_sys.c; also refactors the code into smaller
functions so that are easy to read/maintain.
* Seperates the handling of critical and non-critical trips
* Re-arranges the set_polling and device_check methods, so
that all related functions are arranged in one place.
* Removes the 'do_update' and 'trip_update' method, as part
of moving the throttling logic out of thermal_sys.c
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch registers a governor which will let the
user land manage the platform thermals. Whenever a
trip happens, this governor just notifies the user
space using kobj_uevent().
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds a simple step_wise governor to the
generic thermal layer. This algorithm throttles the
cooling devices in a linear fashion. If the 'trend'
is heating, it throttles by one step. And if the
thermal trend is cooling it de-throttles by one step.
This actually moves the throttling logic from thermal_sys.c
and puts inside step_wise.c, without any change.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch introduces a simple 'weight' based
governor named fair_share governor. Whenever the
thermal framework gets notified of the trip point
violation, this governor (if configured), throttles
the cooling devices associated with a thermal zone.
This mapping between a thermal zone and a cooling device
and the effectiveness of cooling are provided in the
platform layer.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch makes the thermal_cdev_update function as a
global one, so that other files can use it. This function
serves as a single arbitrator to set the state of a cooling
device.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch updates the binding logic in thermal_sys.c
It uses the platform layer data to bind a thermal zone
to a cdev for a particular trip point.
* If we do not have platform data and do not have
.bind defined, do not bind.
* If we do not have platform data but .bind is
defined, then use tz->ops->bind.
* If we have platform data, use it to create binding.
The same logic sequence is followed for unbind also.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds a policy sysfs attribute to a thermal zone.
This attribute denotes the throttling governor used for the
zone. This is a RW attribute.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch creates a structure to hold platform
thermal governor information, and provides APIs
for individual thermal governors to register/unregister
with the Thermal framework.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds the thermal zone parameter as an argument to
the tzd_register() function call; and updates other drivers
using this function.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds the following API's to thermal_sys.c, that
can be used by other Thermal drivers.
* get_tz_trend: obtain the trend of the given thermal zone
* get_thermal_instance: obtain the instance corresponding
to the given tz, cdev and the trip point.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch creates a thermal_core.h file which can contain
all defines used by the core thermal framework files. For
now, move the thermal_instance structure to thermal_core.h
This structure is used by files under drivers/thermal/.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
following were the errors reported
drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2
with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0236141837 ("thermal: add generic cpufreq cooling
implementation") requires cpufreq_frequency_get_table(), but that
function is only defined for CONFIG_CPU_FREQ_TABLE resulting in the
following build error:
drivers/built-in.o: In function `cpufreq_get_max_state':
drivers/thermal/cpu_cooling.c:259: undefined reference to `cpufreq_frequency_get_table'
drivers/built-in.o: In function `get_cpu_frequency':
drivers/thermal/cpu_cooling.c:129: undefined reference to `cpufreq_frequency_get_table'
Fix it by selecting CONFIG_CPU_FREQ_TABLE for such a configuration.
It turns out CONFIG_EXYNOS_THERMAL also needs CONFIG_CPU_FREQ_TABLE, so
select it there as well.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
To avoid name conflicts:
drivers/video/riva/fbdev.c:281:9: sparse: preprocessor token MAX_LEVEL redefined
While at it, also make the other names more consistent and add
parentheses.
[akpm@linux-foundation.org: repair fallout]
[sfr@canb.auug.org.au: IB/mlx4: fix for MAX_ID_MASK to MAX_IDR_MASK name change]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: walter harms <wharms@bfs.de>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
exynos_unregister_thermal() is functional only when 'th_zone' is not
NULL (ensured by the NULL checks). However, in the event it is NULL, it
gets dereferenced in the for loop. This patch fixes this issue.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
This patch fixes small bug on cpu_cooling. CPU cooling device has own
id generated with idr mathod. However in the previous version, it swapped
to all same id at last stage of probing as 0. This makes id's collision and
also occures error when it releases that id.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
devm_* functions are used to replace kzalloc, request_mem_region, ioremap
and request_irq functions in probe call. With the usage of devm_* functions
explicit freeing and unmapping is not required.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add necessary default platform data support needed for TMU driver. The
supplied dt/non-dt values are tested for origen exynos4210 and smdk exynos5250
platforms and only compile tested for exynos4412.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: jonghwa lee <jonghwa3.lee@samsung.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This code added creates a link between temperature sensors, linux thermal
framework and cooling devices for samsung exynos platform. This layer
monitors the temperature from the sensor and informs the generic thermal
layer to take the necessary cooling action.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Insert exynos5 TMU sensor changes into the thermal driver. Some exynos4
changes are made generic for exynos series.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: SangWook Ju <sw.ju@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patchset introduces a new generic cooling device based on cpufreq
that can be used on non-ACPI platforms. As a proof of concept, we have
drivers for the following platforms using this mechanism now:
* Samsung Exynos (Exynos4 and Exynos5) in the current patchset.
* Freescale i.MX (git://git.linaro.org/people/amitdanielk/linux.git imx6q_thermal)
There is a small change in cpufreq cooling registration APIs, so a minor
change is needed for Freescale platforms.
Brief Description:
1) The generic cooling devices code is placed inside driver/thermal/*
as placing inside acpi folder will need un-necessary enabling of acpi
code. This code is architecture independent.
2) This patchset adds generic cpu cooling low level implementation
through frequency clipping. In future, other cpu related cooling
devices may be added here. An ACPI version of this already exists
(drivers/acpi/processor_thermal.c) .But this will be useful for
platforms like ARM using the generic thermal interface along with the
generic cpu cooling devices. The cooling device registration API's
return cooling device pointers which can be easily binded with the
thermal zone trip points. The important APIs exposed are,
a) struct thermal_cooling_device *cpufreq_cooling_register(
struct cpumask *clip_cpus)
b) void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
3) Samsung exynos platform thermal implementation is done using the
generic cpu cooling APIs and the new trip type. The temperature sensor
driver present in the hwmon folder(registered as hwmon driver) is moved
to thermal folder and registered as a thermal driver.
A simple data/control flow diagrams is shown below,
Core Linux thermal <-----> Exynos thermal interface <----- Temperature Sensor
| |
\|/ |
Cpufreq cooling device <---------------
TODO:
*Will send the DT enablement patches later after the driver is merged.
This patch:
Add support for generic cpu thermal cooling low level implementations
using frequency scaling up/down based on the registration parameters.
Different cpu related cooling devices can be registered by the user and
the binding of these cooling devices to the corresponding trip points can
be easily done as the registration APIs return the cooling device pointer.
The user of these APIs are responsible for passing clipping frequency .
The drivers can also register to recieve notification about any cooling
action called.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The type parameter in thermal_zone_device_register and
thermal_cooling_device_register can be NULL, indicating that no sysfs attribute
for the type should be created. Only call strlen() and strcpy() on type if it is
not NULL.
This patch addresses Coverity #102180 and #102182: Dereference before null check
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch add basic Renesas R-Car thermal sensor support.
It was tested on R-Car H1 Marzen board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
temp_crit.name and temp_input.name have a length of 16 bytes. Using
THERMAL_NAME_LENGTH (20) as length parameter for snprintf() may result in
out-of-bounds memory accesses. Replace it with sizeof().
Addresses Coverity #115679
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
we need to go over all the thermal_instance list of a cooling device
to decide which cooling state to put the cooling device to.
But at this time, as a cooling device may be referenced in multiple
thermal zones, we need to lock the list first in case
another thermal zone is updating this cooling device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Remove thermal_zone_device_passive(). And use
thermal_zone_trip_update() and thermal_zone_do_update()
for both active and passive cooling.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This fixes the problem that a cooling device may be referenced by
by multiple trip points in multiple thermal zones.
With this patch, we have two stages for updating a thermal zone,
1. check if a thermal_instance needs to be updated or not
2. update the cooling device, based on the target cooling state
of all its instances.
Note that, currently, the cooling device is set to the deepest
cooling state required.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
List thermal_instance in thermal_cooling_device so that
cooling device can know the cooling state requirement
of all the thermal instances.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
thermal_instance should be referenced by both thermal zone devices
and thermal cooling devices.
Rename thermal_instance.node to thermal_instance.tz_node in this patch
and thermal_instanace.cdev_node will be introduced in next patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Rename thermal_zone_device.cooling_devices
to thermal_zone_device.thermal_instances
thermal_zone_device.cooling_devices is not accurate
as this is a list for thermal instances, rather than cooling devices.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This struct is used to describe the behavior for a thermal
cooling device on a certain trip point for a certain thremal zone.
thermal_cooling_device_instance is not accurate, as a cooling device
can be used for more than one trip point in one thermal zone device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This function is used to update the cooling state of
all the cooling devices that are bound to an active trip point.
This will be used for passive cooling as well, in the future patches.
as both active and passive cooling can share the same algorithm,
which is
1. if the temperature is higher than a trip point,
a. if the trend is THERMAL_TREND_RAISING, use higher cooling
state for this trip point
b. if the trend is THERMAL_TREND_DROPPING, use lower cooling
state for this trip point
2. if the temperature is lower than a trip point, use lower
cooling state for this trip point.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Remove tc1/tc2 in generic thermal layer.
.get_trend() callback starts to take effect from this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
According to ACPI spec, tc1 and tc2 are used by OSPM
to anticipate the temperature trends.
We introduced the same concept to the generic thermal layer
for passive cooling, but now it seems that these values
are hard to be used on other platforms.
So We introduce .get_trend() as a more general solution.
For the platform thermal drivers that have their own way to
anticipate the temperature trends, they should provide
their own .get_trend() callback.
Or else, we will calculate the temperature trends by simply
comparing the current temperature and the cached previous
temperature reading.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
set upper and lower limits when binding
a thermal cooling device to a thermal zone device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
As the active cooling devices can have multiple cooling states,
we may want only several cooling states for a certain trip point,
and other cooling states for other active trip points.
To do this, we should be able to describe the cooling device
behavior for a certain trip point, rather than for the entire thermal zone.
And when updating thermal zone, we need to check the upper and lower limit
to make sure the cooling device is set to the proper cooling state.
Note that this patch will not bring any different behavior as
upper limit is set to max_state and lower limit is set to 0
in this patch, for now.
Next patch will set these to real values.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
This is because general active cooling devices, like fans,
may have multiple speeds, which can be mapped to different cooling states.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
Convert delayed_work users doing cancel_delayed_work() followed by
queue_delayed_work() to mod_delayed_work().
Most conversions are straight-forward. Ones worth mentioning are,
* drivers/edac/edac_mc.c: edac_mc_workq_setup() converted to always
use mod_delayed_work() and cancel loop in
edac_mc_reset_delay_period() is dropped.
* drivers/platform/x86/thinkpad_acpi.c: No need to remember whether
watchdog is active or not. @fan_watchdog_active and related code
dropped.
* drivers/power/charger-manager.c: Seemingly a lot of
delayed_work_pending() abuse going on here.
[delayed_]work_pending() are unsynchronized and racy when used like
this. I converted one instance in fullbatt_handler(). Please
conver the rest so that it invokes workqueue APIs for the intended
target state rather than trying to game work item pending state
transitions. e.g. if timer should be modified - call
mod_delayed_work(), canceled - call cancel_delayed_work[_sync]().
* drivers/thermal/thermal_sys.c: thermal_zone_device_set_polling()
simplified. Note that round_jiffies() calls in this function are
meaningless. round_jiffies() work on absolute jiffies not delta
delay used by delayed_work.
v2: Tomi pointed out that __cancel_delayed_work() users can't be
safely converted to mod_delayed_work(). They could be calling it
from irq context and if that happens while delayed_work_timer_fn()
is running, it could deadlock. __cancel_delayed_work() users are
dropped.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Roland Dreier <roland@kernel.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that is)
caught the issue and it was decided[1] that I'd just delay the battery
pull request, and then will fix it up by merging upstream back into
battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem was
needed to get rid of a warning in power supply subsystem (the warning
was not drivers/power's "fault", the thermal registration function just
needed a proper const annotation, which is also done by a small commit
on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=1NaS
-----END PGP SIGNATURE-----
Merge tag 'for-v3.6' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"The tag contains just a few battery-related changes for v3.6. It's is
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that
is) caught the issue and it was decided[1] that I'd just delay the
battery pull request, and then will fix it up by merging upstream back
into battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem
was needed to get rid of a warning in power supply subsystem (the
warning was not drivers/power's "fault", the thermal registration
function just needed a proper const annotation, which is also done by
a small commit on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28"
* tag 'for-v3.6' of git://git.infradead.org/battery-2.6: (23 commits)
thermal: Constify 'type' argument for the registration routine
olpc-battery: update CHARGE_FULL_DESIGN property for BYD LiFe batteries
olpc-battery: Add VOLTAGE_MAX_DESIGN property
charger-manager: Fix build break related to EXTCON
lp8727_charger: Move header file into platform_data directory
power_supply: Add min/max alert properties for CAPACITY, TEMP, TEMP_AMBIENT
bq27x00_battery: Add support for BQ27425 chip
charger-manager: Set current limit of regulator for over current protection
charger-manager: Use EXTCON Subsystem to detect charger cables for charging
test_power: Add VOLTAGE_NOW and BATTERY_TEMP properties
test_power: Add support for USB AC source
gpio-charger: Use cansleep version of gpio_set_value
bq27x00_battery: Add support for power average and health properties
sbs-battery: Don't trigger false supply_changed event
twl4030_charger: Allow charger to control the regulator that feeds it
twl4030_charger: Add backup-battery charging
twl4030_charger: Fix some typos
max17042_battery: Support CHARGE_COUNTER power supply attribute
smb347-charger: Add constant charge and current properties
power_supply: Add constant charge_current and charge_voltage properties
...
thermal_zone_device_register() does not modify 'type' argument, so it is
safe to declare it as const. Otherwise, if we pass a const string, we are
getting the ugly warning:
CC drivers/power/power_supply_core.o
drivers/power/power_supply_core.c: In function 'psy_register_thermal':
drivers/power/power_supply_core.c:204:6: warning: passing argument 1 of 'thermal_zone_device_register' discards 'const' qualifier from pointer target type [enabled by default]
include/linux/thermal.h:140:29: note: expected 'char *' but argument is of type 'const char *'
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
The Linux Thermal Framework does not support hysteresis
attributes. Most thermal sensors, today, have a
hysteresis value associated with trip points.
This patch adds hysteresis attributes on a per-trip-point
basis, to the Thermal Framework. These attributes are
optionally writable.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some of the thermal drivers using the Generic Thermal Framework
require (all/some) trip points to be writeable. This patch makes
the trip point temperatures writeable on a per-trip point basis,
and modifies the required function call in thermal.c. This patch
also updates the Documentation to reflect the new change.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
SPEAr platforms now support DT and so must convert all drivers to support
DT. This patch adds DT probing support for SPEAr thermal sensor driver
and updates its documentation too.
Also, as SPEAr is the only user of this driver and is only available with
DT, make this an only DT driver. So, platform_data is completely removed
and passed via DT now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Basically without this patch changing the mode of thermal zone
is not possible as wrong string size is passed to strncmp.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
thermal_zone_device_register() never returns NULL, on error it returns and
ERR_PTR().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
readl/writel versions for ARM contain memory barrier instruction for
synchronizing DMA buffers. These are not required at least on this
module. So use lighter _relaxed variants.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
ST's SPEAr13xx machines are based on CortexA9 ARM processors. These
machines contain a thermal sensor for junction temperature monitoring.
This patch adds support for this thermal sensor in existing thermal
framework.
[akpm@linux-foundation.org: little code cleanup]
[akpm@linux-foundation.org: print the pointer correctly]
[viresh.kumar@st.com: thermal/spear_thermal: add compilation dependency on PLAT_SPEAR]
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the current logging style.
Remove PREFIX, add pr_fmt, convert the printks. All dmesg output now
prefixed with "thermal_sys: ".
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Just a few tidies to make it more like most kernel sources.
A couple of long lines still remain.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
These don't add any value as they are used only once and the surrounding
code uses similar variable.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Line continations are not necessary in function calls or statements.
Remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
With CONFIG_NET=n:
drivers/thermal/thermal_sys.c:63: warning: 'thermal_event_seqnum' defined but not used
Move 'thermal_event_seqnum' definition inside the '#ifdef CONFIG_NET'
[akpm@linux-foundation.org: make thermal_event_seqnum local to generate_netlink_event()]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
It doesn't seem right for the thermal subsystem to export a symbol
named generate_netlink_event. This function is thermal-specific and
its name should reflect that fact. Rename it to
thermal_generate_netlink_event.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: R.Durgadoss <durgadoss.r@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The thermal driver should use a freezable workqueue to schedule
polling to prevent thermal_zone_device_update() from being run
during system suspend, when the devices it relies on may be inactive.
Make it use the system freezable workqueue for this purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
THERMAL_HWMON is implemented inside the thermal_sys driver and has no
effect on drivers implementing thermal zones, so they shouldn't see
anything related to it in <linux/thermal.h>. Making the THERMAL_HWMON
implementation fully internal has two advantages beyond the cleaner
design:
* This avoids rebuilding all thermal drivers if the THERMAL_HWMON
implementation changes, or if CONFIG_THERMAL_HWMON gets enabled or
disabled.
* This avoids breaking the thermal kABI in these cases too, which should
make distributions happy.
The only drawback I can see is slightly higher memory fragmentation, as
the number of kzalloc() calls will increase by one per thermal zone. But
I doubt it will be a problem in practice, as I've never seen a system with
more than two thermal zones.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rene Herman <rene.herman@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We'll soon need to reuse it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rene Herman <rene.herman@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
It's about time to revert 16d7523973 ("thermal: Create
CONFIG_THERMAL_HWMON=n"). Anybody running a kernel >= 2.6.40 would also
be running a recent enough version of lm-sensors.
Actually having CONFIG_THERMAL_HWMON is pretty convenient so instead of
dropping it, we keep it but hide it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rene Herman <rene.herman@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes two minor bugs in thermal_sys:
(a) The flow of goto's in thermal_hwmon_add_sysfs.
(b) Remove the temp*_crit only if there is a get_crit_temp defined, in
thermal_remove_hwmon_sysfs.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Several ACPI drivers fail to build if CONFIG_NET is unset, because
they refer to things depending on CONFIG_THERMAL that in turn depends
on CONFIG_NET. However, CONFIG_THERMAL doesn't really need to depend
on CONFIG_NET, because the only part of it requiring CONFIG_NET is
the netlink interface in thermal_sys.c.
Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET
and remove the dependency of CONFIG_THERMAL on CONFIG_NET from
drivers/thermal/Kconfig.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Luming Yu <luming.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds event notification support to the generic
thermal sysfs framework in the kernel. The notification is in the
form of a netlink event.
Signed-off-by: R.Durgadoss <durgadoss.r@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
And while touching that function definition do something about the disaster
of formatting there.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
state is unsigned long so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Otherwise polling will continue for the thermal zone even when
it is no longer needed, for example because forced passive cooling
was disabled.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Setting polling_delay is useless as passive_delay has priority,
so the value shown in proc isn't the actual polling delay. It
also gives the impression to the user that he can change the
polling interval through proc, while in fact he can't.
Also, unset passive_delay when the forced passive trip point is
unbound to allow polling to be disabled.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Values below 1000 milli-celsius don't make sense and can cause the
system to go into a thermal heart attack: the actual temperature
will always be lower and thus the system will be throttled down to
its lowest setting.
An additional problem is that values below 1000 will show as 0 in
/proc/acpi/thermal/TZx/trip_points:passive.
cat passive
0
echo -n 90 >passive
bash: echo: write error: Invalid argument
echo -n 90000 >passive
cat passive
90000
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Make the trip_point_N_type sysfs files return a string ending in EOL for
consistency with other sysfs files.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Otherwise THERMAL_HWMON can be selected when HWMON=n and THERMAL=n, which
fails to build.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The return value of the get_temp function is not checked when doing a
thermal zone update. This may lead to a critical shutdown if get_temp
fails and the content of the temp variable is incorrectly set higher than
the critical trip point.
This has been observed on a system with incorrect ACPI implementation
where the corresponding methods were not serialized and therefore
sometimes triggered ACPI errors (AE_ALREADY_EXISTS). The following
critical shutdowns indicated a temperature of 2097 C, which was obviously
wrong.
The patch adds a return value check that jumps over all trip point
evaluations printing a warning if get_temp fails. The trip points are
evaluated again on the next polling interval with successful get_temp
execution.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression caused by commit
b1569e99c7
"ACPI: move thermal trip handling to generic thermal layer"
which accidentally changed trip point trigger condition to
temp > trip_temp
This patch changes the trigger condition back to
temp >= trip_temp
Signed-off-by: Vladimir Zajac <eightgraph@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Due to poor thermal design or Linux driving hardware outside its thermal
envelope, some systems will reach critical temperature and shut down
under high load. This patch adds support for forcing a polling-based
passive trip point if the firmware doesn't provide one. The assumption
is made that the processor is the most practical means to reduce the
dynamic heat generation, so hitting the passive thermal limit will cause
the CPU to be throttled until the temperature stabalises around the
defined value.
UI is provided via a "passive" sysfs entry in the thermal zone
directory. It accepts a decimal value in millidegrees celsius, or "0" to
disable the functionality. Default behaviour is for this functionality
to be disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI code currently carries its own thermal trip handling, meaning that
any other thermal implementation will need to reimplement it. Move the code
to the generic thermal layer.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The thermal API currently uses strings to pass values to userspace. This
makes it difficult to use from within the kernel. Change the interface
to use integers and fix up the consumers.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
A bug in libsensors <= 2.10.6 is exposed
when this new hwmon I/F is enabled.
Create CONFIG_THERMAL_HWMON=n
until some time after libsensors 2.10.7 ships
so those users can run the latest kernel.
libsensors 3.x is already fixed -- those users
can use CONFIG_THERMAL_HWMON=y now.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add hwmon sys I/F for generic thermal driver.
Note: we have one hwmon class device for EACH TYPE of the thermal zone device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Build the generic thermal driver as module "thermal_sys".
Make ACPI thermal, video, processor and fan SELECT the generic
thermal driver, as these drivers rely on it to build the sysfs I/F.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The THERMAL_MAX_TRIPS value is set to 10. It is too few for the Compaq AP550
machine which has 12 trip points.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic thermal I/F gets selected by ACPI_THERMAL --
its only current customer.
it doesn't need to clutter other configs by default.
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 3152fb9f11.
This broke libsensors.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Need to return using ERR_PTR instead of NULL
in case of errors.
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added sanity check to make sure that thermal zone
and cooling device exists.
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Generic Thermal sysfs driver for thermal management.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
