Add the missing unregister for the mv88e6352_switch_driver.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).
Fixes: cca8b13375 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/mv88e6xxx.c: In function ‘mv88e6xxx_set_port_state’:
drivers/net/dsa/mv88e6xxx.c:905: warning: ‘ret’ may be used uninitialized in this function
If oldstate == state, mv88e6xxx_set_port_state() will return an
uninitialized value. Pre-initialize ret to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A duplicate declaration of 'ret' can result in hiding an error code.
Drop it.
Fixes: 17ee3e04dd ("net: dsa: Provide additional RMON statistics")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistic counters for the mv88e6172 never worked. This device is
a member of the 6352 family of chips, which has a slightly different
layout of the register used for capturing statistics. Add support for
detecting this family and poking the port in the right place in the
register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than refer to registers by number, define mnemonics. Also
define mnemonics for the commonly used bits within the registers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading the statistics from the hardware is the same for all
chips. What differs is the number of available statistics. Have just
one copy of the code in the shared mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mutex should be held while reading and writing to the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the common code for reading and writing phy registers into the
shared mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions could in future be used by other drivers. Move them
into the shared area.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell switches are all reset in nearly the same way. The only
difference is if the PPU should be enabled or not. Move this
code into the shared mv88x6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a step towards consolidating code, consistently set the
number of ports in the private state structure, and make use of it in
loops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will let us use the switch product IDs in the common source code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common initialization functions will be needed to enable
HW bridging support.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up the common code for setting up hardware bridging
and access to the forwarding database.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 has support for EEE. Check for the product ID and call
the common code if applicable.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable by using defines for the switch IDs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the switch id and save it away in the private mv88x6xxx structure
in a centralised piece of code, rather than each driver doing it itself.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for manipulating switch fdb entries by pointing to the
ndo_fdb functions implemented for mv88e6xxxx.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No vlan support at this time.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge support is similar for all chips supported by the mv88e6xxx code,
so add the code there.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will simplify adding offloaded bridge support later on.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prepares the driver for hardware bridging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split mv88e6xxx_reg_read and mv88e6xxx_reg_write into two functions each,
one to acquire smi_mutex and one to get struct mii_bus *bus from
struct dsa_switch *ds and to call the actual read/write function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datasheet says that the Message Port bit should not be set for the CPU port.
Having it set causes DSA tagged packets to be sent to the CPU port roughly
every 30 seconds. Those packets are the same as real packets forwarded between
switch ports if the switch is configured for switching between multiple ports.
The packets are then bridged by the software bridge, resulting in duplicated
packets on the network.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide mv88e6xxx_setup_port_common() for common port initialization.
Currently only write Port 1 Control and VLAN configuration since
this will be needed for hardware bridging. More can be added later
if desired/needed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code used and needed in mv886xxx.c should be initialized there as well,
so factor it out from the individual initialization files.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This would fix randconfig compile error:
net/built-in.o: In function `netdev_switch_fib_ipv4_abort':
(.text+0xf7811): undefined reference to `fib_flush_external'
Also it fixes following warnings:
warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET)
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE configuration is similar for the various MV88E6xxx chips.
Add generic support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading 64-bits register was not working because we inverted the steps
between reading the lower 32-bits of the register and reading the upper
32-bits. Swapping these operations is how the HW guarantees that 64-bits
reads are latched correctly. We only have a handful of 64-bits registers
for now, mostly MIB counters, so the imapct is low.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is configured to use single chip addressing mode, the
phy devices of the port are not accessible on the host MDIO
bus. Instead the switch internal MDIO bus must be used. For this to
work, the phy polling unit must be enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the power on/off recommended procedure for the Single GPHY we
have on our Starfighter 2 switch. In order to make sure we get proper
LED link/activity signaling during suspend, switch the link indication
from the Switch/MAC to the PHY.
Finally, since the GPHY needs to be reset to be put in low power mode,
we will loose any context applied to it: workarounds, EEE etc.. so we
need to call phy_init_hw() to get our fixups re-applied successfully.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code that touches the single GPHY register from
bcm_sf2_sw_resume() to a separate function since we will have to
enable/disable the GPHY from different locations, and we want the code
to be self-contained.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where there is only one switch, no routing table will have
been allocated, so do not dereference it in this case.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some busy bits are available in the global register 1, such as the ATU
Busy bit. We may want to use this function to wait for them to change,
so add a new parameter to mv88e6352_wait() instead of hard-coding
REG_GLOBAL2.
In the meantime, since the REG_READ() macro already checks for error,
remove the redundant check for ret < 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds debug messages for the generic mv88e6xxx read and write
routines. The output is similar to this:
mdio-gpio mdio-gpio.0: <- addr: 0x1b reg: 0x05 val: 0x4000
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x07 val: 0x3113
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x08 val: 0x0330
mdio-gpio mdio-gpio.0: -> addr: 0x1b reg: 0x09 val: 0x0000
This is convenient to dynamically debug operations through debugfs with:
echo file mv88e6xxx.c +p > <debugfs>/dynamic_debug/control
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the interrupt disabling in a function: bcm_sf2_intr_disable()
since we are doing the same thing in the setup and suspend paths.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do the following:
select FIXED_PHY if NET_DSA_BCM_SF2=y, as this implies that we will not be
able to build and/or run the driver correctly when built as a module,
which is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()").
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ports of the switch that we define as "fixed PHYs" such as MoCA, we
would have our Port 7 special handling that would allow us to assert the
link status indication.
For other ports, such as e.g: RGMII_1 connected to a cable modem, we
would rely on whatever the bootloader has left configured, which is a
bad assumption to make, we really need to force the link status
indication here.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
