Also, the us3_cpufreq driver can work on Ultra-IV and IV+.
They use the SAFARI bus register to control the clock divider
just like Ultra-III and III+ do.
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed ppc32 so that cur_cpu_spec is just a single pointer for all CPUs.
Additionally, made call_setup_cpu check to see if the cpu_setup pointer
is NULL or not before calling the function. This lets remove the dummy
cpu_setup calls that just return.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merged cputable.h between ppc32 and ppc64. In doing this removed support
for the BEGIN_FTR_SECTION/END_FTR_SECTION macros in C code since they
dont compile correctly. C code should use cpu_has_feature(). This is
based on Arnd Bergmann's initial patch.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge byteorder.h
Essentially adopts the 64-bit version of this file. The 32-bit version had
been using unsigned ints for arguments/return values that were actually
only 16 bits - the new file uses __u16 for these items as in the 64-bit
version of the header. The order of some of the asm constraints
in the 64-bit version was slightly different than the 32-bit version,
but they produce identical code.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following is generated when compiling a
recent (2.6.14-rc2-git5) kernel configured for
ARM, with GCC4.
CC init/main.o
In file included from include/linux/netdevice.h:29,
from include/net/sock.h:48,
from init/main.c:50:
include/linux/if_ether.h:114: error: array type has incomplete element type
It seems that if CONFIG_SYSCTL is not set, then
the compiler will throw an error due to the definition
of the ether_table[] array
Attached is a solution to the problem
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place them on separate cache lines in SMP to lower memory bouncing
between multiple CPU accessing the device.
- One part is mostly used on receive path (including
eth_type_trans()) (poll_list, poll, quota, weight, last_rx,
dev_addr, broadcast)
- One part is mostly used on queue transmit path (qdisc)
(queue_lock, qdisc, qdisc_sleeping, qdisc_list, tx_queue_len)
- One part is mostly used on xmit path (device)
(xmit_lock, xmit_lock_owner, priv, hard_start_xmit, trans_start)
'features' is placed outside of these hot points, in a location that
may be shared by all cpus (because mostly read)
name_hlist is moved close to name[IFNAMSIZ] to speedup __dev_get_by_name()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and rename it to pci.c. This also required moving
arch/ppc64/kernel/pci.h into include/asm-powerpc (called
ppc-pci.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Complete moving arch/ppc64/kernel/mpic.h,
include/asm-ppc/reg.h, include/asm-ppc64/kdebug.h
and include/asm-ppc64/kprobes.h
Add arch/powerpc/platforms/Makefile and use it from
arch/powerpc/Makefile
Introduce OLDARCH temporarily so we can point back to
the originating architecture
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
When you've enabled conntrack and NAT as a module (standard case in all
distributions), and you've also enabled the new conntrack netlink
interface, loading ip_conntrack_netlink.ko will auto-load iptable_nat.ko.
This causes a huge performance penalty, since for every packet you iterate
the nat code, even if you don't want it.
This patch splits iptable_nat.ko into the NAT core (ip_nat.ko) and the
iptables frontend (iptable_nat.ko). Threfore, ip_conntrack_netlink.ko will
only pull ip_nat.ko, but not the frontend. ip_nat.ko will "only" allocate
some resources, but not affect runtime performance.
This separation is also a nice step in anticipation of new packet filters
(nf-hipac, ipset, pkttables) being able to use the NAT core.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If input message rate from userspace is too high, do not drop them,
but try to deliver using work queue allocation.
Failing there is some kind of congestion control.
It also removes warn_on on this condition, which scares people.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro pointed out that the current IB userspace verbs interface
allows userspace to cause mischief by closing file descriptors before
we're ready, or issuing the same command twice at the same time. This
patch closes those races, and fixes other obvious problems such as a
module reference leak.
Some other interface bogosities will require an ABI change to fix
properly, so I'm deferring those fixes until 2.6.15.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Added a missing TO_NATIVE call to scripts/mod/file2alias.c:do_pcmcia_entry()
- Add an alignment attribute to struct pcmcia_device_no to solve an alignment
issue seen when cross-compiling on x86 for m68k.
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
At boot time, determine the D-cache, I-cache and E-cache size and
line-size. Use them in cache flushes when appropriate.
This change was motivated by discovering that the D-cache on
UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the
Cheetah error handlers were assuming a 32K size.
There are still some pieces of code that are hard coding things and
will need to be fixed up at some point.
While we're here, fix the D-cache and I-cache parity error handlers
to run with interrupts disabled, and when the trap occurs at trap
level > 1 log the event via a counter displayed in /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The trick is that we do the kernel linear mapping TLB miss starting
with an instruction sequence like this:
ba,pt %xcc, kvmap_load
xor %g2, %g4, %g5
succeeded by an instruction sequence which performs a full page table
walk starting at swapper_pg_dir.
We first take over the trap table from the firmware. Then, using this
constant PTE generation for the linear mapping area above, we build
the kernel page tables for the linear mapping.
After this is setup, we patch that branch above into a "nop", which
will cause TLB misses to fall through to the full page table walk.
With this, the page unmapping for CONFIG_DEBUG_PAGEALLOC is trivial.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Ben Dooks
The VA addresses of the Anubis CPLD registers
confoict with the addresses for the ISA space
maps used by the rest of the s3c2410 architecture
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
powerpc: Merge semaphore.h
Adopted the ppc64 version of semaphore.h. The 32-bit version used
smp_wmb(), but recent updates to atomic.h mean this is no longer required.
The 64-bit version made use of unlikely(), which has been retained in the
combined version.
This patch requires the recent atomic.h patch.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge asm-ppc*/rwsem.h into include/asm-powerpc.
Removed smp_*mb() memory barriers from the ppc32 code
as they are now burried in the atomic_*() functions as
suggested by Paul, implemented by Arnd, and pushed out
by Becky. I am not the droid you are looking for.
This patch depends on Becky's atomic.h merge patch.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge atomic.h and memory.h into powerpc
Merged atomic.h into include/powerpc. Moved asm-style HMT_ defines from
memory.h into ppc_asm.h, where there were already HMT_defines; moved c-style
HMT_ defines to processor.h. Renamed memory.h to synch.h to better reflect
its contents.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <linuxppc@jdl.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The spinlock_types.h merge renamed the structure for raw_spinlock_t to
match ppc64. In doing so some of the spinlock macros/functions needed to
be updated to match. Apparently, this seems to only be caught when
building power3.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a #define for SN_SAL_IOIF_PCI_SAFE and makes that the
preferred method of implementing sn_pci_legacy_read() and
sn_pci_legacy_write().
This SAL call has been present in SGI proms since version 4.10. If the
SN_SAL_IOIF_PCI_SAFE call fails, revert to the previous code for compatability
with older proms.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently rpc_mkdir/rpc_rmdir and rpc_mkpipe/mk_unlink have an API that's
a little unfortunate. They take a path relative to the rpc_pipefs root and
thus need to perform a full lookup. If you look at debugfs or usbfs they
always store the dentry for directories they created and thus can pass in
a dentry + single pathname component pair into their equivalents of the
above functions.
And in fact rpc_pipefs actually stores a dentry for all but one component so
this change not only simplifies the core rpc_pipe code but also the callers.
Unfortuntately this code path is only used by the NFS4 idmapper and
AUTH_GSSAPI for which I don't have a test enviroment. Could someone give
it a spin? It's the last bit needed before we can rework the
lookup_hash API
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In fact, ->set_buffer_size should be completely functionless for non-UDP.
Test-plan:
Check socket buffer size on UDP sockets over time.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Each transport implementation can now set unique bind, connect,
reestablishment, and idle timeout values. These are variables,
allowing the values to be modified dynamically. This permits
exponential backoff of any of these values, for instance.
As an example, we implement exponential backoff for the connection
reestablishment timeout.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Select an RPC client source port between 650 and 1023 instead of between
1 and 800. The old range conflicts with a number of network services.
Provide sysctls to allow admins to select a different port range.
Note that this doesn't affect user-level RPC library behavior, which
still uses 1 to 800.
Based on a suggestion by Olaf Kirch <okir@suse.de>.
Test-plan:
Repeated mount and unmount. Destructive testing. Idle timeouts.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
