Since get_settings() returns a signed int and it gets checked
for < 0 to catch an error, res should be a signed int too.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make phy 0 actually be read, as it is not being right now as we have:
int mii_status = mdio_read(dev, phy, MII_BMSR);
int phyx = phy & 0x1f;
When we should have instead:
int phyx = phy & 0x1f;
int mii_status = mdio_read(dev, phyx, MII_BMSR);
so that when phy, in the end of the (phy = 1; phy <= 32...) loop gets
to 32 phyx gets to 0, i.e. we were reading at 32, when the intended
read was for 0.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Unlike their older siblings, ICH6 and 7 use different scheme for MAP
VALUE. This patch makes ata_piix interpret MV properly on ICH6/7.
Pre-ICH6/7
The value of these bits indicate the address range the SATA port
responds to, and whether or not the SATA and IDE functions are
combined.
000 = Non-combined. P0 is primary master. P1 is secondary master.
001 = Non-combined. P0 is secondary master. P1 is primary master.
100 = Combined. P0 is primary master. P1 is primary slave. P-ATA is
2:0 Map Value secondary.
101 = Combined. P0 is primary slave. P1 is primary master. P-ATA is
secondary.
110 = Combined. P-ATA is primary. P0 is secondary master. P1 is
secondary slave.
111 = Combined. P-ATA is primary. P0 is secondary slave. P1 is
secondary master.
ICH6/7
Map Value - R/W. Map Value (MV): The value in the bits below indicate
the address range the SATA ports responds to, and whether or not the
PATA and SATA functions are combined. When in combined mode, the AHCI
memory space is not available and AHCI may not be used.
00 = Non-combined. P0 is primary master, P2 is the primary slave. P1
is secondary master, P3 is the 1:0 secondary slave (desktop
only). P0 is primary master, P2 is the primary slave (mobile
only).
01 = Combined. IDE is primary. P1 is secondary master, P3 is the
secondary slave. (desktop only)
10 = Combined. P0 is primary master. P2 is primary slave. IDE is secondary
11 = Reserved
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, without this patch, ata_piix misdetects my ICH7's combined mode,
ending up not applying bridge limits to PX-710SA and configuring IDE
drive on 40-c cable to UDMA/66.
Thanks.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In the case where a (broken) BIOS gives us a blank _CRS for
a PCI Interrupt Link Device, the acpi_walk_resources()
will not terminate, but will then give the callback
the resource end tag. Ignore the end tag.
Signed-off-by: Len Brown <len.brown@intel.com>
Handle system controller power down pending events
on SN systems. This allows the system to gracefully shutdown
before the system controller removes power due to
an adverse environmental condition.
Signed-off-by: Aaron Young <ayoung@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Actually I think this is more appropriate so we don't end up with 17
cases that add drivers/sn to the build lib.
Include drivers/sn when CONFIG_IA64_SGI_SN2 or CONFIG_IA64_GENERIC
is enabled.
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Convert to use a single mutex instead of two rwsems as this isn't
performance critical.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When the scsi_execute_async interface was added it ended up reducing
the flexibility of userspace to send arbitrary scsi commands through
sg using SG_IO. The SG_IO interface allows userspace to specify the
CDB length. This is now ignored in scsi_execute_async and it is
guessed using the COMMAND_SIZE macro, which is not always correct,
particularly for vendor specific commands. This patch adds a cmd_len
parameter to the scsi_execute_async interface to allow the caller
to specify the length of the CDB.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
BIOS might change frequency behind our back when BIOS changes allowed
frequencies via _PPC. In this case cpufreq core got out of sync.
Ask driver for current freq and notify governors about a change
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Patch from Lucas Correia Villa Real
This patch defines S3C2400 memory map and adds a S3C24XX macro for
common resources between S3C2400, S3C2410 and S3C2440 cpus.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some folk want to use RGB555 rather tahn RGB565 with amba-clcd.
Allow amba-clcd to accept either pixel format.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resetting the adapter causes the ServeRAID driver to exceed
the max time allowed by the softlock watchdog. Resetting the
hardware can easily require 30 or more seconds. To avoid the
"BUG: soft lockup detected on CPU#0!"
result, this patch replaces the mdelay() calls in the
initialization/reset routines with msleep().
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Internal lun discovery has been removed since fc_transport
integration. Short-circuiting for tape-devices in
qla2x00_update_fcport() could inadvertently result in a
blocked rport timing-out and its targets being reaped.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT]. Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue. If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport. The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch below "fixes" calculation of the virt_addr for the AUTO_REQSENSE
case. I put "fixes" in quotes because the real fix would be to completely
remove it, but that's beyond the scope of this patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New versions of the Power5 firmware can send a "re-enable" message to
the virtual scsi adapter. This fix makes us handle the message
correctly. Without it, the driver goes catatonic and the system crashes
unpleasantly.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
memset clears once set structure, there is actually no need for memset,
because configure function do it for us. Next, vfree(NULL) is legal, so
avoid useless labels.
Thanks Dave Jones for reporting this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
memset clears once set structure, there is actually no need for memset,
because configure function do it for us. Next, vfree(NULL) is legal, so
avoid useless labels.
Thanks Dave Jones for reporting this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes the following sparse warnings:
drivers/char/drm/via_dmablit.c:111:35: warning: Using plain integer as NULL pointer
drivers/char/drm/via_dmablit.c:584:23: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Fix CMDBUFFER path, add heap destroy and flesh out sarea for rotation
(Tungsten Graphics)
From: Alan Hourihane <alanh@tungstengraphics.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
From: Nick Piggin <npiggin@suse.de>
Allocate a compound page for the user mapping instead of tweaking the page
refcounts.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
From: Randy Dunlap <rdunlap@xenotime.net>
Use NULL instead of 0 (sparse warnings):
drivers/char/drm/ati_pcigart.c:64:10: warning: Using plain integer as NULL
pointer
drivers/char/drm/ati_pcigart.c:130:21: warning: Using plain integer as NULL
pointer
drivers/char/drm/ati_pcigart.c:171:14: warning: Using plain integer as NULL
pointer
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
From: Brice Goglin <Brice.Goglin@ens-lyon.org>
Now that Xorg 6.9/7.0 has been released, DRI is supported on more Radeon
cards without ATI proprietary drivers. I got my X300 to work without
problem. But, another Radeon X600 required to add its PCI ids to the
Radeon driver. Patch is attached.
I can't be sure about the "CHIP_RV350", I copied it from the X300 entry
(from http://dri.freedesktop.org/wiki/ATIRadeon, X600 is a rv380 chip while
X300 is a rv370). But, at least it works now.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
On my latest laptop, I've had occasional PHY dead on wakeup from
sleep... the PHY would be totally unresponsive even to toggling the hard
reset line until the machine is powered down... Looking closely at the
code, I found some possible issues in the way we setup the MDIO lines
during suspend along with slight divergences from what Darwin does when
resetting it that may explain the problem. That patch change these and
the problem appear to be gone for me at least... I also fixed an mdelay
-> msleep while I was at it to the pmac feature code that is called
when toggling the PHY reset line since sungem doesn't call it in an
atomic context anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>b
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 1.4.31 and add 2006 copyright.
Skip the last digit when reporting the firmware version.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance the ethtool loopback test with PHY loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround for a hardware interrupt issue. When using INTA,
unmasking of the interrupt and the tag update should be done
separately to avoid some spurious interrupts,
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix TCP/UDP checksum verification. Use status bits in the buffer
descriptor instead of the checksum value to verify rx checksum.
Using the checksum value will be incorrect if the UDP packet has
zero in the UDP checksum field.
Firmware update required for this fix.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some misc. fixes for WoL, 5708 B1, and a typo '=' instead of '=='.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve handshake with bootcode with the following changes:
1. Increase timeout to 100msec and use msleep instead of udelay.
2. Add more error checking for timeouts and errors.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always set up the device to strip incoming VLAN tags when ASF is
enabled. ASF firmware will not parse packets correctly if VLAN tags
are not stripped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix printk type warning:
drivers/media/dvb/b2c2/flexcop-pci.c:164: warning:
format '%08x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Move config byte from tuner_params to tuner_range struct.
- dvb tuners must be able to set different config byte for each range.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename cb variable names in tuner structures for global consistency
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fix printk type warning:
drivers/media/dvb/b2c2/flexcop-pci.c:164: warning:
format '%08x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- default_tuner_init was called twice due to a missing break statement.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
