Instead, allow using string formatting with send_monitor_note()
and access init_utsname().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the mgmt Start Limited Discovery command. Most
of existing Start Discovery code is reused since the only difference
is the presence of a 'limited' flag as part of the discovery state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the EIR parsing helper more general purpose, make it return
the found data and its length rather than just saying whether the data
was present or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use list_for_each_entry*() instead of list_for_each*() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
A Linux PC is connected with another device over Bluetooth PAN using a
BNEP interface.
Whenever a packet is tried to be sent over the BNEP interface, the
function "bnep_net_xmit()" in "net/bluetooth/bnep/netdev.c" is called.
This function calls "bnep_net_mc_filter()", which checks (if the
destination address is multicast) if the address is set in a certain
multicast filter (&s->mc_filter). If it is not, then it is not sent out.
This filter is only changed in two other functions, found in
net/bluetooth/bnep/core.c": in "bnep_ctrl_set_mc_filter()", which is
only called if a message of type "BNEP_FILTER_MULTI_ADDR_SET" is
received. Otherwise, it is set in "bnep_add_connection()", where it is
set to a default value which only adds the broadcast address to the
filter:
set_bit(bnep_mc_hash(dev->broadcast), (ulong *) &s->mc_filter);
To sum up, if the BNEP interface does not receive any message of type
"BNEP_FILTER_MULTI_ADDR_SET", it will not send out any messages with
multicast destination addresses except for broadcast.
However, in the BNEP specification (page 27 in
http://grouper.ieee.org/groups/802/15/Bluetooth/BNEP.pdf), it is said
that per default, all multicast addresses should not be filtered, i.e.
the BNEP interface should be able to send packets with any multicast
destination address.
It seems that the default case is wrong: the multicast filter should not
block almost all multicast addresses, but should not filter out any.
This leads to the problem that e.g. Neighbor Solicitation messages sent
with Bluetooth PAN over the BNEP interface to a multicast destination
address other than broadcast are blocked and not sent out.
Therefore, in the default case, we set the mc_filter to ~0LL to not
filter out any multicast addresses.
Signed-off-by: Danny Schweizer <danny.schweizer@proofnet.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces register and unregister functionality for lowpan
interfaces. While register a lowpan interface there are several things
which need to be initialize by the 6lowpan subsystem. Upcoming
functionality need to register/unregister per interface components e.g.
debugfs entry.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're doing background scanning and connection attempts it's
possible we timeout trying to connect and go back to scanning again.
The timeout triggers a HCI_LE_Create_Connection_Cancel which will
trigger a Connection Complete with "Unknown Connection Identifier"
error status. Since we go back to scanning this isn't really a failure
and shouldn't be presented as such to user space through mgmt.
The exception to this is if the connection attempt was due to an
explicit request on an L2CAP socket (indicated by
params->explicit_connect being true). Since the socket will get an
error it's consistent to also notify the failure on mgmt in this case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All LE connections are now triggered through a preceding passive scan
and waiting for a connectable advertising report. This means we've got
the best possible guarantee that the device is within range and should
be able to request the controller to perform continuous scanning. This
way we minimize the risk that we miss out on any advertising packets.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.3+
We can simplify a lot of code by making sure hdev->cur_adv_instance is
always up-to-date. This allows e.g. the removal of the
get_current_adv_instance() helper function and the special
HCI_ADV_CURRENT value. This patch also makes selecting instance 0x00
explicit in the various calls where advertising instances aren't
enabled, e.g. when HCI_ADVERTISING is set or we've just finished
enabling LE.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The logic in powered_update_hci() to initialize the advertising data &
state is a bit more complicated than it needs to be. It was previously
not doing anything if HCI_LE_ENABLED wasn't set, but this was not
obvious by quickly looking at the code. Now the conditions for the
various actions are more explicit. Another simplification is due to
the fact that __hci_req_schedule_adv_instance() takes care of setting
hdev->cur_adv_instance so there's no need to set it before calling the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_run() function already checks for empty cmd_q and bails
out if necessary. Also, req.cmd_q should really be treated as private
data of the request and not accessed directly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The __hci_req_update_scan_rsp_data gets the instance to be updated
which should get passed to update_inst_scan_rsp_data() instead of
always enabling the current instance.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag just tells us whether hdev->adv_instances is empty or not.
We can equally well use the list_empty() function to get this
information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The code in the Read Advertising Features mgmt command handler is
unnecessarily complicated. Clean it up and remove unnecessary
variables & branches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.
Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.
Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need this both in hci_request.c and mgmt.c so move it to
hci_request.c as a generic helper.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need to update the EIR both from hci_request.c and mgmt.c
so move update_eir() as a more generic request helper to
hci_request.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need this both from hci_request.c and mgmt.c so move it as
a request helper function to hci_request.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The discoverable mode is intrinsically linked with the connectable
mode e.g. through sharing the same HCI command (Write Scan Enable) for
BR/EDR. It makes therefore sense to move it to hci_request.c and run
the changes through the same hdev->req_workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Class of Device needs to be changed e.g. for limited discoverable
mode. In preparation of moving the discoverable mode to hci_request.c
and hdev->req_workqueue, move the Class of Device helpers there first.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This way the connectable changes are synchronized against each other,
which helps avoid potential races. The connectable mode is also linked
together with LE advertising which makes is more convenient to have it
behind the same workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This way we avoid the need to do a forward declaration in later
patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since Add/Remove Device perform the page scan updates independently
from the HCI command completion we've introduced a potential race when
multiple mgmt commands are queued. Doing the page scan updates through
the req_workqueue ensures that the state changes are performed in a
race-free manner.
At the same time, to make the request helper more widely usable,
extend it to also cover Inquiry Scan changes since those are behind
the same HCI command. This is also reflected in the new name of the
API as well as the work struct name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2015-12-01
Here's a Bluetooth fix for the 4.4-rc series that fixes a memory leak of
the Security Manager L2CAP channel that'll happen for every LE
connection.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a cleanup to make following patch easier to
review.
Goal is to move SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
from (struct socket)->flags to a (struct socket_wq)->flags
to benefit from RCU protection in sock_wake_async()
To ease backports, we rename both constants.
Two new helpers, sk_set_bit(int nr, struct sock *sk)
and sk_clear_bit(int net, struct sock *sk) are added so that
following patch can change their implementation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increments the management interface revision due to
introduction of a new Get Advertising Size Information command and
various other fixes & improvements.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to enable advertising with privacy enabled, SMP has to be
registered in order to generate new RPA. During power on, it will be
registered at the very end which is the reason why advertising is not
enabled and it's not possible to enable it anymore due to mismatch
between hci_dev settings and actual controller state.
This fixes this problem by moving SMP registration earlier, just after
controller is powered (which is ok, because LE SMP will be already able
to decide on identity address to be used), but before advertising is
enabled.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There were a couple of code paths missed by the previous patch that
added a HCI status return parameter to __hci_req_sync. This patch adds
the missing assignments for them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Get Advertising Size Information command allows to retrieve size
information for advertising data and scan response data fields depending
on the selected flags. This is useful if applications want to know the
available size ahead of time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The if statements for checking the flags parameter could be written a
bit easier to read. This changes this. No functional behavior has been
changed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The instance range check for Add Advertising command is missing. If the
provided instance is out of range an Invalid Parameters error should be
returned. At the moment, the generic Failed error is returned. This
extra check ensures that clear error messages are returned.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove unneeded variable used to store return value.
Error reported by coccicheck.
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix errors reported by checkpatch.
- ERROR: spaces required around that ':' (ctx:VxW)
- ERROR: open brace '{' following function declarations go on the next line
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The kfree_skb() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_sync_cancel() is just as much related to the request
cleanup as hci_request_cancel_all() is. Just move the former into the
latter and do the cleanup from a single place in hci_dev_do_close().
The important thing is to avoid deadlocks by holding the req_sync
lock: previously hci_request_cancel_all was done right after releasing
the lock and with this patch it's right before taking it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The conn_unfinished variable makes the entire logic of
hci_connect_le() rather confusing. By restructuring and clarifying the
logic we can actually remove the conn_unfinished variable and still
keep the same behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This helps simplify the logic in further patches (less cleanups to do
in this failure branch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_connect_le_scan() is (as the name implies) a master/central
role API, so it makes no sense in passing a role parameter to it. At
the same time this patch also fixes the direct advertising support for
LE L2CAP sockets where we now call the more appropriate hci_le_connect()
API if slave/peripheral role is desired.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The only user of this, le_scan_restart_work(), is so short and simple
that it makes sense to just merge the code there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Merge le_scan_disable_work_complete into the main le_scan_disable_work
function and take advantage of the updated bredr_inquiry() to run the
Inquiry through hci_req_sync().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Passing the needed inquiry length to bredr_inquiry() makes it possible
to also use this helper for interleaved discovery where the controller
doesn't support simultaneous Inquiry & LE scan.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The recent changes to remove dependency on HCI in Add Device missed
out relevant changes for BR/EDR. This patch removes the left-overs and
ensures the right HCI command gets queued for BR/EDR.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since discovery also deals with LE scanning it makes sense to move it
behind the same req_workqueue as other LE scanning changes. This also
simplifies the logic since we do many of the actions in a synchronous
manner.
Part of this refactoring is moving hci_req_stop_discovery() to
hci_request.c. At the same time the function receives support for
properly handling the STOPPING state since that's the state we'll be
in when stopping through the req_workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
