Via of_get_named_gpio(), wp_gpio can become -EPROBE_DEFER which now makes
probe() return -EPROBE_DEFER as well to wait until the gpio controller is
probed before trying to probe lpc32xx_slc again.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes the lpc32xx_slc driver use of_get_named_gpio() instead of
of_get_named_gpio_flags() whose flags are discarded anyway.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The Programmable Multibit ECC (PMECC) controller is a programmable binary
BCH(Bose, Chaudhuri and Hocquenghem) encoder and decoder. This controller
can be used to support both SLC and MLC NAND Flash devices. It supports to
generate ECC to correct 2, 4, 8, 12 or 24 bits of error per sector of data.
To use PMECC in this driver, the user needs to set the address and size of
PMECC, PMECC error location controllers and ROM. And also needs to pass the
correction capability, the sector size and ROM lookup table offsets via dt.
This driver has been tested on AT91SAM9X5-EK and AT91SAM9N12-EK with JFFS2,
YAFFS2, UBIFS and mtd-utils.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The SBC8260 support was dropped back when we moved from ppc to
powerpc. We are now also dropping the support for the EOL SBC8560,
so we can also delete this mapping support, as they were the only
users of it.
Artem: also remove the symbol from the Makefile.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function only returns 0 or -1, so make that clear.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
These descriptors are for BBT's that don't use OOB; the "no_bbt" name doesn't
really make sense.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The commit bf4289cba0 removed the use of
CONFIG_MTD_NAND_ATMEL_ECC_NONE and CONFIG_MTD_NAND_ATMEL_ECC_HW but the
Kconfig file was forgotten.
This patch remove those inoperative options.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This manufacturer ID is used under the name Spansion.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The Kconfig help on "Flash cmd/query data swapping" still mentions
LART_ENDIAN_BYTE. That option used to be relevant for setting
CONFIG_MTD_CFI_LART_BIT_SWAP. That option and macro got both removed in
v2.4.11-pre4. So, although LART endianness sounds intriguing, that part
of the help text can be removed.
And, while we're touching this choice, move the help text up one level.
Currently it's available under the "NO" option, while it's relevant for
all three options.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the SLC NAND controller inside the LPC32xx SoC.
[dwmw2: 21st century pedantry]
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.
Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
1. add return 'int' value for 'write_page' function.
2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
3. add code to test the return value, and if negative, indicate an
error happend when write page with ECC.
4. fix the compile warning in all impacted nand flash driver.
Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The code responsible for reading the version of the mirror bbt was
incorrectly using the descriptor of the main bbt.
Pass the mirror bbt descriptor to 'scan_read_raw' when reading the
version of the mirror bbt.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org [v2.6.37+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The only relevant change between i.MX51 and i.MX53 is that
a bitfield is shifted one bit to the left.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The i.MX v3 nand controller (i.MX5) needs two memory resources.
Traditionally we have the AXI resource first. For sorting in this
driver into the devicetree it feels much more natural to have the
IP resource first. This patch swaps the ordering of these two
resources.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
To make the error path simpler and to make subsequent patches
easier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Previously the remove method was looping and removing all chips,
which is obviously not the right thing to do — left over from when
the driver was organized differently and that was the remove method for
the entire controller. This would result in bad things happening if
you have more than one NAND chip, and remove the module.
This also fixes priv->dev to properly point to the chip's device rather than
the controller's. Until now priv->dev was only used for error/debug prints
(and it's an improvement there), so this shouldn't break anything.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adds JEDEC ID for the 1.8V version of WinBond w25q32.
Signed-off-by: Federico Fuga <fuga@studiofuga.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Prepare the clock before enabling it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a clean-up patch which removes the own pseudo-random numbers generator
from the speed- and stress-tests and makes them use the 'random32()' generator
instead.
[dwmw2: Merge later fix for negative offsets]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In hardware ecc mode, the flctl now writes and reads the oob data
provided by the user. Additionally the ECC is now returned in normal
page reads, not only when using the explicit NAND_CMD_READOOB command.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are multiple reasons for a rewrite:
- a race exists: when _4ECCEND is set, _4ECCFA may become true too
meanwhile, which is lost and a non-correctable error is treated as
correctable.
- the ECC statistics don't get properly propagated to the base code.
- empty pages would get marked as corrupted
The rewrite resolves the issues and I hope it gives a more explicit
code flow structure.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When we use hardware ecc, the flctl is run in so-called "sector access
mode". We can bundle 4 sector accesses when using 2KiB page sizes to read
a whole page at once and speed up things.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As the equation mtd->writesize == eccsteps * eccsize holds, we can
simplify the code. The second loop of the 1st hunk is never entered,
so we delete it.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The flctl uses 10 bytes ECC data for every 512 bytes sector. This patch
makes the controller write all 40 bytes instead of 10 bytes only.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The flctl hardware has changed and a new OOB layout must be adapted for
2KiB page size NAND chips when using hardware ECC.
The related bit fields ECCPOS[0-2] are gone — the bits are marked as
reserved now in the datasheet. As there are no official users of the
hardware ECC so far, they are completely removed.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When the data transfer between the controller and the NAND chip fails,
we now get notified.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the unmapping for the error case and for the driver removal.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is simply an added warning in the comments. Ideally, this patch
need not be merged, but rather, a developer will write a proper solution
that can use the ecc.read_oob_raw and ecc.write_oob_raw interfaces.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We can clean up the loop logic a bit, here. This refactoring was enabled
in part by:
Commit bb4a09866 [mtdoops: clean-up new MTD API usage]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd_read_oob() will be expanded a little, so don't leave it in the header
as a static inline function.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We don't need to open code the divide function, just use div_u64 that
already exists and do the same job. While this is a straightforward
clean up, there is more to that, the real motivation for this.
While building on a cross compiling environment in armel, using gcc
4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5), I was getting the following build
error:
ERROR: "__aeabi_uldivmod" [drivers/mtd/nand/nandsim.ko] undefined!
After investigating with objdump and hand built assembly version
generated with the compiler, I narrowed __aeabi_uldivmod as being
generated from the divide function. When nandsim.c is built with
-fno-inline-functions-called-once, that happens when
CONFIG_DEBUG_SECTION_MISMATCH is enabled, the do_div optimization in
arch/arm/include/asm/div64.h doesn't work as expected with the open
coded divide function: even if the do_div we are using doesn't have a
constant divisor, the compiler still includes the else parts of the
optimized do_div macro, and translates the divisions there to use
__aeabi_uldivmod, instead of only calling __do_div_asm -> __do_div64 and
optimizing/removing everything else out.
So to reproduce, gcc 4.6 plus CONFIG_DEBUG_SECTION_MISMATCH=y and
CONFIG_MTD_NAND_NANDSIM=m should do it, building on armel.
After this change, the compiler does the intended thing even with
-fno-inline-functions-called-once, and optimizes out as expected the
constant handling in the optimized do_div on arm. As this also avoids a
build issue, I'm marking for Stable, as I think is applicable for this
case.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: stable@vger.kernel.org
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The gpmi-nand driver uses virt_addr_valid() to check whether a buffer
is suitable for dma. If it's not, a driver allocated buffer is used
instead. Then after a page read the driver allocated buffer must be
copied to the user supplied buffer. This does not happen since commit
7725cc8593.
This patch fixes the issue. The bug is encountered with UBI which uses a
vmalloced buffer for the volume table.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: snijsure@grid-net.com
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The following commit changes the function used to copy from/to
the hardware buffer to memcpy_[from|to]io. This does not work
since the hardware cannot handle the byte accesses used by these
functions. Instead of reverting this patch introduce 32bit
correspondents of these functions.
| commit 5775ba36ea9c760c2d7e697dac04f2f7fc95aa62
| Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
| Date: Tue Apr 24 10:05:22 2012 +0200
|
| mtd: mxc_nand: fix several sparse warnings about incorrect address space
|
| Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
| Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The intent here was clearly to set result to true if the 0x40000000 flag
was set. But instead there was a | vs & typo and we always set result
to true.
Artem: check the spec at
wiki.laptop.org/images/5/5c/88ALP01_Datasheet_July_2007.pdf
and this fix looks correct.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As of edbc454 [mtd: driver _read() returns max_bitflips; mtd_read()
returns -EUCLEAN], 'mtd->bitflip_threshold' must be set for mtd devices
having ECC, prior any 'mtd_read()' call.
Otherwise, 'mtd_read()' will falsely return -EUCLEAN.
Normally, 'mtd->bitflip_threshold' is initialized when the MTD is added.
However, this is too late for NAND MTDs, as 'scan_bbt()' is invoked
prior the existing initialization of 'mtd->bitflip_threshold'.
This is a problem since 'scan_bbt()' calls 'mtd_read()', in the case
of a flash-based bad block table.
It resulted in a falsely reported bitflips indication during BBT read,
which lead to constant scrubbing of the flash BBT blocks.
Initialize 'mtd->bitflip_threshold' to its default value (if not already
set by the driver), prior to invocation of 'scan_bbt()'.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit "62f38455 UBI: modify ubi_wl_flush function to clear work queue for a lnum"
takes the 'work_sem' semaphore in write mode for the entire loop, which is not
very good because it will block other workers for potentially long time. We do
not need to have it in write mode - read mode is enough, and we do not need to
hole it over the entire loop. So this patch turns changes the locking: takes
'work_sem' in read mode and pushes it down to the loop.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Commit "aa44d1d UBI: remove Kconfig debugging option" broke UBI and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Since commit 6a918bade9, the mxc_nand driver
fails with:
Driver must set ecc.strength when using hardware ECC
This is because nand_scan_tail checks for correct ecc strength
settings, so we must set them up before nand_scan_tail.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org [3.4+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.
This is caused by 1dbebd3256
(mtd: harmonize mtd_writev usage).
Remove the assignment from the block2mtd driver to fix the
issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
