This function just calls into genphy_restart_aneg() to perform an
autonegotation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is useful to know which MDIO driver is being registered, demote
the pr_info() to a pr_debug().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of remembering if the page was changed, just compare the current
page to the saved one. This is easier and has the advantage to save a
register write if the page was already restored.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_aneg_done() available to drivers so that the result of the
auto-negotiation initiated by phy_start_aneg() can be determined.
Remove the local implementation of phy_aneg_done() from the Aeroflex
driver and use the phy library version.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dp83640 has a frequency resolution of about 0.029 ppb.
This patch lets users of the device benefit from the
increased frequency resolution when tuning the clock.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
This PHY seems to only implement some standard registers and need some
workarounds to provide autoneg values from vendor registers.
Some magic values are currently used to configure the PHY, and this a
temporary setup until clarification about these registers names and
registers fields are provided by Amlogic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().
Note that both function still take a reference to the phy device
through phy_attach_direct().
Fixes: e13934563d ("[PATCH] PHY Layer fixup")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.
Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to read the AUXCTL register for the BCM54xx. This
mirrors the bcm54xx_auxctl_write function already present in the code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a definition for PHY ID mask for improving code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SGMII mode, we observed an autonegotiation issue
after power-down-up cycles where the copper side
reports successful link establishment but the
SGMII side's link is down.
This happened in a setup where the at8031 is
connected over SGMII to a eTSEC (fsl gianfar),
but so far could not be reproduced with other
Ethernet device / driver combinations.
This commit adds a wrapper function for at8031
that in case of operating in SGMII mode double
checks SGMII link state when generic aneg_done()
succeeds. It prints a warning on failure but
intentionally does not try to recover from this
state. As a result, if you ever see a warning
'803x_aneg_done: SGMII link is not ok' you will
end up having an Ethernet link up but won't get
any data through. This should not happen, if it
does, please contact the module maintainer.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 98267311fe.
Suspending the SGMII alongside the copper side
made the at803x inaccessable while powered down,
e.g. it can't be re-probed after suspend.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This PHY has internal delays enabled after reset. This clears the
internal delay enables unless the interface specifically requests them.
Signed-off-by: Xo Wang <xow@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AQR106 and AQR107 can use the existing driver.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.
This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.
For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_supported_speeds provides a means to get a list of all the speeds a
phy device currently supports.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During phy state machine state transitions some set of actions should
occur whenever the link state changes. These actions should be
encapsulated into a single function
This patch adds the phy_adjust_link function, which is called whenever
phydev->adjust_link would have been called before. Actions that should
occur whenever the phy link is adjusted can now be added to the
phy_adjust_link function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for programmable MAC impedance configuration
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the fixed name "phy_interrupt" is not very informative in
/proc/interrupts when there are a lot of phys, e.g. a device with an
Ethernet switch. So when requesting the interrupt, use the name of the
phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt lines from PHYs maybe connected to I2C bus expanders, or
from switches on MDIO busses. Such interrupts are sourced from devices
which sleep, so use threaded interrupts. Threaded interrupts require
that the interrupt requester also uses the threaded API. Change the
phylib to use the threaded API, which is backwards compatible with
none-threaded IRQs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
being specified as positive values instead of negative (both
documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
"vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_start() is used to indicate the PHY is now ready to do its
work. The state is changed, normally to PHY_UP which means that both
the MAC and the PHY are ready.
If the phy driver is using polling, when the next poll happens, the
state machine notices the PHY is now in PHY_UP, and kicks off
auto-negotiation, if needed.
If however, the PHY is using interrupts, there is no polling. The phy
is stuck in PHY_UP until the next interrupt comes along. And there is
no reason for the PHY to interrupt.
Have phy_start() schedule the state machine to run, which both speeds
up the polling use case, and makes the interrupt use case actually
work.
This problems exists whenever there is a state change which will not
cause an interrupt. Trigger the state machine in these cases,
e.g. phy_error().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kyle Roeschley <kyle.roeschley@ni.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An extra entry for MDIO_XGENE got added during merging.
Delete it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-LAN (WoL) is an Ethernet networking standard that allows
a computer/device to be turned on or awakened by a network message.
VSC8531 PHY can support this feature configure by driver set function.
WoL status get by driver get function.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set bit 0 in register 1C.23 to enable the EDPD feature of the
KSZ9031 PHY. This reduces power consumption when the link is
down.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Edge-rate:
As system and networking speeds increase, a signal's output transition,
also know as the edge rate or slew rate (V/ns), takes on greater importance
because high-speed signals come with a price. That price is an assortment of
interference problems like ringing on the line, signal overshoot and
undershoot, extended signal settling times, crosstalk noise, transmission
line reflections, false signal detection by the receiving device and
electromagnetic interference (EMI) -- all of which can negate the potential
gains designers are seeking when they try to increase system speeds through
the use of higher performance logic devices. The fact is, faster signaling
edge rates can cause a higher level of electrical noise or other type of
interference that can actually lead to slower line speeds and lower maximum
system frequencies. This parameter allow the board designers to change the
driving strange, and thereby change the EMI behavioral.
Edge-rate parameters (vddmac, edge-slowdown) get from Device Tree.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the review comments updated and resending for review.
This is MAC interface feature.
Microsemi PHY can support RGMII, RMII or GMII/MII interface between MAC and PHY.
MAC-IF function program the right value based on Device tree configuration.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/phy/microchip.c:58:5: warning: no previous prototype for 'lan88xx_suspend' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'IS_ERR(pdata->clk)' is true, then 'clk_disable_unprepare(pdata->clk)'
will do nothing.
It is likely that 'if (!IS_ERR(pdata->clk))' was expected here.
In fact, the test can even be removed because 'clk_disable_unprepare'
already handles such cases.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-xgene driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing VSC85xx PHY driver did not follow the coding style and caused "checkpatch" to complain. This commit fixes this.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
commit 33c133cc75 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/phy/xilinx_gmii2rgmii.c:61:5: warning:
symbol 'xgmiitorgmii_probe' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the ksz8081, the ksz9031 has the behavior where it will clear the
interrupt enable bits when leaving power down. This takes advantage of the
solution provided by f5aba91.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This node pointer is returned by of_parse_phandle() with
refcount incremented in this function. of_node_put() on it
before exitting this function.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the redundant "Support for" and "Drivers for" from the Kconfig
short description. This makes the manufacture much more prominent in
the list and makes the shortcut keys useful.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort the files to reduce merge conflicts and to make it easier to find
drivers by name. Also separate the MDIO bus drivers from the PHY
drivers, again to help find what you need.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implementing this driver most of the inputs is
provided by Andrew Lunn.
Updating the driver with Andrew Copy right.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where phydev->interrupts is not PHY_INTERRUPT_ENABLED
function vsc85xx_ack_interrupt is returning an uninitialized
garbage value. Fix this by initializing rc to zero.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
