Commit Graph

998 Commits

Author SHA1 Message Date
Nobuhiro Iwamatsu
7a516280b6 sh: Fix compile error by operands(mov.l) in sh3/entry.S
-- log --
arch/sh/kernel/cpu/sh4/../sh3/entry.S:365: Error: invalid operands for opcode
make[4]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
make[3]: *** [arch/sh/kernel/cpu/sh4] Error 2
-- log --

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-16 19:49:21 +09:00
Kuninori Morimoto
4c3f450ba4 sh: Add OHCI USB support for SH7786
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-16 19:40:34 +09:00
Ingo Molnar
edb35028e4 Merge branches 'irq/genirq' and 'linus' into irq/core 2009-03-16 09:20:13 +01:00
Francesco VIRLINZI
4a55026fd7 sh: clkfwk: Add resume from hibernation support.
This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.

Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-11 17:18:50 +09:00
Francesco VIRLINZI
d680c76ecc sh: clkfwk: add clk_set_parent/clk_get_parent
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.

Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-11 17:18:46 +09:00
Yoshihiro Shimoda
2f47f44790 sh: Support fixed 32-bit PMB mappings from bootloader.
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.

P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-10 15:49:54 +09:00
Magnus Damm
2ef7f0dab6 sh: hibernation support
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.

To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.

The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.

Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-10 12:55:40 +09:00
Paul Mundt
edab56f4c9 sh: multiple vectors per irq - sh7720.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 19:21:02 +09:00
Paul Mundt
56d604defa sh: multiple vectors per irq - sh7710.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 19:20:48 +09:00
Paul Mundt
0caedb02c4 sh: multiple vectors per irq - sh7705.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 19:20:32 +09:00
Paul Mundt
592acbda89 sh: multiple vectors per irq - sh770x.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 19:20:14 +09:00
Paul Mundt
053bfc5360 sh: multiple vectors per irq - mxg.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 19:19:54 +09:00
Paul Mundt
5dece2bbda sh: multiple vectors per irq - sh7619.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 19:19:31 +09:00
Paul Mundt
f858abbecd sh: multiple vectors per irq - sh7206.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 18:34:15 +09:00
Paul Mundt
d55eedd57d sh: multiple vectors per irq - sh7201.
Follow the conversions as per the other subtypes.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 18:21:38 +09:00
Paul Mundt
e45efe68d1 sh: multiple vectors per irq - sh7263.
Convert over the SH7263 IRQ groups as well.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 18:02:33 +09:00
Paul Mundt
bb943a286c sh: multiple vectors per irq - sh7203.
Follow the conversions as per the other subtypes.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 17:58:51 +09:00
Nobuhiro Iwamatsu
075901af28 sh: Restore RTC IRQ setting for SH7763 setup.
This was accidentally dropped in the multiple vectors per irq conversion.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 14:37:34 +09:00
Nobuhiro Iwamatsu
a6bc77241d sh: multiple vectors per irq - sh7763
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.

This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-06 14:18:43 +09:00
Kuninori Morimoto
55ba99eb21 sh: Add support for SH7786 CPU subtype.
This adds preliminary support for the SH7786 CPU subtype.

While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.

More information on this particular CPU subtype is available at:

	http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-03 15:40:25 +09:00
Paul Mundt
0d5e19ab07 sh: Fix up SH-X3 general exception handler build.
With the recent entry.S refactoring, the SH-X3 path had a mov.l for a
register to register copy, resulting in:

  AS      arch/sh/kernel/cpu/sh4/../sh3/entry.o
arch/sh/kernel/cpu/sh4/../sh3/entry.S: Assembler messages:
arch/sh/kernel/cpu/sh4/../sh3/entry.S:366: Error: invalid operands for opcode
make[3]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1

Switch it over to a mov to fix it up.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 17:02:28 +09:00
Magnus Damm
57e41c86e2 sh: multiple vectors per irq - sh7785
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.

This fixes potential irq masking issues for sh7785 hardware
blocks such as SCIF/DMAC/PCIC5/MMCIF/GDTA/FLCTL/GPIO

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:53:50 +09:00
Magnus Damm
a842fb2d11 sh: multiple vectors per irq - sh7780
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.

This fixes potential irq masking issues for sh7780 hardware
blocks such as SCIF/RTC/DMAC/PCIC5/MMCIF/FLCTL/GPIO

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:53:50 +09:00
Magnus Damm
69977e7e25 sh: multiple vectors per irq - sh7750
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.

This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:53:50 +09:00
Magnus Damm
bdaa6e8062 sh: multiple vectors per irq - base
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:

 - If multiple vectors share the same enum then only the
   first vector will be available as a linux irq.

 - Drivers may need to be rewritten to get pending irq
   source from the hardware block instead of irq number.

This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.

Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:53:50 +09:00
Magnus Damm
0197f21ca5 sh: prefetch early exception data on sh4/sh4a.
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:41:17 +09:00
Magnus Damm
4f099ebb27 sh: remove EXPEVT vector from stack on sh3/sh4/sh4a
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:26:19 +09:00
Magnus Damm
1dd22722f6 sh: rework register restore code for sh3/sh4/sh4a
This patch reworks the sh3/sh4/sh4a register restore code in
the following ways:
 - break out restore_regs() from restore_all()
 - the register saving order is unchanged
 - use restore_regs() in sh_bios_handler and restore_all
 - document the function

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:26:14 +09:00
Magnus Damm
1d015cf02a sh: shared register saving code for sh3/sh4/sh4a
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
 - break out prepare_stack_save_dsp() from handle_exception()
 - break out save_regs() from handle_exception()
 - the register saving order is unchanged
 - align new functions to fit in cache lines
 - separate exception code from interrupt code
 - keep main code flow in a single cache line per exception vector
 - use bsr/rts for regular functions (save pr first)
 - keep data in one shared cache line (exception_data)
 - document the functions
 - tie in the hp6xx code

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-27 16:26:10 +09:00
Ingo Molnar
8f8573ae9f Merge branches 'irq/genirq', 'irq/sparseirq' and 'irq/urgent' into irq/core 2009-02-13 11:57:18 +01:00
Paul Mundt
41480ae7a3 Merge branch 'sh/stable-updates' 2009-02-12 17:27:56 +09:00
Tobias Klauser
270c5609e2 sh: Storage class should be before const qualifier
The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-02-12 17:26:09 +09:00
Paul Mundt
c161e40f45 sh: Don't enable GENERIC_TIME for the CMT clockevent driver yet.
GENERIC_TIME still depends on the clocksource bits being there, which is
presently not supported. This allows the CMT clockevent driver to be used
alongside alternate system timers that do not yet provide a clocksource
of their own (MTU2 and so on in the case of SH-2A).

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 18:11:25 +09:00
Paul Mundt
d63f3a5857 sh: Fix up MTU2 support for SH7203.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 18:10:13 +09:00
Magnus Damm
424f59d04d sh: CMT platform data for sh7723/sh7722/sh7366/sh7343
CMT platform data for SuperH Mobile sh7723/sh7722/sh7343/sh7366.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 17:02:51 +09:00
Magnus Damm
07821d3310 sh: fix no sys_timer case
Handle the case with a sys_timer set to NULL.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 16:45:47 +09:00
Magnus Damm
70f0800133 sh: tmu disable support
Add TMU disable support so we can use other clockevents.
Also, setup the clockevent rating.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 16:44:18 +09:00
Magnus Damm
955c077872 sh: rework clocksource and sched_clock
Rework and simplify the sched_clock and clocksource code. Instead
of registering the clocksource in a shared file we move it into the
tmu driver. Also, add code to handle sched_clock in the case of no
clocksource.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 16:44:17 +09:00
Paul Mundt
e4e3c3f17f Merge branch 'sh/stable-updates' 2009-01-29 11:56:45 +09:00
Paul Mundt
03f07876df sh: Fix up spurious syscall restarting.
The T-bit manipulation for syscall error checking had the side effect of
spuriously returning ERESTART* errno values over EINTR. So, we simplify
the error checking a bit and leave the T-bit alone.

Reported-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 11:56:03 +09:00
Carmelo AMOROSO
0f6dee232f sh: fcnvds fix with denormalized numbers on SH-4 FPU.
This fixes a bug in the FPU exception handler for the FCNVDS instruction.
To get the register number the instruction is shifted right by 9,
though it should be shifted right by 8.

More information at ST Linux bugzilla:

	https://bugzilla.stlinux.com/show_bug.cgi?id=4892

Signed-off-by: Giuseppe Di Giore <giuseppe.di-giore@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 11:56:02 +09:00
Christopher SMITH
4886516310 sh: Only reserve memory under CONFIG_ZERO_PAGE_OFFSET when it != 0.
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-29 11:56:02 +09:00
Paul Mundt
57e97cb8be sh: Fix up GENERIC_GPIO build for ARCH_WANT_OPTIONAL_GPIO cases.
CPUs define pinmux tables through the optional interface, while boards
that require demux of their own require it explicitly. Roll the Makefile
rules back to depend on GENERIC_GPIO, which covers both cases.

Fixes a link error with an undefined reference to register_pinmux() on
optional platforms.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-27 14:49:10 +09:00
Magnus Damm
69edbba002 sh: use gpiolib
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-27 14:49:10 +09:00
Magnus Damm
3292094e88 sh: lockless gpio_set_value()
This patch optimizes the gpio data register handling for gpio_set_value().

Instead of using the good old spinlock-plus-read-modify-write strategy
we now use a shadow register and atomic operations.

This improves the bitbanging mmc performance on Migo-R from 26 Kbytes/s
to 40 Kbytes/s.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-27 14:49:10 +09:00
Magnus Damm
0fc64cc0a2 sh: lockless gpio_get_value()
This patch separates the register read and write functions to
allow lockless gpio_get_value().

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-27 14:49:09 +09:00
Magnus Damm
18801be7f8 sh: make gpio_get/set_value() O(1)
This patch modifies the table based SuperH gpio implementation to
make use of direct table lookups. With this change the functions
gpio_get_value() and gpio_set_value() are O(1).

Tested on Migo-R using bitbanging mmc. Performance is improved from
11 KBytes/s to 26 Kbytes/s.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-27 14:49:09 +09:00
SUGIOKA Toshinobu
2afb447f33 sh: fix unaligned and nonexistent address handling
unaligned and nonexistent address causes wrong exception
handling in traps_32.c(handle_unaligned_access).

'handle_unalinged_ins' should return -EFAULT if address error
is fixed up with kernel exception table, otherwise
'handle_unaligned_access' increases already fixed program counter
and then crash.

for example
   ioctl(fd, TCGETA, (struct termio *)-1)
never return and stay in TASK_UNINTERRUPTIBLE state forever
in my kernel.

Signed-off-by: SUGIOKA Toshinobu <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-21 18:35:55 +09:00
Magnus Damm
3442c0d627 sh: export the sh7343 JPU to user space
This patch exports the sh7343 JPU to user space using uio_pdrv_genirq,
very similar to the sh7722 JPU patch by Hayama-san.

While at it fix up the end of the sh7722 JPU iomem resource.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-21 17:44:26 +09:00
Paul Mundt
5e6136135d sh: Drop the BKL from sys_execve() on SH-5.
Brings it in line with the SH implementation, the BKL is not
necessary here.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-01-21 17:42:55 +09:00
Heiko Carstens
1134723e96 [CVE-2009-0029] Remove __attribute__((weak)) from sys_pipe/sys_pipe2
Remove __attribute__((weak)) from common code sys_pipe implemantation.
IA64, ALPHA, SUPERH (32bit) and SPARC (32bit) have own implemantations
with the same name. Just rename them.
For sys_pipe2 there is no architecture specific implementation.

Cc: Richard Henderson <rth@twiddle.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2009-01-14 14:15:15 +01:00
Heiko Carstens
e55380edf6 [CVE-2009-0029] Rename old_readdir to sys_old_readdir
This way it matches the generic system call name convention.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2009-01-14 14:15:15 +01:00
Yinghai Lu
dee4102a9a sparseirq: use kstat_irqs_cpu instead
Impact: build fix

Ingo Molnar wrote:

> tip/arch/blackfin/kernel/irqchip.c: In function 'show_interrupts':
> tip/arch/blackfin/kernel/irqchip.c:85: error: 'struct kernel_stat' has no member named 'irqs'
> make[2]: *** [arch/blackfin/kernel/irqchip.o] Error 1
> make[2]: *** Waiting for unfinished jobs....
>

So could move kstat_irqs array to irq_desc struct.

(s390, m68k, sparc) are not touched yet, because they don't support genirq

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-01-11 15:53:13 +01:00
Russell King
ba84be2338 remove linux/hardirq.h from asm-generic/local.h
While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)

Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.

It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h.  The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.

My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.

Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.

[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06 15:59:13 -08:00
Linus Torvalds
b840d79631 Merge branch 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
  x86: export vector_used_by_percpu_irq
  x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
  sched: nominate preferred wakeup cpu, fix
  x86: fix lguest used_vectors breakage, -v2
  x86: fix warning in arch/x86/kernel/io_apic.c
  sched: fix warning in kernel/sched.c
  sched: move test_sd_parent() to an SMP section of sched.h
  sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
  sched: activate active load balancing in new idle cpus
  sched: bias task wakeups to preferred semi-idle packages
  sched: nominate preferred wakeup cpu
  sched: favour lower logical cpu number for sched_mc balance
  sched: framework for sched_mc/smt_power_savings=N
  sched: convert BALANCE_FOR_xx_POWER to inline functions
  x86: use possible_cpus=NUM to extend the possible cpus allowed
  x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
  x86: update io_apic.c to the new cpumask code
  x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
  x86: xen: use smp_call_function_many()
  x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
  ...

Fixed up trivial conflict in kernel/time/tick-sched.c manually
2009-01-02 11:44:09 -08:00
Al Viro
18d8fda7c3 take init_fs to saner place
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2008-12-31 18:07:42 -05:00
Linus Torvalds
1db2a5c11e Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (85 commits)
  [S390] provide documentation for hvc_iucv kernel parameter.
  [S390] convert ctcm printks to dev_xxx and pr_xxx macros.
  [S390] convert zfcp printks to pr_xxx macros.
  [S390] convert vmlogrdr printks to pr_xxx macros.
  [S390] convert zfcp dumper printks to pr_xxx macros.
  [S390] convert cpu related printks to pr_xxx macros.
  [S390] convert qeth printks to dev_xxx and pr_xxx macros.
  [S390] convert sclp printks to pr_xxx macros.
  [S390] convert iucv printks to dev_xxx and pr_xxx macros.
  [S390] convert ap_bus printks to pr_xxx macros.
  [S390] convert dcssblk and extmem printks messages to pr_xxx macros.
  [S390] convert monwriter printks to pr_xxx macros.
  [S390] convert s390 debug feature printks to pr_xxx macros.
  [S390] convert monreader printks to pr_xxx macros.
  [S390] convert appldata printks to pr_xxx macros.
  [S390] convert setup printks to pr_xxx macros.
  [S390] convert hypfs printks to pr_xxx macros.
  [S390] convert time printks to pr_xxx macros.
  [S390] convert cpacf printks to pr_xxx macros.
  [S390] convert cio printks to pr_xxx macros.
  ...
2008-12-28 12:33:21 -08:00
Martin Schwidefsky
fc5243d98a [S390] arch_setup_additional_pages arguments
arch_setup_additional_pages currently gets two arguments, the binary
format descripton and an indication if the process uses an executable
stack or not. The second argument is not used by anybody, it could
be removed without replacement.

What actually does make sense is to pass an indication if the process
uses the elf interpreter or not. The glibc code will not use anything
from the vdso if the process does not use the dynamic linker, so for
statically linked binaries the architecture backend can choose not
to map the vdso.

Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2008-12-25 13:38:54 +01:00
Takanari Hayama
7d91fcfcb9 sh: add UIO support for JPU on SH7722.
Add JPU support on Migo-R via UIO. This make use of Magnus's
generic UIO platform driver. Chunk of contiguous memory to hold
intermediate image and compressed data during encode and decode.

Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:49 +09:00
Paul Mundt
5d2685d0b3 sh: Conditionalize the code dumper on CONFIG_DUMP_CODE.
We don't really want this enabled by default, but it is still quite
useful for debugging. So, make it conditional and leave it off by
default.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:47 +09:00
Paul Mundt
740a3e677b sh: Enable skipping of bss on debug platforms for sh32 also.
This enables the same functionality that sh64 has for sh32. When running
on simulated hardware or via remote memory via the debug interface,
memory is gauranteed to be zero on boot already, and skipping the zeroing
of BSS has measurable boot time benefits.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:47 +09:00
Paul Mundt
073da9c0de sh: Kill off cf-enabler with extreme prejudice.
Now that the rest of the boards that were using cf-enabler "generically"
have switched to setting up their mappings on their own, only the mach-se
boards were left using it. All of the cf-enabler using mach-se boards
use a special initialization of the MRSHPC windows rather than going
through the special PTE as other SH-4 platforms do. This consolidates
the MRSHPC setup logic, hooks it up on the boards that care, and gets rid
of any and all remaining references to cf-enabler.

This has been long overdue, as cf-enabler has been the bane of
arch/sh/kernel for the last 7 years. Good riddance.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:46 +09:00
Paul Mundt
43f8f9b95b sh: Simplify kernel_thread_helper() for sh32.
This can use the same implementation as sh64, the generated assembly is
the same between the new and old version, so there is not much point in
leaving it open coded in inline assembly.

This is preparatory work for future consolidation of the _32/_64
variants.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:44 +09:00
Paul Mundt
7b80fb32b3 sh: Kill off mv_heartbeat() from the machvec.
Nothing is using this any more, so get rid of it before anyone gets the
bright idea to start using it again.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:44 +09:00
Paul Mundt
ca0c14e447 sh: Kill off sh_bios_in_gdb_mode().
With the reworked kgdb support, we always detach and reinitialize the
stub. This was mostly a feature for handoffs between sh-ipl+g and the
kgdb stub, but virtually no sh-ipl+g versions ever had this working
right in the first place.

Given that the sh-ipl+g stubs in general use today don't even support
the GDB stub, and we have already killed off the special casing in the
sh-sci serial driver, kill off this now unused symbol too.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:44 +09:00
Paul Mundt
a9df1ed92f sh: export sh_bios_get_node_addr() symbol for stnic module.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:44 +09:00
Paul Mundt
8e32018b04 sh: Run sh_bios through a long overdue Lindent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:44 +09:00
Paul Mundt
180ae2037f sh: Provide sdivsi3/udivsi3/udivdi3 for sh64, kill off libgcc linking.
This moves in the necessary libgcc bits and kills off the libgcc linking
for sh64 kernels as well.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:05 +09:00
Paul Mundt
4466b20cfc sh: Add SH-5 optimized memcpy()/memset()/strcpy()/strlen().
Adopted from the uClibc optimized string versions.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:05 +09:00
Paul Mundt
776d6c298a sh: Kill off remaining CONFIG_SH_KGDB bits.
Now that we use the generic stub, kill off all of the left over
references.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:05 +09:00
Paul Mundt
ab6e570ba3 sh: Generic kgdb stub support.
This migrates from the old bitrotted kgdb stub implementation and moves
to the generic stub. In the process support for SH-2/SH-2A is also added,
which the old stub never provided.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:04 +09:00
Paul Mundt
dd76279b47 sh: Provide linux/regset.h interface for SH-5.
Plugs in general and FPU regsets.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:04 +09:00
Paul Mundt
94e2fb3d3e sh: Provide asm/syscall.h for SH-5.
This provides the asm/syscall.h implementation for sh64 parts.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:04 +09:00
Paul Mundt
6ac034375f sh: Handle cases where setup{_rt,}_frame() fail on SH-5 signal delivery.
Presently these cases are not handled properly due to the return value
not being passed back. This needs to be correct to get proper behaviour
out of things like the tracehook signal notifier, amongst others.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:04 +09:00
Paul Mundt
a99d6fde69 sh: Convert sh64 /proc/asids to debugfs and generic sh.
This converts the sh64 /proc/asids entry to debugfs and enables it for
all SH parts that have debugfs enabled.

On MMU systems this can be used to determine which processes are using
which ASIDs which in turn can be used for finer grained cache tag
analysis.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:03 +09:00
Paul Mundt
4d1f3bbec4 sh: Kill off sh64's unused alloc/free_task_struct() definitions.
These were left over from some time ago, sh64 never got around to
defining __HAVE_ARCH_TASK_STRUCT_ALLOCATOR during the conversion, and it
has no need to. Kill these off and use the generic versions instead.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:03 +09:00
Aoi Shinkai
bd40e81323 sh: Delete unnecessary mov in the interrupt exception entry point.
The INTEVT read at interrupt exception entry is uneccessary, as the read
is deferred until we are ready to enter do_IRQ(). The kgdb nmi path still
requires it, so move it there.

Signed-off-by: Aoi Shinkai <shinkoi2005@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:02 +09:00
Paul Mundt
b5cfeac990 sh: Provide ftrace_make_call()/ftrace_make_nop().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:44:02 +09:00
Magnus Damm
3e51762759 sh: move the hp6xx pm code
Move the not-so-generic pm code from arch/sh/kernel/pm.c to the
platform directory together with the rest of the hp6xx pm code.

This is done to let non-hp6xx platforms enable CONFIG_PM.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:52 +09:00
Magnus Damm
551ea2b40e sh: sh7343 scif configuration update
Fix interrupt values for the first sh7343 SCIF port and
update the configuration to include the remaining 3 ones.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:51 +09:00
Magnus Damm
0c0daec7ca sh: propagate r_clk
Make sure the 32 KHz r_clk rate gets propagated correctly. Without
this fix the clocks for RTC, CMT, KEYSC and RWDT are stuck at 0 Hz.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:51 +09:00
Peter Griffin
2825999e8a sh: Add support for SH7201 CPU subtype.
This patch adds support for the SH-2A FPU based SH7201 processor subtype.

Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:50 +09:00
Paul Mundt
1da1180c6e sh: Split out the idle loop for reuse between _32/_64 variants.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:50 +09:00
Paul Mundt
f74c034d52 sh: do not latency trace idle.
Description snipped from Steven Rostedt's PPC patch:

    When idle is called, interrupts are blocked, but the idle
    function will still wake up on an interrupt. The problem is
    that the interrupt disabled latency tracer will take this call
    to idle as a latency.

    This patch disables the latency tracing when going into idle.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:49 +09:00
Paul Mundt
75fd24c107 sh: Tidy up backtrace formatting with kallsyms disabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:49 +09:00
Paul Mundt
9cfc9a9b6f sh: Add a simple code dumper for SUPERH32 show_regs().
This implements a simple show_code() that is in turn plugged in to
show_regs() to provide minimal code dumping at the end of the trace.

Built on top of a simple instruction disassembler derived from the
binutils opcode table.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:49 +09:00
Paul Mundt
edfd6da040 sh: Add a few more branch types to the branch emulator.
This plugs in some extra encodings for matching more bsr/bsrf/jsr
branches.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:49 +09:00
Paul Mundt
624c6a6750 sh: More movmem alias symbol exports for older compilers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:43:49 +09:00
Paul Mundt
9ef100287a sh: Add exports for __udivsi3/__sdivsi3 and the _i4 versions.
Needed by older compilers.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:54 +09:00
Paul Mundt
1aad54a99b sh: Migrate necessary libgcc bits in to arch/sh/lib for SUPERH32.
This moves in the necessary libgcc bits for SUPERH32 and drops the
libgcc linking for the regular targets. This in turn allows us to rip
out quite a few hacks both in sh_ksyms_32 and arch/sh/Makefile.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:53 +09:00
Paul Mundt
e9bf51e5cc sh: __udivdi3 -> do_div() in softfloat lib.
Inhibit the generation of __udivdi3 for the softfloat lib, use do_div()
outright.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:53 +09:00
Paul Mundt
00e825c6b9 sh: Fix clock framework compiler warnings.
CC      arch/sh/kernel/cpu/clock.o
  arch/sh/kernel/cpu/clock.c: In function 'clk_disable':
  arch/sh/kernel/cpu/clock.c:156: warning: 'return' with a value, in function returning void

Introduced by ("sh: enable and disable clocks recursively").

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:53 +09:00
Matt Fleming
fad57feba7 sh: dynamic ftrace support.
First cut at dynamic ftrace support.

Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:52 +09:00
Magnus Damm
ef6aff6884 sh: remove old sh_mobile mstpc clocks
Remove the old sh_mobile mstpcr clocks.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:52 +09:00
Magnus Damm
765786e0ae sh: sh_mobile usb clock framework support
Add clock framework support to the usb/r8a66597 driver and
adjust the cpu specific code accordingly.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:51 +09:00
Magnus Damm
af5be79a7f sh: sh_mobile usbf clock framework support
Add clock framework support to the usbf/m66592 driver and
adjust the cpu specific code accordingly.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:51 +09:00
Magnus Damm
a5616bd0f1 sh: sh_mobile i2c clock framework support
Add clock framework support to the sh_mobile i2c driver and
adjust the processor specific code accordingly.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:51 +09:00
Magnus Damm
f2eb0109fb sh: sh_mobile mstpcr clocks for sh7366
Add sh7366 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:51 +09:00
Magnus Damm
6e88d030a1 sh: sh_mobile mstpcr clocks for sh7343
Add sh7343 mstpcr bits and information about their parent clocks.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:50 +09:00
Magnus Damm
f14c017d6b sh: sh_mobile mstpcr clocks for sh7723
Add sh7723 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:50 +09:00
Magnus Damm
ecf399bdaf sh: sh_mobile mstpcr clocks for sh7722
Add sh7722 mstpcr bits and information about their parent clocks.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:50 +09:00
Magnus Damm
7c7e02a28b sh: new sh_mobile mstpcr clocks base code
Add base code to handle new mstpcr clocks. Make sure clock rates propagate.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:50 +09:00
Magnus Damm
1dc7b776d9 sh: use arch_flags for sh_mobile mstpcr clock bits
Use arch_flags to keep track of register and flag number.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:50 +09:00
Magnus Damm
d902d04f54 sh: sh_mobile clock divider index fix
Use divider index value instead of divider value.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:50 +09:00
Magnus Damm
d12cfac146 sh: enable and disable clocks recursively
Recurse and make sure parent clocks get enabled/disabled.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:50 +09:00
Paul Mundt
4a4a9be3eb sh: Move arch_get_unmapped_area() in to arch/sh/mm/mmap.c.
Now that arch/sh/mm/mmap.c exists, move arch_get_unmapped_area() there.
Follows the ARM change.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-12-22 18:42:49 +09:00
Rusty Russell
320ab2b0b1 cpumask: convert struct clock_event_device to cpumask pointers.
Impact: change calling convention of existing clock_event APIs

struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.

Another single-patch change.  For safety, we BUG_ON() in
clockevents_register_device() if it's not set.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
2008-12-13 21:20:26 +10:30
Rusty Russell
98a79d6a50 cpumask: centralize cpu_online_map and cpu_possible_map
Impact: cleanup

Each SMP arch defines these themselves.  Move them to a central
location.

Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
   CONFIG_INIT_ALL_POSSIBLE for this rather than break them.

2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
   Those archs simply have phys_cpu_present_map replaced everywhere.

3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
   so I just manipulate them both in sync.

4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
   declarations.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
2008-12-13 21:19:41 +10:30
Paul Mundt
272966c070 serial: sh-sci: Reorder the SCxTDR write after the TDxE clear.
Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.

Signed-off-by: Vladimir Prus <vladimir@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-11-13 17:46:06 +09:00
Francesco VIRLINZI
2cd0ebc83d sh: Fixed the TMU0 reload value on resume
This patch fixes the TMU0 interrupt frequency on suspend/resume.
During the resume the kernel reprograms the TMU0.ClockEvent mode
but if the mode is periodic than the TMU0.TCOR is updated with
a random wrong value without taking care latest valid saved value.

There was no problem with No_HZ system where TMU0.TCOR isn't used.

Signed-off-by: Francesco M. Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-11-13 17:40:30 +09:00
Magnus Damm
bfbedf787c sh: early printk port type fix
Add PORT_SCIF to unbreak the early printk code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-11-13 15:37:07 +09:00
Yoshihiro Shimoda
51ee3d92bf fix sci type for SH7723
This patch changes sci type of SH7723 from PORT_SCI to PORT_SCIFA.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-11-12 12:29:56 +09:00
Paul Mundt
694f94f263 sh: FTRACE renamed to FUNCTION_TRACER.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-31 16:20:36 +09:00
Kuninori Morimoto
47c2968c84 Add support usb setting on sh 7366
This patch add usb setting for sh 7366

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-31 16:03:30 +09:00
Paul Mundt
b4d36a254f sh: Add on-chip RTC support for SH7722.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-28 18:40:19 +09:00
Paul Mundt
8a2fd5f3ab sh: Fix FPU tuning on toolchains with mismatched multilib targets.
Presently there is very little standing in the way of using an SH-4
toolchain for building an SH-2 kernel, and vice versa. Binutils itself
has no limitations whatsoever and supports explicit ISA hinting, which
we already use with varying degrees of success today.

This leaves GCC as the odd one out, due to a rather dubious policy
decision by the GCC folks to not include all of the CPU family variants
in the default list of multilib targets in GCC4. Despite best efforts to
the contrary, libgcc itself already contains awareness of the various CPU
types and remains generally usable, allowing it to safely be referenced
even on a mismatched target (and indeed, explicit ISA tuning by binutils
keeps us honest in terms of ensuring that we do not link incompatible
objects in).

In order to support this, a couple of changes had to be made. Firstly,
the introduction of MAYBE_DECLARE_EXPORT(), which provides a __weak
extern reference for libgcc resident routines when finer-grained
-m<cpu-family> based tuning is not supported by the toolchain. This
fixes up the __sdivsi3_i4i and __udivsi3_i4i references when dealing
with SH-2 kernels linked with an SH-4 libgcc. Secondly, in case where we
are unable to find a suitable match for CPU family tuning but still
have a toolchain that defaults to FP instruction generation, a suitable
nofpu target must be selected. This is accomplished by selecting the
first nofpu multilib target supported by the toolchain, which is
also necessary for selecting the proper libgcc to link against.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-28 17:19:35 +09:00
Magnus Damm
0835f127e5 sh: sh7785 pinmux support
This patch implements pinmux tables for the sh7785 processor.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-23 11:59:37 +09:00
Paul Mundt
6f8f6daa6d sh: Kill off unused p1fc divisors from SH7763 clk fwk.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-22 19:38:30 +09:00
Magnus Damm
42eed42bac sh: improve pinmux support for single direction pins
This patch improves the support for gpio pins that are hard wired
to either input or output and lack control register association.
A special force enum id is used to allow use without control
register but still mark the gpio pin as input or output.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-22 18:34:16 +09:00
Magnus Damm
ed0b2ef55a sh: Update gpio_set_value() pin value handling
This patch updates the pinmux code to use the boolean value for
the function gpio_set_value(). Without this patch values other
than 0 and 1 will result in incorrect GPIO settings.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-21 21:41:23 +09:00
Paul Mundt
2bba37e64a sh: Export cache flush routines needed by sh_eth on SH7619.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-21 19:45:08 +09:00
Paul Mundt
c9306f0efb sh: Wire up oops reporting in the die notifier chain.
Commit 3f5a54e371 ("ftrace: dump out ftrace
buffers to console on panic") added an ftrace buffer dumper that hooks
in to the die notifier chain and dumps out data in the oops path.

Unfortunately SH supported ftrace but didn't support DIE_OOPS, so add
that in and get it building again.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-21 18:33:36 +09:00
Paul Mundt
7dd0558d70 sh: Hook up PB0->PB7 input-only pins in SH7203 PFC.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-21 18:09:43 +09:00
Paul Mundt
b56050ae5e sh: arch/sh/kernel/smp.c needs linux/cpu.h for notify_cpu_starting().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-21 12:51:51 +09:00
Paul Mundt
a51413a65f sh: Fix up the SH7203 build.
The sh7203.h include paths were missed in the previous update, so switch
the include path to cpu/ as with the rest.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-21 12:51:51 +09:00
Linus Torvalds
ed402af3c2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
  sh: Move SH-4 CPU headers down one more level.
  sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
  sh: Migrate common board headers to mach-common/.
  sh: Move the CPU definition headers from asm/ to cpu/.
  serial: sh-sci: Add support SCIF of SH7723
  video: add sh_mobile_lcdc platform flags
  video: remove unused sh_mobile_lcdc platform data
  sh: remove consistent alloc cruft
  sh: add dynamic crash base address support
  sh: reduce Migo-R smc91x overruns
  sh: Fix up some merge damage.
  Fix debugfs_create_file's error checking method for arch/sh/mm/
  Fix debugfs_create_dir's error checking method for arch/sh/kernel/
  sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
  sh: Use sh7720 GPIO on magicpanelr2 board
  sh: Add sh7720 pinmux code
  sh: Use sh7203 GPIO on rsk7203 board
  sh: Add sh7203 pinmux code
  sh: Use sh7723 GPIO on AP325RXA board
  sh: Add sh7723 pinmux code
  ...
2008-10-20 09:13:34 -07:00
Vivek Goyal
57cac4d188 kdump: make elfcorehdr_addr independent of CONFIG_PROC_VMCORE
o elfcorehdr_addr is used by not only the code under CONFIG_PROC_VMCORE
  but also by the code which is not inside CONFIG_PROC_VMCORE.  For
  example, is_kdump_kernel() is used by powerpc code to determine if
  kernel is booting after a panic then use previous kernel's TCE table.
  So even if CONFIG_PROC_VMCORE is not set in second kernel, one should be
  able to correctly determine that we are booting after a panic and setup
  calgary iommu accordingly.

o So remove the assumption that elfcorehdr_addr is under
  CONFIG_PROC_VMCORE.

o Move definition of elfcorehdr_addr to arch dependent crash files.
  (Unfortunately crash dump does not have an arch independent file
  otherwise that would have been the best place).

o kexec.c is not the right place as one can Have CRASH_DUMP enabled in
  second kernel without KEXEC being enabled.

o I don't see sh setup code parsing the command line for
  elfcorehdr_addr.  I am wondering how does vmcore interface work on sh.
  Anyway, I am atleast defining elfcoredhr_addr so that compilation is not
  broken on sh.

Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:39 -07:00
Paul Mundt
ebf9c118df sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
The pinmux management is tied in to this code, while it is presently only
used by platforms that select GENERIC_GPIO. The asm/gpio.h definitions
are not referenced when GENERIC_GPIO is disabled, resulting in a build
failure for all of the platforms that don't select it.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 13:04:06 +09:00
Paul Mundt
f727565013 sh: Move the CPU definition headers from asm/ to cpu/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 12:04:53 +09:00
Magnus Damm
4aeaa22343 sh: add dynamic crash base address support
Add support for dynamic crash kernel base address.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 11:38:40 +09:00
Paul Mundt
9a19eb2a66 sh: Fix up some merge damage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 11:37:58 +09:00
Paul Mundt
4cb40f795a Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	Documentation/kernel-parameters.txt
	arch/sh/include/asm/elf.h
2008-10-20 11:17:52 +09:00
Paul Mundt
79ed2a9216 Merge branch 'sh/gpiolib' 2008-10-20 10:40:32 +09:00
Zhaolei
9986b311ef Fix debugfs_create_dir's error checking method for arch/sh/kernel/
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.

Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 10:40:15 +09:00
Magnus Damm
c9c3c1b74d sh: Add sh7720 pinmux code
This patch adds pinmux and gpio support for the sh7720 processor.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 10:34:25 +09:00
Magnus Damm
41e4a9a5e2 sh: Add sh7203 pinmux code
This patch adds pinmux and gpio support for the sh7203 processor.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 10:34:18 +09:00
Magnus Damm
0436ec15ae sh: Add sh7723 pinmux code
This patch adds pinmux and gpio support for the sh7723 processor.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 10:34:12 +09:00
Magnus Damm
8d7b5b0af7 sh: Add sh7722 pinmux code
This patch adds pinmux and gpio support for the sh7722 processor.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 10:34:05 +09:00
Magnus Damm
2967dab1ae sh: GPIO and pinmux base code
This patch adds gpio code together with the pinmux table parser.
In the future we should optimize this and switch back to gpiolib.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-20 10:33:50 +09:00
Paul Mundt
14866543ad sh: More I/O routine overhauling.
This tidies up a lot of the PIO/MMIO split. No in-tree platforms were
making use of the MMIO overloading through the machvec (nor have any of
them been in some time), so we just kill all of that off. The ISA I/O
routine wrapping remains unaffected, which remains the only special
casing outside of the iomap API that boards need to think about.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-04 05:25:52 +09:00
Paul Mundt
bbfbd8b151 sh: Move the shared INTC code out to drivers/sh/
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-01 16:13:54 +09:00
Paul Mundt
62429e0364 sh: Use __raw_xxx() I/O accessors for INTC and IPR.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-10-01 15:19:10 +09:00
Paul Mundt
4d01cdafba sh: SH-5 clk fwk support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-29 20:09:17 +09:00
Paul Mundt
091db04559 sh: Fix up signal_64 cast warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-29 19:44:40 +09:00
Paul Mundt
1bec157a1f sh: Force pending restarted system calls to return -EINTR.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-24 14:37:35 +09:00
Paul Mundt
e7ab3cd251 sh: Add FPU registers to regset interface.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-21 19:04:55 +09:00
Paul Mundt
9d2b1f81dd sh: ftrace support.
This adds support for ftrace to SH. This only includes CONFIG_FTRACE,
and does not handle dynamic ftrace presently.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-21 16:43:45 +09:00
Paul Mundt
3d58695edb sh: Trivial trace_mark() instrumentation for core events.
This implements a few trace points across events that are deemed
interesting. This implements a number of trace points:

	- The page fault handler / TLB miss
	- IPC calls
	- Kernel thread creation

The original LTTng patch had the slow-path instrumented, which
fails to account for the vast majority of events. In general
placing this in the fast-path is not a huge performance hit, as
we don't take page faults for kernel addresses.

The other bits of interest are some of the other trap handlers, as
well as the syscall entry/exit (which is better off being handled
through the tracehook API). Most of the other trap handlers are corner
cases where alternate means of notification exist, so there is little
value in placing extra trace points in these locations.

Based on top of the points provided both by the LTTng instrumentation
patch as well as the patch shipping in the ST-Linux tree, albeit in a
stripped down form.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-21 13:56:39 +09:00
Paul Mundt
4c59e2942e sh: Move lookup_exception_vector() out to asm/system_32.h.
There are other places where we want to have access to the trap/exception
number, so move out the lookup_exception_vector() helper. While we're at
it, refactor it slightly to return the vector instead.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-21 12:00:23 +09:00
Paul Mundt
8a80a5e9e8 sh: Fix up signal_64 conflicting handle_signal() definition.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-17 23:14:36 +09:00
Paul Mundt
b3d765f5df sh: Fix up fpu emu build.
The addition of the kprobes code pushed down a variable declaration,
clean it up.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-17 23:12:11 +09:00
Paul Mundt
5a89f1adbc sh: latencytop support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-13 01:44:03 +09:00
Paul Mundt
0e660d2d43 sh: Tidy up ELF core dumps.
These have been using overrides for ELF_CORE_COPY_TASK_REGS and
ELF_CORE_COPY_FPREGS while the generic versions can be used instead.
Presently the pt_regs are also duplicated across elf_core_copy_regs()
and elf_core_copy_task_regs(), this switches to simply copying out
through elf_core_copy_regs() instead.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-12 23:27:46 +09:00
Paul Mundt
72461997c3 sh: Check SR.DSP bit for DSP regset validity.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-12 22:56:35 +09:00
Paul Mundt
f9540ececa sh: Add missing task_user_regset_view() definition.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-12 22:42:43 +09:00
Paul Mundt
5dadb34394 sh: Add DSP registers to regset interface.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-12 22:42:10 +09:00
Paul Mundt
f8b890ab4c sh: Flag T-bit for syscall restart.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-12 22:08:20 +09:00
Paul Mundt
934135c19d sh: ptrace: Introduce user_regset interface for gp regs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-12 19:52:36 +09:00
roel kluin
b21a910435 sh: intc_prio_data() test before subtraction on unsigned
bit is unsigned, so test before subtraction

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-10 12:01:46 +09:00
Paul Mundt
6eb2139b3d sh: kprobes: kretprobe_trampoline needs to be global.
Needed by CONFIG_TRACING.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-09 08:13:28 +09:00
Manfred Spraul
e545a6140b kernel/cpu.c: create a CPU_STARTING cpu_chain notifier
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.

The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.

Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-08 19:25:24 +02:00
Paul Mundt
cf204fa797 sh: Derive calibrate_delay lpj from clk fwk.
All CPUs must have a sensible cpu_clk definition these days, which we can
safely use for deriving the preset loops_per_jiffy. The only odd one out
is SH-5, which hasn't been hammered in to the framework yet.

Based on the ST patch.

Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 20:47:42 +09:00
Paul Mundt
4eb5845d6c sh: kprobes: __kprobes annotations and formatting cleanups.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 18:22:47 +09:00
Paul Mundt
734db3770d sh: kprobes: Fix up race against probe point removal.
Handle a corner case where another CPU or debugger removes the probe
point from underneath us.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 18:15:55 +09:00
Paul Mundt
247bc6d2ae sh: kprobes: Fix up a preemption imbalance on jprobe return.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 18:14:50 +09:00
Paul Mundt
ee386de774 sh: kprobes: Default to NOTIFY_DONE for unhandled debug traps.
Presently this is doing a force_sig() SIGTRAP, which is already taken
care of in the generic code if no one asserts NOTIFY_STOP. Switch the
default return to NOTIFY_DONE in the case of unhandled traps, so that
the same trap may pass through to other users on the same die chain.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 18:12:33 +09:00
Paul Mundt
174b5c9923 sh: kprobes: Use trapa #0x3a for breakpoint trap.
Not all parts support trapa #0xff, so use something within the debug trap
range that's accessible on all parts.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 18:10:10 +09:00
Paul Mundt
037c10a612 sh: kprobes: Hook up kprobe_fault_handler() in the page fault path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 12:22:47 +09:00
Paul Mundt
e7cb016e5a sh: Mark kretprobe_trampoline_holder static and __used.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 12:02:17 +09:00
Luca Santini
53abf911fa sh: Enable IRLM mode for SH7760 IRQ_MODE_IRQ.
Follows the same setting as SH7750.

Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 11:54:56 +09:00
Chris Smith
d39f545014 sh: Add kprobes support.
Initial support for kprobes/kretprobes for 32-bit SH platforms.

[ General cleanup and some rework for the kretprobe hash lock. -- PFM ]

Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:05 +09:00
Francesco Virlinzi
61c66387e6 sh: fix the TMU code to allow a fully running NO_HZ system
This patch fixes the TMU code to allow NO_HZ to work on sh

Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:05 +09:00
Carl Shaw
b6ad1e8c3f sh: Subnormal double to float conversion
This patch adds support for the SH4 to convert a subnormal double
into a float by catching the FPE and implementing the FCNVDS
instruction in software.

Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:05 +09:00
Stuart Menefy
f040ddaf4c sh: Fix an unusual memory initialisation error.
This fixes a problems with the set up of Linux memory:

 - When reserving memory at boot time, the code previously reserved
   the bottom page of memory, and then from one page up to the end of
   the bootmap. This had the desired effect, but was strictly speaking
   wrong, as the one page was actually whatever CONFIG_ZERO_PAGE_OFFSET
   had been set to.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:05 +09:00
Stuart Menefy
28d6e52cf7 sh: Fix up broken 32-bit initrd support.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:04 +09:00
Paul Mundt
fa43972fab sh: fixup many sparse errors.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:04 +09:00
Paul Mundt
7d96169cb7 sh: Display CPU information in show_regs().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:03 +09:00
Paul Mundt
53c01d2dc3 sh: Early dummy clockevent registration on boot CPU.
The dummy timer needs to be registered on the boot CPU before the
system timer clockevent is registered, or broadcasting doesn't work
as advertized.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:03 +09:00
Paul Mundt
71f0bdcab6 sh: smp: shove a cpu_relax() in the plat_start_cpu() busy loop.
Without this, certain versions of GCC will happily optimize the entire
loop out.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:03 +09:00
Paul Mundt
8c24594dea sh: generic clockevent broadcast support.
This hooks up GENERIC_CLOCKEVENTS_BROADCAST and a dummy local timer,
which we call in to from the timer IPI when no other local timer is
provided.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:03 +09:00
Paul Mundt
6f52707e68 sh: smp: Hook up a timer IPI stub.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:03 +09:00
Paul Mundt
c7936b9abc sh: smp: Hook in to the generic IPI handler for SH-X3 SMP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:03 +09:00
Paul Mundt
173a44dd1f sh: smp: Provide a generic IPI handler.
This provides a generic smp_message_recv() routine (based on the PPC
one), that IPI IRQs can wrap in to.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-08 10:35:02 +09:00
Paul Mundt
dbce1f649e sh64: resume_kernel fix for kernel oops built with CONFIG_BKL_PREEMPT=y.
Follows the SH change.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-05 14:51:28 +09:00
Carmelo Amoroso
323b8c410a sh: resume_kernel fix for kernel oops built with CONFIG_BKL_PREEMPT=y.
This patch fixes a problem within the SH implementation of resume_kernel code,
that implements in assembly the bulk of preempt_schedule_irq function without
taking care of the extra code needed to handle the BKL preemptible.

The patch basically consists of removing this asm code and calling the common
C implementation (see kernel/sched.c) as other archs do.

Another change is the missing 'cli' macro invocation at the beginning of
the resume_kernel.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-09-05 14:42:16 +09:00
Yoshihiro Shimoda
3c31bf7313 sh: fix semtimedop syscall
fix the problem that cannot work semtimedop system call.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-28 14:53:22 +09:00
Magnus Damm
5734493bac sh: fix kexec entry point for crash kernels
The crash kernel entry point is currently checked by the kexec kernel
code and only physical addresses in the reserved memory window are
accepted. This means that we can't pass P2 or P1 addresses as entry
points in the case of crash kernels. This patch makes sure we can start
crash kernels by adding support for physical address entry points.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-28 14:53:03 +09:00
Magnus Damm
34894c7843 sh: crash kernel resource fix
The reserved crash kernel memory range is currently missing from
/proc/iomem. crashk_res is mistakenly setup after __add_active_range().
Reorder things to make sure the resource shows up in /proc/iomem.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-28 14:52:58 +09:00
Adrian Bunk
e311be521f sh: fix ptrace_64.c:user_disable_single_step()
This patch fixes the following compile error caused by
commit c459dbf294
(sh: ptrace single stepping cleanups.):

<--  snip  -->

...
  CC      arch/sh/kernel/ptrace_64.o
arch/sh/kernel/ptrace_64.c: In function 'user_disable_single_step':
arch/sh/kernel/ptrace_64.c:134: error: 'regs' undeclared (first use in this function)
arch/sh/kernel/ptrace_64.c:134: error: (Each undeclared identifier is reported only once
arch/sh/kernel/ptrace_64.c:134: error: for each function it appears in.)
...
make[2]: *** [arch/sh/kernel/ptrace_64.o] Error 1

<--  snip  -->

Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-25 14:08:02 +09:00
Magnus Damm
2a5323cd69 sh: export sh7723 VEU as VEU2H
Export sh7723 VEU hardware blocks as VEU2H. The sh7723 VEU2H differs
a bit from the sh7722 VEU so use different names for our UIO devices.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-11 20:17:55 +09:00
Yoshinori Sato
d09d328c11 sh: Don't export __{s,u}divsi3_i4i from SH-2 libgcc.
rsk7203_defconfig fails to build with the following error:

<--  snip  -->

...
  LD      .tmp_vmlinux1
arch/sh/kernel/built-in.o:(__ksymtab+0xb8): undefined reference to `__udivsi3_i4i'
arch/sh/kernel/built-in.o:(__ksymtab+0xc8): undefined reference to `__sdivsi3_i4i'
make[1]: *** [.tmp_vmlinux1] Error 1

<--  snip  -->

That worked with 2.6.26, and these are far less undefined references
than in the cases where libgcc was missing.

[ These symbols are not defined on SH-2 versions of libgcc, so we have to
  special case the export there. - Paul ]

Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-11 20:17:49 +09:00
Paul Mundt
c3b4adfa65 sh: Save NUMA node data in vmcore for crash dumps.
Presently the NUMA node data isn't saved on kexec. This implements a
simple arch_crash_save_vmcoreinfo() for saving off the relevant data.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-04 13:42:49 +09:00
Paul Mundt
4b59c97325 sh: module_alloc() should be using vmalloc_exec().
SH-X2 extended mode TLB allows for toggling of the exec bit, so make
sure we are using the right protection bits for module space there
also.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-04 13:34:29 +09:00
Paul Mundt
3108cf0612 sh: Fix up __bug_table handling in module loader.
We should be calling in to the lib/bug.c module helpers, fix that up.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-04 13:32:04 +09:00
Paul Mundt
6a9545bd95 sh: Fix up broken kerneldoc comments.
These were completely unparseable, so fix them up.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-04 12:51:06 +09:00
Paul Mundt
9e5e21170e sh: Fix up the audit arch endian specification.
Presently this was always being set to AUDIT_ARCH_SH, which assumes
big endian. Fix this up so that the architecture actually reflects
what we're running on.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-02 04:39:33 +09:00
Paul Mundt
ab99c733ae sh: Make syscall tracer use tracehook notifiers, add TIF_NOTIFY_RESUME.
This follows the changes in commits:

7d6d637dac
4f72c4279e

on powerpc. Adding in TIF_NOTIFY_RESUME, and cleaning up the syscall
tracing to be more generic. This is an incremental step to turning
on tracehook, as well as unifying more of the ptrace and signal code
across the 32/64 split.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-02 04:39:33 +09:00
Paul Mundt
c459dbf294 sh: ptrace single stepping cleanups.
This converts the single stepping done by sh/sh64 ptrace implementations
to use the generic user_enable/disable_single_step(), and subsequently
rips out a lot of ptrace request cases that are now handled generically.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-02 04:39:33 +09:00
Paul Mundt
c4637d4751 sh: seccomp support.
This hooks up the seccomp thread flag and associated callback from the
syscall tracer.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-02 04:39:32 +09:00
Paul Mundt
cec3fd3e2a sh: Tidy up the _TIF work masks, and fix syscall trace bug on singlestep.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-02 04:39:32 +09:00
Simon Horman
daf423db3b kdump: sh: parse elfcorehdr command line argument
A quick cut and paste from other architectures to allow SH
to parse the elfcorehdr command line argument which is required
for both is_kdump_kernel() and vmcore to function.
(the former is as yet unused on SH).

Tested compilation only

Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-08-02 04:39:32 +09:00
Paul Mundt
939a24a6df sh: Move out the solution engine headers to arch/sh/include/mach-se/
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-29 21:41:37 +09:00
Paul Mundt
b9edb17cc2 sh: Add an arch/sh/kernel/.gitignore
Ignore vmlinux.lds.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-29 08:29:32 +09:00
Paul Mundt
f15cbe6f1a sh: migrate to arch/sh/include/
This follows the sparc changes a439fe51a1.

Most of the moving about was done with Sam's directions at:

http://marc.info/?l=linux-sh&m=121724823706062&w=2

with subsequent hacking and fixups entirely my fault.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-29 08:09:44 +09:00
Paul Mundt
44f9598952 sh: Wire up new syscalls.
This wires up the signalfd4, eventfd2, epoll_create1, dup3, pipe2, and
inotify_init1 syscalls.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:34:45 +09:00
Stuart MENEFY
0b1689cfbb sh: Don't miss pending signals returning to user mode after signal processing
Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.

This is the SH version of commit c3ff8ec31c
which was for the i386.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:37 +09:00
Magnus Damm
d7f1a9adc0 sh: Use clk_always_enable() on sh7366
Use clk_always_enable() in the sh7366 processor code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:37 +09:00
Magnus Damm
8fa509ab91 sh: Use clk_always_enable() on sh7343 / SE77343
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:37 +09:00
Magnus Damm
6c7d826cf6 sh: Use clk_always_enable() on sh7722 / Migo-R / SE7722
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:37 +09:00
Magnus Damm
9ca6ecac50 sh: Use clk_always_enable() on sh7723 / ap325rxa
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:37 +09:00
Magnus Damm
152fe36ebe sh: Show all clocks and their state in /proc/clocks
Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:36 +09:00
Magnus Damm
1312994c80 sh: Merge sh7343 and sh7722 clock code
This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.

With this change all SuperH Mobile devices now use the same clock code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:36 +09:00
Magnus Damm
aea167cbb5 sh: Add SuperH Mobile MSTPCR bits to clock framework
Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:36 +09:00
Magnus Damm
3fec18bd60 sh: Use arch_flags to simplify sh7722 siu clock code
Make use of arch_flags to simplify the SIU clock code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:36 +09:00
Magnus Damm
1eca5c9272 sh: Add memory chunks to SH-Mobile UIO devices
This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:35 +09:00
Magnus Damm
714750dd5c sh: Export sh7366 VPU, VEU(1), VEU(2) using uio_pdrv_genirq
This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.

While at it, fix up the VEU(2) interrupt vector.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:34 +09:00
Magnus Damm
6874548c69 sh: Export sh7723 VPU, VEU2H0, VEU2H1 using uio_pdrv_genirq
This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:34 +09:00
Magnus Damm
a55f6d2567 sh: Export sh7722 VPU and VEU using uio_pdrv_genirq
This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:34 +09:00
Magnus Damm
c901c96cc2 sh: Export sh7343 VPU and VEU using uio_pdrv_genirq
This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:34 +09:00
Yoshinori Sato
6e80f5e8c4 sh2(A) exception handler update
This patch is

By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize

By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:34 +09:00
Yoshihiro Shimoda
a4e1d08491 sh: update sh7343 code
updated the following codes for SH7343:
 - add register_intc_controller()
 - add EARLY_SCIF_CONSOLE_PORT
 - add define of CPG register

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:34 +09:00
Magnus Damm
0fff76f2da sh: add SuperH Mobile I2C platform data to sh7366
This patch adds platform data for the single I2C channel on sh7366.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:33 +09:00
Magnus Damm
da7d3029d1 sh: add SuperH Mobile I2C platform data to sh7723
This patch adds platform data for the single I2C channel on sh7723.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:33 +09:00
Magnus Damm
7549079d84 sh: add SuperH Mobile I2C platform data to sh7343
This patch adds platform data for two I2C channels to the sh7343.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:33 +09:00
Yoshihiro Shimoda
6bdfb22a8e sh: add interrupt ack code to sh4a
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:33 +09:00
Stuart Menefy
f2fb4e4f64 sh: Conditionally re-enable IRQs in fault path.
The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.

It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:33 +09:00
Paul Mundt
068f59143d sh: Record the major cut revision for probed SH-4A parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:32 +09:00
Chris Smith
09b5a10c19 sh: Optimized flush_icache_range() implementation.
Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().

Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:32 +09:00
Stuart Menefy
3611ee7acc sh: Stub in silicon cut in CPU info.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:32 +09:00
Paul Mundt
ef9247ef89 sh: Tidy up the SH-3 exception vector table.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:32 +09:00
Yoshinori Sato
d88a3ea6fa SH7619 add ethernet controler support
- Add EtherC + PHY resource define.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:32 +09:00
Adrian Bunk
4c1cfab1e0 sh/kernel/ cleanups
This patch contains the following cleanups:
- make the following needlessly global code static:
  - cf-enabler.c: cf_init()
  - cpu/clock.c: __clk_enable()
  - cpu/clock.c: __clk_disable()
  - process_32.c: default_idle()
  - time_32.c: struct clocksource_sh
  - timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
  - process_{32,64}.c: disable_hlt()
  - process_{32,64}.c: enable_hlt()

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:30 +09:00
Nobuhiro Iwamatsu
c63847a362 sh: Add SCIF2 support for SH7763.
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:29 +09:00
Paul Mundt
2cd1e31859 sh: Make dump_task dependent on ELF core.
Currently this is only linked in for CONFIG_BINFMT_ELF, make it dependent
on CONFIG_ELF_CORE, so it's both selectable there and also linked in for
CONFIG_BINFMT_ELF_FDPIC.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:28 +09:00
Paul Mundt
3bc24a1a54 sh: Initial ELF FDPIC support.
This adds initial support for ELF FDPIC on MMU-less SH, as per version
0.2 of the ABI definition at:

	http://www.codesourcery.com/public/docs/sh-fdpic/sh-fdpic-abi.txt

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:28 +09:00
Adrian Bunk
b19a33caba sh: export get_cpu_subtype
This patch fixes the following build error:

<--  snip  -->

...
  MODPOST 1837 modules
ERROR: "get_cpu_subtype" [arch/sh/oprofile/oprofile.ko] undefined!
...
make[2]: *** [__modpost] Error 1

<--  snip  -->

Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2008-07-28 18:10:27 +09:00
Huang Ying
3ab8352137 kexec jump
This patch provides an enhancement to kexec/kdump.  It implements the
following features:

- Backup/restore memory used by the original kernel before/after
  kexec.

- Save/restore CPU state before/after kexec.

The features of this patch can be used as a general method to call program in
physical mode (paging turning off).  This can be used to call BIOS code under
Linux.

kexec-tools needs to be patched to support kexec jump. The patches and
the precompiled kexec can be download from the following URL:

       source: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-src_git_kh10.tar.bz2
       patches: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-patches_git_kh10.tar.bz2
       binary: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec_git_kh10

Usage example of calling some physical mode code and return:

1. Compile and install patched kernel with following options selected:

CONFIG_X86_32=y
CONFIG_KEXEC=y
CONFIG_PM=y
CONFIG_KEXEC_JUMP=y

2. Build patched kexec-tool or download the pre-built one.

3. Build some physical mode executable named such as "phy_mode"

4. Boot kernel compiled in step 1.

5. Load physical mode executable with /sbin/kexec. The shell command
   line can be as follow:

   /sbin/kexec --load-preserve-context --args-none phy_mode

6. Call physical mode executable with following shell command line:

   /sbin/kexec -e

Implementation point:

To support jumping without reserving memory.  One shadow backup page (source
page) is allocated for each page used by kexeced code image (destination
page).  When do kexec_load, the image of kexeced code is loaded into source
pages, and before executing, the destination pages and the source pages are
swapped, so the contents of destination pages are backupped.  Before jumping
to the kexeced code image and after jumping back to the original kernel, the
destination pages and the source pages are swapped too.

C ABI (calling convention) is used as communication protocol between
kernel and called code.

A flag named KEXEC_PRESERVE_CONTEXT for sys_kexec_load is added to
indicate that the loaded kernel image is used for jumping back.

Now, only the i386 architecture is supported.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-26 12:00:04 -07:00
Linus Torvalds
ecc8b655b3 Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
  nohz: prevent tick stop outside of the idle loop
2008-07-24 12:55:01 -07:00
Linus Torvalds
2528ce3237 Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  arch/mips/kernel/stacktrace.c: Heiko can't type
  kthread: reduce stack pressure in create_kthread and kthreadd
  fix core/stacktrace changes on avr32, mips, sh
2008-07-24 12:54:26 -07:00
Ulrich Drepper
ed8cae8ba0 flag parameters: pipe
This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value.  This patch implements
the handling of O_CLOEXEC for the flag.  I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation.  I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.

The implementation introduces do_pipe_flags.  I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code.  To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags.  Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.

The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>

#ifndef __NR_pipe2
# ifdef __x86_64__
#  define __NR_pipe2 293
# elif defined __i386__
#  define __NR_pipe2 331
# else
#  error "need __NR_pipe2"
# endif
#endif

int
main (void)
{
  int fd[2];
  if (syscall (__NR_pipe2, fd, 0) != 0)
    {
      puts ("pipe2(0) failed");
      return 1;
    }
  for (int i = 0; i < 2; ++i)
    {
      int coe = fcntl (fd[i], F_GETFD);
      if (coe == -1)
        {
          puts ("fcntl failed");
          return 1;
        }
      if (coe & FD_CLOEXEC)
        {
          printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
          return 1;
        }
    }
  close (fd[0]);
  close (fd[1]);

  if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
    {
      puts ("pipe2(O_CLOEXEC) failed");
      return 1;
    }
  for (int i = 0; i < 2; ++i)
    {
      int coe = fcntl (fd[i], F_GETFD);
      if (coe == -1)
        {
          puts ("fcntl failed");
          return 1;
        }
      if ((coe & FD_CLOEXEC) == 0)
        {
          printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
          return 1;
        }
    }
  close (fd[0]);
  close (fd[1]);

  puts ("OK");

  return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:28 -07:00
Ingo Molnar
9b610fda0d Merge branch 'linus' into timers/nohz 2008-07-18 19:53:16 +02:00
Thomas Gleixner
b8f8c3cf0a nohz: prevent tick stop outside of the idle loop
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:

	scheduler switch to idle task
	enable interrupts

Window starts here

	----> interrupt happens (does not set NEED_RESCHED)
	      	irq_exit() stops the tick

	----> interrupt happens (does set NEED_RESCHED)

	return from schedule()
	
	cpu_idle(): preempt_disable();

Window ends here

The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.

The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.

Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.

cpu_idle()
{
	preempt_disable();

	while(1) {
		 tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
		 			          are in the idle loop

		 while (!need_resched())
		       halt();

		 tick_nohz_restart_sched_tick(); <- disables NOHZ mode
		 preempt_enable_no_resched();
		 schedule();
		 preempt_disable();
	}
}

In hindsight we should have done this forever, but ... 

/me grabs a large brown paperbag.

Debugged-by: Jack Ren <jack.ren@marvell.com>, 
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-07-18 18:10:28 +02:00
Heiko Carstens
8b95d9172b fix core/stacktrace changes on avr32, mips, sh
Fixes this type of problem:

  CC      arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration

caused by "stacktrace: export save_stack_trace[_tsk]"

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-18 14:42:35 +02:00
Ingo Molnar
1a781a777b Merge branch 'generic-ipi' into generic-ipi-for-linus
Conflicts:

	arch/powerpc/Kconfig
	arch/s390/kernel/time.c
	arch/x86/kernel/apic_32.c
	arch/x86/kernel/cpu/perfctr-watchdog.c
	arch/x86/kernel/i8259_64.c
	arch/x86/kernel/ldt.c
	arch/x86/kernel/nmi_64.c
	arch/x86/kernel/smpboot.c
	arch/x86/xen/smp.c
	include/asm-x86/hw_irq_32.h
	include/asm-x86/hw_irq_64.h
	include/asm-x86/mach-default/irq_vectors.h
	include/asm-x86/mach-voyager/irq_vectors.h
	include/asm-x86/smp.h
	kernel/Makefile

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-15 21:55:59 +02:00
Linus Torvalds
af5329cdf5 Merge branch 'core/stacktrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/stacktrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  generic-ipi: powerpc/generic-ipi tree build failure
  stacktrace: fix build failure on sparc64
  stacktrace: export save_stack_trace[_tsk]
  stacktrace: fix modular build, export print_stack_trace and save_stack_trace
  backtrace: replace timer with tasklet + completions
  stacktrace: add saved stack traces to backtrace self-test
  stacktrace: print_stack_trace() cleanup
  debugging: make stacktrace independent from DEBUG_KERNEL
  stacktrace: don't crash on invalid stack trace structs
2008-07-15 10:31:35 -07:00
Ingo Molnar
7b4c9505f2 stacktrace: export save_stack_trace[_tsk]
Andrew Morton reported this against linux-next:

ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-03 09:17:55 +02:00
Jens Axboe
15c8b6c1aa on_each_cpu(): kill unused 'retry' parameter
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.

Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-06-26 11:24:38 +02:00
Jens Axboe
8691e5a8f6 smp_call_function: get rid of the unused nonatomic/retry argument
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.

Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-06-26 11:24:35 +02:00
Jens Axboe
490f5de52a sh: convert to generic helpers for IPI function calls
This converts sh to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single(). Not tested,
but it compiles.

Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-06-26 11:22:58 +02:00
Ingo Molnar
6d72b7952f Merge branch 'linus' into core/rodata 2008-06-16 11:24:00 +02:00