We are going to add more parameters to find_vqs, let's wrap the call so
we don't need to tweak all drivers every time.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On slave list updates, the bonding driver computes its hard_header_len
as the maximum of all enslaved devices's hard_header_len.
If the slave list is empty, e.g. on last enslaved device removal,
ETH_HLEN is used.
Since the bonding header_ops are set only when the first enslaved
device is attached, the above can lead to header_ops->create()
being called with the wrong skb headroom in place.
If bond0 is configured on top of ipoib devices, with the
following commands:
ifup bond0
for slave in $BOND_SLAVES_LIST; do
ip link set dev $slave nomaster
done
ping -c 1 <ip on bond0 subnet>
we will obtain a skb_under_panic() with a similar call trace:
skb_push+0x3d/0x40
push_pseudo_header+0x17/0x30 [ib_ipoib]
ipoib_hard_header+0x4e/0x80 [ib_ipoib]
arp_create+0x12f/0x220
arp_send_dst.part.19+0x28/0x50
arp_solicit+0x115/0x290
neigh_probe+0x4d/0x70
__neigh_event_send+0xa7/0x230
neigh_resolve_output+0x12e/0x1c0
ip_finish_output2+0x14b/0x390
ip_finish_output+0x136/0x1e0
ip_output+0x76/0xe0
ip_local_out+0x35/0x40
ip_send_skb+0x19/0x40
ip_push_pending_frames+0x33/0x40
raw_sendmsg+0x7d3/0xb50
inet_sendmsg+0x31/0xb0
sock_sendmsg+0x38/0x50
SYSC_sendto+0x102/0x190
SyS_sendto+0xe/0x10
do_syscall_64+0x67/0x180
entry_SYSCALL64_slow_path+0x25/0x25
This change addresses the issue avoiding updating the bonding device
hard_header_len when the slaves list become empty, forbidding to
shrink it below the value used by header_ops->create().
The bug is there since commit 54ef313714 ("[PATCH] bonding: Handle large
hard_header_len") but the panic can be triggered only since
commit fc791b6335 ("IB/ipoib: move back IB LL address into the hard
header").
Reported-by: Norbert P <noe@physik.uzh.ch>
Fixes: 54ef313714 ("[PATCH] bonding: Handle large hard_header_len")
Fixes: fc791b6335 ("IB/ipoib: move back IB LL address into the hard header")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren reports a kernel oops that resulted from my compile-time
fix on the default config. This shows two problems:
a) configurations that did not already enable PTP_1588_CLOCK will
now miss the cpts driver
b) when cpts support is disabled, the driver crashes. This is a
preexisting problem that we did not notice before my patch.
While the second problem is still being investigated, this modifies
the dependencies again, getting us back to the original state, with
another 'select NET_PTP_CLASSIFY' added in to avoid the original
link error we got, and the 'depends on POSIX_TIMERS' to hide
the CPTS support when turning it on would be useless.
Cc: stable@vger.kernel.org # 4.11 needs this
Fixes: 07fef36234 ("cpsw/netcp: cpts depends on posix_timers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call skb_cow_data, which is good anyway to ensure we can actually
modify the skb as such (another error from prior). Now that we have the
number of fragments required, we can safely allocate exactly that amount
of memory.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 99f81afc13.
It was papering over the real problem, which is fixed by commit
f555f34fdc ("net: phy: fix auto-negotiation stall due to unavailable
interrupt")
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.
The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.
During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.
Fixes: 321beec504 ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCBX app_data array is initialized with the incorrect values for
personality field. This would prevent offloaded protocols from
honoring the PFC.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My change (introduced in 4.11) to use find_first_clear_bit
incorrectly assumed that the size argument was words, not bits.
The effect was only a small limited number of the available send
sections were being actually used. This can cause performance loss
with some workloads.
Since map_words is now used only during initialization, it can
be on stack instead of in per-device data.
Fixes: b58a185801 ("netvsc: simplify get next send section")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In functions team_nl_send_port_list_get() and
team_nl_send_options_get(), pointer skb keeps the return value of
nlmsg_new(). When the call to genlmsg_put() fails, the memory is not
freed(). This will result in memory leak bugs.
Fixes: 9b00cf2d10 ("team: implement multipart netlink messages for options transfers")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlj/PI0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9ntrCADToD6OAE2/vEPgxrLFSEqEPS4vzXkL
6RObZRDYj0FrOo+Xkq9G8V+AKKJHH04CasQ0+XV0mCeVsx9GZTByllU8Sbej+sjO
SXlU9ZuhJGJEBCpFPqfjwGIxpCcRUF7BFxcBQgzOVY68m4fLHPMXSS0FS14r0B6M
GLk7nEGBUteYDDVCoWMNBt5VkIP6DXLfdvhTtj9R+BJmEwKZrXU3F6/Z5K686zf9
xAL01tn4rgLHhtWyxDTlVQ8CREZ+4YQAasi6usgLhNWTEpfCQaD22cyClM1pCV2s
HloB4DpOF507saJrmEz9n1BlnYXV1jqRkRHOB9UO0OvJR3Ta1XP5DOgp
=mnla
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.11-20170425' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-04-25
this is a pull request of three patches for net/master.
There are two patches by Stephane Grosjean for that add a new variant to the
PCAN-Chip USB driver. The other patch is by Maksim Salau, which swtiches the
memory for USB transfers from heap to stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: dd248f1bc6 ("sfc: Add PCI ID for Solarflare 8000 series 10/40G NIC")
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a parent macvlan device is destroyed we end up purging its
broadcast queue without dropping the device reference count on
the packet source device. This causes the source device to linger.
This patch drops that reference count.
Fixes: 260916dfb4 ("macvlan: Fix potential use-after free for...")
Reported-by: Joe Ghalam <Joe.Ghalam@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the PL-27A1 by adding the appropriate
USB ID's. This chip is used in the goobay Active USB 3.0 Data Link
and Unitek Y-3501 cables.
Signed-off-by: Roman Spychała <roed@onet.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.8
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a text line in the help section of the CAN_PEAK_USB
config item describing the support of the PCAN-USB X6 adapter, which is
already included in the Kernel since 4.9.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support of the PCAN-Chip USB, a stamp module for
customer hardware designs, which communicates via USB 2.0 with the
hardware. The integrated CAN controller supports the protocols CAN 2.0 A/B
as well as CAN FD. The physical CAN connection is determined by external
wiring. The Stamp module with its single-sided mounting and plated
half-holes is suitable for automatic assembly.
Note that the chip is equipped with the same logic than the PCAN-USB FD.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The 58xx devices (Northstar Plus) do actually have their CPU port wired
at port 8, it was unfortunately set to port 5 (B53_CPU_PORT_25) which is
incorrect, since that is the second possible management port.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the correct software reset sequence for 58xx devices by
setting all 3 reset bits and polling for the SW_RST bit to clear itself
without a given timeout. We cannot use is58xx() here because that would
also include the 7445/7278 Starfighter 2 which have their own driver
doing the reset earlier on due to the HW specific integration.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Broadcom tags are not enabled in b53 (DSA_PROTO_TAG_NONE), we need
to make sure that the IMP/CPU port is included in the forwarding
decision.
Without this change, switching between non-management ports would work,
but not between management ports and non-management ports thus breaking
the default state in which DSA switch are brought up.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+9NgAAoJEEg/ir3gV/o+/RIH/2Ua/FvxWtnaXhLj9GPELdGx
4Q2+ub43Q/F2cU2rIP0S/Ki3fEeOfk+IR87bvKBc+KTcLwUcBQloLjiLTxVOXSNY
+NmE7T1gl7Sb4NzJ9lDVYbmUlDzWZixbFkQdZ6nZJTKecXuN+xooL7EWosyZKuFd
FlDpIMacWlH2bMb/1U4lClg9MMPz8e37B9kJ0Vy/lert7NkVdXgYbPI2pKxweF9i
7yH0pNLKYvIQOubZZ9A7gPhk+OGp6xLAo9pJF6xG8tQuXI59Fz6tcKGbNb8GdzZu
g12EY2c75BxWJofPtvsDDM5i8ypwF3tfCqxDjw4h9F0wHGJv6tlh51vyuYA8ceg=
=KnUF
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-04-22
This series contains some mlx5 fixes for net.
For your convenience, the series doesn't introduce any conflict with
the ongoing net-next pull request.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5: E-Switch, Correctly deal with inline mode on ConnectX-5") kernels >= 4.10
("net/mlx5e: Fix ETHTOOL_GRXCLSRLALL handling") kernels >= 4.8
("net/mlx5e: Fix small packet threshold") kernels >= 4.7
("net/mlx5: Fix driver load bad flow when having fw initializing timeout") kernels >= 4.4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_put_padto() fails then it frees the skb. I shifted that code
up a bit to make my error handling a little simpler.
Fixes: a0d2f20650 ("Renesas Ethernet AVB PTP clock driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While this may appear as a humdrum one line change, it's actually quite
important. An sk_buff stores data in three places:
1. A linear chunk of allocated memory in skb->data. This is the easiest
one to work with, but it precludes using scatterdata since the memory
must be linear.
2. The array skb_shinfo(skb)->frags, which is of maximum length
MAX_SKB_FRAGS. This is nice for scattergather, since these fragments
can point to different pages.
3. skb_shinfo(skb)->frag_list, which is a pointer to another sk_buff,
which in turn can have data in either (1) or (2).
The first two are rather easy to deal with, since they're of a fixed
maximum length, while the third one is not, since there can be
potentially limitless chains of fragments. Fortunately dealing with
frag_list is opt-in for drivers, so drivers don't actually have to deal
with this mess. For whatever reason, macsec decided it wanted pain, and
so it explicitly specified NETIF_F_FRAGLIST.
Because dealing with (1), (2), and (3) is insane, most users of sk_buff
doing any sort of crypto or paging operation calls a convenient function
called skb_to_sgvec (which happens to be recursive if (3) is in use!).
This takes a sk_buff as input, and writes into its output pointer an
array of scattergather list items. Sometimes people like to declare a
fixed size scattergather list on the stack; othertimes people like to
allocate a fixed size scattergather list on the heap. However, if you're
doing it in a fixed-size fashion, you really shouldn't be using
NETIF_F_FRAGLIST too (unless you're also ensuring the sk_buff and its
frag_list children arent't shared and then you check the number of
fragments in total required.)
Macsec specifically does this:
size += sizeof(struct scatterlist) * (MAX_SKB_FRAGS + 1);
tmp = kmalloc(size, GFP_ATOMIC);
*sg = (struct scatterlist *)(tmp + sg_offset);
...
sg_init_table(sg, MAX_SKB_FRAGS + 1);
skb_to_sgvec(skb, sg, 0, skb->len);
Specifying MAX_SKB_FRAGS + 1 is the right answer usually, but not if you're
using NETIF_F_FRAGLIST, in which case the call to skb_to_sgvec will
overflow the heap, and disaster ensues.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereference "skb" to get "skb->len" so we should probably do that
step before freeing the skb.
Fixes: eea221ce48 ("tc35815 driver update (take 2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have observed a sudden spike in rx/tx_packets and rx/tx_bytes
reported under /proc/net/dev. There is a race in mlx5e_update_stats()
and some of the get-stats functions (the one that we hit is the
mlx5e_get_stats() which is called by ndo_get_stats64()).
In particular, the very first thing mlx5e_update_sw_counters()
does is 'memset(s, 0, sizeof(*s))'. For example, if mlx5e_get_stats()
is unlucky at one point, rx_bytes and rx_packets could be 0. One second
later, a normal (and much bigger than 0) value will be reported.
This patch is to use a 'struct mlx5e_sw_stats temp' to avoid
a direct memset zero on priv->stats.sw.
mlx5e_update_vport_counters() has a similar race. Hence, addressed
together. However, memset zero is removed instead because
it is not needed.
I am lucky enough to catch this 0-reset in rx multicast:
eth0: 41457665 76804 70 0 0 70 0 47085 15586634 87502 3 0 0 0 3 0
eth0: 41459860 76815 70 0 0 70 0 47094 15588376 87516 3 0 0 0 3 0
eth0: 41460577 76822 70 0 0 70 0 0 15589083 87521 3 0 0 0 3 0
eth0: 41463293 76838 70 0 0 70 0 47108 15595872 87538 3 0 0 0 3 0
eth0: 41463379 76839 70 0 0 70 0 47116 15596138 87539 3 0 0 0 3 0
v2: Remove memset zero from mlx5e_update_vport_counters()
v1: Use temp and memcpy
Fixes: 9218b44dcc ("net/mlx5e: Statistics handling refactoring")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handler for ETHTOOL_GRXCLSRLALL must set info->data to the size
of the table, regardless of the amount of entries in it.
Existing code does not do that, and this breaks all usage of ethtool -N
or -n without explicit location, with this error:
rmgr: Invalid RX class rules table size: Success
Set info->data to the table size.
Tested:
ethtool -n ens8
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1 loc 55
ethtool -n ens8
ethtool -N ens8 delete 1023
ethtool -N ens8 delete 55
Fixes: f913a72aa0 ("net/mlx5e: Add support to get ethtool flow rules")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
RX packet headers are meant to be contained in SKB linear part,
and chose a threshold of 128.
It turns out this is not enough, i.e. for IPv6 packet over VxLAN.
In this case, UDP/IPv4 needs 42 bytes, GENEVE header is 8 bytes,
and 86 bytes for TCP/IPv6. In total 136 bytes that is more than
current 128 bytes. In this case expand header flow is reached.
The warning in skb_try_coalesce() caused by a wrong truesize
was already fixed here:
commit 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()").
Still, we prefer to totally avoid the expand header flow for performance reasons.
Tested regular TCP_STREAM with iperf for 1 and 8 streams, no degradation was found.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When UAR is released, we deallocate the device resource, but
don't unmmap the UAR mapping memory.
Fix the leak by unmapping this memory.
Fixes: a6d51b6861 ('net/mlx5: Introduce blue flame register allocator)
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv6 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv4 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On ConnectX5 the wqe inline mode is "none" and hence the FW
reports MLX5_CAP_INLINE_MODE_NOT_REQUIRED.
Fix our devlink callbacks to deal with that on get and set.
Also fix the tc flow parsing code not to fail anything when
inline isn't required.
Fixes: bffaa91658 ('net/mlx5: E-Switch, Add control for inline mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If FW is stuck in initializing state we will skip the driver load, but
current error handling flow doesn't clean previously allocated command
interface resources.
Fixes: e3297246c2 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We can use skb_cow_head() to properly deal with clones,
especially the ones coming from TCP stack that allow their head being
modified. This avoids a copy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: 4a476bd6d1 ("usbnet: New driver for QinHeng CH9200 devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: cc28a20e77 ("introduce cx82310_eth: Conexant CX82310-based ADSL router USB ethernet driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ieee_setpfc() callback implementation to populate traffic class
count with the user provided value.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_dcbnl_get_dcbx() API uses kmalloc in GFT_KERNEL mode. The API gets
invoked in the interrupt context by qed_dcbnl_getdcbx callback. Need
to invoke this kmalloc in atomic mode.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PFC error-mask value is not supported by MFW, but this bit could be
set in the pfc bit-map of the operational parameters if remote device
supports it. These operational parameters are used as basis for
populating the dcbx config parameters. User provided configs will be
applied on top of these parameters and then send them to MFW when
requested. Driver need to clear the error-mask bit before sending the
config parameters to MFW.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some adapters may not publish the max_tc value. Populate the default
value for max_tc field in case the mfw didn't provide one.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was failing to check that the SKB wasn't cloned
before adding checksum data.
Replace existing handling to extend/copy the header buffer
with skb_cow_head.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is prompted by a static checker warning about a potential
use after free. The concern is that netif_rx_ni() can free "skb" and we
call it twice.
When I look at the commit that added this, it looks like some stray
lines were added accidentally. It doesn't make sense to me that we
would recieve the same data two times. I asked the author but never
recieved a response.
I can't test this code, but I'm pretty sure my patch is correct.
Fixes: 4b063258ab ("dp83640: Delay scheduled work.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA API debugging (when enabled) causes:
WARNING: CPU: 0 PID: 1445 at lib/dma-debug.c:519 add_dma_entry+0xe0/0x12c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x01b2974d
to be printed after repeated initialization of the Ether device, e.g.
suspend/resume or 'ifconfig' up/down. This is because DMA buffers mapped
using dma_map_single() in sh_eth_ring_format() and sh_eth_start_xmit() are
never unmapped. Resolve this problem by unmapping the buffers when freeing
the descriptor rings; in order to do it right, we'd have to add an extra
parameter to sh_eth_txfree() (we rename this function to sh_eth_tx_free(),
while at it).
Based on the commit a47b70ea86 ("ravb: unmap descriptors when freeing
rings").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix port inconsistency on TXD due to hardware BUG that would cause
different port number is carried on the same TXD between tx_map()
and tx_unmap() with the iperf test. It would cause confusing BQL
logic which leads to kernel panic when dual GMAC runs concurrently.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inconsistency between the TXD descriptor and the used buffer that
would cause unexpected logic at mtk_tx_unmap() during skb housekeeping.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the command:
ethtool --phy-statistics eth0
will cause system crash with meassage "Unable to handle kernel NULL pointer
dereference at virtual address 00000010" from:
(kszphy_get_stats) from [<c069f1d8>] (ethtool_get_phy_stats+0xd8/0x210)
(ethtool_get_phy_stats) from [<c06a0738>] (dev_ethtool+0x5b8/0x228c)
(dev_ethtool) from [<c06b5484>] (dev_ioctl+0x3fc/0x964)
(dev_ioctl) from [<c0679f7c>] (sock_ioctl+0x170/0x2c0)
(sock_ioctl) from [<c02419d4>] (do_vfs_ioctl+0xa8/0x95c)
(do_vfs_ioctl) from [<c02422c4>] (SyS_ioctl+0x3c/0x64)
(SyS_ioctl) from [<c0107d60>] (ret_fast_syscall+0x0/0x44)
The reason: phy_driver structure for KSZ9031 phy has no .probe() callback
defined. As result, struct phy_device *phydev->priv pointer will not be
initializes (null).
This issue will affect also following phys:
KSZ8795, KSZ886X, KSZ8873MLL, KSZ9031, KSZ9021, KSZ8061, KS8737
Fix it by:
- adding .probe() = kszphy_probe() callback to KSZ9031, KSZ9021
phys. The kszphy_probe() can be re-used as it doesn't do any phy specific
settings.
- removing statistic callbacks from other phys (KSZ8795, KSZ886X,
KSZ8873MLL, KSZ8061, KS8737) as they doesn't have corresponding
statistic counters.
Fixes: 2b2427d064 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
