There's only one place using this function, so
move it where it's needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be doing a shift (1 << FLAG_RADIO_DOWN) here before testing
the flag. As luck would have it, this test works almost correctly.
The current code tests for FLAG_RADIO_OFF instead of FLAG_RADIO_DOWN.
#define FLAG_RADIO_OFF 0 /* User disabling of MAC */
#define FLAG_RADIO_DOWN 1 /* ifup/ifdown disabling of MAC */
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we only monitor while associated, the following
can happen:
- we're associated, and the queue stuck check
runs, setting the queue "touch" time to X
- we disassociate, stopping the monitoring,
which leaves the time set to X
- almost 2s later, we associate, and enqueue
a frame
- before the frame is transmitted, we monitor
for stuck queues, and find the time set to
X, although it is now later than X + 2000ms,
so we decide that the queue is stuck and
erroneously restart the device
It happens more with P2P because there we can
go between associated/unassociated frequently.
Cc: stable@vger.kernel.org
Reported-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192ce when used with the RTL8188CE device would start at about
20 Mbps on a 54 Mbps connection, but quickly drop to 1 Mbps. One of the
symptoms is that the AP would need to retransmit each packet 4 of 5 times
before the driver would acknowledge it. Recovery is possible only by
unloading and reloading the driver. This problem was reported at
https://bugzilla.redhat.com/show_bug.cgi?id=770207.
The problem is due to a missing update of the gain setting.
Signed-off-by: Jingjun Wu <jingjun_wu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the possibility of having the mesh point and AP to be operated
simultaneously in one single radio. Previously, mesh point fails to generate the
mesh beacon if virtual AP is created for the same radio.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tidying up some debug statements in brcms_c_ampdu_dotxstatus_complete()
that got broken strings to satisfy checkpatch, but the rules changed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As indicated in [1] on netdev mailing list drivers should not block
on the init_module() syscall. This patch defers the actual driver
registration to a workqueue so the init_module() syscall can complete
without delay.
[1] http://article.gmane.org/gmane.linux.network/217729/
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As indicated in [1] on netdev mailing list drivers should not block
on the init_module() syscall. This patch defers the actual driver
registration to a workqueue so the init_module() syscall can complete
without delay.
[1] http://article.gmane.org/gmane.linux.network/217729/
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module init function of brcmfmac calls init functions for SDIO and
USB doing driver registration. This patch removes terminating the module
init when a driver registration for one host interface fails.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb code defines a structure for counting statistics. However,
it should use the statistics entry provided in brcmf_bus as that is
exposed to the net_device. The usb private statistics counter only
remains with counters for control packets between driver and usb
device.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several fields in this structure are only written once or not used
at all. Remaining two fields have been moved and brcmf_usb_attrib
definition has been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_usb_up() the variable devinfo was checked for being
a NULL pointer, but this can not happen. Also the check was done
after dereferencing the pointer. This patch removes the check.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver rtl8192cu is used with the debug level set to 3 or greater,
the result is "sleeping function called from invalid context" due to
an rcu_read_lock() call in the DM refresh routine in driver rtl8192c.
This lock is not necessary as the USB driver does not use the struct
being protected, thus the lock is set only when a PCI interface is
active.
This bug is reported in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In usb.c, routine _rtl_usb_init_sw() always returns 0, and rtl_usb_probe()
never checks the returned value. Thus we can change _rtl_usb_init_sw() to
a void routine. In addition, remove the underscore at the beginning of the
name of the routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the unlikely event of a misread of the USB end point count, the driver
generates a divide fault. To prevent this, add a check of the value
returned by _rtl_usb_init(). In addition, add some logging to indicate
why the condition occurred.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mwifiex_drv_change_adhoc_chan() we pass channel to
mwifiex_bss_ioctl_ibss_channel() which sets the high 16 bits. This
works on little endian systems but not on big endian ones. I've changed
mwifiex_drv_change_adhoc_chan() to use a 16 bit variable. This matches
the other functions in the file.
I considered changing mwifiex_change_adhoc_chan() as well but it turns
out that the function isn't implemented so I just removed the
definition.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible to reload driver if insmod has failed due to
missing firmware.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 uses u8 for key indexes and so should rndis_wlan.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use new RNDIS_WLAN_NUM_KEYS for checks in add_wep_key() and add_wpa_key().
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'beacon_period' in 'struct ndis_80211_conf' is __le32 instead of __le16 so
le32_to_cpu must be used instead of le16_to_cpu.
Also correct 'beacon_interval' variables used for passing this value forward
from u16 to u32 and rename those variables 'beacon_period' This is to avoid
confusion because 'beacon_interval' is defined as __le16 at other structure,
'struct ndis_80211_fixed_ies'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we pick a high value for "offset" then it could lead to an integer
overflow and we would get past the check for:
if (offset + len > buflen) { ...
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These variables can never be less than zero because we cap them in
get_device_pmkids(). Let's make them unsigned here because it's simpler
to not have to worry about negative numbers when we read the code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use the "len" variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If "offset" is negative then we can get past this check:
if (offset > CONTROL_BUFFER_SIZE)
Or if we pick a very high "req_ie_len" then we can get around the check:
if (offset + req_ie_len > CONTROL_BUFFER_SIZE)
I made "resp_ie_len" and "req_ie_len" unsigned. I don't know if it was
intentional that they were signed in the original.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the bcm5354 (Soc with integrated LP-PHY Wifi) with a recent
firmware >= 478.104 it runs out of memory after a very short time in
OpenWrt after doing an active scan or any thing else where packages are
send. This was cased by a gpio misconfiguration, the firmware triggered
the GPIO pins used for buttons on some devices and that caused an other
driver (OpenWrt diag) listening for these buttons irqs to send many
messages to the user space.
This patch fixes the bug for my devices (Asus WL-520GU) and makes it
work with firmware 666.2. Now the firmware just uses LED GPIO pin
number 1 and not the button pins any more.
This is the GPIO Pin layout used on my device, see [0].
GPIO pin layout:
pin# name type
0 power led
1 wlan led
2 reset button
3 ses buttom
This is the nvram configuration output of "nvram show |grep gpio"
related nvram configuration:
wl0gpio2=11
wl0gpio3=11
wl0gpio0=11
wl0gpio1=0x02
reset_gpio=2
[0]: https://dev.openwrt.org/browser/trunk/package/broadcom-diag/src/diag.c
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this does the same thing as the previous code
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
its better to zero initialize the 'valid_phy_rate_idx' array completely
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently if valid SSID list is provided in scan request, driver
performs specific SSID scan otherwise wildcard scan is chosen.
When wpa_supplicant provides valid SSID list followed by
zero-length SSID for wildcard scan, only specific SSID scan is
performed by driver. Actually driver is expected to do both type
of scanning in this case. The patch fixes this issue.
Also, use SSID list pointer provided by stack directly, instead
of copying SSID's to local structure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use struct cfg80211_ssid available in include/net/cfg80211.h
instead of having similar definition in driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Driver and firmware do not support 22Mbps and 72Mbps bitrates.
Remove them from the rate table advertised to cfg80211.
2. First 4 rates from mwifiex_rates table are not valid for
5GHz/A band. Set correct bitrate array's index and no of rates for
ieee80211_supported_band for 5GHz band.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so could cause the tx status queue to overflow during longer
periods of time without non-beacon tx. These events are also required
for proper drv_tx_last_beacon handling.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9003 uses a global tx status queue, processing tx status outside of
the regular tx tasklet is dangerous and messes up hardware/software
synchronization of tx status events.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The approach of this change is flawed, as it triggers tx status processing
from more callsites, yet the chips only have one global tx status queue.
Subsequent patches will properly fix the issue that this one tried to address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When authentication type is configured to NL80211_AUTHTYPE_AUTOMATIC,
driver tries to connect using open mode. The association is failed
if AP is configured in shared mode.
This patch adds code to try association using shared mode as well if
open mode association fails.
Now since we returned exact error code in association response handler
(instead of -1), corresponding changes are done in
mwifiex_process_cmdresp().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That commit intended for 3.4 renamed IEEE80211_TX_CTL_POLL_RESPONSE as
IEEE80211_TX_CTL_NO_PS_BUFFER. Meanwhile, "carl9170: fix frame delivery
if sta is in powersave mode" added a reference to
IEEE80211_TX_CTL_POLL_RESPONSE in the fixes stream for 3.3. This simple
patch fixes that merge boo-boo.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous RX error checking was done exclusive-or for different error
types and caused DFS pulse events to be dropped when other error
flags (e.g. CRC) were set simultaneously.
This patch decouples PHY error processing from other types and ensures
that all pulses detected by HW are accounted by the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the enum il4965_calib_enabled_state because it is not used.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the enum il_calib. It defined one identifier: IL_CALIB_MAX.
Remove the function il4965_calib_free_results. It was doing nothing
because IL_CALIB_MAX is zero. Next, remove calib_results from the
il_priv structure and also remove the associated return
type/struct il_calib_result.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the menuconfig system doesn't indent the debug options
for the 3945 /4965, add some text to make it clear which
debug options are being configured.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the debug options so they appear below the 3945 / 4965 options.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of defining an 'enum', we can simply use 'u8' flag for WEP
status. Rename 'wep_status' to 'wep_enabled' to match with
'wpa_enabled' and 'wpa2_enabled'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It should have been removed by commit "mwifiex: use cfg80211 dynamic
scan..." (7c6fa2a843..) after adding code to avoid an extra scan
during association because scan entries are valid for 15 seconds in
cfg80211 stack.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's just a duplicate of ipw2100_bg_rates[].
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
