The ESP8089 chips can mostly be enumerated via their sdio interface,
but they are clocked by an external crystal which may differ from one
board to the other.
This commit adds a binding for the sdio child node for these chips,
allowing to specify the external crystal type (for now, this binding
could be be extended with e.g. OOB irq support later).
The Android driver for this chip uses a text file with key,value pairs
which gets loaded as firmware to pass this info to the firmware.
The "esp,crystal_26M_en" name is chosen to match the crystal_26M_en
key-name in that text file.
Note that at this point there only is an out of tree driver for this
hardware, there is no clear timeline / path for merging this. Still
I believe it would be good to specify the binding for this in tree
now, so that any future migration to an in tree driver will not cause
compatiblity issues.
Cc: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add support for using with both wl12xx and wl18xx.
- all wilink family needs special init command for entering wspi mode.
extra clock cycles should be sent after the spi init command while the
cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
completes the init stage.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add device tree binding documentation for MARVELL's sd8xxx
(sd8897 and sd8997) wlan chip.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There two things done in this patch,
1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
not only calibration data, it carries board specific data too.
So, make appropriate update in doc.
2) ipq4019 wifi needs new devie tree entry to carry calibration
data alone (called pre cal data, it doesn't include any other info).
Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
the purpose of it. Hence, add new device tree entry called
'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.6. Major changes:
ath10k
* dt: add bindings for ipq4019 wifi block
* start adding support for qca4019 chip
ath9k
* add device ID for Toshiba WLM-20U2/GN-1080
* allow more than one interface on DFS channels
Add DT support for the wl1271 SPI WiFi.
Add documentation file for the wl1271 SPI WiFi.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add device tree binding documentation details for wifi block present
in Qualcomm IPQ4019 SoC into "qcom,ath10k.txt".
Right now, ath10k wireless driver has support for PCI based wlan devices.
There is a plan to extend ath10k driver to support wifi devices which are
connected over AHB as well (enumeration will happen via device tree node).
For AHB based devices (ie, ipq4019), all wifi properties are supplied via
device tree (including irq, reg addr, cal data,etc).
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Rob Herring <robh@kernel.org>
[kvalo@qca.qualcomm.com: fixed typos noticed by Rob]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add device tree binding documentation for TI's wilink
(wl12xx and wl18xx) wlan chip.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Broadcom bcm43xx sdio devices are fullmac devices that may be
integrated in ARM platforms. Currently, the brcmfmac driver for
these devices support use of platform data. This patch specifies
the bindings that allow this platform data to be expressed in the
devicetree.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[hdegoede@redhat.com: drop clk / reg_on gpio handling, as there is no consensus
on how to handle this yet]
[hdegoede@redhat.com: move from bindings/staging to bindings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add device tree binding documentation for Texas Instrument's wl1251
wireless lan chip. For now only the SPI binding is documented.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
