be consistent with mac80211 drivers and return correct return code.
NETDEV_TX_OK is 0, but we need to be consistent wrt formatting amongst
implementations
re: http://marc.info/?l=linux-wireless&m=123119327419865&w=2
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Giuseppe Cala <jiveaxe@gmail.com> (The second "a" in "Cala" should be
a grave, U+00E0) reported success on zd1211-devs@lists.sourceforge.net.
The chip info is:
zd1211b chip 0df6:0036 v4810 high 00-0c-f6 AL2230_RF pa0 g--N-
The Sitecom WL-603 is detected as a zd1211b with a AL2230 RF transceiver chip.
Signed-off-by: Giuseppe Cala <jiveaxe@gmail.com>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In theory, the firmware acks the received a data frame, before signaling the driver to free it again.
However Artur Skawina <art.08.09@gmail.com> has shown that it can happen in reverse order as well.
This is very bad and could lead to memory corruptions, oopses and panics.
Thanks to Artur Skawina <art.08.09@gmail.com> for reporting and debugging this issue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we let the firmware do the data encryption, we have to remove the ICV and
(M)MIC at the end of the frame before we can give it back to mac80211.
Or, these data frames have a few trailing bytes on cooked monitor interfaces.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a obvious memory leak in the eeprom parser.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
KERN_INFO is too "loud" for messages that are generated by the ordinary
events, such as accociation. Use of KERN_DEBUG is consistent with
mac80211.
Suggested by Michael Gilbert <michael.s.gilbert@gmail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 provides 2 structures to handle bitrates, namely
ieee80211_rate and ieee80211_tx_rate. To determine the short preamble
mode for an outgoing frame, the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE
must be checked on ieee80211_tx_rate and not ieee80211_rate (which rt2x00 did).
This fixes a regression which was triggered in 2.6.29-rcX as reported by Chris Clayton.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-By: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mcs7830_set_reg() and mcs7830_get_reg() are called with buffers
from stack which must not be used directly for USB transfers.
This causes corruption of the stack particulary on non x86
architectures because DMA may be used for these transfers.
Signed-off-by: Christian Eggers <christian.eggers@kathrein.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve usbnet's devdbg to always type-check diagnostic arguments,
like dev_dbg (device.h). This makes no change to the resulting size of
usbnet modules.
This patch also removes an #ifdef DEBUG directive from rndis_wlan so
it's devdbg statements are always type-checked at compile time.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
while(--j >= 0) keeps spinning when j is unsigned:
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't forget to call pci_disable_device() in myri10ge_remove()
and when myri10ge_probe() fails.
By the way, update the copyright years.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.
However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.
Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to what the docs say, the 'extended interrupt cause' bit in
the interrupt cause register (bit 1) appears to not be maskable on at
least some of the mv643xx_eth platforms, making writing zeroes to the
interrupt mask register but not the extended interrupt mask register
insufficient to stop interrupts from occuring. Therefore, also write
zeroes to the extended interrupt mask register when shutting down the
port.
This fixes the interrupt storm seen on the Pegasos board when shutting
down the interface.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 66e63ffbc0 ("mv643xx_eth:
implement ->set_rx_mode()") cleaned up mv643xx_eth's multicast filter
programming, but broke it as well.
The non-special multicast filter table (for multicast addresses that
are not of the form 01:00:5e:00:00:xx) consists of 256 hash table
buckets organised as 64 32-bit words, where the 'accept' bits are
in the LSB of each byte, so in bits 24 16 8 0 of each 32-bit word.
The old code got this right, but the referenced commit broke this by
using bits 3 2 1 0 instead. This commit fixes this up.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cd4ccf76bf.
On the Pegasos board, we can't do DMA burst that are longer than
one cache line. For now, go back to using 32 byte DMA bursts for
all mv643xx_eth platforms -- we can switch the ARM-based platforms
back to doing long 128 byte bursts in the next development cycle.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reported-by: Alan Curry <pacman@kosh.dhis.org>
Reported-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies how the tg3 driver handles device firmware.
The patch starts by consolidating David Woodhouse's earlier patch under
the same name. Specifically, the patch moves the request_firmware call
into a separate tg3_request_firmware() function and calls that function
from tg3_open() rather than tg3_init_one().
The patch then goes on to limit the number of devices that will make
request_firmware calls. The original firmware patch unnecessarily
requested TSO firmware for devices that did not need it. This patch
reduces the set of devices making TSO firmware patches to approximately
the following device set : 5703, 5704, and 5705.
Finally, the patch reduces the effects of a request_firmware() failure.
For those devices that are requesting TSO firmware, the driver will turn
off the TSO capability. If TSO firmware becomes available at a later
time, the device can be closed and then opened again to reacquire the
TSO capability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid. The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints. This patch forces RO not to be set for
descriptors as well as payload. This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the assigned value is being overwritten shortly after, it can be
dropped and so the whole variable definition moved to the start of the
function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is copy and paste from the original driver. As skb_reserve() is
also called within korina_alloc_ring() when initially allocating the
receive descriptors, the same should be done when allocating new space
after passing an skb to upper layers.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last loop iteration, i has the value RC32434_NUM_RDS and
therefore leads to an index overflow when used afterwards to address the
last element. This is yet another another bug introduced when rewriting
parts of the driver for upstream preparation, as the original driver
used 'RC32434_NUM_RDS - 1' instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lro manager's frag_align_pad setting was missing,
leading to misaligned access to the skb passed up
to the stack.
Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases when an underrun occur, all macb buffers where consumed
and the netif_queue was stopped infinitely. This happens then the TGO
(transfer ongoing) bit in the TSR is set (and UND). It seems like
clening up after the underrun makes the driver and the macb hardware
end up in an inconsistent state. The result of this is that in the
following calls to macb_tx no TX buffers are released -> the
netif_queue was stopped, and never woken up again.
The solution is to disable the transmitter, if TGO is set, before
clening up after the underrun, and re-enable the transmitter when the
cleaning up is done.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the version and the year of updated files
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make sure no swapping are made by the compiler, changed HAS_WORK to inline
functions and added all the necessary barriers
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Driver supports the 57711 and 57711E as well but the description was out of
date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the default PHY version (0x4321) is read - the PHY FW load failed
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10M/100M autoneg was not establishing link.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting loopback requires time to take effect
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW should be configured so fast toggling between 1G and 10G will not be
missed. Make sure that the HW is re-configured in full
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the page size is > 8KB this violation happens
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't dump eeprom when bnx2x adapter is down. Running ethtool -e causes an eeh
without it when the device is down
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Has a negative side effect when sending MAC update with no content (as done in
the self-test)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lock was release too soon. Make sure the HW is marked as locked until the
boot driver was unloaded from FW perspective
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failures in the probe not handled correctly - separate the flow to handle
different failures
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error check could result with not freeing the IRQ
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Use consistent types for ehca_plpar_hcall9()
IB/ehca: Fix printk format warnings from u64 type change
IPoIB: Do not print error messages for multicast join retries
IB/mlx4: Fix memory ordering problem when posting LSO sends
mlx4_core: Fix min() warning
IPoIB: Fix deadlock between ipoib_open() and child interface create
IPoIB: Fix hang in napi_disable() if P_Key is never found
p54 doesn't support AES-128-CMAC offload.
This patch will fix the noisy mac80211 warnings, when 802.11w is enabled:
mac80211-phy189: failed to set key (4, ff:ff:ff:ff:ff:ff) to hardware (-22)
mac80211-phy189: failed to set key (5, ff:ff:ff:ff:ff:ff) to hardware (-22)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running modprobe rt73usb, and then rmmod rt73usb, and then
iwconfig, the wlan0 device does not disappear. When repeating this
process again, we get a kernel Oops errors and "BUG: unable to handle
kernel paging request..." message in the kernel log.
The reason for this is that there is an error in rt2x00rfkill_free(),
which is called in the process of removing the device
(rt2x00lib_remove_dev() in rt2x00dev.c).
rt2x00rfkill_free() clears the RFKILL_STATE_ALLOCATED bit , which is
bit number 1 () in rt2x00dev->flags instead of in
rt2x00dev->rfkill_state. As a result, when checking the
DEVICE_STATE_REGISTERED_HW bit (bit number 1 in rt2x00dev->flags) in
rt2x00lib_remove_hw() it is **unset**, and we wrongly **don't** call
ieee80211_unregister_hw().
This patch corrects this: the parameter for __test_and_clear_bit() in
rt2x00rfkill_free() should be &rt2x00dev->rfkill_state and not
&rt2x00dev->flags.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function iwl_send_cmd_sync(), if the flag CMD_WANT_SKB is set but
we are not provided with a valid SKB (cmd->meta.u.skb == NULL), we need
to remove the CMD_WANT_SKB flag from the TX cmd queue. Otherwise in case
the cmd comes in later, it will possibly set an invalid address. Thus
it causes an invalid memory access.
This fixed the bug http://bugzilla.kernel.org/show_bug.cgi?id=11326.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect operator causes the REG_DOMAIN_2GHZ_MASK to be zero which
surely was not the goal of this definition. Mask out the 11a flags
correctly.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was not supposed to be a bitwise AND operation, but a check of
two separate conditions. Anyway, the old code happened to result in
the same behavior, so this is just changing the code to be easier to
understand and also to keep sparse from warning about dubious
operators.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Data structures that come over the wire from the WLAN firmware must be packed.
This fixes alignment problems on the blackfin architecture and, reportedly, on
the AVR32.
This is a replacement for the previous version of this patch which had also
explicitly used get_unaligned_ macros. As Johannes Berg pointed out, these
macros were unnecessary.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug that could occur, if it the eeprom is incomplete or partly corrupted.
BUG: unable to handle kernel NULL pointer dereference at 00000008
IP: p54_assign_address+0x108/0x15d [p54common]
Oops: 0002 [#1] SMP
Pid: 12988, comm: phy1 Tainted: P W 2.6.28-rc6-wl #3
RIP: 0010: p54_assign_address+0x108/0x15d [p54common]
[...]
Call Trace:
p54_alloc_skb+0xa3/0xc0 [p54common]
p54_scan+0x37/0x204 [p54common]
[...]
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a build error in absence of CONFIG_IPV6:
drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.
"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix
drivers/net/mlx4/profile.c: In function `mlx4_make_profile':
drivers/net/mlx4/profile.c:110: warning: comparison of distinct pointer types lacks a cast
This happened because num_possible_cpus() was secretly changed by
commit ae7a47e7 ("cpumask: make cpumask.h eat its own dogfood.") from
returning "int" to (now) returning "unsigned int". I think that was a
good change, so we should just swallow the fallout.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Cc: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: Vladimir Sokolovsky <vlad@mellanox.co.il>
Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
b44 chip has some hardware limitations, that need GFP_DMA bounce
buffers in some situations.
In order to not deplete DMA zone, we should keep allocated GFP_DMA skb
only for driver use. At rx time, we copy such skb to newly allocated
skb, reusing existing copybreak infrastructure.
On machines with low amount of memory, all skb meet the hardware limitation,
so no copy is needed. We detect this situation using a new device flag, set
to one if one GFP_DMA skb was ever allocated by b44_alloc_rx_skb().
Previously allocated skb, even outside from DMA zone will then be recycled,
to have minimal impact on DMA zone use.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Ionut Leonte <ionut.leonte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is for Alan Cox as it related to the tty layer.
Hopefully the hso driver is again relatively stable with this fix.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HSO changes for kref introduced a recursive spinlock take. All
functions which call put_rxbuf_data already have serial->serial_lock
grabbed.
[Comment to code added-AC]
Signed-off-by: Denis Joseph Barrow <D.Barrow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the kernel warning states: "IRQF_DISABLED is not guaranteed on shared
IRQs". Since these IRQs' values are hardcoded and my test system doesn't
show any shared use of IRQs at all, rather make them non-shared than
non-disabled.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently this doesn't make sense. Otherwise the queue gets disabled as
soon as it's getting empty and can only be resurrected by a driver
restart.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally this must have been a rewrite error when introducing
'chain_index'. But the original driver did not use the previous chain
item everywhere: when altering the address tx_chain_tail points to, it
should move forward, not backwards.
Also this is not an "index" but rather the penultimate element in the
chain, so rename it accordingly.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Triggering TX before the write to the DMA status mask register leads to
transferring packets with maximum payload no matter what the actual
packet size is.
While here, also trigger RX scheduling after writing the DMA status mask
register, like it was in the original driver before it was sent
upstream.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The called netif_rx_schedule() does all the work for us:
- it checks the return value of netif_rx_schedule_prep() and
- if everything is ok calls __netif_rx_schedule().
Before this change, the driver received absolutely nothing.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function needs an early exit condition to function properly, or
else caller assumes napi workload wasn't enough to handle all received
packets and korina_rx is called again (and again and again and ...).
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this the driver will crash when the NIC is being restarted.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new value is the one used in the external patch before and allows at
least a standard MTU of 1500 to be handled correctly. Impact of this
change gets visible when bigger packets are to be received, issuing:
| ping -s 492 <IP>
and bigger payload sized led to 100% packet loss.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Using platform_set_drvdata() here makes no sense, since the driver_data
field has already been filled with valuable data (i.e. the MAC address).
Also having driver_data point to the net_device is rather pointless
since struct korina_device contains an apropriate field for it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "read for interrupts" flag must be set before enabling slow-path
interrupts as well (and not just before fast-path interrupts)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too big packets could pass due to wrong filter size
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong initialization of the multi-queue indirection table - it should
be using the function and not the port index
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the doorbell is 4KB, this bug become visible when using
more than 8 queues
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding missing le_to_cpu and disabling wrong HW endianity flag (the
two complete each other)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong handling of tagged packet if VLAN offload is disabled caused
packets to get corrupted
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this lock, in some race conditions the driver missed link
change indication
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the page size is not 4KB, the FW must be programmed to work with
the right SGE boundaries and fragment list length.
To avoid confusion with the BCM_PAGE_SIZE which is set to 4KB for the
FW sake, another alias for the system page size was added to
explicitly indicate that it is meant for the SGE
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on IA64, it became clear that the following memory
barriers are missing
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since slow-path events, including link update, are handled in
work-queue, a race condition was introduced in the self-test that
sometimes caused the link status to fail: the self-test was running
under RTNL lock, and if the link-watch was scheduled it stoped the
shared work-queue (waiting for the RTNL lock) and so the link update
event was not handled until the self-test ended (releasing the RTNL
lock) with failure (since the link status was not updated)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch hooks up the start_xmit/tx_timeout/get_stats callbacks
in the ax88796 driver since they no longer are installed by the
lib8390 code. Without this patch the function dev_hard_start_xmit()
crashes due to a start_xmit callback with the value NULL.
While at it, update the ax88796 driver to make use of use of struct
net_device_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an init_dummy_netdev() function that gets a network device
structure (allocation and lifetime entirely under caller's control) and
initialize the minimum amount of fields so it can be used to schedule
NAPI polls without registering a full blown interface. This is to be
used by drivers that need to tie several hardware interfaces to a single
NAPI poll scheduler due to HW limitations.
It also updates the ibm_newemac driver to use that, this fixing the
oops on 2.6.29 due to passing NULL as "dev" to netif_napi_add()
Symbol is exported GPL only a I don't think we want binary drivers doing
that sort of acrobatics (if we want them at all).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=12397
We're doing an sprintf of an 11-char string into an 11-char buffer.
Whoops. It breaks firmware uploading.
Reported-by: Jos-Vicente Gilabert <josevteg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Bail out if pci_map_single() fails while replenishing rx ring.
o Drop packet if pci_map_{single,page}() fail in tx.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware commands like mac address addition/deletion are sent
on the transmit ring. So need to hold the tx lock before touching
tx producer/consumer indices.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a tiny memory leak when driver is unloaded. The mac
address list maintained in netxen_adapter needs to deleted when
driver is going down.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix order or rom register writes.
o Reduce udelays when writing rom registers.
This cuts the firmware init time by 40%.
o Do not reset core/memory clocks when reinitializing driver.
Firmware willl handle this when initialized.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Read negotiated link speed when link state changes.
o Fix link speed reporting for hybrid nic boards, which have both 1Gbps and
10Gbps ports.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o fix the ip/tcp hdr offset in tx descriptors for ipv6.
o cleanup xmit function, move the tso checks into separate function,
this reduces unnecessary endian conversions back and forth.
o optimize macros to initialize tx descriptors.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set restricted (little endian) data types in firmware command
requests and responses.
o Remove unnecessary conversion to LE when writing registers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attached patch modifies the sis900 driver when the MAC address
read from the hardware is invalid. As suggested, the patch now
generates a random address so that the user can go on and use
the hardware. In any case a message is also shown to warn on the
unexpected condition.
This seems to happen with newer HW implementation of the sis900
chipset, since this never came up before.
Patch is against vanilla 2.6.28 (but the driver doesn't change so often,
so it will probably apply to older/newer versions too).
See bugzilla ID 10201 and 11649 and ignore the previous patch.
Signed-off-by: Daniele Venzano <venza@brownhat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If something goes wrong attaching to phy driver, we weren't freeing
the IRQ.
Signed-off-by: Mike Ditto <mditto@consentry.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (29 commits)
powerpc/83xx: Move mcu_mpc8349emitx driver out of drivers/i2c/chips/
powerpc/83xx: Make serial ports work on MPC8315E-RDB w/ FSL U-Boots
powerpc/e500mc: Doorbells need to be taken w/exceptions disabled
powerpc: Enable PS3 options and QPACE in ppc64_defconfig
powerpc/powermac: Fix occasional SMP boot failure
powerpc/cacheinfo: Rename cache_dir per-cpu variable
hvc_console: Use kzalloc() instead of kmalloc() + memset()
hvc_console: Do not set low_latency when using interrupts
hvc_console: Call free_irq() only if request_irq() was successful
hvc_console: Change an mb() to smp_mb() and add some comments
powerpc: Cleanup from l64 to ll64 change: drivers/net
powerpc: Cleanup from l64 to ll64 change: drivers/char
powerpc: Cleanup from l64 to ll64 change: arch code
powerpc: Change u64/s64 to a long long integer type
powerpc/kexec: Check crash_base for relocatable kernel
powerpc: Make dummy section a valid note header
Xilinx: SPI: updated driver for device tree
drivers/of: Add the of_find_i2c_device_by_node function.
powerpc/xsysace: add compatible string for non-ipcore instance
powerpc/mpc52xx: remove dead code from GPIO driver
...
Freescale on-chip TBI PHYs reports PHY ID as 0x0, but as of
commit 3ee82383f0
Author: Giulio Benetti <giulio.benetti@micronovasrl.com>
Date: Thu Nov 13 21:53:13 2008 +0000
phy: fix phy address bug
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
phy_device.c treats PHY ID == 0x0 as bogus IDs, and that results in
gianfar driver failure to see the TBI PHYs. This code snippet triggers:
if (!priv->tbiphy) {
printk(KERN_WARNING "SGMII mode requires that the device "
"tree specify a tbi-handle\n");
return;
}
Although tbi-handle is specified in the device tree.
Btw, technically PHY ID == 0x0 is a valid ID (if we ever see a PHY
manufactured by Xerox :-).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Russell King:
drivers/net/arm/etherh.c:649: error: unknown field 'ndo_set_mac_addr' specified in initializer
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add dependency on INFINIBAND_ADDR_TRANS
IPoIB: Do not join broadcast group if interface is brought down
RDMA/nes: Fix for NIPQUAD removal
IPoIB: Fix loss of connectivity after bonding failover on both sides
IB/mlx4: Don't register IB device for adapters with no IB ports
mlx4_core: Fix warning from min()
IB/ehca: spin_lock_irqsave() takes an unsigned long
drivers/net/wireless/p54/p54common.c: In function ‘p54_config’:
drivers/net/wireless/p54/p54common.c:1853: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-3945.c: In function ‘iwl3945_txpower_set_from_eeprom’:
drivers/net/wireless/iwlwifi/iwl-3945.c:2222: warning: ‘power_idx’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_dev_config’:
drivers/net/wireless/b43legacy/main.c:2468: warning: ‘up_dev’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/b43/main.c: In function ‘b43_op_config’:
drivers/net/wireless/b43/main.c:3264: warning: ‘gmode’ may be used uninitialized
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commits:
7a95d267fb
("net: ppp_generic - use idr technique instead of cardmaps")
ab5024ab23
("net: ppp_generic - use DEFINE_IDR for static initialization")
introduced usage of IDR functionality but broke userspace side.
Before this commits it was possible to allocate new ppp interface with
specified number. Now it fails with EINVAL. Fix it by trying to
allocate interface with specified unit number and return EEXIST if
fail which allow pppd to ask us to allocate new unit number.
And fix messages on memory allocation fails - add details that it's
PPP module who is complaining.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filip Aben says this fix is neccessary for big endian machines.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are powerpc specific drivers.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert arch/powerpc/ over to long long based u64:
-#ifdef __powerpc64__
-# include <asm-generic/int-l64.h>
-#else
-# include <asm-generic/int-ll64.h>
-#endif
+#include <asm-generic/int-ll64.h>
This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.
[Adjusted to not impact user mode (from paulus) - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The TX op should return NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TXD_W0_CIPHER field is a 1-bit field. It only acts as boolean value
to indicate if the frame must be encrypted or not.
The way rt2x00_set_field32() worked it would grab the least signifcant bit
from txdesc->cipher and use that as value. Because of that WEP 64 and TKIP
worked since they had odd-numbered values, while WEP 128 and AES were
even numbers and didn't work.
Correctly booleanize the txdecs->cipher value to allow the hardware to
encrypt the outgoing data. After this we can enable HW crypto by default again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should return NETDEV_TX_{OK,BUSY} instead of 0,-1 (this doesn't change
any current functionality).
Changes-licensed-under: 3-Clause-BSD
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to misunderstanding of the returned values allowed for the tx callback
of mac80211, rtl8187 was using skb's that had been freed. This problem was
triggered when the module was sujected to a rmmod/insmod cycle.
After that was fixed, the modules would not work after the rmmod/insmod cycle
until the USB device was reset.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch hopefully fixes a mac80211<->p54 interaction problem, which was
described by Larry Finger (ref: http://marc.info/?l=linux-wireless&m=123009889327707 )
I guess the warning was triggered by pending frames in the receive queue,
while we're doing a band change 5GHz.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This corrects usage of AR5K_CFG_ADHOC introduced in
"ath5k: Update PCU code". Also,
the name of the indicator is changed to AR5K_CFG_IBSS to more
accurately reflect its function. This change restores
beaconing in AP and mesh modes.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reverts "ath9k: Fix TX status reporting for retries and MCS index"
because that change ended up breaking ath9k rate control. While the
MCS index reporting to mac80211 was indeed fixed by the patch, it did
not take into account that the ath9k rate control algorithm was
updating private tables based on this index and the index comes
through the rate control API call, i.e., based on mac80211 TX status
call. In addition, it looks like the "fix" to remove +1 from TX status
'count' field was not correct based on ieee80211_tx_status()
implementation that counts the total of count values, but starting
from -1, not 0.
The TX status reporting for frames using MCS needs to be fixed
somehow, but it does not look like there is any easy fix for the ath9k
rate control algorithm, so the best option now seems to be to revert the
change and bring it back once the rate control code is cleaned up to
handle this better.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue with the sequence numbers of unaggregated
QoS frames, because of which the frames are handled in a different order
at the AP and resulted in MLME REPLAYFAILURE.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb doesn't strip the IV/ICV data from received frames,
so we don't need to set the RX_FLAG_IV_STRIPPED flag.
We do need to set the RX_FLAG_MMIC_STRIPPED flag for all
encryption types since the MMIC has been removed from the frame.
After this patch TKIP Hardware crypto works for rt2500usb.
WEP and AES are still failing.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be compatible with mac80211 following "mac80211: only create
default STA interface if supported", rtl8180 needs to set
NL80211_IFTYPE_STATION in interface_modes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Tested-by: Piter PUNK <piterpunk@unitednerds.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My first (minor) patch, hopefully this is correct.
Fix a typo in iwl-commands.h for CCK rates which needs 7 bits and not 4.
Signed-off-by: Daniel Wu <dyqith@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue_end() macro points to 1 position after the
queue, which means that if we want to know if queue
is at the end of the queue we should first increment
the position and then check if it is a valid entry.
This fixes a segmentation fault which only occurs when
the device has enough endpoints to provide a dedicated
endpoint for all TX queues (which likely won't happen
for rt2500usb and rt73usb, but will happen for rt2800usb).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All LM87 firmwares need a explicit termination "packet",
in oder to finish the pending transfer properly.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two small flaws:
- restore the original TKIP IV if we altered it.
- reserve & initialize ICV with zeros.
This is actually only necessary for some obsolete p54usb firmwares.
But we don't know yet, if all devices are compatible with the new revisions.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Michael Jarosch <mitsch@riotmusic.de>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
0x1b is a 3945 specific command, we should print it too when debugging.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmasks have to be updated before setting the channel,
since the HW reset routine uses them to set the appropriate registers.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_ATH9K=y results in build issues if CONFIG_RFKILL=m since ath9k
does not depend on rfkill in kconfig (i.e., CONFIG_RFKILL is used to
select whether to enable rfkill in ath9k), but uses its functions if
rfkill is enabled. Enforce ath9k to be build as a module if
CONFIG_RFKILL=m to avoid this invalid configuration.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB ID for Thomson Speedtouch 121g to p54usb.
Signed-off-by: Michiel <michiel@ettema.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The short preamble mode was not correctly detected during TX,
rt2x00 used the rate->hw_value_short field but mac80211 is not
using this field that way.
Instead the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE should be
used to determine if the frame should be send out using
short preamble or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add USB ID for the Linksys WUSB200 Wireless-G Business USB Adapter to
rt73usb.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On x86_64 architecture with 4K page size and SLUB debugging enabled, stress
testing on p54usb has resulted in skb allocation failures of O(1) and extreme
page fragmentation. Reducing rx_mtu fixes this problem by reducing the size of
all receive skb allocations to be of O(0). This change does not impact
performance in any way.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "rt2x00: Fix LED state handling", rt2x00leds_led_radio wrongly
checks that the LED type is LED_TYPE_ASSOC. This patch makes it check
for LED_TYPE_RADIO once again.
Signed-off-by: Andrew Price <andy@andrewprice.me.uk>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The UCC Event Register (UCCE) already has unambigous macro definitions in qe.h,
so we should not be defining our own in the UCC Ethernet driver.
Removed unused local variable 'dev' from ucc_geth_poll(), which fixes
a warning caused by commit 908a7a16b8
("net: Remove unused netdev arg from some NAPI interfaces.").
Replaced in_be/out_be pairs with setbits32 or clrbits32, where applicable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a system with a Chelsio adapter (driven by cxgb3) whose ports are
part of a Linux bridge. Recently I updated the kernel and discovered
that things stopped working because cxgb3 was doing LRO on packets that
were passed into the bridge code for forwarding. (Incidentally, this
problem manifested itself in a strange way that made debugging a bit
interesting -- for some reason, the skb_warn_if_lro() check in bridge
didn't trigger and these LROed packets were forwarded out a forcedeth
interface, and caused the forcedeth transmit path to get stuck)
This is because cxgb3 has no way of keeping state for the LRO flag until
the interface is brought up, so if the bridging code disables LRO while
the interface is down, then cxgb3_up() will just reenable LRO, and on my
Debian system at least, the init scripts add interfaces to a bridge
before bringing the interfaces up.
Fix this by keeping track of each interface's LRO state in cxgb3 so that
when bridge disables LRO, it stays disabled in cxgb3_up() when the
interface is brought up. I did this by changing the rx_csum_offload
flag into a pair of bit flags; the effect of this on the rx_eth() fast
path is miniscule enough that it should be fine (eg on x86, a cmpb
instruction becomes a testb instruction).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the SFX7101 requires software power control. This was
incorrectly being applied to the SFT9001 rev A as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change lets "cat /proc/interrupts" show the name of the ethernet
device (e.g. eth0) rather than the driver name (smsc911x).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if this code path is ever hit, the platform_data struct isn't properly
configured with a bus width flag so the device won't work (hence the
BUG()).
This patch adds a dummy return statement to eliminate this compiler
warning:
drivers/net/smsc911x.c: In function 'smsc911x_reg_read':
drivers/net/smsc911x.c:148: warning: control reaches end of non-void function
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential race condition between scheduling napi and
completing napi poll. The call to netif_rx_schedule should be under
protection of the lock (as is the completion), otherwise, interrupts
could be masked off.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the feature flag for mgmt unit as it is not used for
this chipset.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to sleep while waiting for the hardware
semaphore to become available.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for dev id 8000 is pushed out until 2.6.30.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Putting back ql_read_sh_reg() function and using rmb() instead of
volatile.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bumps up the version number and adds current year to copyright.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential race condition between xmit thread and xmit
completion thread. The calculation of empty tx descriptors is not
performed under the lock. This could cause it to set the stop flag while
the completion thread finishes all tx's. This will result in the tx
queue in stopped state and no one to wake it up.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices were converted incorrectly and are missing the validate
address hooks.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same kind of wrapper that can also be found in many
other network device drivers.
Tested with a freescale MPC8349E host CPU:
Toggled the interface LEDs on a DP83865 PHY.
Signed-off-by: Clifford Wolf <clifford@clifford.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test. I have also taken advantage of the availability
of the value of priv->dev in the subsequent calls to netif_stop_queue and
netif_carrier_off.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set this bit by calling device_set_wakeup_enable().
This restores proper WOL for the 3c59x driver.
Reported-and-tested-by: Graeme Wilford <gwilford@gmail.com>
Reported-by: Gunnar Degnbol <degnbol@danbbs.dk>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name interrupt vectors according to the new naming standard, by Robert
Olsson and DaveM.
The qlge driver were very close to the new standard, thus the change
is kind of trivial.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom 4400 puts a header of configurable size (apparently needs
to be at least 28 bytes) in front of received packets. When handling
this, the previous code accidentally added the offset 30 *twice* for
the software and once for the hardware, thereby cancelling out the
IP alignment effect of the 30 byte padding and wasting an additional
30 bytes of memory per packet.
This patch fixes this problem and improves routing throughput by
about 30% on MIPS, where unaligned access is expensive.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds process name of the current mutex holder to the WARN message output
when the e1000e driver attempts to acquire the nvm_mutex and finds that
it is already being held. With this patch the WARN message indicates
both the process name of the current mutex holder and the process name of
the attempted acquisition, which together will help to identify the
contending codepaths.
Signed-off-by: David Graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump version to 0.21 and release date to 09Jan2009.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not depend on EXPERIMENTAL and the driver is
not experimental, so remove this warning.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the ethernet driver assign a random ethernet
MAC address when the bootloader does not set it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes warnings and such traces that appear when doing
an ifconfig down on the interface:
WARNING: at arch/x86/kernel/pci-dma.c:376 dma_free_coherent+0x40/0x7d()
Modules linked in:
Signed-off-by: Joe Chou <joe.chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for commit af0490810c (irda: convert to internal stats)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent cpumask changes changed num_possible_cpus() from returning an int
to returning an unsigned int. This means that doing
min(num_possible_cpus(), <int expression>)
now produces a warning like
drivers/net/mlx4/main.c: In function 'mlx4_enable_msi_x':
drivers/net/mlx4/main.c:915: warning: comparison of distinct pointer types lacks a cast
Fix this by using min_t(int, ...).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (84 commits)
wimax: fix kernel-doc for debufs_dentry member of struct wimax_dev
net: convert pegasus driver to net_device_ops
bnx2x: Prevent eeprom set when driver is down
net: switch kaweth driver to netdevops
pcnet32: round off carrier watch timer
i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
wimax: testing for rfkill support should also test for CONFIG_RFKILL_MODULE
wimax: fix kconfig interactions with rfkill and input layers
wimax: fix '#ifndef CONFIG_BUG' layout to avoid warning
r6040: bump release number to 0.20
r6040: warn about MAC address being unset
r6040: check PHY status when bringing interface up
r6040: make printks consistent with DRV_NAME
gianfar: Fixup use of BUS_ID_SIZE
mlx4_en: Returning real Max in get_ringparam
mlx4_en: Consider inline packets on completion
netdev: bfin_mac: enable bfin_mac net dev driver for BF51x
qeth: convert to net_device_ops
vlan: add neigh_setup
dm9601: warn on invalid mac address
...
This converts the pegasus driver to use of the new net_device_ops structure
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the kaweth ethernet USB driver to netdevops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link check watchdog timer on this driver fires every two seconds, but
since not aligned it causes extra wakeups. It is more important on this
driver than most because it is the hardware that is emulated by default
when using network interfaces on VMware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code was assuming PM was always enabled, which is not
correct. Code which accesses members in the struct usb_device that are
dependant on CONFIG_PM must be protected the same.
Reported by Randy Dunlap from a build error in the linux-next tree on
07/01/2009.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bumps release number to 0.20 and 07Jan2009.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some bootloader/BIOSes do not set the MAC
address, warn about that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the driver properly initialize the PHY
status if not correctly set by the bootloader/BIOS.
It prevents some boards to bring up the link on boot.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some printks which were not prefixed
with DRV_NAME, useful when having multiple cards/drivers
on the system.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") went back to using BUS_ID_SIZE
instead of sizeof() as per the larger patch series that will remove
"char bus_id[20]" from struct device.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Was trying to unmap work queue entries that had inline packets,
so naturally weren't mapped.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add warnings on invalid mac address to help disclose/debug problems.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise unicast RX will only work in promisc mode.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to net_device_ops and internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to net_device_ops and internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to internal net_device-stats and net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to net_device_ops and internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to net_device_ops and internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan_rx_register fuction is now in net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
