[why]
With visual confirm enabled, displays where ODM combine is enabled
has a test pattern stuck on the right half of the display even
though the display is unblanked.
[how]
Add a condition to not show the colour ramp test pattern when the
display is unblanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before a statically allocated PPS data structure, that did
get zeroed-out at startup, had been re-used for making packed PPS
SDP. With S3 fix, using a non-initialized PPS data structure was
introduced, while wrongly assuming it'd get initialized before it's
populated. As a consequence 'vbr_enable' and perhaps some other
fields are left uninitialized when making packed PPS SDP. This can
affect 'simple_422' as well because of the way PPS SDP packing is
done (the fields are not masked first, only shifted). The behavior
will be different, depending on the content of uninitialized data.
[how]
Zero-out PPS data structure at initialization time before it's
populated
Fixes: 1a9e3d4569 ("drm/amd/display: Set DSC before DIG front-end is connected to its back-end")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous odm change broke stream enable by always setting
n_multiply as if odm was on.
This fixes the check for odm by making sure opp count is >1
rather than not 0.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With Scatter Gather enabled, HUBP underflows during MPO enabled video
playback. hubp_init has a register write that fixes this problem, but
the register is cleared when HUBP gets power gated.
[how]
Make a call to hubp_init during enable_plane, so that the fix can
be applied after HUBP powers back on again.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable_audio_stream gets enum option as a paramenter which will decide
if we free acquired resources or not. However checks for the option is
guarded by the other condition which check if audio stream is getting
diabled more than once. With both conditions combined, if we attempt to
disable audio stream twice in a row, first with keep and second with
free as an option, we will never free any resources, which will make
system think there is audio endpoint connected even after we plug out
the device
[How]
Get rid of option as parameter to disable_audio_stream and move the part
of the code that free acquired resources to outside where to keep or to
free resources is actually determined
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.
Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.
Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 9e14d4f17e.
optc dsc config was causing warnings due to missing register
definitions. With the registers restored, the function can
be re-enabled
The reverted commit also disabled sanity checks and dsc
power gating. The sanity check warnings are not associated
with dsc, and power gating on dsc still has an issue on
non-dsc monitors where the dsc hardware block is never init
and so cannot respond to power gating requests. Therefore,
those are left as is
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous SOC bounding box firmware loading logic was for NV10, when we
still had it in firmware. Now that it's brought into driver code, and
NV12 BB is in firmware, this logic needs to be repurposed for NV12.
[How]
Set SOC_BOUNDING_BOX_VALID to false, and add the dcn_2_0_nv12_soc BB
struct. In init_soc_bounding_box, load firmware to nv12 BB instead.
In addition, conditionally update and patch the BB, depending on ASIC
REV.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the paremeters are extracted as if dml is calculating
using pipes as we pass them in. in reality, dml internally merges
pipes into planes if pipe split is detected.
This change adds reverse logic to dcn20_calculate_dlg_params so
that the global sync parameters can be correctly extracted for
all the pipes when pipe split is enabled.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OGAM_MEM_PWR could stay in light up when driver woke up to update gamma.
either disable MEM_LOW power feature or set to OGAM_bypass could make artificial color distortion goes away.
Easy reproduce after LOW_MEM Power feature enables and resume from S3.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Julian Parkin <jparkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A misleading message "Programming PPS" appears before both programming
and "query PPS" functions
[how]
Move the message from "log PPS" function to "program PPS" function
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If DSC is available, a higher picture quality is achieved by using
DSC with 4:4:4 format. Using 4:2:2 instead does not offer any benefit
and would only introduce loss of quality. Removing it reduces
maintenance and testing effort.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to change interface function signature / add an enum
to reflect the available register field values
[How]
- Add a new enum and modify existing functions to use it instead
of bool
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are currently two interfaces for exactly the same thing:
hupb_update_dchub in hupb and update_dchub in hubbub. The hubbub
version is currently unused past dcn10, largely because the call
from the dcn10 hardware sequencer does not call through the
interface, so the hupb interface was used instead. This is
confusing because of the duplicate code, the unused functions,
and the fact that more that one block currently owns this set
of registers.
[How]
Remove the hubp interface entirely, as well as the register
declarations that are not longer needed because of this. Change
the call site to always call the hubbub version through the
interface. Fix the update_dchub function in dcn20_hubbub.c to
program the correct registers for dcn20.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Resource mapping done in dcn20_validate_bandwidth has a flaw: When a full
update is performed, the HWSS will only update the MPCC tree for the stream
that is updated as opposed to all streams. This means that when mapping pipes
in validation, care must be taken to not change any existing mapping, otherwise it
leads to partial hw programming
[how]
it's not strictly necessary to track which stream/mpcc tree is being updated, but
rather it's sufficient to compare current and new state and just keep pipes that were
previously already mapped unchanged.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
At the time DIG FE is connected to its BE, the clocks in OTG are enabled and
PHY will also be set up. When DSC has to be used to fit the stream into the
available bandwidth, without DSC being set DIG could get exposed to the
higer bandwidth it (or link) could handle. This causes the HW to "reject"
video enable setup (the register shows that video enable was attempted, but
the status bit shows it as disabled).
[how]
- Separate DSC setup into DSC register config and DSC PPS SDP setup
- Move most of the DSC setup (register config) to before
dcn10_link_encoder_connect_dig_be_to_fe() is called
- Set up DSC PPS SDP after DIG FE is connected to its BE. This is because
setting DSC PPS SDP before that has no effect.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since
DMLv2 has gone through proper validation. v2 can now be used as the default and 1
level of fallback can be removed
[how]
remove previous workaround implemenation
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot (building SW state inheriting BIOS-initialized timing) was
enabled on DCN2, including fixes
[How]
Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/
Pixel clock.
This is part 2 of 2 for seamless boot NV10
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For seamless boot the init_hw sequence must be split into
actual hardware vs pipes, in order to defer pipe initialization to set mode
and skip of pipe-destructive sequences
[How]
made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit
deleted dcn20 specific versions. This is part 1 of a 2 partimplementation
of seamless boot
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When planes are enabled, they must be enabled using VSYNC update (not immediate).
However, before the VUPDATE occurs, DM may call with an "immediate" flip which is address
only. This operation would normally be okay, but if the locking for immediate flip happens
to occur before the VUPDATE associated with the initial plane enablement, it will cause HW
to hang.
[how]
HWSS should enforce plane enable in HW to be synchronous with the call that enables the plane.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not.
This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need
an increased divider will temporarily have actual DPP clock drop below minimum while DTO
double buffering takes effect. This results in temporary underflow.
[how]
To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the
ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase.
When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because
we do not use dividers larger than 1.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently every time DC wants to access firmware info we make a call
into VBIOS. This makes no sense as there is nothing that can change
runtime inside fw info and can cause issues when calling unstable
bios during bringup.
This change eliminate this behavior by only calling bios once for fw
info and keeping it stored as part of dc_bios.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were previously forcing the uclk for every state to max and reducing
the switch time to prevent uclk switching from occuring. This workaround
was previously needed in order to avoid hangs + underflow under certain
display configurations.
Now that DC has the proper fix complete we can drop the hacks and
improve power for most display configurations.
[How]
We still need the function pointers hooked up to grab the real uclk
states from pplib. The rest of the prior hack can be reverted.
The key requirements here are really just DC support, updated firmware,
and support for disabling p-state support when needed in pplib/smu.
When these requirements are met uclk switching works without underflow
or hangs.
Fixes: 02316e963a ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to support uclk switching on NV10 the SOC bounding box
needs to be updated.
[How]
We currently read the constants from the gpu info FW, but supporting
workarounds in DC for different versions of the FW adds additional
complexity to the codebase.
NV10 has been released so it's cleanest to keep the bounding box and
source code in sync by embedding the bounding box like we do for
other ASICs.
Fixes: 02316e963a ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
arch/x86/Makefile disables SSE and SSE2 for the whole kernel. The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2. Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines for Clang.
This was originally landed in:
commit 1011745073 ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
but reverted in:
commit 193392ed9f ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
due to bugreports from GCC builds. Add guards to only do so for Clang.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=109487
Link: https://github.com/ClangBuiltLinux/linux/issues/327
Suggested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull Wimplicit-fallthrough enablement from Gustavo A. R. Silva:
"This marks switch cases where we are expecting to fall through, and
globally enables the -Wimplicit-fallthrough option in the main
Makefile.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
With these changes, we completely get rid of all the fall-through
warnings in the kernel"
* tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
Makefile: Globally enable fall-through warning
drm/i915: Mark expected switch fall-throughs
drm/amd/display: Mark expected switch fall-throughs
drm/amdkfd/kfd_mqd_manager_v10: Avoid fall-through warning
drm/amdgpu/gfx10: Fix missing break in switch statement
drm/amdkfd: Fix missing break in switch statement
perf/x86/intel: Mark expected switch fall-throughs
mtd: onenand_base: Mark expected switch fall-through
afs: fsclient: Mark expected switch fall-throughs
afs: yfsclient: Mark expected switch fall-throughs
can: mark expected switch fall-throughs
firewire: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[Why]
DC configures the GSL group for the pipe when pipe_split is enabled
and we're switching flip types (buffered <-> immediate flip) on DCN2.
In order to record what GSL group the pipe is using DC stores it in
the pipe's stream_res. DM is not aware of this internal grouping, nor
is DC resource.
So when DM creates a dc_state context and passes it to DC the current
GSL group is lost - DM never knew about it in the first place.
After 3 immediate flips we run out of GSL groups and we're no longer
able to correctly perform *any* flip for multi-pipe scenarios.
[How]
The gsl_group needs to be copied to the new context.
DM has no insight into GSL grouping and could even potentially create
a brand new context without referencing current hardware state. So this
makes the most sense to have happen in DC.
There are two places where DC can apply a new context:
- dc_commit_state
- dc_commit_updates_for_stream
But what's shared between both of these is apply_ctx_for_surface.
This logic only matters for DCN2, so it can be placed in
dcn20_apply_ctx_for_surface. Before doing any locking (where the GSL
group is setup) we can copy over the GSL groups before committing the
new context.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersen.wu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing support in DC for pstate only accounts for a single latency. This is sufficient when the
variance of latency is small, or that pstate support isn't necessary for correct ASIC functionality.
Newer ASICs violate both existing assumptions. PState support is mandatory of correct ASIC
functionality, but not all latencies have to be supported. Existing code supports a "full p state" which
allows memory clock to change, but is hard for DCN to support (as it requires very large buffers).
New code will now fall back to a "dummy p state" support when "full p state" cannot be support.
This easy p state support should always be allowed.
[how]
Define a new latency in socBB. Add fallback logic to support it. Note DML is also updated to ensure
that fallback will always work.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN2x asic, the MPCC status register definition changed, and
our logic for assert is incorrect. disabled is valid state,
where we should see idle and not busy, where as in not
disabled state, we should see not idle.
[How]
Change assert condition to be more sensible.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Code to enable DCN20 dynamic metadata feature is duplicated in two places
and was added to DCE110 enable stream.
[How]
Create DCN20 specific enable stream function for clarity, and add a hardware
sequencer function to program dynamic metadata to avoid the duplicate
code.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
update_bounding_box calculates intermediate bb states based on clock relationship
however, the last state doesn't need to maintain a minimum relationship, but should
actually contain maximum of every clock. otherwise maximum clocks are not usable
[how]
once the calculated bb is built, override the last state with max values
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dual plane dcc programming support for
surfaces.
Removes unions from plane size and dcc params as they
serve no practical purpose only making our code
more convoluted. This results in easy dual plane
dcc and surface size programming.
Temporary diags_dm code is used to handle the interface
change without breaking functionality as a diags change
needs to be applied after this one.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
