Before it disappears completely, move transaction phase enum under
transaction structure and make attr/obj structures a bit cleaner.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, the memory allocation in prepare/commit state is done separatelly
in each driver (rocker). Introduce the similar mechanism in generic
switchdev code, in form of queue. That can be used not only for memory
allocations, but also for different items. Abort item destruction
is handled as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is temporary, name "trans" will be used for something else and
"trans_ph" will eventually disappear.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-23
This series contains updates to ixgbe only.
Mark provides all the changes in this series, first clears the destination
location for I2C data initially so that the received data will not be
corrupted by previous attempts. Then reduced the pauses/delays in the
PHY detection when no SFP is present by reducing the number of retires,
once an SFP is detected, the "normal" number of retries in PHY detection
will be used. Added support for X55EM_x SFP+ dual-speed, and fixed 1G and
10G link stability for X550EM_x by configuring the CS4227 correctly by
moving code to ixgbe_setup_mac_link_sfp_x550em(). Added functionality to
reset CS4227, since on some platforms the CS4227 does not initialize
properly. Next reduces the SFP polling rate, due to when an SFP is not
present, the I2C timeouts that result are very costly. So prevent the
SFP polling from being done more than once every two seconds. Added
support for I2C bus MUX. Fixed the setting of RDRXCTL register which
should fall through X540 and 82599, not 82598. In addition, added small
packet padding support in X550 by setting RDRXCTL.PSP when the driver is
in SRIOV mode. Fixed a known hardware issue where the PCI transactions
pending bit sticks high when there are pending transactions, so
workaround the issue by wait and then continue with our reset flow.
Added a new device ID for X550EM device with SFPs. Provided a fix with
the DCA setup, which was suggested by Alex Duyck <aduyck@mirantis.com>,
by making it so that we always set the relaxed ordering bits related to
the DCA registers even if DCA is not enbaled. Then moves the
configuration out of the ixgbe_down() and into ixgbe_configure() before
enabling the transmit and receive rings. This ensures that DCA is
configured correctly before starting the processing of packets.
Fixed VM-to-VM loopback mode which requires that FCRTH be set, but
the datasheets did not specify what the value should be. It has now
been determined that the correct value should be RXPBSIZE - (24*1024).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After a good amount of debugging, I found bnx2x was byte swaping
the 40 bytes of rss_key.
If we byte swap the key, then bnx2x generates hashes matching
MSDN specs as documented in (Verifying the RSS Hash Calculation)
https://msdn.microsoft.com/en-us/library/windows/hardware/ff571021%
28v=vs.85%29.aspx
It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_u32 to read the "clock-frequency" property instead
of using of_get_property with return value checks.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of X550em_x SFP+ support, the driver is now
functionally equivalent to what will be the 4.2.1 driver when
released, so change the version to match.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal interrupt (IXGBE_EIMS_TS) is not an SDP, so it
doesn't need to be enabled in ixgbe_setup_gpie(). In fact the
value is simply not for the GPIE register at all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and X540 datasheets require that FCRTH be "set" for Tx
switching (VM-to-VM loopback) but it did not previously specify what
the value should be set to. It has now been determined that
the correct value is RXPBSIZE - (24*1024).
This setting is also required for later devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A logic error here results in the adapter_stopped flag only being
cleared when ixgbe_setup_fc returns an error. Correct the logic.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.
Thanks to Alex Duyck for this fix.
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device ID for X550EM device with SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. This is done to addresses a known HW
issue where the PCI transactions pending bit sticks high when there
are pending transactions. HW engineering instructed to workaround
this issue by wait and then continue with our reset flow.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timeout path is supposed to release the semaphore, so do that.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take control of an I2C mux that selects which SFP is attached to
the I2C bus. The control of the mux is captured in the taking and
releasing of the related semaphore. Because only port 1 can control
the mux, port 1 always leaves the mux set to select port 0.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since SFP+ can be used with some X550 devices, permit them to be
detected.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Configures the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the previous flow, and is due to the way the CS4227 is
implemented.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link
code was moved from ixgbe_82599.c to ixgbe_common.c for use by
X550EM. SFP MAC link code is added to x550EM.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the number of retries during PHY detection. This reduces
pauses when no SFP is present. Once an SFP is detected, the normal
retry count will be used.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the destination location for I2C data initially so that
the received data will not be affected by previous attempts.
This could have returned wrong data in certain retry sequences.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case the DaVinci Emac is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-22
This series contains updates to e1000, e1000e, igbvf, ixgbe, ixgbevf and
fm10k.
Jacob provides several updates for fm10k, which cleans up comments and
most notably a fix for a corner case issue with the PF/VF mailbox code.
The issue being fm10k_mbx_reset_work clears various states about the
mailbox, but does not clear the Tx FIFO head/tail pointers. We also
are not able to simply clear these pointers, as we would drop
untransmitted messages without error. Also adds support for extra debug
statistics, which provides the ability to see what the PF thinks the
VF mailboxes look like.
Don adds support for SFP+ in X550 and support for SCTP flow director
filters SCTP mask.
Francois Romieu dusts off the e1000 driver and removes some dead calls
to e1000_init_eeprom_params().
Toshiaki Makita provides three patches to enable TSO for stacked VLAN's
on e1000e, igbvf and ixgbevf.
Mark provides the first of several ixgbe updates. First updates the
driver to accept SFP not present error for all devices, since an SFP
can still be inserted. Adds support for SFP insertion interrupt on
X550EM devices with SPFs. Adds I2C combined operations on X550EM
(not X550) devices. Moved the setting of lan_id to before any I2C
eeprom access. Lastly, set the bit bang mode in the hardware when
performing bit banding I2C operations on X550.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We are seeing unexplained TX timeouts under heavy load. Let's try to get
a better idea of what's going on.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The low 16 bits of the 'opts1' field in the TX descriptor are supposed
to still contain the buffer length when the descriptor is handed back to
us. In practice, at least on my hardware, they don't. So stash the
original value of the opts1 field and get the length to unmap from
there.
There are other ways we could have worked out the length, but I actually
want a stash of the opts1 field anyway so that I can dump it alongside
the contents of the descriptor ring when we suffer a TX timeout.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We calculate the value of the opts1 descriptor field in three different
places. With two different behaviours when given an invalid packet to
be checksummed — none of them correct. Sort that out.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a TSO frame in multiple buffers, we were neglecting to set
the first descriptor up in TSO mode.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a certain amount of staring at the debug output of this driver, I
realised it was lying to me.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an RX interrupt was already received but NAPI has not yet run when
the RX timeout happens, we end up in cp_tx_timeout() with RX interrupts
already disabled. Blindly re-enabling them will cause an IRQ storm.
(This is made particularly horrid by the fact that cp_interrupt() always
returns that it's handled the interrupt, even when it hasn't actually
done anything. If it didn't do that, the core IRQ code would have
detected the storm and handled it, I'd have had a clear smoking gun
backtrace instead of just a spontaneously resetting router, and I'd have
at *least* two days of my life back. Changing the return value of
cp_interrupt() will be argued about under separate cover.)
Unconditionally leave RX interrupts disabled after the reset, and
schedule NAPI to check the receive ring and re-enable them.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A deadlock trace is seen in netcp driver with lockup detector enabled.
The trace log is provided below for reference. This patch fixes the
bug by removing the usage of netcp_modules_lock within ndo_ops functions.
ndo_{open/close/ioctl)() is already called with rtnl_lock held. So there
is no need to hold another mutex for serialization across processes on
multiple cores. So remove use of netcp_modules_lock mutex from these
ndo ops functions.
ndo_set_rx_mode() shouldn't be using a mutex as it is called from atomic
context. In the case of ndo_set_rx_mode(), there can be call to this API
without rtnl_lock held from an atomic context. As the underlying modules
are expected to add address to a hardware table, it is to be protected
across concurrent updates and hence a spin lock is used to synchronize
the access. Same with ndo_vlan_rx_add_vid() & ndo_vlan_rx_kill_vid().
Probably the netcp_modules_lock is used to protect the module not being
removed as part of rmmod. Currently this is not fully implemented and
assumes the interface is brought down before doing rmmod of modules.
The support for rmmmod while interface is up is expected in a future
patch set when additional modules such as pa, qos are added. For now
all of the tests such as if up/down, reboot, iperf works fine with this
patch applied.
Deadlock trace seen with lockup detector enabled is shown below for
reference.
[ 16.863014] ======================================================
[ 16.869183] [ INFO: possible circular locking dependency detected ]
[ 16.875441] 4.1.6-01265-gfb1e101 #1 Tainted: G W
[ 16.881176] -------------------------------------------------------
[ 16.887432] ifconfig/1662 is trying to acquire lock:
[ 16.892386] (netcp_modules_lock){+.+.+.}, at: [<c03e8110>]
netcp_ndo_open+0x168/0x518
[ 16.900321]
[ 16.900321] but task is already holding lock:
[ 16.906144] (rtnl_mutex){+.+.+.}, at: [<c053a418>] devinet_ioctl+0xf8/0x7e4
[ 16.913206]
[ 16.913206] which lock already depends on the new lock.
[ 16.913206]
[ 16.921372]
[ 16.921372] the existing dependency chain (in reverse order) is:
[ 16.928844]
-> #1 (rtnl_mutex){+.+.+.}:
[ 16.932865] [<c06023f0>] mutex_lock_nested+0x68/0x4a8
[ 16.938521] [<c04c5758>] register_netdev+0xc/0x24
[ 16.943831] [<c03e65c0>] netcp_module_probe+0x214/0x2ec
[ 16.949660] [<c03e8a54>] netcp_register_module+0xd4/0x140
[ 16.955663] [<c089654c>] keystone_gbe_init+0x10/0x28
[ 16.961233] [<c000977c>] do_one_initcall+0xb8/0x1f8
[ 16.966714] [<c0867e04>] kernel_init_freeable+0x148/0x1e8
[ 16.972720] [<c05f9994>] kernel_init+0xc/0xe8
[ 16.977682] [<c0010038>] ret_from_fork+0x14/0x3c
[ 16.982905]
-> #0 (netcp_modules_lock){+.+.+.}:
[ 16.987619] [<c006eab0>] lock_acquire+0x118/0x320
[ 16.992928] [<c06023f0>] mutex_lock_nested+0x68/0x4a8
[ 16.998582] [<c03e8110>] netcp_ndo_open+0x168/0x518
[ 17.004064] [<c04c48f0>] __dev_open+0xa8/0x10c
[ 17.009112] [<c04c4b74>] __dev_change_flags+0x94/0x144
[ 17.014853] [<c04c4c3c>] dev_change_flags+0x18/0x48
[ 17.020334] [<c053a9fc>] devinet_ioctl+0x6dc/0x7e4
[ 17.025729] [<c04a59ec>] sock_ioctl+0x1d0/0x2a8
[ 17.030865] [<c0142844>] do_vfs_ioctl+0x41c/0x688
[ 17.036173] [<c0142ae4>] SyS_ioctl+0x34/0x5c
[ 17.041046] [<c000ff60>] ret_fast_syscall+0x0/0x54
[ 17.046441]
[ 17.046441] other info that might help us debug this:
[ 17.046441]
[ 17.054434] Possible unsafe locking scenario:
[ 17.054434]
[ 17.060343] CPU0 CPU1
[ 17.064862] ---- ----
[ 17.069381] lock(rtnl_mutex);
[ 17.072522] lock(netcp_modules_lock);
[ 17.078875] lock(rtnl_mutex);
[ 17.084532] lock(netcp_modules_lock);
[ 17.088366]
[ 17.088366] *** DEADLOCK ***
[ 17.088366]
[ 17.094279] 1 lock held by ifconfig/1662:
[ 17.098278] #0: (rtnl_mutex){+.+.+.}, at: [<c053a418>]
devinet_ioctl+0xf8/0x7e4
[ 17.105774]
[ 17.105774] stack backtrace:
[ 17.110124] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 17.118637] Hardware name: Keystone
[ 17.122123] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 17.129862] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 17.137079] [<c05ff450>] (dump_stack) from [<c0068e34>]
(print_circular_bug+0x210/0x330)
[ 17.145161] [<c0068e34>] (print_circular_bug) from [<c006ab7c>]
(validate_chain.isra.35+0xf98/0x13ac)
[ 17.154372] [<c006ab7c>] (validate_chain.isra.35) from [<c006da60>]
(__lock_acquire+0x52c/0xcc0)
[ 17.163149] [<c006da60>] (__lock_acquire) from [<c006eab0>]
(lock_acquire+0x118/0x320)
[ 17.171058] [<c006eab0>] (lock_acquire) from [<c06023f0>]
(mutex_lock_nested+0x68/0x4a8)
[ 17.179140] [<c06023f0>] (mutex_lock_nested) from [<c03e8110>]
(netcp_ndo_open+0x168/0x518)
[ 17.187484] [<c03e8110>] (netcp_ndo_open) from [<c04c48f0>]
(__dev_open+0xa8/0x10c)
[ 17.195133] [<c04c48f0>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 17.203129] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 17.211560] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 17.219729] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 17.227378] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 17.234939] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 17.242242] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 17.258855] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
[ 17.271282] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 17.279712] in_atomic(): 1, irqs_disabled(): 0, pid: 1662, name: ifconfig
[ 17.286500] INFO: lockdep is turned off.
[ 17.290413] Preemption disabled at:[< (null)>] (null)
[ 17.295728]
[ 17.297214] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 17.305735] Hardware name: Keystone
[ 17.309223] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 17.316970] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 17.324194] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 17.332112] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 17.340724] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>]
(dev_set_rx_mode+0x1c/0x28)
[ 17.348982] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>]
(__dev_open+0xc4/0x10c)
[ 17.356724] [<c04c490c>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 17.364729] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 17.373166] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 17.381344] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 17.388994] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 17.396563] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 17.403873] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 17.413772] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.20.2) started
Sending discover...
[ 18.690666] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
Sending discover...
[ 22.250972] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
[ 22.258721] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.265458] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 22.273896] in_atomic(): 1, irqs_disabled(): 0, pid: 342, name: kworker/1:1
[ 22.280854] INFO: lockdep is turned off.
[ 22.284767] Preemption disabled at:[< (null)>] (null)
[ 22.290074]
[ 22.291568] CPU: 1 PID: 342 Comm: kworker/1:1 Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 22.300255] Hardware name: Keystone
[ 22.303750] Workqueue: ipv6_addrconf addrconf_dad_work
[ 22.308895] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 22.316643] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 22.323867] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 22.331786] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 22.340394] [<c03e9840>] (netcp_set_rx_mode) from [<c04c9d18>]
(__dev_mc_add+0x54/0x68)
[ 22.348401] [<c04c9d18>] (__dev_mc_add) from [<c05ab358>]
(igmp6_group_added+0x168/0x1b4)
[ 22.356580] [<c05ab358>] (igmp6_group_added) from [<c05ad2cc>]
(ipv6_dev_mc_inc+0x4f0/0x5a8)
[ 22.365019] [<c05ad2cc>] (ipv6_dev_mc_inc) from [<c058f0d0>]
(addrconf_dad_work+0x21c/0x33c)
[ 22.373460] [<c058f0d0>] (addrconf_dad_work) from [<c0042850>]
(process_one_work+0x214/0x8d0)
[ 22.381986] [<c0042850>] (process_one_work) from [<c0042f54>]
(worker_thread+0x48/0x4bc)
[ 22.390071] [<c0042f54>] (worker_thread) from [<c004868c>]
(kthread+0xf0/0x108)
[ 22.397381] [<c004868c>] (kthread) from [<c0010038>]
Trace related to incorrect usage of mutex inside ndo_set_rx_mode
[ 24.086066] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 24.094506] in_atomic(): 1, irqs_disabled(): 0, pid: 1682, name: ifconfig
[ 24.101291] INFO: lockdep is turned off.
[ 24.105203] Preemption disabled at:[< (null)>] (null)
[ 24.110511]
[ 24.112005] CPU: 2 PID: 1682 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 24.120518] Hardware name: Keystone
[ 24.124018] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 24.131772] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 24.138989] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 24.146908] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 24.155523] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>]
(dev_set_rx_mode+0x1c/0x28)
[ 24.163787] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>]
(__dev_open+0xc4/0x10c)
[ 24.171531] [<c04c490c>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 24.179528] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 24.187966] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 24.196145] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 24.203803] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 24.211373] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 24.218676] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 24.227156] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netcp_rxpool_refill() that refill descriptors and attached
buffers to fdq while interrupt is enabled as part of NAPI poll. Doing
it while interrupt is disabled could be beneficial as hardware will
not be starved when CPU is busy with processing interrupt.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netcp_module_probe() doesn't check the return value of
of_parse_phandle() that points to the interface data for the
module and then pass the node ptr to the module which is incorrect.
Check for return value and free the intf_modpriv if there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if netcp_allocate_rx_buf() fails due no descriptors
in the rx free descriptor queue, inside the netcp_rxpool_refill() function
the iterative loop to fill buffers doesn't terminate right away. So modify
the netcp_allocate_rx_buf() to return an error code and use it break the
loop when there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp interface is not fully initialized before attach the module
to the interface. For example, the tx pipe/rx pipe is initialized
in ethss module as part of attach(). So until this is complete, the
interface can't be registered. So move registration of interface to
net device outside the current loop that attaches the modules to the
interface.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netcp_core is the first driver that will get initialized and the modules
(ethss, pa etc) will then get initialized. So the code at the end of
netcp_probe() that iterate over the modules is a dead code as the module
list will be always be empty. So remove this code.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On K2HK, sgmii module registers of slave 0 and 1 are mem
mapped to one contiguous block, while those of slave 2
and 3 are mapped to another contiguous block. However,
on K2E and K2L, sgmii module registers of all slaves are
mem mapped to one contiguous block. SGMII APIs expect
slave 0 sgmii base when API is invoked for slave 0 and 1,
and slave 2 sgmii base when invoked for other slaves.
Before this patch, slave 0 sgmii base is always passed to
sgmii API for K2E regardless which slave is the API invoked
for. This patch fixes the problem.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a timer to each rocker switch to do FDB entry cleanup by ageing out
expired entries. The timer scheduling algo is copied from the bridge
driver, for the most part, to keep the firing of the timer to a minimum.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up patcheset will allow user to change ageing_time, but for now
just hard-code it to a fixed value (the same value used as the default
for the bridge driver).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need more info from rocker_port than just pport when we age out fdb
entries, so store rocker_port rather than pport in each fdb entry.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry is touched once when created, and touched again for each update.
The touched time is used to calculate FDB entry age.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable can store negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_mode can be negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the bit banging mode in the hardware when performing bit banging
I2C operations on X550. Also control the output enable on both the
clock and data lines.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lan_id is being set after a previous I2C eeprom access which
makes no sense because it needs to be set before any access. Move
the setting to before the access.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most I2C accesses take and release semaphores for each access. Now
there is a reason to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide I2C combined operations on X550EM, not X550 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the SFP insertion interrupt on X550EM devices with
SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with 82599ES.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I217-LM.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I350.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device probe method e1000_probe calls e1000_init_eeprom_params
itself so there's no reason to call it again from e1000_do_write_eeprom
or e1000_do_read_eeprom.
The sentence above assumes that e1000_init_eeprom_params is effective.
e1000_init_eeprom_params depends mostly on hw->mac_type and e1000_probe
bails out early if it can't set mac_type (see e1000_init_hw_struct, then
e1000_set_mac_type), qed.
Btw, if effective, the removed paths would had been deadlock prone when
e1000_eeprom_spi was set:
-> e1000_write_eeprom (takes e1000_eeprom_lock)
-> e1000_do_write_eeprom
-> e1000_init_eeprom_params
-> e1000_read_eeprom (takes e1000_eeprom_lock)
(same narrative with e1000_read_eeprom -> e1000_do_read_eeprom etc.)
As a final note, the candidate deadlock above can't happen in e1000_probe
due to the way eeprom->word_size is set / tested.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a private ethtool flag to enable display of these statistics, which
are generally less useful. However, sometimes it can be useful for
debugging purposes. The most useful portion is the ability to see what
the PF thinks the VF mailboxes look like.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we connect to the mailbox, we insert a fake disconnect header so
that the code does not see an invalid header and thus instantly error
every time we bring up the mailbox. However, we incorrectly record the
tail and head from the local perspective. Since the remote end shouldn't
have anything for us, add a "create_fake_disconnect_hdr" function which
inverts the TAIL and HEAD fields. This enables us to connect without any
errors of either TAIL or HEAD incorrectness, and prevents creating
extraneous error messages. This is necessary now since mbx_reset_work
does not actually reset the Tx FIFO head and tail pointers, thus head
and tail might not be equivalent on a reconnect.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a corner case issue with the PF/VF mailbox code.
Currently, fm10k_mbx_reset_work clears various state about the mailbox.
However, it does not clear the Tx FIFO head/tail pointers. We can't
simply clear these pointers as we unintentionally drop untransmitted
messages without error.
Doing nothing results in a possible phantom re-transmission of messages,
since we leave tx.head and tx.tail intact, but clear the tx_pulled and
tail_len values. This means that the PF could continuously re-send a
message which triggers a reset in the VF. Upon reset, the VF will
re-receive the same message after a reconnect.
If we reset the tx.head and tx.tail pointers completely, we end up
dropping some messages that were pending before connect. This results in
missing LPORT_MSG_READY bits, and VFs will end up reporting no link.
However, we can resolve both issues by simply incrementing head to
account for the already transmitted messages, before we reset tx_pulled.
We do this via the same logic as fm10k_mbx_head_pull.
We account for the tail_len which includes all data not yet transmitted,
once we account for the acked data which means re-reading the HEAD
variable from the message header. Then, we drop messages until we've
dropped more than the new tx_pulled value. At this point, resetting
tail_len and tx_pulled, but not tx.head and tx.tail will result in
prevention of the phantom message. It also prevents us from dropping
untransmitted messages upon attempting to Tx into a connect or
disconnect header.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 has HW support for SCTP flow director filters SCTP mask. This
patch adds it like we do for UDP and TCP.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is part of the future enablement of X550 SFP+ support. This
HW uses different SDP so the interrupts need to be set up accordingly.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This comment is no longer true due to a couple of mailbox locking
refactors, and we now don't actually do any rtnl protected operations
directly in the mailbox path. Remove this comment as it is factually
incorrect and confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding support for reading mac address using syscon driver for
dra7 and am437x platforms
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving mac address reading from ethernet driver to common
file for better maintenance and for code reusable.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ls /sys/devices/channel-devices/vnet-port-0-0/net' is missing without
this change, and applications like NetworkManager are looking in
sysfs for the information.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking twice for ec->tx_coalesce_usecs_high, remove the
duplicate test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild-all@01.org
Fixes: 2f9130709d ("net: bcmgenet: Implement TX coalescing control knobs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-17
This series contains updates to i40e and i40evf.
Shannon provides updates to i40e and i40evf to resolve an issue with the
nvmupdate utility. First renames a variable name to reduce confusion and
to differentiate it from the actual user variable. Then added the ability
to save the admin queue write back descriptor if a caller supplies a
buffer for it to be saved into. Added a new GetStatus command so that
the NVM update tool can query the current status instead of doing fake
write requests to probe for readiness. Added wait states to the NVM
update state machine to signify when waiting for an update operation to
finish, whether we are in the middle of a set of write operations, or we
are now idle but waiting. Then added a facility to run admin queue
commands through the NVM update utility in order to allow the update
tools to interact with the firmware and do special commands needed for
updates and configuration changes. Also added a facility to recover the
result of a previously run admin queue command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unless we reset the RX config, on real hardware I don't seem to receive
any packets after a TX timeout.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be called from cp_tx_timeout() with interrupts disabled.
Spotted by Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to add basic ethernet support for HNS. It is one of the way to
use the HNS acceleration engine. But most of the decoding/encoding
capability of the AE cannot be used in this way.
This submit contains the basic feature as a ethernet driver. More will
be added later.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSAF, namely Distributed System Area Fabric, is one of the HNS
acceleration engine implementation. This patch add DSAF driver to the
system.
hns_ae_adapt: the adaptor for registering the driver to HNAE framework
hns_dsaf_mac: MAC cover interface for GE and XGE
hns_dsaf_gmac: GE (10/100/1000G Ethernet) MAC function
hns_dsaf_xgmac: XGE (10000+G Ethernet) MAC function
hns_dsaf_main: the platform device driver for the whole hardware
hns_dsaf_misc: some misc helper function, such as LED support
hns_dsaf_ppe: packet process engine function
hns_dsaf_rcb: ring buffer function
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNAE (Hisilicon Network Acceleration Engine) is a framework to provide a
unified ring buffer interface for Hisilicon Network Acceleration
Engines.
With the interface, upper layer can work as ethernet driver, ODP driver
or other service driver on purpose.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO support for Hisilicon Network Subsystem. It is used in Hislicon
hip04, hip05 and Hi1610 SoC to control the external PHY
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for DMA mapping errors, recover from them and register them in
ethtool stats like other errors.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for both
IPv4 and IPv6. Do not disable the offloading if this occurs.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.
We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.
We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.
Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.
While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing rss key, we do not want to overwrite user provided key
by the one provided by netdev_rss_key_fill(), which is the host random
key generated at boot time.
Fixes: 947cbb0ac2 ("net/mlx4_en: Support for configurable RSS hash function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eyal Perry <eyalpe@mellanox.com>
CC: Amir Vadai <amirv@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a facility to recover the result of a previously run AQ command.
Change-ID: I21afec2c20c1a5e6ba60c7fbfcbedfff78c10e45
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a facility to run AQ commands through the nvmupdate utility in order
to allow the update tools to interact with the FW and do special
commands needed for updates and configuration changes.
Change-ID: I5c41523e4055b37f8e4ee479f7a0574368f4a588
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds wait states to the NVM update state machine to signify when
waiting for an update operation to finish, whether we're in the middle
of a set of Write operations, or we're now idle but waiting.
Change-ID: Iabe91d6579ef6a2ea560647e374035656211ab43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds a new GetStatus command so that the NVM update tool can query
the current status instead of doing fake write requests to probe for
readiness.
Change-ID: I671ec6ccd4dfc9dbac3a03b964589d693fda5cd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the writeback descriptor buffer was previously created, this gives it
to the AQ command request to be used to save the results.
Change-ID: I8c8a1af81e6ebed6d0a15ed31697fe1a6c4e3708
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ability to save the AdminQ write back descriptor if a
caller supplies a buffer for it to be saved into.
Change-ID: I3d1301d26360b39a2d66dc8569e851f54133a3af
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code returns something that becomes the errno value from ethtool and
passes around a pointer to an errno variable. This patch changes the name
slightly to differentiate it from the actual user errno variable.
Change-ID: Idaa37845c069e66f4cea072e90f471bb2142454d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-15
This series contains updates to ixgbe and fm10k.
Don fixes a ixgbe issue by adding checks for systems that do not have
SFP's to avoid incorrectly acting on interrupts that are falsely
interpreted as SFP events.
Alex Williamson adds a fix for ixgbe to disable SR-IOV prior to
unregistering the netdev to avoid issues with guest OS's which do not
support hot-unplug or their hot-unplug is broken.
Alex Duyck update the lowest limit for adaptive interrupt interrupt
moderation to about 12K interrupts per second for ixgbe. This change
increases the performance for ixgbe. Also fixed up fm10k to remove
the optimization that assumed that all fragments would be limited to
page size, since that assumption is incorrect as the TCP allocator can
provide up to a 32K page fragment. Updated fm10k to add the MAC
address to the list of values recorded on driver load. Fixes fm10k
so that we only trigger the data path reset if the fabric is ready to
handle traffic to avoid triggering the reset unless the switch API is
ready for us.
Jacob updates the fm10k driver to disable the service task during
suspend and re-enable it after we resume. If we don't do this, the
device could be UP when you suspend and come back from resume as
DOWN. Also update fm10k to prevent the removal of default VID rules,
and correctly remove the stack layers information of the VLAN, but then
return to forwarding that VID as untagged frames. If we deleted the VID
rules here, we would begin dropping traffic due to VLAN membership
violations. Fixed fm10k to use pcie_get_minimum_link(), which is useful
in cases where we connect to a slot at Gen3, but the slot is behind a bus
which is only connected at Gen2. Updated fm10k to update the netdev
permanent address during reinit instead of up to enable users to
immediately see the new MAC address on the VF even if the device is not
up. Adds the creation of VLAN interfaces on a device, even while the
device is down for fm10k. Fixed an issue where we request the incorrect
MAC/VLAN combinations, and prevents us from accidentally reporting some
frames as VLAN tagged. Provided a couple of trivial fixes for fm10k
to fix code style and typos in code comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the dma transfers to be dmaengine based, now pxa has a dmaengine
slave driver. This makes this driver a bit more PXA agnostic.
The driver was tested on pxa27x (mainstone) and pxa310 (zylonite),
ie. only pxa platforms.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
