After exchanging PLOGI on an SLI-3 adapter, the PRLI exchange failed. Link
trace showed the port was assigned a non-zero n_port_id, but didn't use the
address on the PRLI. The assigned address is set on the port by the
CONFIG_LINK mailbox command. The driver responded to the PRLI before the
mailbox command completed. Thus the PRLI response used the old n_port_id.
Defer the PRLI response until CONFIG_LINK completes.
Link: https://lore.kernel.org/r/20190922035906.10977-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but avoids that the compiler
complains about set-but-not-used variables when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conversion to enable SCSI and NVME fc4 support ran into an issue with
NPIV support. With NVME, NPIV is not currently supported, but with SCSI it
was. The driver reverted to its lowest setting meaning NPIV with SCSI was
not allowed.
Convert the NPIV checks and implementation so that SCSI can continue to
allow NPIV support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands. The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port. During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.
Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.
Filter out multiple UNREG_RPIs being queued up for the same remote port.
Beef up log messages in this area.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An address change for a remote port cause PRLI for the wrong protocol
to be sent. The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.
Fix the copy logic for the address change. Beefed up log messages in
this area as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a LOGO in response to an ABTS timeout, a PLOGI wasn't issued to
re-establish the login. An nlp_type check in the LOGO completion
handler failed to restart discovery for NVME targets. Revised the
nlp_type check for NVME as well as SCSI.
While reviewing the LOGO handling a few other issues were seen and
were addressed:
- Better lock synchronization around ndlp data types
- When the ABTS times out, unregister the RPI before sending the LOGO
so that all local exchange contexts are cleared and nothing received
while awaiting LOGO/PLOGI handling will be accepted.
- LOGO handling optimized to:
Wait only R_A_TOV for a response.
It doesn't need to be retried on timeout. If there wasn't a
response, a PLOGI will be sent, thus an implicit logout
applies as well when the other port sees it.
If there is a response, any kind of response is considered "good"
and the XRI quarantined for a exchange qualifier window.
- PLOGI is issued as soon a LOGO state is resolved.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance is affected when target queue depth is tracked. An atomic
counter is incremented on the submission path which competes with it being
decremented on the completion path. In addition, multiple CPUs can
simultaniously be manipulating this counter for the same ndlp.
Reduce the overhead by only performing the target increment/decrement when
the target queue depth is less than the overall adapter depth, thus is
actually meaningful.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI
combination. For ELS aborts, driver specifies IOTAG correctly but RPI is
not specified.
Fix by setting RPI in WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change references from "Broadcom Limited" to "Broadcom Inc." in the
copyright message. Update copyright duration if not yet updated for 2018.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under large configurations, the driver would start to log message 6065 -
NVME out of buffers (exchanges).
The driver is using the ndlp cmd_qdepth value when determining the max
outstanding ios for an adapter. This value, by default, is set to 65536,
which exceeds the maximum exchange counts supported on an adapter. The ndlp
cmd_qdepth has no relevance and outstanding io count should be capped at
the max exchange count with IO requests beyond that level getting bounced
back with an EBUSY status so that they are retried by the block layer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nodelist entry for SCSI array ends up in UNMAPPED state. This is due to
illegal discovery State machine transition because of two PRLIs and the
first one failing with LS_RJT. Also, the error path was designed
assuming the PRLIs complete in the order they were sent, FCP first, then
NVME. In a failing case, the array thinks about the first PRLI (FCP),
but issues LS_RJT for the 2nd PRLI immediately.
Fix PRLI completion error path for the ordering expectation. Ensure the
discovery state machine update is not set until all outstanding PRLIs
are complete.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
First Burst support was not properly indicated in NVMe PRLI.
Correct the bit position and the logic to check and set first burst support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise the NVME PRLI to indicate CONF support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lpfc discovery engine, when as a nvme target, where the driver
was performing mailbox io with the adapter for port login when a NVME
PRLI is received from the host. Rather than queue and eventually get
back to sending a response after the mailbox traffic, the driver
rejected the io with an error response.
Turns out this particular initiator didn't like the rejection values
(unable to process command/command in progress) so it never attempted a
retry of the PRLI. Thus the host never established nvme connectivity
with the lpfc target.
By changing the rejection values (to Logical Busy/nothing more), the
initiator accepted the response and would retry the PRLI, resulting in
nvme connectivity.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabled for both SCSI and NVME support, and connected pt2pt to a
SCSI only target, the driver nodelist entry for the remote port is left
in PRLI_ISSUE state and no SCSI LUNs are discovered. Works fine if only
configured for SCSI support.
Error was due to some of the prli points still reflecting the need to
send only 1 PRLI. On a lot of fabric configs, targets were NVME only,
which meant the fabric-reported protocol attributes were only telling
the driver one protocol or the other. Thus things worked fine. With
pt2pt, the driver must send a PRLI for both protocols as there are no
hints on what the target supports. Thus pt2pt targets were hitting the
multiple PRLI issues.
Complete the dual PRLI support. Track explicitly whether scsi (fcp) or
nvme prli's have been sent. Accurately track protocol support detected
on each node as reported by the fabric or probed by PRLI traffic.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handling a rcv'ed PRLI incorrectly can cause the ndlp to end up in the
wrong state or the driver to ACC and PRLI when it should send LS_RJT.
The cause was due to the driver not properly looking at the PRLI type
and taking the multiple protocol support into consideration.
Resolved by adding checks in the various PRLI receive points to validate
PRLI type and reject if not valid for the enabled protocols and mode
(host vs target).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After link bounce in a NVME Pt2Pt config, the driver managed to map the
same nport twice, resulting in multiple device nodes for the same
namespace.
In Pt2Pt, the driver must send PRLI's for both (scsi) FCP and NVME
rather than using fabric aids. The driver was inconsistent on handling
various PRLI completions, especially rejects, which had reject codes
cross the different protocol PRLI completions.
Fixed to perform the following: if nvmet mode (fc port can only be a
nvme target) - rejects all unsolicitly FCP PRLI's. Never issues a FCP
PRLI.
The multiple protocol PRLI's are sent simultaneously. However, driver
will now only state transition after both PRLI's are complete. New flags
were added to aid tracking the responses from the different PRLI's.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the switch blade is pulled out then plugged back in, the driver
does not issue a PLOGI to the target
When the switch blade is pulled out, it does not reset the link. The
driver ends up issuing a LOGO to the target, and finally sees devloss.
Since the driver believes that a LOGO is outstanding, it does not issue
a PLOGI to the target upon link up
Correct by placing the ndlp in UNUSED state When devloss happens in
LOGO_ISSUE state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver does not discover targets when in loop mode.
The NLP type is correctly getting set when a fabric connection is
detected but, not for loop. The unknown NLP type means that the driver
does not issue a PRLI when in loop topology. Thus target discovery
fails.
Fix by checking the topology during discovery. If it is loop, set the
NLP FC4 type to FCP.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We might have a NULL pring in lpfc_els_abort(), for example on error
recovery path, since queues are destroyed during error recovery
mechanism.
In this case, we should just drop the abort since the queues will be
recreated anyway. This patch just verifies for NULL pointer and stop the
abortion of the queue in case of a NULL pring.
Also, this patch converts return type of lpfc_els_abort() from int to
void, since it's not checked anywhere.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code review of NVMEI's FC_PORT_ROLE_NVME_DISCOVERY looked wrong.
Discussions with storage architecture team clarified NVMEI's audit of
the PRLI response port roles. Following up discussion with code review
showed a few minor corrections were required - especially in
anticipation of NVME auto discovery.
During PRLI, NVMEI should sent prli_init - which it it does. NVMET
should send prli_tgt and prli_disc - which it does. When NVMEI receives
a PRLI Response now, it audits the incoming target bits and stores the
attributes in the corresponding NDLP. Later, when NVMEI registers the
NVME rport, it uses the stored ndlp attributes to set the rport
port_roles correctly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVMET didn't have any RSCN handling at all and
would not execute implicit LOGO when receiving a PLOGI
from an rport that NVMET had in state UNMAPPED.
Clean up the logic in lpfc_nlp_state_cleanup for
initiators (FCP and NVME). NVMET should not respond to
RSCN including allocating new ndlps so this code was
conditionalized when nvmet_support is true. The check
for NLP_RCV_PLOGI in lpfc_setup_disc_node was moved
below the check for nvmet_support to allow the NVMET
to recover initiator nodes correctly. The implicit
logo was introduced with lpfc_rcv_plogi when NVMET gets
a PLOGI on an ndlp in UNMAPPED state. The RSCN handling
was modified to not respond to an RSCN in NVMET. Instead
NVMET sends a GID_FT and determines if an NVMEP_INITIATOR
it has is UNMAPPED but no longer in the zone membership.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Target: Merge into FC discovery
Adds NVME PRLI handling and Nameserver registrations for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Tie in to NVME Fabrics nvme_fc LLDD initiator api
Adds the routines to:
- register and deregister the FC port as a nvme-fc initiator localport
- register and deregister remote FC ports as a nvme-fc remoteport
- binding of nvme queues to adapter WQs
- send/perform NVME LS's
- send/perform NVME FCP initiator io operations
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Merge into FC discovery
Adds NVME PRLI support and Nameserver registrations and Queries for NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME Initiator: Base modifications
This patch adds base modifications for NVME initiator support.
The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
SCSI initiator only; NVME initiator only; NVME target only; and
SCSI and NVME initiator.
The configuration mode drives overall adapter configuration,
offloads enabled, and resource splits.
NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
- Exchange resources are split by protocol; Obviously, if only
1 mode, then no split occurs. Default is 50/50. module attribute
allows tuning.
- Pools and config parameters are separated per-protocol
- Each protocol has it's own set of queues, but share interrupt
vectors.
SCSI:
SLI3 devices have few queues and the original style of queue
allocation remains.
SLI4 devices piggy back on an "io-channel" concept that
eventually needs to merge with scsi-mq/blk-mq support (it is
underway). For now, the paradigm continues as it existed
prior. io channel allocates N msix and N WQs (N=4 default)
and either round robins or uses cpu # modulo N for scheduling.
A bunch of module parameters allow the configuration to be
tuned.
NVME (initiator):
Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
gets)
Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
modulo msix vector count basis.
Module parameters exist to cap/control the config if desired.
- Each protocol has its own buffer and dma pools.
I apologize for the size of the patch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a link bounce, when a remote port issues a LOGO while a REGLOGIN
is pending on that port, the driver does not clean up the ndlp
structure. May result in stack traces in the console log.
Fix: Clear the NLP_REG_LOGIN_SEND flag on the ndlp in the routine
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix mbox reuse in PLOGI completion. Moved allocations so that buffer
properly init'd.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix RegLogin failed error seen on Lancer FC during port bounce
Fix the statemachine and ref counting.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the FLOGI discovery logic to comply with T11 standards
We weren't properly setting fabric parameters, such as R_A_TOV and E_D_TOV,
when we registered the vfi object in default configs and pt2pt configs.
Revise to now pass service params with the values to the firmware and
ensure they are reset on link bounce. Required reworking the call sequence
in the discovery threads.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove set but not used variables.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The domain controller PLOGI's concurrent with prior LOGO's/unreg_rpi's
completing created a race condition where driver rpi ref count can
inadvertantly hit 0 and the rpi attempted to be freed. This error
sometimes resulted in Warning messages indicating kref.h via
lfpc_nlp_get+0x128.
Correct by dropping any new PLOGI until the prior nport state has settled.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We inadvertantly took the path to recreate the vport while in a
driver teardown path
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Update copyright to 2015
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
